What can light scattering spectroscopy do for membrane-active peptide studies

Highly charged peptides are important components of the immune system and belong to an important family of antibiotics. Although their therapeutic activity is known, most of the molecular level mechanisms are controversial. A wide variety of different approaches are usually applied to understand their mechanisms, but light scattering techniques are frequently overlooked. Yet, light scattering is a noninvasive technique that allows insights both on the peptide mechanism of action as well as on the development of new antibiotics. Dynamic light scattering (DLS) and static light scattering (SLS) are used to measure the aggregation process of lipid vesicles upon addition of peptides and molecular properties (shape, molecular weight). The high charge of these peptides allows electrostatic attraction toward charged lipid vesicles, which is studied by zeta potential (zeta-potential) measurements. Copyright (c) 2008 European Peptide Society and John Wiley & Sons, Ltd.

Obtaining NiAl intermetallic compound using different milling devices

NiAl intermetallic compound was synthesized by mechanical alloying technique in planetary and attritor mills. The starting powders consisted of elemental mixtures of Ni and Al at Ni50Al50(at%) composition. In the planetary mill, compound formation occurred gradually during mechanical alloying, while the occurrence of a mechanically induced self-propagating reaction (MSR) can be suggested in the attritor mill. The NiAl obtained in both mill types was partially disordered with long-range order parameter not inferior to 0.66. Quantitative phase analysis using the Rietveld method was performed in as-milled samples, and this method was also employed to estimate changes in crystallite size and lattice strain of the NiAl produced during mechanical alloying. (C) 2011 The Society of Powder Technology Japan. Published by Elsevier B.V. and The Society of Powder Technology Japan. All rights reserved.

Low-dimensional carbon allotropes: an electron microscopy investigation

The research reported in this manuscript concerns the structural characterization of graphene membranes and single-walled carbon nanotubes (SWCNTs). The experimental investigation was performed using a wide range of transmission electron microscopy (TEM) techniques, from conventional imaging and diffraction, to advanced interferometric methods, like electron holography and Geometric Phase Analysis (GPA), using a low-voltage optical set-up, to reduce radiation damage in the samples. Electron holography was used to successfully measure the mean electrostatic potential of an isolated SWCNT and that of a mono-atomically thin graphene crystal. The high accuracy achieved in the phase determination, made it possible to measure, for the first time, the valence-charge redistribution induced by the lattice curvature in an individual SWCNT. A novel methodology for the 3D reconstruction of the waviness of a 2D crystal membrane has been developed. Unlike other available TEM reconstruction techniques, like tomography, this new one requires processing of just a single HREM micrograph. The modulations of the inter-planar distances in the HREM image are measured using Geometric Phase Analysis, and used to recover the waviness of the crystal. The method was applied to the case of a folded FGC, and a height variation of 0.8 nm of the surface was successfully determined with nanometric lateral resolution. The adhesion of SWCNTs to the surface of graphene was studied, mixing shortened SWCNTs of different chiralities and FGC membranes. The spontaneous atomic match of the two lattices was directly imaged using HREM, and we found that graphene membranes act as tangential nano-sieves, preferentially grafting achiral tubes to their surface.

Charakterisierung antiker Keramik und ihrer Herstellungstechniken mit mineralogischen Methoden am Beispiel Mayener Gebrauchskeramik

Mehr als hundert Jahre archäologischer Forschung haben gezeigt, dass in Mayen in römischer und mittelalterlicher Zeit eines der wichtigsten europäischen Produktionszentren für die Herstellung qualitätsvoller Gebrauchskeramik bestand. Im Rahmen dieser Studie wurden vier Befundkomplexe aus Töpfereisiedlungen vom 4. bis in das 14. Jahrhundert untersucht. Genauer handelt es sich um Keramik aus zwei spätantiken Brennanlagen des 4. Jahrhunderts im Bereich der Flur „Auf der Eich“ an den Straßen „Am Sonnenhang“ und „Frankenstraße“. Weiterhin konnte Material aus zwei Töpferofenfüllungen des 5. bis 9. Jahrhunderts analysiert werden, das 1975 auf dem Grundstück 55 an der „Siegfriedstraße“ in Brennanlagen entdeckt wurde. Hinzu kam Brenngut aus elf Töpferöfen des späten 8. bis 14. Jahrhunderts, welches in den so genannten „Burggärten“ der Genovevaburg von Mayen in den Jahren 1986/87 durch die archäologische Denkmalpflege in Koblenz geborgen wurde. Die mineralogischen Untersuchungen zur Charakterisierung der „Mayener Keramik“ wurden systematisch an den Keramikmaterialien aus diesen Fundstellen durchgeführt. Mittelalterliche Keramik aus Bornheim-Walberberg, Brühl-Eckdorf, Höhr-Grenzhausen, Langerwehe, Frechen, Brühl-Pingsdorf, Paffrath, Raeren, Ratingen-Breitscheid, Siegburg-Seehofstraße, Siegburg-Scherbenhügel, Fredelsloh und Brühl-Badorf konnte für diese Arbeit als Referenzmaterialien ebenfalls untersucht werden. Provenienzanalysen wurden an Keramikproben aus 27 Fundorten, die makroskopisch nach Mayener Ware aussehen, mit mineralogischen Methoden durchgeführt, um sie der Fundregion Mayen eindeutig zuordnen zu können.rnPhasenanalyse, chemische Analyse und thermische Analyse wurden an Keramik sowie Ton durchgeführt. Die Phasenanalyse wurde zur Bestimmung der mineralischen Zusammensetzung von Grundmasse und Magerungsmittel (Röntgendiffraktometrie (XRD), Polarisationsmikroskop, Mikro-Raman-Spektroskopie) verwendet. Die chemische Zusammensetzung wurde durch Röntgenfluoreszenzanalyse (RFA) ermittelt. Elektronenstrahlmikroanalyse (ESMA) und Laser-Massenspektrometrie mit induktiv gekoppeltem Plasma (LA-ICP-MS) wurden bei den Proben, bei denen weniger als 2g Material zur Verfügung standen, eingesetzt. Brennexperimente wurden am originalen Rohstoff der Keramik aus den „Burggärten“ der Genovevaburg durchgeführt. Gebrannter Ton wurde durch Röntgendiffraktometrie (XRD), Infrarotspektroskopie (IR) und Differential-Thermoanalyse (DTA) analysiert. rnAnhand der Messergebnisse lässt sich die Mayener Keramik aus den vier Fundplätzen in zwei Typen zusammenzufassen: der mit Feldspat-reichem Sand gemagerte römische Typ und der mit Quarz-reichem Sand gemagerte mittelalterliche Typ. Die Änderung des Magerungsmittels von Feldspat- zu Quarzsand weist eine technische Entwicklung zu höheren Brenntemperaturen von der Römerzeit bis in das Mittelalter nach. Nach der Untersuchung und dem Vergleich mit den Referenzkeramikgruppen ist festzustellen, dass durch multivariate Statistikanalysen der chemischen Komponenten die Charakterisierung der Keramik und eine Differenzierung zwischen den Keramikgruppen gelingt. Diese Erkenntnisse bildeten die Basis für Provenienzanalysen. 16 Fundorte können durch Provenienzanalyse sicher als Exportregionen der Mayener Ware festgestellt werden. Gemäß den Brennexperimenten lassen sich die chemischen Reaktionen während des Brandprozesses nachvollziehen. Zwei Methoden wurden mittels Röntgendiffraktometrie (XRD) und Differential-Thermoanalyse (DTA) zur Bestimmung der Brenntemperaturen der Keramik modelliert. Die Töpferöfen der „Burggärten“ können nach der Brenntemperatur in zwei Typen zusammengefasst werden: solche mit einer Brenntemperatur unter 1050°C und solche mit einer Brenntemperatur über 1050°C.rn

Thermal structure and dynamical modeling of a Mediterranean tropical-like cyclone

In the present work, a detailed analysis of a Mediterranean TLC occurred in January 2014 has been conducted. The author is not aware of other studies regarding this particular event at the publication of this thesis. In order to outline the cyclone evolution, observational data, including weather-stations data, satellite data, radar data and photographic evidence, were collected at first. After having identified the cyclone path and its general features, the GLOBO, BOLAM and MOLOCH NWP models, developed at ISAC-CNR (Bologna), were used to simulate the phenomenon. Particular attention was paid on the Mediterranean phase as well as on the Atlantic phase, since the cyclone showed a well defined precursor up to 3 days before the minimum formation in the Alboran Sea. The Mediterranean phase has been studied using different combinations of GLOBO, BOLAM and MOLOCH models, so as to evaluate the best model chain to simulate this kind of phenomena. The BOLAM and MOLOCH models showed the best performance, by adjusting the path erroneously deviated in the National Centre for Environmental Prediction (NCEP) and ECMWF operational models. The analysis of the cyclone thermal phase shown the presence of a deep-warm core structure in many cases, thus confirming the tropical-like nature of the system. Furthermore, the results showed high sensitivity to initial conditions in the whole lifetime of the cyclone, while the Sea Surface Temperature (SST) modification leads only to small changes in the Adriatic phase. The Atlantic phase has been studied using GLOBO and BOLAM model and with the aid of the same methodology already developed. After tracing the precursor, in the form of a low-pressure system, from the American East Coast to Spain, the thermal phase analysis was conducted. The parameters obtained showed evidence of a deep-cold core asymmetric structure during the whole Atlantic phase, while the first contact with the Mediterranean Sea caused a sudden transition to a shallow-warm core structure. The examination of Potential Vorticity (PV) 3-dimensional structure revealed the presence of a PV streamer that individually formed over Greenland and eventually interacted with the low-pressure system over the Spanish coast, favouring the first phase of the cyclone baroclinic intensification. Finally, the development of an automated system that tracks and studies the thermal phase of Mediterranean cyclones has been encouraged. This could lead to the forecast of potential tropical transition, against with a minimum computational investment.

Right ventricular systolic function and cardiac resynchronization therapy

AIMS: The effect of cardiac resynchronization therapy (CRT) on right ventricular ejection fraction (RVEF) has not been well studied. Furthermore, it is unclear whether baseline RVEF influences response to CRT. To evaluate the acute and chronic effects of CRT on right ventricular systolic function, and to investigate whether baseline RVEF impacts response to CRT. METHODS AND RESULTS: Forty-four patients with a standard indication for CRT underwent radionuclide angiography at baseline and after at least 6 months' follow-up for measuring RVEF, right ventricular synchrony (using phase analysis), and left ventricular ejection fraction (LVEF). In addition, NYHA functional class and 6-min walking distance (6MWD) were evaluated. There were no significant acute changes in RVEF with CRT. After a mean follow-up of 9 +/- 5 months, RVEF was slightly improved (by 1.9 +/- 5.0% in absolute terms, P = 0.016), and to a lesser extent than LVEF (5.1 +/- 9.0%, P = 0.009 compared with RVEF). Right ventricular dyssynchrony was significantly improved at follow-up (P = 0.016). Patients with a baseline RVEF < or = 0.35 (n = 19) were less likely to improve in NYHA class (P = 0.016), and also tended to improve less in 6MWD and LVEF (P < 0.06). CONCLUSION: Cardiac resynchronization therapy has no acute effect on RVEF, and only slightly improves RVEF at follow-up. Patients with reduced RVEF at baseline were less likely to respond to CRT, indicating that right ventricular systolic dysfunction may play a role in patient selection.

Archivos y empresas : Un consenso ineludible

El artículo que presentamos tiene por objeto analizar la necesaria presencia de un servicio de archivos en las empresas, en aras de la rentabilidad y la eficacia. Para ello, estructuramos el trabajo en dos apartados: por un lado, analizamos las propiedades que hoy caracterizan a la Archivística y proponemos una definición de nuestra disciplina; por otro, nos centramos en la necesaria acción de la gestión documental en las empresas. Tras describir en qué consiste dicha gestión documental, exponemos las fases para la planificación de un sistema archivístico en cualquier organización empresarial (fase de análisis, elaboración y diseño, implantación del sistema y control). Para esto último, realizamos una comparación sistemática de lo que dicen al respecto algunos autores

Archivos y empresas : Un consenso ineludible

El artículo que presentamos tiene por objeto analizar la necesaria presencia de un servicio de archivos en las empresas, en aras de la rentabilidad y la eficacia. Para ello, estructuramos el trabajo en dos apartados: por un lado, analizamos las propiedades que hoy caracterizan a la Archivística y proponemos una definición de nuestra disciplina; por otro, nos centramos en la necesaria acción de la gestión documental en las empresas. Tras describir en qué consiste dicha gestión documental, exponemos las fases para la planificación de un sistema archivístico en cualquier organización empresarial (fase de análisis, elaboración y diseño, implantación del sistema y control). Para esto último, realizamos una comparación sistemática de lo que dicen al respecto algunos autores

Archivos y empresas : Un consenso ineludible

El artículo que presentamos tiene por objeto analizar la necesaria presencia de un servicio de archivos en las empresas, en aras de la rentabilidad y la eficacia. Para ello, estructuramos el trabajo en dos apartados: por un lado, analizamos las propiedades que hoy caracterizan a la Archivística y proponemos una definición de nuestra disciplina; por otro, nos centramos en la necesaria acción de la gestión documental en las empresas. Tras describir en qué consiste dicha gestión documental, exponemos las fases para la planificación de un sistema archivístico en cualquier organización empresarial (fase de análisis, elaboración y diseño, implantación del sistema y control). Para esto último, realizamos una comparación sistemática de lo que dicen al respecto algunos autores

Determinación y caracterización de los indicadores que intervienen en un sistema integral de iluminación natural y protección solar : aplicado a la incorporación de bandejas en los huecos de fachadas existentes

En esta tesis se estudia cómo lograr el equilibrio entre dos fenómenos naturales que afectan a los huecos de fachadas: la iluminación natural y la ganancia solar. Es decir, el cómo, conseguir la optimización de la iluminación natural que se introduce a través de las ventanas existentes, sin realizar una laboriosa intervención de sustitución de las mismas y el cómo, conseguir la protección de la radiación solar directa de la zona acristalada, para evitar tanto las ganancias térmicas innecesarias como el deslumbramiento que afecta a la calidad lumínica de los recintos. Para el desarrollo esta investigación se ha propuesto una metodología de estudio dividida en dos fases: La primera, de Análisis y Diagnóstico, en la que se han de definir los estándares a cumplir y las variables con las que se evaluarán las bandejas. Y, la segunda, de Evaluación y Comprobación en la que se han de establecer los criterios de valoración y ponderación de cada variable. En la primera fase, se definirán las variables físico-ambientales, para lo que se seleccionarán algunas ciudades a estudiar, a las cuales se les estudiará las necesidades de confort térmico, se determinarán las dimensiones que deben tener las protecciones solares en esas ciudades, además se determinarán las actuaciones a realizar en los huecos de fachada según sea su posición en el plano vertical de la misma. Así mismo, se plantea hacer un análisis de casos reales, para lo que se caracterizarán desde el punto de vista lumínico algunas viviendas, realizando medidas “in situ” y comparando resultados con los que se obtienen de los programas de simulación, para seleccionar las viviendas en las que la realidad y la simulación se aproximen más, una de estas viviendas servirá de modelo en las simulaciones que se realizará en la segunda fase. También, en esta primera fase, mediante un modelo neutro, se estudiará el comportamiento térmico y lumínico del tamaño del hueco en el que se insertará la bandeja posteriormente, para luego estudiar la posición de la bandeja en el plano vertical de la ventana, desde el punto de vista ergonómico. Y finalmente se estudiará, el comportamiento térmico y lumínico del modelo con la bandeja ubicada a 40, 50 y 60cm del techo. En la segunda fase, se establecerá la valoración y ponderación de las variables con las que seleccionar la bandeja que mejor equilibre los aspectos térmicos y lumínicos, teniendo en cuenta estrategias pasivas de acondicionamiento ambiental, como favorecer las ganancias solares en invierno en horas diurnas y evitar las pérdidas de calor en horas nocturnas; y en verano implementar sistemas de sombreamiento en la zona acristalada para evitar las ganancias de calor; y, tanto en verano como en invierno, aprovechar la iluminación natural, para favorecer la iluminancia útil y evitar el deslumbramiento. Una vez definidos los criterios de valoración y ponderación se aplicará a la evaluación térmica y lumínica del modelo neutro con la bandeja, consiguiendo seleccionar la bandeja con mejor comportamiento. Posteriormente se comprobará la metodología de estudio desarrollada en el modelo seleccionado, se evaluará el comportamiento térmico y lumínico, con la incorporación de algunas alternativas de bandeja. Con esta investigación se quiere demostrar que mediante la aplicación de esta metodología de estudio, es posible evaluar y seleccionar bandejas que respondan a las necesidades requeridas en distintos casos de estudio, por lo que se considera que, la bandeja puede ser un elemento arquitectónico aplicable tanto en rehabilitación como en nueva construcción, de espacios en los que sea necesario mejorar sus condiciones lumínicas y térmicas simultáneamente. ABSTRACT This thesis studies how to balance two natural events that affect the window opening of facades: daylighting and solar gain. That is to say, how to achieve optimization of natural light that gets in through the existing windows, without making a laborious intervention of replacing them and how to get protection from direct solar radiation from the glass area, to avoid unnecessary heat gain and glare affecting the light quality of the enclosures. To develop this research, it has been proposed a methodology of study divided into two phases: First phase, Analysis and Diagnostics, in which the variables with which the light shelf are evaluated will be defined along with the standards the light shelves will meet. The second phase, Assessment and Verification, in which the assessment criteria and weighting of each variable will be established. In the first phase, the physical and environmental variables shall be defined, various cities will be selected to be studied, and in each the needs of thermal comfort will be determined along with the dimensions of shading devices in the cities. In addition the actions to be taken in the window opening of the façade will be determined, depending on their position in the vertical plane. An analysis of real cases will be undertaken, which will be characterized from the luminous point of view, performing "in situ" measurements and comparing results with those obtained from simulation programs, to select places/dwellings where reality and simulation are closer, one of these places/dwellings will be a model, in the simulations to perform at the second phase. Also, in this first phase, by a neutral model, the thermal and light behavior of the size of the window opening will be studied, in which the light shelf is inserted later, the position of the light shelf in the vertical plane of the window is studied, from an ergonomic point of view. And finally to study the thermal and light behavior of the model with the light shelf located at 40, 50 and 60cm from the ceiling. In the second phase, the evaluation and weighting of the variables will be established selecting the light shelf that best balances the thermal and daylighting aspects, taking into account passive environmental conditioning strategies; such as getting solar gains in winter during daylight hours, and preventing heat loss during the night hours; and in summer implementing shading systems in the glazing area to avoid heat gains. And in both summer and winter, taking advantage of natural lighting, to improve useful illuminance and avoid glare. Once defined, the evaluation criteria and weighting will be applied to thermal and daylighting evaluation to the neutral model with the light shelf, the best performing light shelf will be selected. The study methodology developed in the selected model will be verified the thermal and daylighting performance with the addition of some light shelf alternative will also be studied. With this research, we want to show that by applying this study methodology it is possible to evaluate and select the light shelf that meets the needs required in different case studies, so it is considered that the light shelf may be an applicable architectural element in both refurbishment and new construction of spaces where necessary to improve their daylighting and thermal conditions simultaneously.

Dynamics of on-line learning in radial basis function networks

On-line learning is examined for the radial basis function network, an important and practical type of neural network. The evolution of generalization error is calculated within a framework which allows the phenomena of the learning process, such as the specialization of the hidden units, to be analyzed. The distinct stages of training are elucidated, and the role of the learning rate described. The three most important stages of training, the symmetric phase, the symmetry-breaking phase, and the convergence phase, are analyzed in detail; the convergence phase analysis allows derivation of maximal and optimal learning rates. As well as finding the evolution of the mean system parameters, the variances of these parameters are derived and shown to be typically small. Finally, the analytic results are strongly confirmed by simulations.

Synthesis of M2AC (M = Ti, V, Cr, Nb, Zr, A = Al, Sn, S) (MAX) carbide phases and study of their physical behavior under extreme conditions

Materials known as Mn+1AXn phases, where n is 1, 2, or 3, and M represents an early transition metal, A an A-group element, and X is either Carbon and/or Nitrogen [1], are fast becoming technologically important materials due to the interesting combination of unique properties. However, a lot of important information about the high temperature and high pressure behavior of many of these compounds is still missing, which needs to be determined systematically. ^ In this dissertation the synthesis of M2AC (M = Ti, V, Cr, Nb, Zr) and A = (Al, Sn, S) compounds by arc melting, vacuum sintering and piston cylinder synthesis is presented along with the synthesis of Zr 2SC, which has been synthesized for first time in bulk form, by piston cylinder technique. The microstructural analysis by electron microscopy and phase analysis by x-ray diffraction is presented next. Finally, a critical analysis of the behavior of these compounds under the application of extreme pressure (as high as 50 GPa) and temperature (≈ 1000°C) is presented. ^ The high pressure studies, up to 50 GPa, showed that these compounds were structurally intact and their bulk moduli ranged from 140 to 190 GPa. The high temperature studies in the inert atmosphere showed that the M 2SnC compounds were unstable above 650°C and the expansion along the a-axis was higher than that along the c-axis, unlike the other phases. M2SC compounds on the other hand showed negligible difference in the thermal expansion along the two axes. The oxidation study revealed that Ti2AC (Al, S) compounds had highest resistance to oxidation while the M2SnC compounds had the least. Furthermore, from the oxidation study of these compounds, which were short time oxidation experiments, it was found that all of these compounds oxidized to their respective binary oxides. ^

Produção de CDR a partir de resíduos industriais: caso de estudo da Recivalongo

A produção de combustível derivado de resíduos (CDR) resultou de uma decisão política que permitiu a instalação em Portugal de um significativo conjunto de processos, cuja avaliação técnico-económica e ambiental pode já ser feita. Este trabalho faz uma avaliação técnica e ambiental da linha de produção de CDR da Recivalongo. A avaliação técnica consistiu na análise dos caudais de material que entraram na linha de produção, na quantidade de CDR produzido, contabilizando também os gastos de recursos da linha (energia e materiais auxiliares). A avaliação da qualidade de CDR produzido a partir do ensaio laboratorial representou também uma parte muito significativa do trabalho produzido. A avaliação ambiental foi efetuada com base na metodologia da Avaliação de Ciclo de Vida (ACV). Os resultados obtidos permitiram concluir que o processo da Recivalongo transforma 69% do material de entrada, recuperando 2% em metais ferrosos e rejeitando para aterro a restante fração de 29%. As análises efetuadas ao CDR mostraram que apresenta um PCI compreendido entre 17 e 20 MJ/kg; o teor em cloro está compreendido entre 0,2 e 0,8% Conclui-se que neste processo o parâmetro mais difícil de controlar é o teor em cloro no CDR, pois existe uma grande diversidade de resíduos com grandes quantidades de cloro na sua constituição e que por muitas vezes são difíceis de identificar e/ou separar na primeira fase do tratamento dos resíduos. Da análise ciclo de vida efetuada à produção de CDR pode-se afirmar que esta operação de gestão de resíduos apresenta uma mais-valia quando comparada com a deposição dos resíduos em aterro, não sendo a diferença entre destinos tão significativa quanto o esperado. Desta avaliação pode concluir-se que a instalação operou muito abaixo da sua capacidade, sendo esta considerada uma das melhores linhas de produção de CDR a nível nacional.

X-Ray powder diffraction laboratory @ University of Málaga (UMA)

X-Ray Powder Diffraction (XRPD) laboratory is a facility placed at Servicios Centrales de apoyo a la Investigación (SCAI) at University of Malaga (UMA) http://www.scai.uma.es/. This facility has three XRPD diffractometers and a diffractometer to measure high-resolution thin-films. X´Pert PRO MPD from PANalytical. This is a bragg-brentano (theta/2theta) with reflection geometry diffractometer which allows to obtain high resolution XRPD data with strictly monochromatic CuKα1 radiation (λ=1.54059Å) [Ge(111) primary monochromator] and an automatic sample charger. Moreover, it has parallel monochromatic CuKα1 radiation (λ=1.54059Å) with an hybrid Ge(220) monochromator for capillary and multiproposal (bulk samples up to 1 Kg) sample holders. The HTK1200N chamber from Anton Paar allows collecting high resolution high temperature patterns. EMPYREAN from PANalytical. This diffractometer works in reflection and transmission geometries with theta/theta goniometer, using CuKα1,2 radiation (λ=1.5418Å), a focusing X-ray mirror and a ultra-fast PIXCEL 3D detector with 1D and 2D collection data modes (microstructural and preferred orientation analysis). Moreover, the TTK450N chamber allows low temperature and up to 450ºC studies. A D8 ADVANCE (BRUKER) was installed in April 2014. It is the first diffractometer in Europe equipped with a Johansson Ge(111) primary monochromator, which gives a strictly monochromatic Mo radiation (λ=0.7093 Å) [1]. It works in transmission mode (with a sample charger) with this high resolution configuration. XRPD data suitable for PDF (Pair Distribution Function) analysis can be collected with a capillary sample holder, due to the high energy and high resolution capabilities of this diffractometer. Moreover, it has a humidity chamber MHC-trans from Anton Paar working on transmission mode with MoKα1 (measurements can be collected at 5 to 95% of relative humidity (from 20 to 80 ºC) and up to 150ºC [2]). Furthermore, this diffractometer also has a reaction chamber XRK900 from Anton Paar (which uses CuKα1,2 radiation in reflection mode), which allows data collection from room temperature to 900ºC with up to 10 bar of different gases. Finally, a D8 DISVOVER A25 from BRUKER was installed on December 2014. It has a five axis Euler cradler and optics devices suitable for high resolution thin film data collection collected in in-plane and out-of-plane modes. To sum up, high-resolution thin films, microstructural, rocking-curve, Small Angle X-ray Scattering (SAXS), Grazing incident SAXS (GISAXS), Ultra Grazing incident diffraction (Ultra-GID) and microdiffraction measurements can be performed with the appropriated optics and sample holders. [1] L. León-Reina, M. García-Maté, G. Álvarez-Pinazo, I. Santacruz, O. Vallcorba, A.G. De la Torre, M.A.G. Aranda “Accuracy in Rietveld quantitative phase analysis: a comparative study of strictly monochromatic Mo and Cu radiations” J. Appl. Crystallogr. 2016, 49, 722-735. [2] J. Aríñez-Soriano, J. Albalad, C. Vila-Parrondo, J. Pérez-Carvajal, S. Rodríguez-Hermida, A. Cabeza, F. Busqué, J. Juanhuix, I. Imaz, Daniel Maspoch “Single-crystal and humidity-controlled powder diffraction study of the breathing effect in a metal-organic framework upon water adsorption/desorption” Chem. Commun., 2016, DOI: 10.1039/C6CC02908F.

Predictive Value Of Phase I Trials For Safety In Later Trials And Final Approved Dose: Analysis Of 61 Approved Cancer Drugs.

Phase I trials use a small number of patients to define a maximum tolerated dose (MTD) and the safety of new agents. We compared data from phase I and registration trials to determine whether early trials predicted later safety and final dose. We searched the U.S. Food and Drug Administration (FDA) website for drugs approved in nonpediatric cancers (January 1990-October 2012). The recommended phase II dose (R2PD) and toxicities from phase I were compared with doses and safety in later trials. In 62 of 85 (73%) matched trials, the dose from the later trial was within 20% of the RP2D. In a multivariable analysis, phase I trials of targeted agents were less predictive of the final approved dose (OR, 0.2 for adopting ± 20% of the RP2D for targeted vs. other classes; P = 0.025). Of the 530 clinically relevant toxicities in later trials, 70% (n = 374) were described in phase I. A significant relationship (P = 0.0032) between increasing the number of patients in phase I (up to 60) and the ability to describe future clinically relevant toxicities was observed. Among 28,505 patients in later trials, the death rate that was related to drug was 1.41%. In conclusion, dosing based on phase I trials was associated with a low toxicity-related death rate in later trials. The ability to predict relevant toxicities correlates with the number of patients on the initial phase I trial. The final dose approved was within 20% of the RP2D in 73% of assessed trials.