Vinasse application to sugar cane fields. Effect on the unsaturated zone and groundwater at Valle del Cauca (Colombia)

Extensive application of vinasse, a subproduct from sugar cane plantations for bioethanol production, is currently taking place as a source of nutrients that forms part of agricultural management in different agroclimatic regions. Liquid vinasse composition is characterised by high variability of organic compounds and major ions, acid pH (4.7), high TDS concentration (117,416–599,400 mg L− 1) and elevated EC (14,350–64,099 μS cm− 1). A large-scale sugar cane field application is taking place in Valle del Cauca (Colombia), where monitoring of soil, unsaturated zone and the aquifer underneath has been made since 2006 to evaluate possible impacts on three experimental plots. For this assessment, monitoring wells and piezometers were installed to determine groundwater flow and water samples were collected for chemical analysis. In the unsaturated zone, tensiometers were installed at different depths to determine flow patterns, while suction lysimeters were used for water sample chemical determinations. The findings show that in the sandy loam plot (Hacienda Real), the unsaturated zone is characterised by low water retention, showing a high transport capacity, while the other two plots of silty composition presented temporal saturation due to La Niña event (2010–2011). The strong La Niña effect on aquifer recharge which would dilute the infiltrated water during the monitoring period and, on the other hand dissolution of possible precipitated salts bringing them back into solution may occur. A slight increase in the concentration of major ions was observed in groundwater (~ 5% of TDS), which can be attributed to a combination of factors: vinasse dilution produced by water input and hydrochemical processes along with nutrient removal produced by sugar cane uptake. This fact may make the aquifer vulnerable to contamination.

Robust multivariable control of complex biological processes

This paper addresses advanced control of a biological nutrient removal (BNR) activated sludge process. Based on a previously validated distributed parameter model of the BNR activated sludge process, we present robust multivariable controller designs for the process, involving loop shaping of plant model, robust stability and performance analyses. Results from three design case studies showed that a multivariable controller with stability margins of 0.163, 0.492 and 1.062 measured by the normalised coprime factor, multiplicative and additive uncertainties respectively give the best results for meeting performance robustness specifications. The controller robustly stabilises effluent nutrients in the presence of uncertainties with the behaviour of phosphorus accumulating organisms as well as to effectively attenuate major disturbances introduced as step changes. This study also shows that, performance of the multivariable robust controller is superior to multi-loops SISO PI controllers for regulating the BNR activated sludge process in terms of robust stability and performance and controlling the process using inlet feed flowrate is infeasible. (C) 2003 Elsevier Ltd. All rights reserved.

Microbial quantification in activated sludge: the hits and misses

Since the implementation of the activated sludge process for treating wastewater, there has been a reliance on chemical and physical parameters to monitor the system. However, in biological nutrient removal (BNR) processes, the microorganisms responsible for some of the transformations should be used to monitor the processes with the overall goal to achieve better treatment performance. The development of in situ identification and rapid quantification techniques for key microorganisms involved in BNR are required to achieve this goal. This study explored the quantification of Nitrospira, a key organism in the oxidation of nitrite to nitrate in BNR. Two molecular genetic microbial quantification techniques were evaluated: real-time polymerase chain reaction (PCR) and fluorescence in situ hybridisation (FISH) followed by digital image analysis. A correlation between the Nitrospira quantitative data and the nitrate production rate, determined in batch tests, was attempted. The disadvantages and advantages of both methods will be discussed.

Use of stable-isotope probing, full-cycle rRNA analysis, and fluorescence in situ hybridization-microautoradiography to study a methanol-fed denitrifying microbial community

A denitrifying microbial consortium was enriched in an anoxically operated, methanol-fed sequencing batch reactor (SBR) fed with a mineral salts medium containing methanol as the sole carbon source and nitrate as the electron acceptor. The SBR was inoculated with sludge from a biological nutrient removal activated sludge plant exhibiting good denitrification. The SBR denitrification rate improved from less than 0.02 mg of NO3-.N mg of mixed-liquor volatile suspended solids (MLVSS)(-1) h(-1) to a steady-state value of 0.06 mg of NO3-.N mg of MLVSS-1 h(-1) over a 7-month operational period. At this time, the enriched microbial community was subjected to stable-isotope probing (SIP) with [C-13] methanol to biomark the DNA of the denitrifiers. The extracted [C-13]DNA and [C-12]DNA from the SIP experiment were separately subjected to full-cycle rRNA analysis. The dominant 16S rRNA gene phylotype (group A clones) in the [C-13]DNA clone library was closely related to those of the obligate methylotrophs Methylobacillus and Methylophilus in the order Methylophilales of the Betaproteobacteria (96 to 97% sequence identities), while the most abundant clone groups in the [C-12]DNA clone library mostly belonged to the family Saprospiraceae in the Bacteroidetes phylum. Oligonucleotide probes for use in fluorescence in situ hybridization (FISH) were designed to specifically target the group A clones and Methylophilales (probes DEN67 and MET1216, respectively) and the Saprospiraceae clones (probe SAP553). Application of these probes to the SBR biomass over the enrichment period demonstrated a strong correlation between the level of SBR denitrification and relative abundance of DEN67-targeted bacteria in the SBR community. By contrast, there was no correlation between the denitrification rate and the relative abundances of the well-known denitrifying genera Hyphomicrobium and Paracoccus or the Saprospiraceae clones visualized by FISH in the SBR biomass. FISH combined with microautoradiography independently confirmed that the DEN67-targeted cells were the dominant bacterial group capable of anoxic [C-14] methanol uptake in the enriched biomass. The well-known denitrification lag period in the methanol-fed SBR was shown to coincide with a lag phase in growth of the DEN67-targeted denitrifying population. We conclude that Methylophilales bacteria are the dominant denitrifiers in our SBR system and likely are important denitrifiers in full-scale methanol-fed denitrifying sludges.

Advances in distributed parameter approach to the dynamics and control of activated sludge processes for wastewater treatment

This paper presents a review of modelling and control of biological nutrient removal (BNR)-activated sludge processes for wastewater treatment using distributed parameter models described by partial differential equations (PDE). Numerical methods for solution to the BNR-activated sludge process dynamics are reviewed and these include method of lines, global orthogonal collocation and orthogonal collocation on finite elements. Fundamental techniques and conceptual advances of the distributed parameter approach to the dynamics and control of activated sludge processes are briefly described. A critical analysis on the advantages of the distributed parameter approach over the conventional modelling strategy in this paper shows that the activated sludge process is more adequately described by the former and the method is recommended for application to the wastewater industry (c) 2006 Elsevier Ltd. All rights reserved.

Valoração do efluente da indústria processadora de pescado por incorporação de nutrientes em aphanothece microscopica nägeli

Nesta tese procurou-se demonstrar a valoração do efluente do processamento de pescado por incorporação dos nutrientes em Aphanothece microscopica Nägeli a diferentes temperaturas. Para tanto o trabalho é composto de cinco artigos que objetivaram avaliar sob o ponto de vista do tratamento do efluente pela cianobactéria Aphanothece e a separação e avaliação da biomassa gerada. O primeiro artigo intitula-se “Influência da temperatura na remoção de nutrientes do efluente da indústria de pescado por Aphanothece microscopica Nägeli”, e teve por objetivo avaliar a influência da temperatura (10, 20 e 30ºC) em um sistema de tratamento pela cianobactéria Aphanothece na remoção de matéria orgânica, nitrogênio e fósforo do efluente oriundo do processamento de pescado. A análise dos resultados mostrou que a temperatura influenciou significativamente na remoção de DQO, NTK, N-NH4 + e P-PO4 -3 . Para os experimentos a 20 e 30ºC todos os limites estabelecidos para os parâmetros avaliados foram atingidos. O segundo artigo intitulado “Efeito de coagulantes no efluente da indústria da pesca visando à separação de biomassa quando tratado por cianobactéria” avaliou o efeito da concentração e pH de dois tipos de coagulantes, cloreto férrico (FeCl3) e sulfato de alumínio (Al2(SO4)3), na separação da biomassa da cianobactéria Aphanothece microscopica Nägeli cultivada em efluente da indústria da pesca, assim como a remoção de matéria orgânica e nutrientes do efluente. Os resultados indicaram que o coagulante FeCl3 foi mais eficaz na remoção de todos os parâmetros testados. No que concerne à separação da biomassa, com um número de seis lavagens foi removido cerca de 97,6% da concentração de FeCl3 adicionado inicialmente. O terceiro artigo com o título “Caracterização da biomassa de Aphanothece microscopica Nägeli gerada no efluente da indústria da pesca em diferentes temperaturas de cultivo” avaliou a composição química da biomassa da cianobactéria Aphanothece microscopica Nägeli quando desenvolvida em meio de cultivo padrão BG11 e no efluente do processamento de pescado. O quarto artigo teve como título “Influência do meio de cultivo e temperatura em compostos nitrogenados na cianobactéria Aphanothece microscopica Nägeli” objetivou avaliar o teor de compostos nitrogenados presentes na biomassa da cianobactéria Aphanothece microscopica Nägeli quando cultivada em meio padrão e no efluente da indústria da pesca nas diferentes fases de crescimento. Para o estudo da composição química e nitrogenados no efluente foram realizados experimentos nas temperaturas de 10, 20 e 30ºC. As concentrações de proteína, cinzas e pigmentos aumentaram com o aumento da temperatura. Por outro lado, foi observada uma redução do teor de lipídios e carboidratos com o aumento da temperatura. O íon amônio juntamente com os ácidos nucléicos representa uma importante fração do nitrogênio não protéico presente na biomassa da cianobactéria Aphanothece. Ficou demonstrada a influência do meio de cultivo na concentração de nitrogênio, bem como a determinação de proteína pelo método de Kjeldahl superestima a concentração protéica em cianobactérias. O quinto artigo intitulado “Produção de proteína unicelular a partir do efluente do processamento do pescado: modelagem preditiva e simulação” avaliou a produção de proteína unicelular através do cultivo da cianobactéria Aphanothece microscopica Nägeli no efluente da indústria da pesca. Os dados cinéticos de crescimento celular foram ajustados a quatro modelos matemáticos (Logístico, Gompertz, Gompertz Modificado e Baranyi). Os resultados demonstraram que o modelo Logístico foi considerado o mais adequado para descrever a formação de biomassa. A análise preditiva mostrou a possibilidade da obtenção de 1,66, 18,96 e 57,36 kg.m-3.d-1 de biomassa por volume do reator em 1000 h de processo contínuo, para as temperaturas de 10, 20 e 30ºC, respectivamente.

Dinâmica do fósforo em cultivo heterotrófico e produção de compostos celulares por cianobactéria integrado a biorrefinarias agroindustriais

O objetivo desta tese foi avaliar a dinâmica do fósforo em cultivo heterotrófico e produção de compostos celulares por Aphanothece microscopica Nägeli visando avaliar a perspectiva de implementação de uma biorrefinaria microalgal. Desta forma, foi avaliado o comportamento do micro-organismo em estudo no cultivo heterotrófico, utilizando como meio de cultivo o efluente de laticínios. O trabalho foi desenvolvido em 3 etapas. Em um primeiro momento foi avaliada a influência da temperatura (20 e 30°C) e os valores máximos e mínimos de nutrientes, em especial do fósforo dissolvido reativo (PDR), disponíveis no efluente de laticínio, na remoção de nutrientes. Os resultados demonstraram que a concentração inicial de fósforo dissolvido e a temperatura exerceram influência no crescimento celular e na eficiência de remoção de nutrientes. Em termos de otimização de processo os cultivos conduzidos a 20°C e maiores concentrações de PDR (5,5 mg.L-1 ) no efluente de laticínio, foram os mais eficientes na conversão de poluentes em biomassa e remoção de nutrientes. A segunda etapa foi desenvolvida com o objetivo de avaliar a dinâmica de distribuição de fósforo na fase líquida e sólida do reator heterotrófico, quando o efluente de laticínio foi tratado pela Aphanothece microscopica Nägeli, a 20°C e nas máximas concentrações de fósforo dissolvido encontradas no efluente. Foi demonstrado que as formas fosforadas na fase líquida do reator se caracterizam pela predominância da fração dissolvida em comparação à particulada e por apresentar como fração predominante a de fósforo orgânico. No que se refere à fase sólida, ficou demonstrado que a Aphanothece microscopica Nägeli, quando cultivada heterotroficamente apresenta 3,8 vezes mais fósforo que o requerido para o crescimento celular. Ficando demonstrado ainda que a remoção biológica de fósforo por Aphanothece microscopica Nägeli pode resultar em substanciais aportes financeiros para as estações de tratamento de efluentes. Uma terceira etapa foi desenvolvida, a qual teve como objetivo avaliar a estimativa de produção de compostos celulares por Aphanothece microscopica Nägeli, a partir do efluente de laticínio, bem como o efeito da redução de temperatura de cultivo no teor de lipídios , no momento em que é obtida a máxima concentração deste componente celular, nas condições otimizadas.Foi obtido na fase logarítmica de crescimento, concentrações de 41,8 % de proteinas, carboidratos 28,5 %, lipídios 10,4 % e minerais 10,8 %. O maior teor de lipídio registrado a 20°C correspondeu a biomassa analisada na fase logarítmica.Com a redução da temperatura para 5°C por um período de 30 h é possível obter concentrações de lipídios 2,4 vezes superior ao registrado na fase logarítmica a 20 °C. No entanto, não foram indicadas diferenças significativas (p≤0,05) em função da temperatura entre as concentrações de lipídios obtidas para a biomassa a 10°C em 40 h. O perfil de ácidos graxos da biomassa gerada a 20°C, apresentou como ácidos graxos majoritários, os ácidos graxos: palmítico, oléico, γ-linolênico, palmitoleico e esteárico, resultando um aumento na concentração de ácidos graxos saturados as espensa dos insaturados, quando a temperatura é reduzida. Em paralelo,um reator heterotrófico descontinuo foi definido, ficando demonstrado que a extrapolação da operação em batelada para contínua requer um biorreator heterotrófico com volume útil de trabalho de 240,51 m 3 , permitindo tratar 950 m3 diários de efluente, gerando 11,8 kg.d-1 de biomassa útil para produção de compostos celulares por Aphanothece microscopica Nägeli, visando à simultânea remoção de matéria orgânica, nitrogênio total e fósforo total, gerando insumos que podem suportar a implementação de uma biorrefinaria microalgal.

Mapping spatial and temporal potassium balances in Brazilian soils of south-west Goias.

Introduction: Brazil, is one of the main agricultural producers in the world ranking 1st in the production of sugarcane, coffee and oranges. It is also 2nd as world producer of soybeans and a leader in the harvested yields of many other crops. The annual consumption of mineral fertilizers exceeds 20 million mt, 30% of which corresponds to potash fertilizers (ANDA, 2006). From this statistic it may be supposed that fertilizer application in Brazil is rather high, compared with many other countries. However, even if it is assumed that only one fourth of this enormous 8.5 million km2 territory is used for agriculture, average levels of fertilizer application per hectare of arable land are not high enough for sustainable production. One of the major constraints is the relatively low natural fertility status of the soils which contain excessive Fe and Al oxides. Agriculture is also often practised on sandy soils so that the heavy rainfall causes large losses of nutrients through leaching. In general, nutrient removal by crops such as sugarcane and tropical fruits is much more than the average nutrient application via fertilization, especially in regions with a long history of agricultural production. In the recently developed areas, especially in the Cerrado (Brazilian savanna) where agriculture has expanded since 1980, soils are even poorer than in the "old" agricultural regions, and high costs of mineral fertilizers have become a significant input factor in determining soybean, maize and cotton planting. The consumption of mineral fertilizers throughout Brazil is very uneven. According to the 1995/96 Agricultural Census, only in eight of the total of 26 Brazilian states, were 50 per cent or more of the farms treated "systematically" with mineral fertilizers; in many states it was less than 25 per cent, and in five states even less than 12 per cent (Brazilian Institute for Geography and Statistics; Censo Agropecuario1995/96, Instituto Brazileiro de Geografia e Estadistica; IBGE, www.ibge.gov.br). The geographical application distribution pattern of mineral fertilizers may be considered as an important field of research. Understanding geographical disparities in fertilization level requires a complex approach. This includes evaluation of the availability of nutrients in the soil (and related soil properties e.g. CEC and texture), the input of nutrients with fertilizer application, and the removal of nutrients by harvested yields. When all these data are compiled, it is possible to evaluate the balance of particular nutrients for certain areas, and make conclusions as to where agricultural practices should be optimized. This kind of research is somewhat complicated, because it relies on completely different sources of data, usually from incomparable data sources, e.g. soil characteristics attributed to soil type areas, in contrast to yields by administrative regions, or farms. A priority tool in this case is the Geographical Information System (GIS), which enables attribution of data from different fields to the same territorial units, and makes possible integration of these data in an "inputoutput" model, where "input" is the natural availability of a nutrient in the soil plus fertilization, and "output" export of the same nutrient with the removed harvested yield.

Understanding nutrient build-up on urban road surfaces

This paper discusses the outcomes of a research project on nutrients build-up on urban road surfaces. Nutrient build-up was investigated on road sites belonging to residential, industrial and commercial land use. Collected build-up samples were separated into five particle size ranges and were tested for total nitrogen (TN), total phosphorus (TP) and sub species of nutrients, namely, NO2-, NO3-, TKN and PO43-. Multivariate analytical techniques were used to analyse the data and to develop detailed understanding on build-up. Data analysis revealed that the solids loads on urban road surfaces are highly influenced by factors such as land use, antecedent dry period and traffic volume. However, the nutrient build-up process was found to be independent of the type of land use. It was solely dependent on the particle size of solids build-up. Most of the nutrients were associated with the particle size range <150 μm. Therefore, the removal of particles below 150 µm from road surfaces is of importance for the removal of nitrogen and phosphorus from road surface solids build-up. It is also important to consider the differences in the composition of nitrogen and phosphorus build-up in the context of designing effective stormwater quality mitigation strategies.

Significance of drying periods on nitrate removal in experimental biofilters

Nitrogen is an important nutrient that can impact the quality of aquatic environments when present in high concentration. Even though low concentration levels of ammonium-nitrogen have been observed in laboratory studies in bioretention basins, poor removal or even the production of nitrate-nitrogen within the filter is often recorded in such studies. Ten Perspex biofilter columns of 94 mm (internal diameter) were packed with a filter layer, transition layer and a gravel layer. While the filter layer was packed to a height of 800 mm, transition and gravel layers were packed to a composite height of 220 mm and operated with simulated stormwater in the laboratory. The filter layer contained 8% organic material by weight. A free board of 350 mm provided detention storage and head to facilitate infiltration. The columns were operated with different antecedent dry days (0 d to 21 d) and constant inflow concentration at a feed rate of 100 mL/min. Samples were collected from the outflow at different time intervals, between 2 min and 150 min from the start of outflow, and were tested for nitrate-nitrogen and total organic carbon. Washoff of organic carbon from the filter layer was observed to occur for 30 min of outflow. This indicated washoff of organic carbon from the filter itself. At the same time, a very low concentration of nitrate-nitrogen was recorded at the beginning of the outflow, indicating the effective removal of nitrate-nitrogen. We conclude that the removal of nitrate-nitrogen is insignificant during the wetting phase of a rainfall event and the process of denitrification is more pronounced during the drying phase of a rainfall event. Thus intermittent wetting and drying is crucial for the removal of nitrate-nitrogen in bioretention basins.

Effects of secondary crops on bacterial growth and nitrogen removal in shrimp farm effluent treatment systems

Secondary crops provide a means of assimilating some effluent nitrogen from eutrophic shrimp farm settlement ponds. However, a more important role may be their stimulation of beneficial bacterial nitrogen removal processes. In this study, bacterial biomass, growth and nitrogen removal capacity were quantified in shrimp farm effluent treatment systems containing vertical artificial substrates and either the banana shrimp Penaeus merguiensis (de Man) or the grey mullet, Mugil cephalus L. Banana shrimp were found to actively graze biofilm on the artificial substrates and significantly reduced bacterial biomass relative to a control (24.5 ± 5.6mgCm−2 and 39.2 ± 8.7mgCm−2, respectively). Bacterial volumetric growth rates, however, were significantly increased in the presence of the shrimp relative to the control 45.2±11.3mgCm−2 per day and 22.0±4.3mgCm−2 per day, respectively). Specific growth rate, or growth rate per cell, of bacteria was therefore appreciably stimulated by the banana shrimp. Nitrate assimilation was found to be significantly higher on grazed substrate biofilm relative to the control (223±54 mgNm−2 per day and 126±36 mg Nm−2 per day, respectively), suggesting that increased bacterial growth rate does relate to enhanced nitrogen uptake. Regulated banana shrimp feeding activity therefore can increase the rate of newbacterial biomass production and also the capacity for bacterial effluent nitrogen assimilation. Mullet had a negligible influence on the biofilm associated with the artificial substrate but reduced sediment bacterial biomass (224 ± 92 mgCm−2) relative to undisturbed sediment (650 ± 254 mgCm−2). Net, or volumetric bacterial growth in the sediment was similar in treatments with and without mullet, suggesting that the growth rate per cell of bacteria in grazed sediments was enhanced. Similar rates of dissolved nitrogen mineralisation werefound in sediments with and without mullet but nitrificationwas reduced. Presence of mullet increased water column suspended solids concentrations, water column bacterial growth and dissolved nutrient uptake. This study has shown that secondary crops, particularly banana shrimp, can play a stimulatory role in the bacterial processing of effluent nitrogen in eutrophic shrimp effluent treatment systems.

Testing the effectiveness of the SKIM foam fractionator to reduce nutrient levels in prawn farm effluent

To experimentally investigate the effect of the “SKIM” mechanical foam fractionator on suspended material and the nutrient levels in prawn farm effluent, a series of standardised short-term treatments were applied to various effluent types in a static 10,000-litre water body. Prawn pond effluents were characterised by watercolour and dominance of phytoplankton species. Three effluent types were tested, namely 1) particulate-rich effluent with little apparent phytoplankton, 2) green mircoalgal bloom predominately made up of single celled phytoplankton, and 3) brown microalgal bloom with higher prevalence of diatoms. The effluent types were similar (P>0.05) in non-volatile particulate material, and nitrate/nitrite but varied from each other in the following ways: 1) The particulate-rich effluents were lower (P<0.05) in volatile solids (compared to brown blooms), total Kjeldahl nitrogen, dissolved organic nitrogen, dissolved organic phosphorus and chlorophyll a (compared to both green and brown blooms). 2) The brown blooms were higher (P<0.05) in ammonia (compared to green blooms), total nitrogen and total phosphorus (compared to both green and particulate-rich effluent), but were lower (P<0.05) in inorganic phosphorus (compared to both green and particulate-rich effluent). 3) The green blooms were higher (P<0.05) in dissolved (both organic and inorganic) phosphorus (compared to both brown and particulate-rich effluents). Although the effluent types varied significantly in these aspects the effect of the Skim treatment was similar for all parameters measured except total phosphorus. Bloom type and Skim-treatment period significantly (P<0.05) affected total Kjeldahl phosphorus concentrations. For all effluent types there was a continuous significant reduction (P<0.05) in total Kjeldahl phosphorus during the initial 6-hour treatment period. Levels of total suspended solids and volatile suspended solids in all effluent types were significantly (P<0.05) reduced in the first 2 hours but not thereafter. Non-volatile suspended solids were also significantly (P<0.05) reduced in the first 2 hours (30 to 40 % reduction) and a further 40% reduction occurred in the particulate-rich effluent over the next 2 hours. Mean values for total ammonia, dissolved organic nitrogen, total Kjeldahl nitrogen, total nitrogen, chlorophyll a and dissolved organic or inorganic phosphorus levels were not significantly (P>0.05) affected by the Skim unit in any bloom type during the initial 6 hours of testing. Nevertheless, non-significant nitrogen reductions did occur. Foam production by the Skim unit varied with different blooms, resulting in different concentrate volumes and different end points for separate experiments. Concentrate volumes were generally high for the particulate-rich and green blooms (175 – 370 litres) and low for the brown blooms (25 – 80 litres). This was due to the low tendency of the brown bloom to produce foam. This generated higher nutrient concentrations in the associated condensed foam, but may have limited the treatment efficiency. The results suggest that in this application, the Skim unit did not remove micro-algae as effectively as was anticipated. However, it was effective at removing other suspended solids. Considering these attributes and the other uses of this machinery documented by the manufactures, the unit’s oxygenation mixing capacities coupled with inorganic solids removal may provide a suitable mechanism for construction of a continuously mixed bioreactor that utilises the filtration and profit making abilities of bivalves.

Defining critical soil nutrient concentrations in soils supporting grains and cotton in Northern NSW and Queensland

This project focussed on the phosphorus (P) and potassium (K) status of northern cropping soils. Stores of P and K have been depleted by crop removal and limited fertiliser application, with depletion most significant in the subsoil. Soil testing strategies are confounded by slowly available mineral reserves with uncertain availability. The utility of new soil tests was assessed to measure these reserves, their availability to plants quantified and a regional sampling strategy undertaken to identify areas of greatest P and K deficit. Fertiliser application strategies for P and K have been tested and the interactions between these and other nutrients have been determined in a large field program.

Nutrient Distributions In An Estuary - Evidence Of Chemical Precipitation Of Dissolved Silicate And Phosphate

Continuous autoanalytical recordings of the axial distributions of dissolved nitrate, silicate and phosphate in the influent freshwater and saline waters of the Tamar Estuary, south-west England have been obtained. Short-term variability in the distributions was assessed by repetitive profiling at approximately 3-h intervals on a single day and seasonal comparisons were obtained from ten surveys carried out between June 1977 and August 1978. Whereas nitrate is always essentially conserved throughout the upper estuary, the silicate- and phosphate-salinity relationships consistently indicate a non-biological removal of these nutrients within the low (0–10%) salinity range. Attempts to quantify precisely the degree of removal and to correlate this with changes in environmental properties (pH, turbidity, chlorophyll fluorescence, salinity, freshwater composition) were mainly inconclusive due to short-term fluctuations in the riverine concentrations of silicate and phosphate advected into the reactive region and to the rapid changes in turbidity brought about by tidally-induced resuspension and deposition of bottom sediment.