An AC voltage regulator with high-power-factor, and control using a FPGA device

This paper presents the analysis, design, simulation, and experimental results for a high frequency high Power-Factor (PF) AC (Alternate Current) voltage regulator, using a Sepic converter as power stage. The control technique employed to impose a sinusoidal input current waveform, with low Total Harmonic Distortion (THD), is the sinusoidal variable hysteresis control. The control technique was implemented in a FPGA (Field Programmable Gate Array) device, using a Hardware Description Language (VHDL). Through the use of the proposed control technique, the AC voltage regulator performs active power-factor correction, and low THD in the input current, for linear and non-linear loads, satisfying the requirements of the EEC61000-3-2 standards. Experimental results from an example prototype, designed for 300W of nominal output power, 50kHz (switching frequency), and 127Vrms of nominal input and output voltages, are presented in order to validate the proposed AC regulator. © 2005 IEEE.

Comportamento de forrageamento do pernilongo-de-costas-brancas, Himantopus melanurus (Vieillot, 1817) (Aves: Recurvirostridae) em Santa Gertrudes, SP, Brasil

The foraging behavior of two White-backed stilts (Himantopus melanurus) was studied in a lake at the municipality of Santa Gertrudes, state of São Paulo, Brazil. The foraging strategies observed were classified in two categories: pluging (65.8% of total maneuvers) and pecking (34.3%). Only in 26.8% of the foraging maneuvers the individuals captured preys (72.9% by plunging and 27.1% by pecking). When comparing both strategies, plunging was successful 29.7% of the times, but pecking only 21.2%. At the study site, individuals foraged only up to 20 m away from the lake margin. The foraging area exploited by the White-backed stilts was estimated in about 720 m 2. Foraging activities lasted since before sunrise until after sunset. © 2006 Instituto de Ciências Biológicas - UFMG.

Short-term planning of electric power distribution networks using multiobjective genetic algorithim

The high active and reactive power level demanded by the distribution systems, the growth of consuming centers, and the long lines of the distribution systems result in voltage variations in the busses compromising the quality of energy supplied. To ensure the energy quality supplied in the distribution system short-term planning, some devices and actions are used to implement an effective control of voltage, reactive power, and power factor of the network. Among these devices and actions are the voltage regulators (VRs) and capacitor banks (CBs), as well as exchanging the conductors sizes of distribution lines. This paper presents a methodology based on the Non-Dominated Sorting Genetic Algorithm (NSGA-II) for optimized allocation of VRs, CBs, and exchange of conductors in radial distribution systems. The Multiobjective Genetic Algorithm (MGA) is aided by an inference process developed using fuzzy logic, which applies specialized knowledge to achieve the reduction of the search space for the allocation of CBs and VRs.

Estudo da geometria e cinemática das rochas sedimentares arqueanas da mina do Igarapé do Azul – Carajás-PA

Mina de Manganês do Igarapé Azul posiciona-se geologicamente no interior do feixe da Falha Carajás, na porção central do Sistema Transcorrente de Carajás. O depósito do Manganês do Azul relaciona-se a rochas sedimentares pelíticas do Membro Azul, na base da Formação Águas Claras (Arqueano), em contato discordante, acima do Grupo Grão Pará (Nogueira et al, 1995). Três frentes de lavra a céu aberto estão atualmente em andamento na área: (1) Mina Principal (Mina 1), (2) Mina 2 e (3) Mina 3. Nestes locais encontram-se excelentes afloramentos de siltitos intercalados com argilitos e arenitos finos, intercalados com níveis manganesíferos. Essas rochas estão organizadas em conjuntos de dobras e falhas normais e inversas sob deformação heterogênea, particionada em diferentes escalas. As seções geológicas realizadas nas frentes de lavra mostram a predominância de siltitos intercalados com argilitos em contato com rochas pelíticas manganesíferas e minério (bióxido de Mn). Nessas rochas são comuns estruturas primárias tipo hummocky, estratificações cruzadas, e laminações plano-paralelas. O acamamento centimétrico a métrico (em média de 30 a 50 cm ) representa a principal estrutura primária, usada como marcador de deformação, observada nas rochas. A Mina do Igarapé Azul encontra-se dividida em dois blocos, separados por falha normal com rejeito de até dezenas de metros, com o bloco norte alto em relação ao bloco sul. O bloco sul encontra-se pouco deformado, apresentado uma regularidade no acamamento que mergulha com ângulos suaves para sul, colocando a camada de minério sucessivamente em níveis mais profundos na direção S. No bloco norte o acamamento apresenta um comportamento heterogêneo. A deformação é mais expressiva nessa região, estando o nível de minério deformado por dobras e falhas inversas. Além da cinemática vertical, as falhas apresentam deslocamento conjugado destral dando a essas feições um caráter oblíquo. Essa região pode ser definida como um corredor de deformação. O corredor observado no bloco norte, de acordo com os domínios principais separados pelas falhas anteriormente descritas, possui orientação NW-SE, com aproximadamente um quilômetro de extensão, sendo caracterizado por dobras assimétricas curvilineares com eixos de mergulhos suaves (10° a 25°) para NW e SE. Essas dobras são seccionadas por falhas normais sinuosas NW-SE e/ou E-W, com baixo ângulo de mergulho (em torno de 10° a 30°), subordinadas a transcorrências destrais, gerando em escala de detalhes feições como drag folds. Observam-se ainda falhas inversas retas e/ou sinuosas NW-SE e zonas de falhas sub-verticalizadas WNW -ESE. As dobras individuais nesta área são estruturas do tipo reversas, flexurais e com geometria en echelon com orientação semelhante às dobras curvilineares: eixos com baixo ângulo de mergulho (10° a 25°) e caimento para SE. O conjunto de feições anteriormente descrito desenha, em escala quilométrica, um antiforme aberto, provavelmente resultante da acomodação do acamamento em resposta a deformação dessas falhas. O paralelismo entre feições observadas na área da Mina do Igarapé Azul e os lineamentos maiores que desenham a Falha Carajás em planta sugere uma relação com dois importantes episódios deformacionais ocorridos durante a história tectônica da Falha Carajás. As falhas normais associadas a componente direcional destral, de maior expressividade da área da mina, estariam relacionadas ao episódio de transtensão destral responsável pela instalação da Falha Carajás anterior a 2.6 Ga (Pinheiro, 1997). As dobras, as falhas de cavalgamento e as zonas de falhas sub-verticalizadas estariam relacionados a deformações sob regime de transpressão sinistral, um segundo evento atuante na região, responsável pela reativação e inversão da maioria das estruturas próximas à zona da Falha Carajás (Pinheiro, 1997; Pinheiro & Holdsworth, 2000; Lima, 2002).

Estudo e analise dos sistemas de proteção em subestações automatizadas de energia elétrica

Electrical energy is present in the lives of all people and is extremely important that it be delivered to end users with plenty of quality, safety and low costs. The electric power substations are responsible for transmission and distribution of electricity generating sources to consumers, and with technological advances and the subsequent automation of same, the electricity began to be delivered with greater continuity and reliability. Protection systems in substations are largely responsible for making the electricity reaches the final consumer with quality, since their function is to prevent the spread of any type of failure occurred at any point of transmission to the load centers. These systems consist primarily by the current transformers and potential, by the protective relays and circuit breakers and switchgear. The processors send the necessary data to the relays and, if those detect any abnormality in the system, operate the opening command of the branch circuit breakers to isolate where the fault. Therefore, it is essential to better understand the operation of such equipment, as well as the overall system. This work aims to study the main substation equipment, current transformers and potential and, especially, protection relays, in order to obtain the advantages that automated systems can provide

Anteprojeto de um sistema digital de proteção e controle aplicado em uma subestação elétrica industrial

With the growth of the demand on electric energy in the last decades, the urban distribution and transmission systems have experienced a bigger necessity to improve on the substations, the automation procedures and techniques on the operation maneuvers of such systems, in a sense that better attends the quality levels, availability, continuity and operational reliability. In this way, the objective of the present paper is to perform a study of protection and control on an electrical industrial system involving the procedures of digitizing and maneuvers automatism utilizing operational techniques and other pertinent information used in a typical high-voltage Industrial Electrical System. Analysis were made on short-circuits to specify the main components of the 138 [kV] substation, in addition, there were used digital MiCOM relays to make the protection of the present elements. With that, a program was developed to allow the user to monitor the condition of circuit-breakers through a supervision screen being able to simulate some kinds of faults, as well as observing the characteristics of each device. This way, the importance of having a fast and reliable system that ensures the equipment’s protection and the industrial process continuity due to faults on the electrical system is noticeable. It’s important to highlight that all this digitizing was mainly favored by the development of digital technology on the last years, mainly on microelectronics, also with the appearance of supervision gadgets allowing the development of complex systems in supervision and electric energy control

Sociedade, tecnologias e educação: as tecnologias da informação e comunicação e o pensar da sociedade concreta

The information society is increasingly incorporating the immense volume of content available on the net. Access by electronic devices and the resulting ease of mobility and portability feed discussions on actual capacity of appropriation of this knowledge that circulates through cyberspace. Address and discuss the possibilities of educating across the network, therefore, gains more and more importance. On models of educational quality well developed – as is the case in Finland, for example-, Brazilian education is, year after year, failing in international marathons to achieve below average indexes required. Creates a field of analysis, in which this article arises, in the quest to understand more deeply the opportunity of use of Information and communication technologies (ICT) for a quality education, plunging by cultural issues that fall in the construction of objective conditions offered to students. This is an effort in understanding the historical factors that limit efforts to offering a quality education in Brazil.

Desenvolvimento de um sistema de proteção e metodologia para localização de faltas em sistemas de distribuição

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Geologia do depósito de ouro de C1-Santaluz no greenstone belt do rio Itapicuru, Brasil

Pós-graduação em Geociências e Meio Ambiente - IGCE

Ordovician klippen structures of the Sierra de Umango: New insights on Tectonic evolution of the Western Sierras Pampeanas, Argentina

The basement rock of the Pampean flat-slab (Sierras Pampeanas) in the Central Andes was uplifted and rotated in the Cenozoic era. The Western Sierras Pampeanas are characterised by meta-igneous rocks of Grenvillian Mesoproterozoic age and metasedimentary units metamorphosed in the Ordovician period. These rocks, known as the northern Cuyania composite terrane, were derived from Laurentia and accreted toward Western Gondwana during the Early Paleozoic. The Sierra de Umango is the westernmost range of the Western Sierras Pampeanas.This range is bounded by the Devonian sedimentary rocks of the Precordillera on the western side and Tertiary rocks from the Sierra de Maz and Sierra del Espinal on the eastern side and contains igneous and sedimentary rocks outcroppings from the Famatina System on the far eastern side. The Sierra de Umango evolved during a period of polyphase tectonic activity, including an Ordovician collisional event, a Devonian compressional deformation, Late Paleozoic and Mesozoic extensional faulting and sedimentation (Paganzo and Ischigualasto basins) and compressional deformation of the Andean foreland during the Cenozoic. A Nappe System and an important shear zone, La Puntilla-La Falda Shear Zone (PFSZ), characterise the Ordovician collisional event, which was related to the accretion of Cuyania Terrane to the proto-Andean margin of Gondwana. Three continuous deformational phases are recognised for this event: the D1 phase is distinguished by relics of 51 preserved as internal foliation within interkinematic staurolite por-phyroblasts and likely represents the progressive metamorphic stage; the D2 phase exhibits P-T conditions close to the metamorphic peak that were recorded in an 52 transposition or a mylonitic foliation and determine the main structure of Umango; and the D3 phase is described as a set of tight to recumbent folds with S3 axial plane foliation, often related to thrust faults, indicating the retrogressive metamorphic stage. The Nappe System shows a top-to-the S/SW sense direction of movement, and the PFSZ served as a right lateral ramp in the exhumation process. This structural pattern is indicative of an oblique collision, with the Cuyania Terrane subducting under the proto-Andean margin of Gondwana in the NE direction. This continental subduction and exhumation lasted at least 30 million years, nearly the entire Ordovician period, and produced metamorphic conditions of upper amphibolite-to-granulite facies in medium- to high-pressure regimes. At least two later events deformed the earlier structures: D4 and D5 deformational phases. The D4 deformational phase corresponds to upright folding, with wavelengths of approximately 10 km and a general N-S orientation. These folds modified the S2 surface in an approximately cylindrical manner and are associated with exposed, discrete shear zones in the Silurian Guandacolinos Granite. The cylindrical pattern and subhorizontal axis of the D4 folds indicates that the S2 surface was originally flat-lying. The D4 folds are responsible for preserving the basement unit Juchi Orthogneiss synformal klippen. This deformation corresponds to the Chanica Tectonic during the interval between the Devonian and Carboniferous periods. The D5 deformational phase comprehends cuspate-lobate shaped open plunging folds with E W high-angle axes (D5 folds) and sub-vertical spaced cleavage. The D5 folds and related spaced cleavage deformed the previous structures and could be associated with uplifting during the Andean Cycle. (C) 2012 Elsevier Ltd. All rights reserved.

Magnetic fabrics and their relationship with the emplacement of the Piracaia pluton, SE Brazil

Magnetic fabric and rock-magnetism studies were performed on the four units of the 578 +/- 3-Ma-old Piracaia pluton (NW of Sao Paulo State, southern Brazil). This intrusion is roughly elliptical (similar to 32 km(2)), composed of (i) coarse-grained monzodiorite (MZD-c), (ii) fine-grained monzodiorite (MZD-f), which is predominant in the pluton, (iii) monzonite heterogeneous (MZN-het), and (iv) quartz syenite (Qz-Sy). Magnetic fabrics were determined by applying both anisotropy of low-field magnetic susceptibility (AMS) and anisotropy of anhysteretic remanent magnetization (AARM). The two fabrics are coaxial. The parallelism between AMS and AARM tensors excludes the presence of a single domain (SD) effect on the AMS fabric of the units. Several rock-magnetism experiments performed in one specimen from each sampled units show that for all of them, the magnetic susceptibility and magnetic fabrics are carried by magnetite grains, which was also observed in the thin sections. Foliations and lineations in the units were successfully determined by applying magnetic methods. Most of the magnetic foliations are steeply dipping or vertical in all units and are roughly parallel to the foliation measured in the field and in the country rocks. In contrast, the magnetic lineations present mostly low plunges for the whole pluton. However, for eight sites, they are steep up to vertical. Thin-section analyses show that rocks from the Piracaia pluton were affected by the regional strain during and after emplacement since magmatic foliation evolves to solid-state fabric in the north of the pluton, indicating that magnetic fabrics in this area of the pluton are related to this strain. Otherwise, the lack of solid-state deformation at outcrop scale and in thin sections precludes deformation in the SW of the pluton. This evidence allows us to interpret the observed magnetic fabrics as primary in origin (magmatic) acquired when the rocks were solidified as a result of magma flow, in which steeply plunging magnetic lineation suggests that a feeder zone could underlie this area.

Detection of partial discharges at field in SF6 insulated equipments

This paper presents the results of research aiming to develop partial discharge detection techniques in high voltage equipment, at substation environment. Measurements of high frequency components of leakage current, at equipments' grounding conductor, were performed. This procedure was performed with the equipment energized and without disconnecting it from the system. The partial discharge generated current pulse is picked up by a high frequency CT, and is detected by an oscilloscope. The partial discharge identification was made considering previously obtained laboratory results, where partial discharges were characterized by means of its time domain signatures. This paper focuses measurements in SF6 circuit breakers. Encouraging results were obtained, showing the feasibility of detecting partial discharges in energized equipment in the laboratory and in the field, in a substation environment, using this method.

A STUDY ON THE FEASIBILITY OF UNIVERSAL CHIP CONTROL IN MACHINING

A novel solution to the long standing issue of chip entanglement and breakage in metal cutting is presented in this dissertation. Through this work, an attempt is made to achieve universal chip control in machining by using chip guidance and subsequent breakage by backward bending (tensile loading of the chip's rough top surface) to effectively control long continuous chips into small segments. One big limitation of using chip breaker geometries in disposable carbide inserts is that the application range is limited to a narrow band depending on cutting conditions. Even within a recommended operating range, chip breakers do not function effectively as designed due to the inherent variations of the cutting process. Moreover, for a particular process, matching the chip breaker geometry with the right cutting conditions to achieve effective chip control is a very iterative process. The existence of a large variety of proprietary chip breaker designs further exacerbates the problem of easily implementing a robust and comprehensive chip control technique. To address the need for a robust and universal chip control technique, a new method is proposed in this work. By using a single tool top form geometry coupled with a tooling system for inducing chip breaking by backward bending, the proposed method achieves comprehensive chip control over a wide range of cutting conditions. A geometry based model is developed to predict a variable edge inclination angle that guides the chip flow to a predetermined target location. Chip kinematics for the new tool geometry is examined via photographic evidence from experimental cutting trials. Both qualitative and quantitative methods are used to characterize the chip kinematics. Results from the chip characterization studies indicate that the chip flow and final form show a remarkable consistency across multiple levels of workpiece and tool configurations as well as cutting conditions. A new tooling system is then designed to comprehensively break the chip by backward bending. Test results with the new tooling system prove that by utilizing the chip guidance and backward bending mechanism, long continuous chips can be more consistently broken into smaller segments that are generally deemed acceptable or good chips. It is found that the proposed tool can be applied effectively over a wider range of cutting conditions than present chip breakers thus taking possibly the first step towards achieving universal chip control in machining.