THE CHARPY IMPACT FRACTURE-BEHAVIOR OF PHENOLPHTHALEIN POLYETHER KETONE

The Charpy impact fracture behavior of notched specimens of phenolphthalein poly(ether ketone) (PEK-C) has been studied over a range of temperature using a JJ-20 Model instrumented impact tester. For PEK-C, there exist two temperature regions which distinguish the fracture mechanism, and the brittle fracture was preferentially governed by slip or shear bands at relatively high temperatures, but by crazes at low temperatures. The temperature dependence of the ductility index (DI) shows similar peaks to the tan delta loss. (C) 1995 John Wiley and Sons, Inc.

MECHANICAL-PROPERTIES OF PHENOLPHTHALEIN POLYETHER KETONE - YIELD STRESS, YOUNGS MODULUS, AND FRACTURE-TOUGHNESS

A series of tensile and three-point bending studies was conducted at various temperatures and loading rates using phenolphthalein polyether ketone (PEK-C). Yield stress, Young's modulus, fracture toughness, and crack opening displacement data were obtained for various conditions. In general, both yield stress and Young's modulus increase with decreasing temperature. However, the relationships between fracture toughness, loading rate, and temperature are very complex. This behavior is due to the simultaneous intersection of viscoelasticity and localized plastic deformation. The increased yield stress is the main factor contributing to the reduction in fracture toughness and crack opening displacement. The relationship between fracture toughness and yield stress are discussed. (C) 1995 John Wiley and Sons, Inc.

THE FRACTURE-BEHAVIOR OF PHENOLPHTHALEIN POLYETHER ETHER KETONE AT ELEVATED-TEMPERATURE FOR LONG TERMS

The fracture behavior of phenolphthalein polyether-ether ketone (PEK-C) affected by physical aging at 200 degrees C was studied by tensile experiments, scanning electron microscopy, and differential scanning calorimetry observations. The ductile-brittle fracture transition (DBT) caused by physical aging can be considered as a competition between fracture mechanisms of crazing and shear yielding. The aging time required for the DBT is found to be around 400 h, based on the morphological studies and tensile experiments. The shear yielding component of the mechanical deformation could erase the aging effect, thus a deaging phenomenon occurs. We found that the deaging phenomenon has an intrinsic relationship with the extent of aging in the specimen and as a result of the fracture behavior. (C) 1995 John Wiley and Sons, Inc.

YIELD BEHAVIOR AND VISCOELASTIC INTERPRETATION BY ACTIVATION VOLUMEN OF PHENOLPHTHALEIN POLYETHER KETONE

Phenolphthalein polyether ketone (PEK-C) exhibits a marked tensile yield behaviour. The yield stress depends on strain rate and the activation volume V could be evaluated from the data of the yield stress. From the creep and stress relaxation behaviour,

TENSILE YIELD IN PHENOLPHTHALEIN POLYETHER KETONE

Uniaxial tension tests to the yield point were performed on phenolphthalein polyether ketone (PEK-C) from room temperature to near the glass transition temperature (T-g) at a constant rate of 0.02 min(-1). At room temperature, some measurements were also

J-INTEGRAL STUDIES OF CRACK INITIATION AND CRACK TIP-BLUNTING OF PHENOLPHTHALEIN POLYETHER KETONE

The J-integral is applied to characterize the fracture initiation of phenolphthalein polyether ketone (PEK-C) for which the concepts of linear elastic fracture mechanics (LEFM) are inapplicable at high temperatures for reasonably-sized specimens due to ex

FRACTURE-TOUGHNESS AND MORPHOLOGY OF PHENOLPHTHALEIN POLY(ETHER SULFONE) THERMOTROPIC LIQUID-CRYSTALLINE POLYMER BLENDS

Blends of a new phenolphthalein poly (ether sulfone) (PES-C) and a thermotropic liquid crystalline polymer (LCP) were prepared by melt-blending in a twin-screw extruder. Rheological properties, fracture toughness, K(IC), and morphology of the blends were

PHASE-BEHAVIOR IN EPOXY-RESIN CONTAINING PHENOLPHTHALEIN POLY(ETHER ETHER SULFONE)

Phenolphthalein poly(ether ether sulphone) (PES-C) was found to be miscible with uncured bisphenol-A-type epoxy resin, i.e. diglycidyl ether of bisphenol A (DGEBA), as shown by the existence of a single glass transition temperature within the whole composition range. Miscibility between PES-C and DGEBA is considered to be due mainly to the entropy contribution. However, dynamic mechanical analysis (d.m.a.) and scanning electron microscopy (SEM) studies revealed that PES-C exhibits different miscibility with four cured epoxy resins (ER). The overall compatibility and the resulting morphology of the cured blends are dependent on the choice of cure agent. For the blends cured with amines (4,4'-diaminodiphenylmethane (DDM) and 4,4'-diaminodiphenylsulphone (DDS)), no phase separation occurs as indicated by either d.m.a. or SEM. However, for the blends cured with anhydrides (maleic anhydride (MA) and phthalic anhydride (PA)), both d.m.a. and SEM clearly show evidence of phase separation. SEM study shows that the two phases interact well in the MA-cured blend while the interface between the phases in the PA-cured blend is poorly bonded. The differences in the overall compatibility and the resulting morphology between the amine-cured and anhydride-cured systems have been discussed from the points of view of both thermodynamics and kinetics.

MISCIBILITY OF POLY(HYDROXYETHER OF PHENOLPHTHALEIN) WITH POLY(ETHER SULFONE)

Blends of poly(hydroxyether of phenolphthalein) (PHP) with poly(ether sulphone) (PES) were prepared by casting from a common solvent; they were found to be miscible and show a single, composition-dependent glass transition temperature. All the PHP/PES blends exhibited lower critical solution temperature behaviour, i.e. phase separation occurred at elevated temperatures. A F.T.-i.r. study revealed that a hydrogen-bonding interaction occurs between these polymers but it is weaker than in pure PHP. The observed miscibility is hence proposed to be the result of specific interactions between the polymers.

TENSILE PROPERTIES OF BLENDS OF POLY(ETHER SULFONE) WITH A POLY(ETHER IMIDE)

Blends of poly(ether sulphone) (PES) with a poly(ether imide) (PEI) in various proportions were prepared by the coprecipitation method. Mechanical properties and morphology of the blends were studied using tensile tests and scanning electron microscopy (SEM). The tensile moduli exhibit positive deviations from simple additivity. Marked positive deviations were also observed for ultimate strength. These results suggest that the PEI/PES blends are mechanically compatible. SEM study revealed that the blends are not homogeneous and the polymers are immiscible on the segmental level. However, the dispersions of the blends are rather fine. The interfaces between the two phases are excellently bonded; PEI and PES appear to interact well.

MISCIBILITY OF POLY(N-VINYL-2-PYRROLIDONE) WITH POLY(ETHER SULFONE) AND 2 PHENOLPHTHALEIN-BASED POLYMERS

Blends of poly(N-vinyl-2-pyrrolidone) (PVP) with poly(ether sulphone) and two phenolphthalein-based polymers, viz. phenolphthalein poly(ether ether sulphone) and phenolphthalein poly(ether ether ketone) were prepared by casting from a common solvent and studied by differential scanning calorimetry. It was found that all the PVP blends are miscible and show a single, composition-dependent glass transition temperature (T(g)). The T(g)-composition dependence has been analysed by the use of the Gordon-Taylor equation. The values of the k parameter in the Gordon-Taylor equation obtained are all not high for the three pairs, in accordance with the fact that there is no strongly specific interaction between PVP and any of the other polymers.