Road Design for Future Maintenance : Life-cycle Cost Analyses for Road Barriers

The cost of a road construction over its service life is a function of design, quality of construction as well as maintenance strategies and operations. An optimal life-cycle cost for a road requires evaluations of the above mentioned components. Unfortunately, road designers often neglect a very important aspect, namely, the possibility to perform future maintenance activities. Focus is mainly directed towards other aspects such as investment costs, traffic safety, aesthetic appearance, regional development and environmental effects. This doctoral thesis presents the results of a research project aimed to increase consideration of road maintenance aspects in the planning and design process. The following subgoals were established: Identify the obstacles that prevent adequate consideration of future maintenance during the road planning and design process; and Examine optimisation of life-cycle costs as an approach towards increased efficiency during the road planning and design process. The research project started with a literature review aimed at evaluating the extent to which maintenance aspects are considered during road planning and design as an improvement potential for maintenance efficiency. Efforts made by road authorities to increase efficiency, especially maintenance efficiency, were evaluated. The results indicated that all the evaluated efforts had one thing in common, namely ignorance of the interrelationship between geometrical road design and maintenance as an effective tool to increase maintenance efficiency. Focus has mainly been on improving operating practises and maintenance procedures. This fact might also explain why some efforts to increase maintenance efficiency have been less successful. An investigation was conducted to identify the problems and difficulties, which obstruct due consideration of maintainability during the road planning and design process. A method called “Change Analysis” was used to analyse data collected during interviews with experts in road design and maintenance. The study indicated a complex combination of problems which result in inadequate consideration of maintenance aspects when planning and designing roads. The identified problems were classified into six categories: insufficient consulting, insufficient knowledge, regulations and specifications without consideration of maintenance aspects, insufficient planning and design activities, inadequate organisation and demands from other authorities. Several urgent needs for changes to eliminate these problems were identified. One of the problems identified in the above mentioned study as an obstacle for due consideration of maintenance aspects during road design was the absence of a model for calculating life-cycle costs for roads. Because of this lack of knowledge, the research project focused on implementing a new approach for calculating and analysing life-cycle costs for roads with emphasis on the relationship between road design and road maintainability. Road barriers were chosen as an example. The ambition is to develop this approach to cover other road components at a later stage. A study was conducted to quantify repair rates for barriers and associated repair costs as one of the major maintenance costs for road barriers. A method called “Case Study Research Method” was used to analyse the effect of several factors on barrier repairs costs, such as barrier type, road type, posted speed and seasonal effect. The analyses were based on documented data associated with 1625 repairs conducted in four different geographical regions in Sweden during 2006. A model for calculation of average repair costs per vehicle kilometres was created. Significant differences in the barrier repair costs were found between the studied barrier types. In another study, the injuries associated with road barrier collisions and the corresponding influencing factors were analysed. The analyses in this study were based on documented data from actual barrier collisions between 2005 and 2008 in Sweden. The result was used to calculate the cost for injuries associated with barrier collisions as a part of the socio-economic cost for road barriers. The results showed significant differences in the number of injuries associated with collisions with different barrier types. To calculate and analyse life-cycle costs for road barriers a new approach was developed based on a method called “Activity-based Life-cycle Costing”. By modelling uncertainties, the presented approach gives a possibility to identify and analyse factors crucial for optimising life-cycle costs. The study showed a great potential to increase road maintenance efficiency through road design. It also showed that road components with low investment costs might not be the best choice when including maintenance and socio-economic aspects. The difficulties and problems faced during the collection of data for calculating life-cycle costs for road barriers indicated a great need for improving current data collecting and archiving procedures. The research focused on Swedish road planning and design. However, the conclusions can be applied to other Nordic countries, where weather conditions and road design practices are similar. The general methodological approaches used in this research project may be applied also to other studies.

Applicazione della metodologia Life Cycle Assessment al Passito di Pantelleria

Il presente studio riguarda l’applicazione della metodologia Life Cycle Assessment (LCA) ad una bottiglia di Passito di Pantelleria, prodotta dall’Azienda vitivinicola “Donnafugata” localizzata nel comune di Marsala in Sicilia. L’obiettivo di tale studio consiste nel quantificare e valutare le prestazioni energetico-ambientali derivanti dall’intero ciclo di vita del processo produttivo, nonché le fasi di produzione che presentano il maggiore impatto. Lo studio è stato ulteriormente approfondito effettuando una comparazione tra la produzione della singola bottiglia di Passito nei diversi anni 2007, 2008 e 2009 con lo scopo di determinare quali tra questi risulta avere il maggiore impatto ambientale. Gli impatti ambientali di un’Azienda vitivinicola risultano avere la loro particolare importanza in quanto la produzione di vino è un processo di natura complessa. Di conseguenza tali impatti possono compromettere le componenti fondamentali del processo produttivo, a partire dalle uve coltivate in vigna fino ad arrivare in cantina, dove avviene la trasformazione dell’uva in mosto e la successiva fase di vinificazione che determina il prodotto finale messo in commercio. Proprio attraverso il fluire delle seguenti fasi di trasformazione, in che misura queste consumano energia e producono emissioni? È importante sottolineare che lo studio del ciclo di vita di un prodotto può essere considerato come un supporto fondamentale allo sviluppo di schemi di etichettatura ambientale attraverso i quali è possibile indirizzare il consumatore finale verso beni più rispettosi dell’ambiente e fornire informazioni chiare e trasparenti sulle prestazioni ambientali del prodotto stesso. Allo stesso tempo tale strumento può essere adoperato dall’azienda per fornire garanzia delle credenziali ambientali del prodotto acquisendo così un vantaggio competitivo rispetto alle aziende concorrenti. Infatti, nell’ambito delle politiche comunitarie di prodotto, una delle applicazioni più significative della valutazione del ciclo di vita si ha nella dichiarazione ambientale di prodotto o EPD (Environmental Product Declaration). L’EPD è uno schema di certificazione volontaria che rappresenta un marchio di qualità ecologica per i prodotti, permettendo di comunicare informazioni oggettive, confrontabili e credibili relative alla prestazione ambientale degli stessi. Per essere convalidabili, le prestazioni ambientali presenti nelle EPD devono rispettare i requisiti stabiliti dal PCR- Product Category Rules, un documento nel quale sono presenti le regole per lo studio di una certa categoria di prodotto. Il presente lavoro può essere suddiviso in cinque step successivi. Il primo prevede la descrizione della metodologia LCA, adottata per la quantificazione dell’impatto ambientale, analizzandone singolarmente le quattro fasi principali che la caratterizzano; il secondo presenta la descrizione dell’Azienda vitivinicola e del Passito di Pantelleria, oggetto della valutazione, mettendo in evidenza anche le particolarità ambientali del territorio Pantesco in cui il prodotto prende vita; il terzo fornisce una descrizione delle caratteristiche principali dello strumento applicativo utilizzato per l’analisi, SimaPro nella versione 7.3; il quarto descrive le diverse attività di lavorazione svolte nel complesso processo di produzione della bottiglia di Passito, focalizzando l’attenzione sui componenti primari dell’oggetto di valutazione ed il quinto riguarda la descrizione dell’analisi LCA applicata alla singola bottiglia di Passito.

Flat roofs renovation: a life cycle approach for environmental impact assessment and economic effectiveness

The high energy consumption caused by the building sector and the continuous growth and ageing of the existing housing stock show the importance of housing renovation to improve the quality of the environment. This research compares the environmental performance of flat roof systems (insulation, roofing membrane and covering layer) using Life Cycle Assessment (LCA). The aim is to give indications on how to improve the environmental performance of housing. This research uses a reference building located in the Netherlands and considers environmental impacts related to materials, energy consumption for heating and maintenance activities. It indicates impact scores for each material taking into account interconnections between the layers and between the different parts of the life cycle. It compares the environmental and economic performances of PV panels and of different materials and thermal resistance values for the insulation. These comparisons show that PV panels are convenient from an environmental and economic point of view. The same is true for the insulation layer, especially for materials as PIR (polyisocyanurate) and EPS (expanded polystyrene). It shows that energy consumption for heating causes a larger share of impact scores than production of the materials and maintenance activities. The insulation also causes larger impact scores comparing to roofing membrane and covering layer. The results show which materials are preferable for flat roof renovation and what causes the largest shares of impact. This gives indication to the roofers and to other stakeholders about how to reduce the environmental impact of the existing housing stock.

LIFE CYCLE ASSESSMENT OF BIOFUEL PRODUCED FROM ALGAE

Algae are considered a promising source of biofuels in the future. However, the environmental impact of algae-based fuel has high variability in previous LCA studies due to lack of accurate data from researchers and industry. The National Alliance for Advanced Biofuels and Bioproducts (NAABB) project was designed to produce and evaluate new technologies that can be implemented by the algal biofuel industry and establish the overall process sustainability. The MTU research group within NAABB worked on the environmental sustainability part of the consortium with UOP-Honeywell and with the University of Arizona (Dr. Paul Blowers). Several life cycle analysis (LCA) models were developed within the GREET Model and SimaPro 7.3 software to quantitatively assess the environment viability and sustainability of algal fuel processes. The baseline GREET Harmonized algae life cycle was expanded and replicated in SimaPro software, important differences in emission factors between GREET/E-Grid database and SimaPro/Ecoinvent database were compared, and adjustments were made to the SimaPro analyses. The results indicated that in most cases SimaPro has a higher emission penalty for inputs of electricity, chemicals, and other materials to the algae biofuels life cycle. A system-wide model of algae life cycle was made starting with preliminary data from the literature, and then progressed to detailed analyses based on inputs from all NAABB research areas, and finally several important scenarios in the algae life cycle were investigated as variations to the baseline scenario. Scenarios include conversion to jet fuel instead of biodiesel or renewable diesel, impacts of infrastructure for algae cultivation, co-product allocation methodology, and different usage of lipid-extracted algae (LEA). The infrastructure impact of algae cultivation is minimal compared to the overall life cycle. However, in the scenarios investigating LEA usage for animal feed instead of internal recycling for energy use and nutrient recovery the results reflect the high potential variability in LCA results. Calculated life cycle GHG values for biofuel production scenarios where LEA is used as animal feed ranged from a 55% reduction to 127% increase compared to the GREET baseline scenario depending on the choice of feed meal. Different allocation methods also affect LCA results significantly. Four novel harvesting technologies and two extraction technologies provided by the NAABB internal report have been analysis using SimaPro LCA software. The results indicated that a combination of acoustic extraction and acoustic harvesting technologies show the most promising result of all combinations to optimize the extraction of algae oil from algae. These scenario evaluations provide important insights for consideration when planning for the future of an algae-based biofuel industry.

THE USE OF LIFE-CYCLE ANALYSIS TO REDUCE THE ENVIRONMENTAL IMPACT OF MATERIALS IN MANUFACTURING

This thesis is composed of three life-cycle analysis (LCA) studies of manufacturing to determine cumulative energy demand (CED) and greenhouse gas emissions (GHG). The methods proposed could reduce the environmental impact by reducing the CED in three manufacturing processes. First, industrial symbiosis is proposed and a LCA is performed on both conventional 1 GW-scaled hydrogenated amorphous silicon (a-Si:H)-based single junction and a-Si:H/microcrystalline-Si:H tandem cell solar PV manufacturing plants and such plants coupled to silane recycling plants. Using a recycling process that results in a silane loss of only 17 versus 85 percent, this results in a CED savings of 81,700 GJ and 290,000 GJ per year for single and tandem junction plants, respectively. This recycling process reduces the cost of raw silane by 68 percent, or approximately $22.6 and $79 million per year for a single and tandem 1 GW PV production facility, respectively. The results show environmental benefits of silane recycling centered around a-Si:H-based PV manufacturing plants. Second, an open-source self-replicating rapid prototype or 3-D printer, the RepRap, has the potential to reduce the environmental impact of manufacturing of polymer-based products, using distributed manufacturing paradigm, which is further minimized by the use of PV and improvements in PV manufacturing. Using 3-D printers for manufacturing provides the ability to ultra-customize products and to change fill composition, which increases material efficiency. An LCA was performed on three polymer-based products to determine the CED and GHG from conventional large-scale production and are compared to experimental measurements on a RepRap producing identical products with ABS and PLA. The results of this LCA study indicate that the CED of manufacturing polymer products can possibly be reduced using distributed manufacturing with existing 3-D printers under 89% fill and reduced even further with a solar photovoltaic system. The results indicate that the ability of RepRaps to vary fill has the potential to diminish environmental impact on many products. Third, one additional way to improve the environmental performance of this distributed manufacturing system is to create the polymer filament feedstock for 3-D printers using post-consumer plastic bottles. An LCA was performed on the recycling of high density polyethylene (HDPE) using the RecycleBot. The results of the LCA showed that distributed recycling has a lower CED than the best-case scenario used for centralized recycling. If this process is applied to the HDPE currently recycled in the U.S., more than 100 million MJ of energy could be conserved per annum along with significant reductions in GHG. This presents a novel path to a future of distributed manufacturing suited for both the developed and developing world with reduced environmental impact. From improving manufacturing in the photovoltaic industry with the use of recycling to recycling and manufacturing plastic products within our own homes, each step reduces the impact on the environment. The three coupled projects presented here show a clear potential to reduce the environmental impact of manufacturing and other processes by implementing complimenting systems, which have environmental benefits of their own in order to achieve a compounding effect of reduced CED and GHG.

Quantity of CO2 Emissions in the Life Cycle of a Highway Infrastructure

There is strong evidence to indicate that carbon dioxide and other greenhouse gases are accumulating at unprecedented concentrations in out atmosphere contributing to global climate change. Evidence is equally strong that human activities, mainly the burning of fossil fuels, are driving force in this process (IPCC 2007). While different industries contribute varying amounts to total anthropogenic greenhouse gases, it is incumbent upon each to understand its contribution and search for sensible ways to reduce overall greenhouse gas production. The aim of this paper is the development of a methodology to determine the amount of CO2 emissions of a highway, allowing providing solutions that can improve the energy footprint and reduce its emissions

Quantity of CO2 Emissions in the Life Cycle of a Highway Infrastructure.

The complexity of climate change and its evolution during the last few years has a positive impact on new developments and approaches to reduce the emissions of CO2. Looking for a methodology to evaluate the sustainability of a roadway, a tool has been developed. Life Cycle Assessment (LCA) is being accepted by the road industry to measure and evaluate the environmental impacts of an infrastructure, as the energy consumption and carbon footprint. This paper describes the methodology to calculate the CO2 emissions associated with the energy embodied on a roadway along its life cycle, including construction, operations and demolition. It will assist to find solutions to improve the energy footprint and reduce the amount of CO2 emissions. Details are provided of both, the methodology and the data acquisition. This paper is an application of the methodology to the Spanish highways, using a local database. Two case studies and a practical example are studied to show the model as a decision support for sustainable construction in the road industry.

Is building renovation truly sustainable? The need for applying a multi-criteria assessment through life cycle approach

The aim of the present research is to characterise the international scene in the field of building refurbishment, by thoroughly reviewing the literature relating to building renovation and systematising the results according to the different aspects considered by the authors. Even though there is certain consensus with respect to the criteria for the selection of energy efficiency measures, the assessment criteria differ broadly and widely. The present work highlights the lack of consensus on the assessment criteria and the need of harmonization. A holistic view is required in order to identify the most sustainable strategies in each particular case, considering social, environmental and economic impacts from a life cycle perspective.

Methodology proposal for the life cycle sustainability assessment applied to retrofitting in a local context

In the European context of upgrading the housing stock energy performance, multiple barriers hinder the wide uptake of sustainable retrofitting practices. Moreover, some of these may imply negative effects often disregarded. Policy makers need to identify how to increase and improve retrofitting practices from the comprehensive point of view of sustainability. None of the existing assessment tools addresses all the issues relevant for sustainable development in a local situation from a life cycle perspective. Life cycle sustainability assessment methodology, or LCSA, analyzes environmental and socioeconomic impacts. The environmental part is quite developed, but the socioeconomic aspect is still challenging. This work proposes socioeconomic criteria to be included in a LCSA to assess retrofitting works in the specific context of Brussels-Capital Region. LCSA feasibility and challenging methodology aspects are discussed.

Life Cycle Assessment as a tool to promote sustainable Thermowood boards: a Portuguese case study

The present work aims to develop the Life Cycle Assessment study of thermo-modified Atlanticwood® pine boards based on real data provided by Santos & Santos Madeiras company. Atlanticwood® pine boards are used mainly for exterior decking and cladding facades of buildings. The LCA study is elaborated based on ISO 14040/44 standard and Product Category Rules for preparing an environmental product declaration for Construction Products and Construction Services. The inventory analysis and, subsequently, the impact analysis have been performed using the LCA software SimaPro8.0.4. The method chosen for impact assessment was EPD (2013) V1.01. The results show that more than ¾ of ‘Acidification’, ‘Eutrophication’, ‘Global warming’ and ‘Abiotic depletion’ caused by 1 m3 of Atlanticwood® pine boards production is due to energy consumption (electricity + gas + biomass). This was to be expected since the treatment is based on heat production and no chemicals are added during the heat treatment process.

Life-cycle aspects of poverty among older women /

"April 1997."

Life Cycle Assessment (LCA) Applied to the Design of an Innovative Drying Process for Sewage Sludge

Most adverse environmental impacts result from design decisions made long before manufacturing or usage. In order to prevent this situation, several authors have proposed the application of life cycle assessment (LCA) at the very first phases of the design of a process, a product or a service. The study in this paper presents an innovative thermal drying process for sewage sludge called fry-drying, in which dewatered sludge is directly contacted in the dryer with hot recycled cooking oils (RCO) as the heat medium. Considering the practical difficulties for the disposal of these two wastes, fry-drying presents a potentially convenient method for their combined elimination by incineration of the final fry-dried sludge. An analytical comparison between a conventional drying process and the new proposed fry-drying process is reported, with reference to some environmental impact categories. The results of this study, applied at the earliest stages of the design of the process, assist evaluation of the feasibility of such system compared to a current disposal process for the drying and incineration of sewage sludge.