Dielectric thermal analysis as a tool for quantitative-evaluation of the viscosity and the kinetics of epoxy resin cure

Dielectric thermal analysis has been proved as a valuable tool for monitoring the epoxy curing process and the related rheological properties in the fabrication of polymer-matrix composite materials. This technique also has the potential to be applied in the monitoring of magnet impregnation processes as well as in quality control. In this work we present the quantitative evaluation of the viscosity changing and the curing kinetics for a commercial Stycast epoxy resin system at different temperatures through the impedance analysis. The results showed correlation between the real component of the complex impedance and the isothermal reaction extent. Comparing the dielectric analysis result with the viscosity measured by rotational rheometer we observed a similar behavior reported for dynamic mechanic analysis. The results comparison have shown that the kinetics parameters obtained from DSC and DETA analysis showed different sensitivities related to the characteristics of curing stages. We concluded that the dielectric thermal analysis should be applied in quantitative evaluation of cure kinetics.

Corrosion and tribocorrosion behaviour of Al-Si-Cu-Mg alloy and its composites reinforced with B4C particles in 0.05M NaCl solution

The corrosion behaviour of metal matrix composites (MMCs) is strictly linked with the presence of heterogeneities such as reinforcement phase, microcrevices, porosity, secondary phase precipitates, and interaction products. Most of the literature related to corrosion behaviour of aluminium matrix composites (AMCs) is focused on SiC reinforced AMCs. On the other hand, there is very limited information available in the literature related to the tribocorrosion behaviour of AMCs. Therefore, the present work aims to investigate corrosion and tribocorrosion behaviour of Al-Si-Cu-Mg alloy matrix composites reinforced with B4C particulates. Corrosion behaviour of 15 and 19% (vol) B4C reinforced Al-Si-Cu-Mg matrix composites and the base alloy was investigated in 0.05M NaCl solution by performing immersion tests and potentiodynamic polarisation tests. Tribocorrosion behaviour of Al-Si-Cu-Mg alloy and its composites were also investigated in 0.05M NaCl solution. The tests were carried out against alumina ball using a reciprocating ball-on-plate tribometer. Electrochemical measurements were performed before, during, and after the sliding tests together with the recording of the tangential force. Results suggest that particle addition did not affect significantly the tendency of corrosion of Al-Si-Cu-Mg alloy without mechanical interactions. During the tribocorrosion tests, the counter material was found to slide mainly on the B4C particles, which protected the matrix alloy from severe wear damage. Furthermore, the wear debris were accumulated on the worn surfaces and entrapped between the reinforcing particles. Therefore, the tendency of corrosion and the corrosion rate decreased in Al-Si-Cu-Mg matrix B4C reinforced composites during the sliding in 0.05M NaCl solution. © 2013 Elsevier B.V.

Projeto, construção de equipamento para obtenção de compósitos de matriz metálica particulados, utilizando o processo de fundição com agitação mecânica

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Processamento semissólido de liga hipoeutética AlSi reforçada com Al203

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Environmental effects on viscoelastic behavior of carbon fiber/PEKK thermoplastic composites

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Sviluppo, ottimizzazione delle prestazioni e caratterizzazione di materiali compositi a matrice amorfa

Durante l'attività di ricerca sono stati sviluppati tre progetti legati allo sviluppo e ottimizzazione di materiali compositi. In particolare, il primo anno, siamo andati a produrre materiali ceramici ultrarefrattari tenacizzati con fibre di carburo di silicio, riuscendo a migliorare il ciclo produttivo e ottenendo un materiale ottimizzato. Durante il secondo anno di attività ci siamo concentrati nello sviluppo di resine epossidiche rinforzate con particelle di elastomeri florurati che rappresentano un nuovo materiale non presente nel mercato utile per applicazioni meccaniche e navali. L'ultimo anno di ricerca è stato svolto presso il laboratorio materiali di Ansaldo Energia dove è stato studiato il comportamenteo di materiali per turbine a gas.

Molecular Modeling of PMR-15 Polyimide

PMR-15 polyimide is a polymer that is used as a matrix in composites. These composites with PMR-15 matrices are called advanced polymer matrix composite that is abundantly used in the aerospace and electronics industries because of its high temperature resistivity. Apart from having high temperature sustainability, PMR-15 composites also display good thermal-oxidative stability, mechanical properties, processability and low costs, which makes it a suitable material for manufacturing aircraft structures. PMR-15 uses the reverse Diels-Alder (RDA) method for crosslinking which provides it with the groundwork for its distinctive thermal stability and a range of 280-300 degree Centigrade use temperature. Regardless of such desirable properties, this material has a number of limitations that compromises its application on a large scale basis. PMR-15 composites has been known to be very vulnerable to micro-cracking at inter and intra-laminar cracking. But the major factor that hinders its demand is PMR-15's carcinogenic constituent, methylene dianilineme (MDA), also a liver toxin. The necessity of providing a safe working environment during its production adds up to the cost of this material. In this study, Molecular Dynamics and Energy Minimization techniques are utilized to simulate a structure of PMR-15 at a given density of 1.324 g/cc and an attempt to recreate the polyimide to reduce the number of experimental testing and hence subdue the health hazards as well as the cost involved in its production. Even though this study does not involve in validating any mechanical properties of the model, it could be used in future for the validation of its properties and further testing for different properties like aging, microcracking, creep etc.

COMPUTATIONAL STUDY OF MICROSTRUCTURE-PROPERTYMECHANISM RELATIONS IN FERROIC COMPOSITES

Ferroic materials, as notable members of smart materials, have been widely used in applications that perform sensing, actuation and control. The macroscopic property change of ferroic materials may become remarkably large during ferroic phase transition, leading to the fact that the macroscopic properties can be tuned by carefully applying a suitable external field (electric, magnetic, stress). To obtain an enhancement in physical and/or mechanical properties, different kinds of ferroic composites have been fabricated. The properties of a ferroic composite are determined not only by the properties and relative amounts of the constituent phases, but also by the microstructure of individual phase such as the phase connectivity, phase size, shape and spatial arrangement. This dissertation mainly focuses on the computational study of microstructure – property – mechanism relations in two representative ferroic composites, i.e., two-phase particulate magnetoelectric (ME) composite and polymer matrix ferroelectric composite. The former is a great example of ferroic composite exhibiting a new property and functionality that neither of the constituent phases possesses individually. The latter well represents the kind of ferroic composites having property combinations that are better than the existing materials. Phase field modeling was employed as the computing tool, and the required models for ferroic composites were developed based on existing models for monolithic materials. Extensive computational simulations were performed to investigate the microstructure-property relations and the underlying mechanism in ferroic composites. In particulate, it is found that for ME composite 0-3 connectivity (isolated magnetostrictive phase) is necessary to exhibit ME effect, and small but finite electrical conductivity of isolated magnetic phase can beneficially enhance ME effect. It is revealed that longitudinal and transverse ME coefficients of isotropic 0-3 particulate composites can be effectively tailored by controlling magnetic domain structures without resort to anisotropic two-phase microstructures. Simulations also show that the macroscopic properties of the ferroelectricpolymer composites critically depend on the ferroelectric phase connectivity while are not sensitive to the sizes and internal grain structures of the ceramic particles. Texturing is found critical to exploit the paraelectric«ferroelectric phase transition and nonlinear polarization behavior in paraelectric polycrystal and its polymer matrix composite. Additionally, a Diffuse Interface Field model was developed to simulate packing and motion in liquid phase which is promising for studying the fabrication of particulatepolymer composites.

Incorporación de escorias de aluminio en la fabricación de productos de Arcilla cocida

Las sociedades desarrolladas generan una gran cantidad de residuos, que necesitan una adecuada gestión. Esta problemática requiere, de este modo, una atención creciente por parte de la sociedad, debido a la necesidad de proteger el medio ambiente. En este sentido, los esfuerzos se centran en reducir al máximo la generación de residuos y buscar vías de aprovechamiento de aquellos que son inevitables, soluciones mucho más aconsejables desde el punto de vista técnico, ecológico y económico que su vertido o destrucción. Las industrias deben adoptar las medidas precisas para fomentar la reducción de estos residuos, desarrollar tecnologías limpias que permitan el ahorro de los recursos naturales que poseemos, y sobre todo buscar métodos de reutilización, reciclado, inertización y valorización de los residuos generados en su producción. La industria de la construcción es un campo muy receptivo para el desarrollo de nuevos materiales en los que incorporar estos residuos. La incorporación de diferentes residuos industriales en matrices cerámicas se plantea como una vía barata de fijar las diferentes especies metálicas presentes en transformación de rocas ornamentales, lodos de galvanización o metalúrgicos, etc. En todos los casos, la adición de estos residuos requiere su caracterización previa y la optimización de las condiciones de conformado y cocción en el caso de su incorporación a la arcilla cocida. Entre los residuos incorporados en materiales de construcción se encuentran las escorias de aluminio. La industria metalúrgica produce durante sus procesos de fusión diferentes tipos de escorias. Su reciclado es una de las líneas de interés para estas industrias. En el caso de las escorias de aluminio, su tratamiento inicial consiste en una recuperación del aluminio mediante métodos mecánicos seguido de un tratamiento químico, o plasma. Este método conduce a que la escoria final apenas contenga aluminio y sea rica en sales solubles lo que limita su almacenamiento en escombreras. La escoria es una mezcla de aluminio metal y productos no metálicos como óxidos, nitruros y carburos de aluminio, sales y otros óxidos metálicos. En este estudio se ha analizado la posibilidad de la adición de escorias de aluminio procedentes de la metalurgia secundaria en materiales de construcción, de forma que tras un procesado de las mismas permita la obtención de materiales compuestos de matriz cerámica. En la presente Tesis Doctoral se ha analizado la viabilidad técnica de la incorporación de las escorias de aluminio procedentes de la metalurgia secundaria en una matriz de arcilla cocida. Para ello se han aplicado diferentes tratamientos a la escoria y se han aplicado diferentes variables en su procesado como la energía de molienda o la temperatura de sinterizacion, además del contenido de escoria. Su compactación con agua entre el 5-10 %, secado y sinterización permite obtener piezas rectangulares de diverso tamaño. Desde el punto de vista del contenido de la escoria, se incorporó entre un 10 y 40% de escoria TT, es decir sometida una calcinación previa a 750ºC en aire. Los mejores resultados alcanzados corresponden a un contenido del 20% ESC TT, sinterizada a 980ºC, por cuanto altos contenidos en escoria condicen a piezas con corazón negro. Los productos obtenidos con la adición de 20% de escoria de aluminio a la arcilla, presentan una baja expansión tras sinterización, mejores propiedades físicas y mecánicas, y mayor conductividad térmica que los productos obtenidos con arcilla sin adiciones. Aumenta su densidad, disminuye su absorción y aumenta sus resistencias de flexión y compresión, al presentar una porosidad cerrada y una interacción escoria-matriz. En todos los casos se produce una exudación superficial de aluminio metálico, cuyo volumen está relacionado con la cantidad de escoria adicionada. Mediante la incorporación de este contenido de escoria, tras un tratamiento de disolución de sales y posterior calcinación (ESC TTQ), se mejoran las propiedades del material compuesto, no sólo sobre la de la escoria calcinada (ESC TT), sino también, sobre la escoria sin tratamiento (ESC). Si además, la adición del 20% de escoria añadida, está tratada, no sólo térmicamente sino también químicamente (ESC TTQ), éstas mejoran aún más las propiedades del material compuesto, siendo el producto más compacto, con menos poros, por lo que los valores de densidad son más elevados, menores son las absorciones y mayores resistencias de flexión y compresión, que los productos obtenidos con la adición de escoria sólo tratada térmicamente. Alcanzando valores de resistencias características a compresión del orden de 109 MPa. Los valores de conductividad térmica obtenidos también son mayores. Los ensayos tecnológicos con piezas de 160 x 30 x 5 mm y el material compuesto optimizado de arcilla+ 20%ESCTTQ, consistieron en la determinación de su expansión por humedad, eflorescencia y heladicidad, mostrando en general un mejor comportamiento que la arcilla sin adiciones. Así, se han obtenido nuevos materiales compuestos de matriz cerámica para la construcción, mejorando sus propiedades físicas, mecánicas y térmicas, utilizando escorias de aluminio procedentes de la metalurgia secundaria, como opción de valorización de estos residuos, evitando así, que se viertan a vertederos y contaminen el medio ambiente. ABSTRACT Developed societies generate a lot of waste, which need proper management. Thus, this problem requires increased attention from the society, due to the need to protect the environment. In this regard, efforts are focused on to minimize the generation of waste and find ways of taking advantage of those who are inevitable, much more advisable solutions from the technical, ecological and economic viewpoint to disposal or destruction. Industries should adopt precise measures to promote waste reduction, develop clean technologies that allow the saving of natural resources that we possess, and above all seek methods of reuse, recycling, recovery and valorisation of the waste generated in their production. The industry of the construction is a very receptive field for the development of new materials in which to incorporate these residues. The incorporation of different industrial residues in ceramic counterfoils appears as a cheap route to fix the different metallic present species in transformation of ornamental rocks, muds of galvanization or metallurgical, etc. In all the cases, the addition of these residues needs his previous characterization and the optimization of the conditions of conformed and of baking in case of his incorporation to the baked clay. Residues incorporated into construction materials include aluminium slag. The metallurgical industry produces during their fusion processes different types of slags. Recycling is one of the lines of interest to these industries. In the case of aluminium slag, their initial treatment consists of a recovery of the aluminium using mechanical methods followed by chemical treatment, or plasma. This method leads to that final slag just contains aluminium and is rich in soluble salts which limits storage in dumps. The slag is a mixture of aluminium metal and non-metallic such as oxides, nitrides and carbides of aluminium salts products and other metal oxides. The present Doctoral thesis has analysed the technical viability of the incorporation of aluminium slag from secondary Metallurgy in an array of baked clay. So they have been applied different treatments to the slag and have been applied different variables in its processing as the temperature of sintering, in addition to the content of slag or energy grinding. Its compaction with water between 5-10%, drying and sintering allows rectangular pieces of different size. From the point of view of the content of the slag, it is incorporated between 10 and 40% slag TT, that is to say, submitted a calcination prior to 750 ° C in air. The best results achieved correspond to 20% ESC TT, sintered at 980 ° C, as high levels of slag in accordance to pieces with black heart. The products obtained with the addition of 20% of slag from aluminium to clay, present a low expansion after sintering, better physical properties and mechanical, and higher thermal conductivity than the products obtained with clay, without addictions. Its density increases, decreases its absorption and increases its resistance to bending and compression, introducing a closed porosity and slag-matrix interaction. In all cases there is a superficial exudation of metallic aluminium, whose volume is related to the amount of slag added. By incorporating this content of slag, following a treatment of salt solution and subsequent calcination (ESC TTQ), are improved the properties of composite material not only on the calcined slag (ESC TT), but also in the slag without treatment (ESC). If the addition of 20% of slag added, is also treated, not only thermally but also chemically (ESC TTQ), they further improve the properties of the composite material, the product is more compact, less porous, so the values are higher density, minors are absorptions and greater resistance in bending and compression, to the products obtained with the addition of slag only treated thermally. Reaching values of compressive resistance characteristic of the order of 109 MPa. The thermal conductivity values obtained are also higher. Testing technology with pieces of 160 x 30 x 5 mm and optimized composite material of clay 20% ESCTTQ, consisted in the determination of its expansion by moisture, efflorescence and frost resistance, in general, showing a better performance than the clay without additions. Thus, we have obtained new ceramic matrix composite materials for construction, improving its physical, mechanical and thermal properties, using aluminium slag secondary metallurgy, as an option Valuation of these wastes, thus preventing them from being poured to landfills and pollute environment.

Efeitos da soldagem por laser de fibra de Yb na microestrutura do compósito A356/SiCp

Materiais compósitos são projetados e fabricados para várias aplicações de alto desempenho, incluindo componentes para os segmentos automobilístico, aeroespacial, aeronáutico, naval, de defesa, de óleo e gás, energia eólica e até equipamentos esportivos. Porém, a união por soldagem de Compósitos de Matriz Metálica de Alumínio (Al-CMM) ainda é um grande obstáculo para a maior disseminação desta classe de materiais estruturais. As mudanças microestruturais decorrentes do ciclo de soldagem e/ou do tratamento térmico afetam sensivelmente as propriedades mecânicas e físico-químicas finais da junta e do metal base nas proximidades de mesma, daí a importância de se estudar a evolução microestrutural que prospera nestas etapas. O presente trabalho caracterizou a microestrutura do compósito liga-A356/SiCp soldado por laser de fibra de Itérbio, empregando-se nessa tarefa técnicas de microscopia óptica, radiografia e microscopia eletrônica de varredura, assim como difração de raios-X e de elétrons retroespalhados, ensaio instrumentado de dureza e microtomografia computadorizada. O foco das análises realizadas restringiu-se à geometria dos cordões de solda, à expulsão de SiC particulado da zona soldada, à volatilização de elementos químicos da poça de soldagem, à formação de precipitados fragilizantes de Al4SiC4 em formato de agulhas no cordão de solda e à determinação das regiões com concentração de poros, todos estes fenômenos tendo efeitos nocivos, em maior ou menor extensão, no desempenho global da junta do Al-CMM soldada a laser, notadamente em suas propriedades mecânicas e eletroquímicas.

In situ TiB-reinforced Cu-based bulk metallic glass composites

Cu-based bulk metallic glass (BMG) composites containing in situ TiB particles were successfully fabricated. The reinforcing TiB particles with a size of 5-10 mu m are uniformly distributed in the amorphous matrix. The particles have a good bonding to the matrix with a reaction layer. The BMG composites exhibit an obvious ductility with a plastic strain of 2% for the 17.5 vol.% TiB sample due to the suppression of shear band propagation and the generation of multiple shear bands during compressive testing. The hardness of the materials is increased from Hv543 for monolithic BMG to Hv650 for 23.6 vol.% TiB-containing BMG composite. (c) 2006 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Advanced UV inscribed fibre grating structures and applications in optical sensing and laser systems

This thesis presents detailed investigation of UV inscribed fibre grating based devices and novel developments in the applications of such devices in optical sensing and fibre laser systems. The major contribution of this PhD programme includes the systematic study on fabrication, spectral characteristics and applications of different types of UV written in-fibre gratings such as Type I and IA Fibre Bragg Gratings (FBGs), Chirped Fibre Bragg Gratings (CFBGs) and Tilted Fibre Gratings (TFGs) with small, large and 45º tilted structures inscribed in normal silica fibre. Three fabrication techniques including holographic, phase-mask and blank beam exposure scanning, which were employed to fabricate a range of gratings in standard single mode fibre, are fully discussed. The thesis reports the creation of smart structures with self-sensing capability by embedding FBG-array sensors in Al matrix composite. In another part of this study, we have demonstrated the particular significant improvements made in sensitising standard FBGs to the chemical surrounding medium by inducing microstructure to the grating by femtosecond (fs) patterning assisted chemical etching technique. Also, a major work is presented for the investigation on the structures, inscription methods and spectral Polarisation Dependent Loss (PDL) and thermal characteristics of different angle TFGs. Finally, a very novel application in realising stable single polarisation and multiwavelength switchable Erbium Doped Fibre Lasers (EDFLs) using intracavity polarisation selective filters based on TFG devices with tilted structures at small, large and exact 45° angles forms another important contribution of this thesis.

The properties of advanced alumimium alloy systems

2XXX and 7XXX series aluminium alloys have been the accepted materials for airframe construction for many decades. However, only minor improvements in properties have been possible by the development of these alloys since the early 1970's. The constant need to reduce weight in aircraft has therefore led to a resurgence in the research for higher performance aluminium alloys. The reason for this investigation was to evaluate possible alternatives for the existing conventional aluminium alloy 2014 for aircraft wheel applications. Three new technologies in alloy development were considered: a metal matrix composite, an aluminium-lithium alloy and a powder metallurgical alloy. The basic mechanical properties of these advanced materials have already been established to an extent, but their fatigue behaviour has yet to be fully understood. The purpose of this work was to investigate the fatigue properties of the materials concerned, in both air and an aerated 3.5% NaCl solution, and compare these properties to 2014-T6. As well as the basic mechanical properties, fatigue crack propagation data is presented for all of the materials concerned. Additionally, fatigue crack initiation data is presented for the aluminium-lithium alloy and 2014. The D.C. electrical potential method was used to monitor crack growth. Of the materials investigated, the most promising was the aluminium-lithium alloy. However, short transverse properties need to be increased and the commercial cost of the material needs to be decreased before it can be considered as a direct replacement for 2014 for aircraft structural applications. It was considered that the cost of the powder metallurgical alloy would limit its further use. The metal matrix composite material proved to be unsuitable for most ambient temperature applications

Influência da absorção de umidade no comportamento mecânico nos compósitos poliméricos híbridos Kevlar/vidro quando imerso em água do mar e petróleo

The polymer matrix composite materials are being used on a large scale in the most different industrial fields such as aerospace, automotive, oil, among others, since the industrial perspectives is currently working with materials which have a good mechanical performance at high service life and cost / benefit. Thus, the determination of the mechanical properties is indispensable for the characterization of waste resulting in greater expansion of this type of material. Thus, this work will be obtained three plates laminated with tereftálica polymeric matrix reinforced by a bidirectional woven E-glass and kevlar both industrially made, where the plates are manufactured by manual lamination process (hand lay-up), all laminates have five enhancement layers, the first hybrid laminate will consist of bidirectional woven E-glass fiber, kevlar fiber interspersed with layers, is formed by the second bidirectional woven kevlar fiber at the ends of the laminate (two layers), and in the center the glass fiber fabric (three layers), the third plate is composed of only the bidirectional woven E-glass fiber. Then were prepared specimens (CP) by standard, to determine the mechanical properties of tensile and bending in three points. After fabrication of the specimens, they were immersed in oil and seawater. After that, there was a comparison of the mechanical properties for the test condition in the dry state. Showing that there was a considerable increase in the properties studied because the effect of hybridization in laminates.

Obtenção e caracterização de um compósito de matriz polimérica com carga de resíduos vegetal proveniente do sabugo de milho

The feasibility of using the corn cob to obtain a polymer matrix composite was studied. To obtain the bran, corncob passed the drying process in a solar dryer, and was subsequently triturated in forage and to obtain the different particle sizes, by sieving. Three different grain sizes were used: fine particles (FP) size between 0,10 and 2mm; sized particles (PM) with sizes between 2,10 and 3,35 mm; large particles (PG) sizes between 3,45 and 4,10 mm. Using 20% of residue relative to the resin, the test samples were constructed for characterization of the composite, taking into account thermal and mechanical parameters. The main advantage of the proposed composite is that it has a low density, below the relative resin, about 1.06 kg / m³ for the PG. The composite showed a mechanical behavior less than of the resin to the grain sizes and for all formulations studied. Showed better results for the bending, reaching 25.3 MPa for the PG. The composite also showed be feasible for thermal applications, with thermal conductivity less than 0.21 W / m, ranking as insulation. In terms of homogeneity of the mixture, the most viable grain size is the PF, which also showed improved aesthetics and better processability. This composite can be used to make structures that do not require significant mechanical strength, such as tables, chairs, planks, and solar and wind prototypes, such as ovens and cookers and turbines blades.