Caracterização e desenvolvimento de argilas para aplicação em nanocompósitos poliméricos

O Brasil é produtor de argilas e conta com grandes reservas deste recurso natural. Porém, grande parte da sua produção é comercializada seca e moída. O desenvolvimento de argilas para seu uso como reforço em nanocompósitos poliméricos constitui uma opção para os produtores desta matéria prima que teriam assim um produto com maior valor agregado. Este trabalho visa avaliar o potencial uso como nanocarga de duas argilas nacionais provenientes da Bacia de Taubaté, São Paulo, denominadas ALIGRA e SANTA FÉ. As frações de tamanho de partícula médio menor de 0,02 mm, obtidas por peneiramento á úmido da argila homogeneizada e seca, foram utilizadas no desenvolvimento do trabalho experimental. Os estudos de caracterização, envolvendo análise granulométrica, química, mineralógica, morfológica, térmica e textural, revelaram características muito semelhantes em ambas às argilas. Fração argila, maior de 70% em massa. Composição química conforme a definição química de uma argila e os teores de seus componentes mostram valores intermédios entre as apresentadas pelas bentonitas e argila caulinítica usadas com fins de comparação. Ressaltamse boas propriedades adsorventes. Área superficial específica BET ao redor de 120 m2/g, valor maior do que o apresentado por muitas bentonitas naturais (74,5 m2/g). Predominantemente mesoporosas, com poros, maiormente em forma de fenda, característicos da estrutura em camadas das argilas. Baixa capacidade de troca catiônica, 12 meq/100g. Difratogramas de raios-X revelaram a predominância do estratificado ilita/esmectita, caulinita e quartzo na argila ALIGRA, e de ilita, caulinita e quartzo na argila SANTA FÉ. Prosseguiu-se com a argila ALIGRA a preparação da argila organofílica. A argila organofílica foi obtida por troca catiônica com o sal quaternário de amônio: cloro cetril trimetil amônio, depois de homogeneizada em sódio com cloreto de sódio. Análises FTIR e TGA indicaram que houve inserção dos cátions orgânicos. Testes preliminares foram feitas, preparando misturas das argilas com matriz de polipropileno e usando como agente compatibilizante polipropileno enxertado com anidrido maleico. Resultados de ensaios de tração reportam algumas melhoras nas propriedades testadas com as composições preparadas com as argilas purificadas. Com as composições com argilas organofílicas somente foi melhorado o alongamento na rotura. Estudos ais aprofundados são recomendados.

Comparison between granular pillared, organo- and inorgano-organo-bentonites for hydrocarbon and metal ion adsorption

Granular reactive materials have higher permeability and are therefore desirable for in situ groundwater pollution control. Three granular bentonites were prepared: an Al-pillared bentonite (PBg), an organo-bentonite (OBg) using a quaternary ammonium cation (QAC), and an inorgano-organo-bentonite (IOBg), using both the pillaring agent and the QAC. Powdered IOB (IOBp) was also prepared to test the effect of particle size. The modified bentonites were characterised with X-ray diffraction (XRD), Fourier transform infrared spectrometry (FT-IR), thermal gravimetric analysis (TGA) and uniaxial compression tests. The d-spacing increased only with QAC intercalation. The Young's modulus of IOBg was twice as high as OBg. Batch adsorption tests were performed with aqueous multimetal solutions of Pb2+, Cu2+, Cd2+, Zn2+ and Ni2+ ions, with liquid dodecane and with aqueous dodecane solutions. Metal adsorption fit the Langmuir isotherm. Adsorption occurred within 30min for PBg, while the granular organo-bentonite needed at least 12h to reach equilibrium. IOBp had the maximum adsorption capacity at higher metal concentration and lower adsorbent content (Cu2+: 2.2, Ni2+: 1.7, Zn2+: 1.4, Cd2+: 0.9 and Pb2+: 0.7 all in mmolg-1). The dual pillaring of the QAC and Al hydroxide increased the adsorption. The adsorption of liquid dodecane was in the order IOBg>OBg>PBg (3.2>2.7>1.7mmolg-1). Therefore IOBg has potential for the removal of toxic compounds found in soil, groundwater, storm water and wastewater. © 2012 Elsevier B.V.

糖原酸酯合成方法的研究以及二环糖胺的合成

在糖化学中，糖原酸酯是一类重要的合成中间体，广泛运用于1,2-反式糖苷的合成，尤其对于寡糖的立体选择性合成具有重要的价值。目前文献报道的制备糖原酸酯的方法大多存在对环境不友好的问题。本文对传统的糖原酸酯制备方法进行了改进，通过研究发现无机碱也能够有效地催化合成糖原酸酯。以溴代糖和醇（或糖基受体）为原料，在无机碱、四丁基溴化铵、乙腈的体系中，合成了一系列简单醇糖原酸酯和糖-糖原酸酯。 聚乙二醇及其衍生物作为有机反应的溶剂和催化剂在有机化学中有广泛的应用。本文阐述了一种以溴代糖和醇（或糖基受体）为原料，在无机碱和聚乙二醇二甲醚反应体系中合成糖原酸酯的方法。该方法中，聚乙二醇二甲醚即作为绿色溶剂又作为催化剂，反应条件温和、环保、高效。 糖胺是一类重要的糖苷酶抑制剂，已在糖尿病和其他代谢紊乱等疾病的治疗中发挥了极其重要的作用。本文提供了一种合成一类具有潜在的糖苷酶抑制活性、结构新颖的二环糖胺的途径。该合成思路是以1-叠氮基-2-C-乙酰甲基-3,4,6-三-O-苄基-2-脱氧-β-D-葡萄糖为原料，经二环糖亚胺中间体，通过二环糖亚胺还原或加成得到一类二环糖胺。 Sugar orthoesters as one of the most important intermediates in carbohydrate chemistry, are used extensively in the synthesis of sugar 1,2-trans-glycosides, especially oligosaccharide. These methods in the literature are mostly eco-unfriendly. Herein we described a modified protocol for the preparation of sugar orthoesters using inorganic base, by improving the conventional method. Our method involves the treatment of peracetylated or perbenzotlated glycosyl bromides with alcohols in the presence of a quaternary ammonium salt and an inorganic alkali in acetonitrile solvent, affording both simple sugar orthoesters and sugar-sugar orthoesters. Polyethylene glycol and their derivatives as solvents or catalysts play a significant role in the organic reaction. We developed a novel and environmentally benign methodology towards the synthesis of sugar orthoesters, which are prepared by the reaction of peracetylated or perbenzotlated glycosyl bromides and alcohols in the presence of dimethyl ether of polyethylene glycol as either the reaction medium or catalyst. Glycosylamines and pseudo-glycosylamines have been tested against various glycosidases, and applied to the treatment of diabetes and other metabolic disorders. We presented a route of the synthesis of a bicyclic glycosylamine as a potential glycosidases inhibitor with unique structure. Reduction of 2-C-acetlymethyl-β-glucopyranosyl azide derivative firstly produced a bicyclic glycosylimine intermediate, and subsequently the bicyclic glycosylamine and its derivatives would be prepared through the selective reduction or addition the C=N double bond of the bicyclic glycosylimine intermediate.

Purification and structure identification of hyaluronic acid

Polysaccharide produced by mutated strain of Streptococcus zooepidemicus was purified by the procedures including Savage method, quaternary ammonium compound precipitation, DEAE-cellulose(DE52) chromatography and Sephadex G-75 gel filtration. The structure of the purified polysaccharide has been characterized by means of chemical composition analysis, C-13 NMR spectrum, infrared spectrum and circular dichroism (CD). All the results showed that the purified polysaccharide was hyaluronic acid (HA). The single helix conformation of the purified HA was determined by Congo red experiment. The molecular weight of the HA was about 1.16x10(6)D, which was measured by viscosity method.

One-step preparation and characterization of PDDA-protected gold nanoparticles

Poly(diallyl dimethylammonium) chloride (PDDA), an ordinary and watersoluble, cationic polyelectrolyte, was investigated for its ability to generate and stabilize gold colloids from a chloroauric acid precursor. In this reaction, PDDA acted as both reducing and stabilizing agents for gold nanoparticles (AuNPs). More importantly, PDDA is a quaternary ammonium polyelectrolyte, which shows that the scope of the reducing and stabilizing agents for metal nanoparticles can be extended from the amine-containing molecules to quaternary ammonium polyelectrolytes or salts. UV-vis spectroscopy, transmission electron microscopy (TEM), X-ray photoelectron spectra (XPS) and Fourier transform infrared (FTIR) were used to characterize the synthetic AuNPs. The PDDA-protected AuNPs obtained are very stable and have relative narrow size distribution.

Probe beam deflection combined with cyclic voltammetry studies of C-60-modified electrode film

C-60 films, prepared by solution casting, were studied by means of in situ probe beam deflection (PBD) combined with cyclic voltammetry (CV). PBD is a powerful technique for investigation of phenomena at the electrode/electrolyte interface in acetonitrile with quaternary ammonium and alkali metal salts as supporting electrolytes. In tetra-n-butylammonium (TBA(+)) salt solution, a stable CV can be obtained during the first two reduction/reoxidation waves. On reduction, injection of cations to maintain charge balance and dissolution of small amount of C-60(-) (TEA(+)) and/or C-60(2-) (TBA(+))(2) are detected. During the reoxidation process ejection of cations and injection of anions occur simultaneously, especially for the second reoxidation wave. In the case where TBABr is the supporting electrolyte, the accompanied behavior is more complicated than in TBABF(4), TBAClO(4), and TBAPF(6) solutions. A small pair of prewaves in CV are proposed due to oxidation/reduction of C-60 domains but not dissolution/redeposition of C-60 film. Extending the potential scan range to the third reduction wave, no apparent corresponding reoxidation wave is related to the third reduction wave, the electroactivity of the film disappears rapidly and dissolution of C-60 film is observed. In tetraethylammonium (TEA(+)) and NAClO(4) solutions, the electrochemistry of the C-60 films is unstable, and potential scans lead to dissolution of flaking of the film.

Capillary electrochromatography using a strong cation-exchange column with a dynamically modified cationic surfactant

A novel mode of capillary electrochromatography (CEC), called dynamically modified strong cation-exchange CEC (DMSCX-CEC), is described in this paper. A column packed with a strong cation-exchange (SCX) packing material was dynamically modified with a long-chain quaternary ammonium salt, cetyltrimethylammonium bromide (CTAB), which was added to the mobile phase. CTAB ions were adsorbed onto the surface of the SCX packing material, and the resulting hydrophobic layer on this packing was used as the stationary phase. Using the dynamically modified SCX column, neutral solutes were separated with the CEC mode. The highest number of theoretical plates obtained was about 190 000/m, and the relative standard deviations (RSD's) for migration times and capacity factors of alkylbenzenes were less than 1.0% and 2.0% for five consecutive runs, respectively. The effects of CTAB and methanol concentrations and the pH value of the mobile phase on the electroosmotic flow and the separation mechanism were investigated. Excellent simultaneous separation of the basic and neutral solutes in DMSCX-CEC with a high-pH mobile phase was obtained, A mixture containing the acidic, basic, and neutral compounds was well separated in this mode with a low-pH mobile phase; however, peak tailing for basic compounds was observed in this mobile phase.

Capillary electrochromatography with a silica column with a dynamically modified cationic surfactant

A novel mode of capillary electrochromatography (CEC), called dynamically modified silica-capillary electrochromatography, is described in this paper. The column packed with bare silica was dynamically modified with long chain quaternary ammonium salt, cetyltrimethylammonium bromide (CTAB), which was added into the mobile phase. CTAB ions were adsorbed onto the surface of bare silica, and the resulted hydrophobic layer on the silica gel was used as the stationary phase; Using the dynamically modified silica column, neutral solutes were separated by CEC. The highest number of theoretical plates obtained was about 71 500/m and the relative standard deviations for t(0) and capacity factor of toluene were 4.7% and 4.9% for 20 consecutive runs, respectively. The separation mechanism of neutral solutes and the influence of mobile phase composition on the separation was investigated. The separation of nitrogen-containing solutes was carried out with this mode and the peak tailing of basic solute was effectively eliminated because the adsorption of basic solute on silica was blocked by the preferred adsorption of CTAB. (C) 1999 Elsevier Science B.V. All rights reserved.

Selective oxidations on recoverable catalysts assembled in emulsions

Catalysts assembled in emulsions are found to be potentially recoverable and efficient for a number of catalytic reactions. The catalysts composed of polyoxometalate anions and quaternary ammonium cations have been designed and synthesized according to the catalytic reactions and by optimizing the structures of cations and anions. The catalysts act essentially as surfactants, which are uniformly distributed in the interface of the emulsion droplets, and accordingly behave like homogeneous catalysts. The catalysts show remarkable selectivity and activity in the oxidation of sulfur-containing molecules to sulfones in diesel and the selective oxidation of alcohols to ketones, using H2O2 as oxidant. For an example, the catalyst demonstrated over 96% efficiency of H2O2 and similar to 100% selectivity to sulfones for the selective oxidation of sulfur-containing molecules in real diesel. Moreover, the catalysts can be separated and recycled by a simple demulsification and re-emulsification.

Phase transition and decomposition temperatures, heat capacities and viscosities of pyridinium ionic liquids

Ionic liquids are organic salts with low melting points. Many of these compounds are liquid at room temperature in their pure state. Since they have negligible vapor pressure and would not contribute to air pollution, they are being intensively investigated for a variety of applications, including as solvents for reactions and separations, as non-volatile electrolytes, and as heat transfer fluids. We present melting temperatures, glass transition temperatures, decomposition temperatures, heat capacities, and viscosities for a large series of pyridinium-based ionic liquids. For comparison, we include data for several imidazolium and quaternary ammonium salts. Many of the compounds do not crystallize, but form glasses at temperatures between 188 K and 223 K. The thermal stability is largely determined by the coordinating ability of the anion, with ionic liquids made with the least coordinating anions, like bis(trifluoromethylsulfonyl)imide, having the best thermal stability. In particular, dimethylaminopyridinium bis(trifluoromethylsulfonyl)imide salts have some of the best thermal stabilities of any ionic liquid compounds investigated to date. Heat capacities increase approximately linearly with increasing molar mass, which corresponds with increasing numbers of translational, vibrational, and rotational modes. Viscosities generally increase with increasing number and length of alkyl substituents on the cation, with the pyridinium salts typically being slightly more viscous than the equivalent imidazolium compounds. (c) 2005 Elsevier Ltd. All rights reserved.

Selective oxidation of a pyrimidine thioether using supported tantalum catalysts

Ta2O5-SiO2 catalysts were prepared by a sol-gel method using tetraethyl orthosilicate (TEOS) and tantalum (V) ethoxide as the sources of silicon and tantalum, and two families of quaternary ammonium salts, [CnH(2n+1)(CH3)(3)N]Br (n = 14, 16, 18) and [(CnH(2n+1))(4)N]Br (n = 10, 12, 16, 18) as surfactants. The catalysts were compared for the selective suffoxidation of 4,6-dimethyl-2-thiomethylpyrimidine using peroxide as an oxidising agent in a range of ionic liquids and organic solvents. The sol-gel catalysts were also compared with tantalum on MCM-41 prepared by grafting. The catalysts were characterized from adsorption-desorption isotherms of N-2, XRD patterns, small-angle X-ray scattering, IR spectra from adsorbed pyridine and CDCl3, XPS spectra, and Si-29 magic angle spinning (MAS) NNIR experiments. The effect of recycling on the catalyst leaching and selectivity/activity was also studied. High activities and selectivities were found in [NTf2](-) based ionic liquids and organic solvents with good recyclability of the catalyst. Tantalum was found in the solution after reaction; however, this was determined to be due to entrapment of catalyst particulates, as opposed to leaching of the active metal. (c) 2005 Elsevier Inc. All rights reserved.

High-surface thermally stable mesoporous gallium phosphates constituted by nanoparticles as primary building blocks

In constant, search for micro/mesoporous materials, gallium phosphates, have attracted continued interest due to the large pore size reported for some of these solids in comparison with analogous aluminum phosphates. However up to now, the porosity of gallium phosphates collapsed upon template removal or exposure to the ambient moisture. In the present work, we describe high-surface thermally stable mesoporous gallium phosphates synthesized from gallium propoxide and PCl3 and different templating agents such as amines (dipropylamine, piperidine and aminopiperidine) and quaternary ammonium salts (C16H33(CH3)3NBr and C16PyCl). These highly reactive precursors have so far not been used as gallium and phosphate sources for the synthesis of gallophosphates. Conceptually, our present synthetic procedure is based on the fast formation of gallium phosphate nanoparticles via the reaction of gallium propoxide with PCl3 and subsequent construction of the porous material with nanoparticles as building blocks. The organization of the gallophosphate nanoparticles in stable porous structures is effected by the templates. Different experimental procedures varying the molar composition of the sol-gel, pH and the pretreatment of gallium precursor were assayed, most of them leading to satisfactory materials in terms of thermal stability and porosity. In this way, a series of gallium phosphates with surface are above 200 m(2) g(-1), and narrow pore size from 3 to 6 nm and remarkable thermal stability (up to 550 degrees C) have been prepared. In some cases, the structure tends to show some periodicity and regularity as determined by XRD. The remarkable stability has allowed us to test the catalytic activity of gallophosphates for the aerobic oxidation of alkylaromatics with notable good results. Our report reopens the interest for gallophosphates in heterogeneous catalysis. (C) 2010 Elsevier Inc. All rights reserved.

Effects of Charge Location on the Absorptions and Lifetimes of Protonated Tyrosine Peptides in Vacuo

Nearby charges affect the electronic energy levels of chromophores, with the extent of the effect being determined by the magnitude of the charge and degree of charge-chromophore separation. The molecular configuration dictates the charge chromophore distance. Hence, in this study, we aim to assess how the location of the charge influences the absorption of a set of model protonated and diprotonated peptide ions, and whether spectral differences are large enough to be identified. The studied ions were the dipeptide YK, the tripeptide KYK (Y = tyrosine; K = lysine) and their complexes with 18-crown-6-ether (CE). The CE targets the ammonium group by forming internal ionic hydrogen bonds and limits the folding of the peptide. In the tripeptide, the distance between the chromophore and the backbone ammonium is enlarged relative to that in the dipeptide. Experiments were performed in an electrostatic ion storage ring using a tunable laser system, and action spectra based on lifetime measurements were obtained in the range from 210 to 310 nm. The spectra are all quite similar though there seems to be some changes in the absorption band between 210 and 250 nm, while in the lower energy band all ions had a maximum absorption at similar to 275 nm. Lifetimes after photoexcitation were found to shorten upon protonation and lengthen upon CE complexation, in accordance with the increased number of degrees of freedom and an increase in activation energies for dissociation as the mobile proton model is no longer operative.

Simple preparation of positively charged silver nanoparticles for detection of anions by surface-enhanced Raman spectroscopy

Modification of citrate and hydroxylamine reduced Ag colloids with thiocholine bromide, a thiol functionalized quaternary ammonium salt, creates particles where the zeta potential is switched from the normal values of ca. -50 mV to ca. + 50 mV. These colloids are stable but can be aggregated with metal salts in much the same way as the parent colloids. They are excellent SERS substrates for detection of anionic targets since their positive zeta potentials promote adsorption of negatively charged ions. This is important because the vast majority of published SERS studies involve cationic or neutral targets. Moreover, the fact that the modifier is a quaternary ammonium ion means that the negative surface charge is maintained even at alkaline pH. The modified colloids can be used to detect compounds which cannot be detected using conventional negatively-charged citrate or hydroxylamine reduced metal nanoparticles, for example the detection limit was 5.0 x 10(-5) M for perchlorate and

Determination of tartaric acid in wines by FIA with tubular tartrate-selective electrodes

A flow injection analysis (FIA) system comprising a tartrate- (TAT) selective electrode has been developed for determination of tartaric acid in wines. Several electrodes constructed for this purpose had a PVC membrane with a complex of quaternary ammonium and TAT as anion exchanger, a phenol derivative as additive, and a more or less polar mediator solvent. Characterization of the electrodes showed behavior was best for membranes with o-nitrophenyl octyl ether as solvent. On injection of 500 μL into a phosphate buffer carrier (pH = 3.1; ionic strength 10–2 mol/L) flowing at 3 mL/min, the slope was 58.06 ± 0.6 with a lower limit of linear range of 5.0 × 10–4 mol/L TAT and R2 = 0.9989. The interference of several species, e.g. chloride, bromide, iodide, nitrate, gallic acid, tannin, sucrose, glucose, fructose, acetate, and citrate, was evaluated in terms of potentiometric selectivity coefficients. The Hofmeister series was followed for inorganic species and the most interfering organic ion was citrate. When red and white wines were analyzed and the results compared with those from an independent method they were found to be accurate, with relative standard deviations below 5.0%.