A New Modular Marx Derived Multilevel Converter

A new Modular Marx Multilevel Converter, M(3)C, is presented. The M(3)C topology was developed based on the Marx Generator concept and can contribute to technological innovation for sustainability by enabling wind energy off-shore modular multilevel power switching converters with an arbitrary number of levels. This paper solves both the DC capacitor voltage balancing problem and modularity problems of multilevel converters, using a modified cell of a solid-state Marx modulator, previously developed by authors for high voltage pulsed power applications. The paper details the structure and operation of the M(3)C modules, and their assembling to obtain multilevel converters. Sliding mode control is applied to a M(3)C leg and the vector leading to automatic capacitor voltage equalization is chosen. Simulation results are presented to show the effectiveness of the proposed M(3)C topology.

Affordable prefabricated modular houses using cement and polymer based materials and advanced design tools

By taking advantage of the appropriate use of cement and polymer based materials and advanced computational tools, a pre-fabricated affordable house was built in a modular system. Modular system refers to the complete structure that is built-up by assembling pre-fabricated sandwich panels composed of steel fibre reinforced self-compacting concrete (SFRSCC) outer layers that are connected by innovative glass fibre reinforced polymer (GFRP) connectors, resulting in a panel with adequate structural, acoustic, and thermal insulation properties. The modular house was prepared for a typical family of six members, but its living area can be easily increased by assembling other pre-fabricated elements. The speed of construction and the cost of the constructive elements make these houses competitive when compared to traditional solutions. In this paper the relevant research subjacent to this project (LEGOUSE) is briefly described, as well as the construction process of the built real scale prototype.

Disseny i implementació d'un web modular amb gestió de continguts

Aquest projecte té com a objectiu el desenvolupament d'un site web amb la possibilitat que la gestió del seu contingut fos administrat per persones alienes a la implementació de la web. Aquesta fita ha estat duta a terme en una web d'una entitat esportiva, la Unió Esportiva Sant Cugat, des d'on durant 2 anys i mig s'ha gestionat la informació i comunicació a través de la xarxa amb aquest mitjà. L'estructuració del projecte ha estat totalment modular, per d'aquesta manera facilitar el dinamisme de canvis de possibles continguts que es poden incorporar a la web de manera molt ràpida i senzilla.

Animal Tissue Response To Mid-Term Electronic Modular Artificial Sphincter Implantation

Introduction and objectives: The AMS 800TM is considered the gold standard for sphincter replacement. However, the one-ring design can erode the urethra and lead to severe complications. A mechanism that could alternatively compress successive segments of the urethra would limit such deleterious outcome. We report 12 weeks animal urethral tissue analysis following implantation of a new modular artificial sphincter. METHODS: The device is composed by three parts: the contractile unit, two rings and an integrated microprocessor. The contractile unit is made of Nitinol fibers. The rings are placed around the urethra to control the flow of urine by squeezing the urethra. They work in a sequential alternative mode and are controlled by a microprocessor connected to an external computer. The computer can reveal specific failure of device components. The device was impkanted in eight male sheep. The rings were positioned around the urethra and the control unit was placed 5cm away. The device was working twenty hours per day; it was open 10min. per hour to allow urination. The animals were sacrificed after 12 weeks. The urethra and the tissues surrounding the control unit were macroscopically and microscopically examined. Two transversal sections crossing the sphincter and two transversal sections crossing the urethra alone were obtained and stained with modified Paragon after resin embedding. Urethra was also embedded in paraffin. The first section was stained with safranin-hematoxylin-eosin, the second section was stained with Masson's Trichrome and the remaining eight sections were available for immunolabelling of the macrophages.Results: The chronic study went uneventful. No clinical infection or pain was observed. The computer registered no specific failure in ring function, Nitinol wires and tube connectors. At explantation, except for a slight grade of lymphocytes in two out of eight specimens, no urethral stricture or atrophy could be observed. Immunohistochemistry confirmed the absence of macrophages. Tissue structure and organization of the urethra with and without artificial sphincter were similar. No migration of the device was observed.Conclusions: The study clearly showed no tissue damage or inflammation of the urethra. Electronic design, preservation of urethral vascularisation and adjustability after implantation are the key ideas to improve the actual AUS. Further studies will be carried out to evaluate this potential.

Harmonising the Modular Product Range

Työn tavoitteena on analysoida KONEen hissien ovituoteperheitä ja harmonisoida modulaarista ovituotevalikoimaa niin, että tulos olisi mahdollisimman suotuisa KONEelle sekä sen sidosryhmille. Harmonisointi toteutetaan, koska KONEen tuotevalikoima on erittäin laaja ja monimutkainen ja siitä syystä erittäin kallis ja vaikea hallita ja ylläpitää. Tavoitteena on selvittää myös termejä modulaarisuus ja tuotealusta olennaisen kirjallisuuden pohjalta. Nykyään yritysten täytyy kehittää tuotevalikoimaa jatkuvasti. Yrityksen koko tuotevalikoiman varioituvuus tulisi kuitenkin pitää järkevissä rajoissa. Moduuleita ja tuotealustoja pitäisi käyttää jakamaan tuotteiden avainelementtejä ja lisäämään varioituvuutta helposti hallittavalla tavalla. Kannattamattomat ja matalavolyymiset tuotteet kuluttavat yrityksen niukkoja resursseja. Tällaiset tuotteet tulisi poistaa tuotevalikoimasta, mutta ei ilman harkintaa. Kannattama-tonkin tuote voi olla erittäin arvokas asiakkaalle ja tällaisen tuotteen hylkääminen voi olla yritykselle pitkällä tähtäimellä erittäin kohtalokasta. Työn tuloksena oli harmonisointiehdotus KONEen AMD-oville ja selvitys harmonisoinnin vaikutuksista. Harmonisointi KONEella päätettiin toteuttaa siten, että matalavolyymiset tuotteet siirrettiin erikoistuotteiden valikoimaan. Myös kustannusanalyysi tukee harmonisointipäätöstä laskentajärjestelmän puutteista huolimatta.

Service product structure supported by remote diagnostics

Työn tavoitteena oli määrittää etähuoltokonseptin yleinen rakenne sekä selvittää asiakkaille tarjottavia modulaarisia palvelutuotteita. Aluksi selvitettiin huoltokonseptin rakennetta kirjallisuuden ja asiantuntijoiden haastattelujen avulla. Asiantuntijoiden haastattelut toteutettiin vapaamuotoisesti kysymyslistaa apuna käyttäen. Tämän lisäksi työssä pohditaan KM, CRM ja PDM rooleja etähuoltokonseptin kannalta sekä tutkaillaan etähuollon tulevaisuuden näkymiä.Diplomityössä käsitellään modulaarisuutta yleisellä tasolla. Moduularisuus on moniulotteinen termi. Usein sillä tarkoitetaan yrityksen sisäistä tuotekehityksen hallintaa. Toisaalta se voidaan nähdä myös asiakkaalle tarjottavina tuotteina ja tässä diplomityössä on keskitytty tähän puoleen. Loppuosa diplomityöstä käsittelee palvelutuotteiden tuotteistamisprosessia.Diplomityön tuloksena hahmoteltiin etähuolto konseptia ja tutkittiin mahdollisia palvelutuotteita, joita voidaan sisällyttää etähuoltokonseptiin. Tämän lisäksi toteutettiin osa tuotteistamisprosessista. Etähuollon kehittäminen on haasteellista. Haasteeksi jää tuotekehitystoiminnan ja palvelupuolen toiminnan tehostaminen, jotta tuotteita voitaisiin jo suunnittelupuolella kehittää etähuollon tarpeisiin. Kehittäminen vaatii molempien puolien aktiivista osallistumista.

The modular forming press for paperboard packages

In this master’s thesis the structural and functional features of a forming tool are developed to meet the needs of modern packaging production for paperboard packaging are studied. The goal of the study is to develop a new type of machine for the manufacture of the paperboard package by pressing. In the structure of the developed forming press the possibility to modify the packaging as well as the requirements of industrial production, food hygiene and other operational matters are accounted for. The press has been sized based on the main dimensions of a single food-grade paperboard tray. In the LUT Packaging Laboratory the forming press is designed suitable for on-line operation. In addition, suggestions for further development of packaging line and equipment have been made based on the information gathered during this thesis study.

Cost estimation framework for modular product

Cost estimation is an important, but challenging process when designing a new product or a feature of it, verifying the product prices given by suppliers or planning a cost saving actions of existing products. It is even more challenging when the product is highly modular, not a bulk product. In general, cost estimation techniques can be divided into two main groups - qualitative and quantitative techniques - which can further be classified into more detailed methods. Generally, qualitative techniques are preferable when comparing alternatives and quantitative techniques when cost relationships can be found. The main objective of this thesis was to develop a method on how to estimate costs of internally manufactured and commercial elevator landing doors. Because of the challenging product structure, the proposed cost estimation framework is developed under three different levels based on past cost information available. The framework consists of features from both qualitative and quantitative cost estimation techniques. The starting point for the whole cost estimation process is an unambiguous, hierarchical product structure so that the product can be classified into controllable parts and is then easier to handle. Those controllable parts can then be compared to existing past cost knowledge of similar parts and create as accurate cost estimates as possible by that way.

Development of experimental structure and influence of high CO2 concentration in maize cro

Maize is a C4 plant that shows few or no response to high [CO2]. Thus, this study aimed to analyze the photosynthetic rate and yield of maize under high [CO2] and develop open-top chambers (OTC) to create an atmosphere enriched with CO2. The experiment was conducted between October 2008 and March 2009. The OTCs were developed in modular scheme. Measurement of photosynthetic rates, transpiration, stomata conductance, grain yield and dry matter were performed. The experimental design was randomized blocks with four replications and three treatments: P1 - plants grown in OTC with 700 ppm [CO2], P2 - plants grown in OTC with environmental [CO2], and P3 - control, cultivated in open field. The results were analyzed by ANOVA and Tukey's test (Pr< 0.05). The chambers can reduce by 25% the photosynthetically active radiation and increase the air and leaf temperatures. Plants under high [CO2] (P1) showed the highest photosynthetic rates and the lowest stomata conductance and transpiration. The total weight of grains (g) and dry mass of shoots (g) showed no increases for P1, despite their higher photosynthetic rates.

Design structure matrix ja sen hyödyntäminen ohjelmistotuotannossa

Työn tarkoituksena on selvittää, miten DSM ja siihen liittyvät analyysit toimivat. Työssä selvitetään myös, miten DSM:a voidaan hyödyntää tuotekehityksessä ja ohjelmistotuotannon kohtaamissa ongelmissa. DSM-neliömatriisiin sijoitetaan tarkasteltavan kohteen osat riveihin ja kolumneihin identtisessä järjestyksessä. Matriisin soluihin merkitään osien väliset riippuvuudet, joilla selvitetään kunkin osan lähettämä ja vastaanottama data suhteessa muihin osiin. DSM-analyysissa osien järjestystä muutetaan suoritus- tai toteutusjärjestyksen mukaisesti parhaaseen järjestykseen. Osat ryhmitellään moduuleihin, jolloin esimerkiksi tuotekehitys ohjautuu automaattisesti modulaarisuuteen. Tuotekehitysprojekteihin DSM on kompaktin muodon, yksinkertaisuuden ja automaattisen järjestelyn ansiosta erinomainen työkalu, jolla voidaan mallintaa käytännössä mitä tahansa, mikä voidaan jakaa toisistaan riippuviin osiin. DSM voi vähentää projektien suunnitteluun vaadittua työmäärää ja avustaa realististen budjettien ja aikataulujen luontia suurissa projekteissa.

Glutamate receptors as seen by light: spectroscopic studies of structure-function relationships

Ionotropic glutamate receptors are major excitatory receptors in the central nervous system and also have a far reaching influence in other areas of the body. Their modular nature has allowed for the isolation of the ligand-binding domain and for subsequent structural studies using a variety of spectroscopic techniques. This review will discuss the role of specific ligand:protein interactions in mediating activation in the a-amino-3-hydroxy-5-methyl-4-isoxazolepropionic acid subtype of glutamate receptors as established by various spectroscopic investigations of the GluR2 and GluR4 subunits of this receptor. Specifically, this review will provide an introduction to the insight gained from X-ray crystallography and nuclear magnetic resonance investigations and then go on to focus on studies utilizing vibrational spectroscopy and fluorescence resonance energy transfer to study the behavior of the isolated ligand-binding domain in solution and discuss the importance of specific ligand:protein interactions in the mechanism of receptor activation.

Dynamic Facility Location with Modular Capacities : Models, Algorithms and Applications in Forestry

Les décisions de localisation sont souvent soumises à des aspects dynamiques comme des changements dans la demande des clients. Pour y répondre, la solution consiste à considérer une flexibilité accrue concernant l’emplacement et la capacité des installations. Même lorsque la demande est prévisible, trouver le planning optimal pour le déploiement et l'ajustement dynamique des capacités reste un défi. Dans cette thèse, nous nous concentrons sur des problèmes de localisation avec périodes multiples, et permettant l'ajustement dynamique des capacités, en particulier ceux avec des structures de coûts complexes. Nous étudions ces problèmes sous différents points de vue de recherche opérationnelle, en présentant et en comparant plusieurs modèles de programmation linéaire en nombres entiers (PLNE), l'évaluation de leur utilisation dans la pratique et en développant des algorithmes de résolution efficaces. Cette thèse est divisée en quatre parties. Tout d’abord, nous présentons le contexte industriel à l’origine de nos travaux: une compagnie forestière qui a besoin de localiser des campements pour accueillir les travailleurs forestiers. Nous présentons un modèle PLNE permettant la construction de nouveaux campements, l’extension, le déplacement et la fermeture temporaire partielle des campements existants. Ce modèle utilise des contraintes de capacité particulières, ainsi qu’une structure de coût à économie d’échelle sur plusieurs niveaux. L'utilité du modèle est évaluée par deux études de cas. La deuxième partie introduit le problème dynamique de localisation avec des capacités modulaires généralisées. Le modèle généralise plusieurs problèmes dynamiques de localisation et fournit de meilleures bornes de la relaxation linéaire que leurs formulations spécialisées. Le modèle peut résoudre des problèmes de localisation où les coûts pour les changements de capacité sont définis pour toutes les paires de niveaux de capacité, comme c'est le cas dans le problème industriel mentionnée ci-dessus. Il est appliqué à trois cas particuliers: l'expansion et la réduction des capacités, la fermeture temporaire des installations, et la combinaison des deux. Nous démontrons des relations de dominance entre notre formulation et les modèles existants pour les cas particuliers. Des expériences de calcul sur un grand nombre d’instances générées aléatoirement jusqu’à 100 installations et 1000 clients, montrent que notre modèle peut obtenir des solutions optimales plus rapidement que les formulations spécialisées existantes. Compte tenu de la complexité des modèles précédents pour les grandes instances, la troisième partie de la thèse propose des heuristiques lagrangiennes. Basées sur les méthodes du sous-gradient et des faisceaux, elles trouvent des solutions de bonne qualité même pour les instances de grande taille comportant jusqu’à 250 installations et 1000 clients. Nous améliorons ensuite la qualité de la solution obtenue en résolvent un modèle PLNE restreint qui tire parti des informations recueillies lors de la résolution du dual lagrangien. Les résultats des calculs montrent que les heuristiques donnent rapidement des solutions de bonne qualité, même pour les instances où les solveurs génériques ne trouvent pas de solutions réalisables. Finalement, nous adaptons les heuristiques précédentes pour résoudre le problème industriel. Deux relaxations différentes sont proposées et comparées. Des extensions des concepts précédents sont présentées afin d'assurer une résolution fiable en un temps raisonnable.

Induction of modular classification rules: using Jmax-pruning

The Prism family of algorithms induces modular classification rules which, in contrast to decision tree induction algorithms, do not necessarily fit together into a decision tree structure. Classifiers induced by Prism algorithms achieve a comparable accuracy compared with decision trees and in some cases even outperform decision trees. Both kinds of algorithms tend to overfit on large and noisy datasets and this has led to the development of pruning methods. Pruning methods use various metrics to truncate decision trees or to eliminate whole rules or single rule terms from a Prism rule set. For decision trees many pre-pruning and postpruning methods exist, however for Prism algorithms only one pre-pruning method has been developed, J-pruning. Recent work with Prism algorithms examined J-pruning in the context of very large datasets and found that the current method does not use its full potential. This paper revisits the J-pruning method for the Prism family of algorithms and develops a new pruning method Jmax-pruning, discusses it in theoretical terms and evaluates it empirically.

Jmax-pruning: a facility for the information theoretic pruning of modular classification rules

The Prism family of algorithms induces modular classification rules in contrast to the Top Down Induction of Decision Trees (TDIDT) approach which induces classification rules in the intermediate form of a tree structure. Both approaches achieve a comparable classification accuracy. However in some cases Prism outperforms TDIDT. For both approaches pre-pruning facilities have been developed in order to prevent the induced classifiers from overfitting on noisy datasets, by cutting rule terms or whole rules or by truncating decision trees according to certain metrics. There have been many pre-pruning mechanisms developed for the TDIDT approach, but for the Prism family the only existing pre-pruning facility is J-pruning. J-pruning not only works on Prism algorithms but also on TDIDT. Although it has been shown that J-pruning produces good results, this work points out that J-pruning does not use its full potential. The original J-pruning facility is examined and the use of a new pre-pruning facility, called Jmax-pruning, is proposed and evaluated empirically. A possible pre-pruning facility for TDIDT based on Jmax-pruning is also discussed.

The Environmental Data Abstraction Library (EDAL): a modular approach to processing and visualising large environmental data

The Environmental Data Abstraction Library provides a modular data management library for bringing new and diverse datatypes together for visualisation within numerous software packages, including the ncWMS viewing service, which already has very wide international uptake. The structure of EDAL is presented along with examples of its use to compare satellite, model and in situ data types within the same visualisation framework. We emphasize the value of this capability for cross calibration of datasets and evaluation of model products against observations, including preparation for data assimilation.