High strain rate constitutive modeling forhistorical structures subjected to blast loading

Doctoral Thesis Civil Engineering

Design and Construction Procedures for Concrete Overlay and Widening of Existing Pavements, September 2005

State Highway Departments and local street and road agencies are currently faced with aging highway systems and a need to extend the life of some of the pavements. The agency engineer should have the opportunity to explore the use of multiple surface types in the selection of a preferred rehabilitation strategy. This study was designed to look at the portland cement concrete overlay alternative and especially the design of overlays for existing composite (portland cement and asphaltic cement concrete) pavements. Existing design procedures for portland cement concrete overlays deal primarily with an existing asphaltic concrete pavement with an underlying granular base or stabilized base. This study reviewed those design methods and moved to the development of a design for overlays of composite pavements. It deals directly with existing portland cement concrete pavements that have been overlaid with successive asphaltic concrete overlays and are in need of another overlay due to poor performance of the existing surface. The results of this study provide the engineer with a way to use existing deflection technology coupled with materials testing and a combination of existing overlay design methods to determine the design thickness of the portland cement concrete overlay. The design methodology provides guidance for the engineer, from the evaluation of the existing pavement condition through the construction of the overlay. It also provides a structural analysis of various joint and widening patterns on the performance of such designs. This work provides the engineer with a portland cement concrete overlay solution to composite pavements or conventional asphaltic concrete pavements that are in need of surface rehabilitation.

Relay card for capacitance measurements

In this bachelor's thesis a relay card for capacitance measurements was designed, built and tested. The study was made for the research and development laboratory of VTI Technologies, which manufactures capacitive silicon micro electro mechanical accelerometers and pressure sensors. As the size of the sensors is decreasing the capacitance value of the sensors also decreases. The decreased capacitance causes a need for new and more accurate measurement systems. The technology used in the instrument measuring the capacitance dictates a framework how the relay card should be designed, thus the operating principle of the instrument must be known. To achieve accurate results the measurement instrument and its functions needed to be used correctly. The relay card was designed using printed circuit board design methods that minimize interference coupling to the measurement. The relay card that was designed in this study is modular. It consists of a separate CPU card, which was used to control the add-on cards connected to it. The CPU card was controlled from a computer through a serial bus. Two add-on cards for the CPU card were designed in this study. The first one was the measurement card, which could be used to measure 32 capacitive sensors. The second add-on card was the MUX card, which could be used to switch between two measurement cards. The capacitance measurements carried out through the MUX card and the measurement cards were characterized with a series of test measurements. The test measurement data was then analysed. The relay card design was confirmed to work and offer accurate measurement results up to a measurement frequency of 10 MHz. The length of the measurement cables limited the measurement frequency.

Automatic selection of tidal volume, respiratory frequency and minute ventilation in intubated ICU patients as start up procedure for closed-loop controlled ventilation.

OBJECTIVE: Before a patient can be connected to a mechanical ventilator, the controls of the apparatus need to be set up appropriately. Today, this is done by the intensive care professional. With the advent of closed loop controlled mechanical ventilation, methods will be needed to select appropriate start up settings automatically. The objective of our study was to test such a computerized method which could eventually be used as a start-up procedure (first 5-10 minutes of ventilation) for closed-loop controlled ventilation. DESIGN: Prospective Study. SETTINGS: ICU's in two adult and one children's hospital. PATIENTS: 25 critically ill adult patients (age > or = 15 y) and 17 critically ill children selected at random were studied. INTERVENTIONS: To stimulate 'initial connection', the patients were disconnected from their ventilator and transiently connected to a modified Hamilton AMADEUS ventilator for maximally one minute. During that time they were ventilated with a fixed and standardized breath pattern (Test Breaths) based on pressure controlled synchronized intermittent mandatory ventilation (PCSIMV). MEASUREMENTS AND MAIN RESULTS: Measurements of airway flow, airway pressure and instantaneous CO2 concentration using a mainstream CO2 analyzer were made at the mouth during application of the Test-Breaths. Test-Breaths were analyzed in terms of tidal volume, expiratory time constant and series dead space. Using this data an initial ventilation pattern consisting of respiratory frequency and tidal volume was calculated. This ventilation pattern was compared to the one measured prior to the onset of the study using a two-tailed paired t-test. Additionally, it was compared to a conventional method for setting up ventilators. The computer-proposed ventilation pattern did not differ significantly from the actual pattern (p > 0.05), while the conventional method did. However the scatter was large and in 6 cases deviations in the minute ventilation of more than 50% were observed. CONCLUSIONS: The analysis of standardized Test Breaths allows automatic determination of an initial ventilation pattern for intubated ICU patients. While this pattern does not seem to be superior to the one chosen by the conventional method, it is derived fully automatically and without need for manual patient data entry such as weight or height. This makes the method potentially useful as a start up procedure for closed-loop controlled ventilation.

Pile Design and Tests for Integral Abutment Bridges, HR-273, 1987

Expansion joints increase both the initial cost and the maintenance cost of bridges. Integral abutment bridges provide an attractive design alternative because expansion joints are eliminated from the bridge itself. However, the piles in these bridges are subjected to horizontal movement as the bridge expands and contracts during temperature changes. The objective of this research was to develop a method of designing piles for these conditions. Separate field tests simulating a pile and a bridge girder were conducted for three loading cases: (1) vertical load only, (2) horizontal displacement of pile head only, and (3) combined horizontal displacement of pile head with subsequent vertical load. Both tests (1) and (3) reached the same ultimate vertical load, that is, the horizontal displacement had no effect on the vertical load capacity. Several model tests were conducted in sand with a scale factor of about 1:10. Experimental results from both the field and model tests were used to develop the vertical and horizontal load-displacement properties of the soil. These properties were input into the finite element computer program Integral Abutment Bridge Two-Dimensional (IAB2D), which was developed under a previous research contract. Experimental and analytical results compared well for the test cases. Two alternative design methods, both based upon the American Association of State Highway and Transportation Officials (AASHTO) Specification, were developed. Alternative One is quite conservative relative to IAB2D results and does not permit plastic redistribution of forces. Alternative Two is also conservative when compared to IAB2D, but plastic redistribution is permitted. To use Alternative Two, the pile cross section must have sufficient inelastic rotation capacity before local buckling occurs. A design example for a friction pile and an end-bearing pile illustrates both alternatives.

Design and Operation of the Traffic Simulator, HR-100, 1967

Heavy traffic volumes frequently cause distress in asphalt pavements which were designed under accepted design methods and criteria. The distress appears in the form of rutting in the wheel tracks and rippling or shoving in areas where traffic accelerates or decelerates. Apparently accepted stability test methods alone do not always assure the desired service performance of asphaltic pavements under heavy traffic. The Bituminous Research Laboratory, Engineering Research Institute of Iowa State University undertook the development of a laboratory device by which the resistance of an asphalt paving mix to displacement under traffic might be evaluated, and also be used as a supplemental test to determine adequacy of design of the mix by stability procedures.

Esituotannon aikainen konseptien verifiointi muovituotteen valmistusessa

 Diplomityön tavoitteena on tutkia ja kehittää muovituotteen valmistuskonseptien verifiointimenetelmiä ja luoda malli, jolla saadaan esituotantovaiheestalähtien parannettu tuotantoprosessi massatuotannon aloittamiseen (ramp up). Työn tavoitteena on myös toimia viestintäkeinona lisäämässä organisaation tietoisuutta esituotantovaiheen tärkeydestä. Työ pohjautuu tekijän aikaisempaan tutkimukseen "esituotantoprosessista oppimisen vaikutukset massatuotannon aloitukseen", joka on tehty erikoistyönä v.2006. Tutkimus menetelminä on käytetty pääasiassa prosessien kuvaamista, benchmarkingia, asiantuntijoiden haastatteluja sekä analysoitu toteutuneita projekteja. Lopputuloksena on saatu toimintamalli, joka vastaa hyvin pitkälle prosessien kuvausten aikana syntynyttä mallia. Keskeisenä ajatuksena on valmistuskonseptin verifioinnin kytkeminen tuotteen mekaniikkasuunnittelun kypsyyteen. Koko projektia koskevien tavoitteiden määrittäminen johdetaan ramp up tavoitteista. Verifioitavaksi valitaan kriittisin tuote ja prosessi. Tähän on teoreettisena viitekehyksenä käytetty Quality Function Deployment (QFD) menetelmää. Jatkotoimenpiteiksi esitetään ramp up tavoitteiden ja mittareiden kehittämistä, joilla pystytään seuraamaan ja ohjaamaan projektia jo heti alusta alkaen. Lisätutkimusta tarvitaan myös esituotannon aikaisten prosessiparametrien suunnitteluun ja optimointiin.

Tuotteen suunnitteluketjun tehostaminen 3D-ympäristössä

Tämä diplomityö on tehty Andritz Oy:lle Washers & Filters tuoteryhmään. Työ on osa 3D-suunnittelujärjestelmän käyttöönottoprojektia. Tavoitteena on arvioida uuden laitesuunnittelujärjestelmän vaikutuksia yrityksen tietojärjestelmiin ja toimintatapoihin sekä etsiä potentiaalisia tulevaisuuden kehityskohteita. Suunnittelutietoa hyödyntäviä sidosryhmien edustajia haastattelemalla selvitettiin järjestelmille ja ohjelmistoille asetettavia vaatimuksia. Ohjelmistoihin tutustumalla saatiin käsitys niiden nykytilasta ja kehityssuunnista. 3D-geometrian hyödyntämiseen perustuvilla järjestelmillä voidaan poistaa päällekäistä työtä sekä lyhentää läpimenoaikoja suunnittelussa ja valmistuksessa sijoittamalla työvaiheita rinnakkain. Suurimmat 3D-suunnittelun edut saavutetaan tuotekehitysvaiheessa, tuotemuutoksia tehtäessä sekä valmistusprosesseja suunniteltaessa. Ongelmallisimmat osa-alueet tietojärjestelmien kehittämisessä ovat ensi-sijaisesti tiedonsiirto ohjelmistojen välillä, työntekijöiden muutosvastarinta sekä laadukkaiden järjestelmien korkea hinta. Laajojen tietojärjestelmä-projektien läpivienti on hyvin haastavaa ja onnistuminen vaatii kaikkien sidosryhmien mukana olemista ja tarkkaa projektin koordinointia.

Titaanisen valkaisutornin korjaussuunnitelma

Tämän työn tarkoituksena on poistaa toistuvasti esiintyneet vauriot titaanisessa valkaisutornissa Kuusankosken paperitehtailla. Vauriot esiintyivät melko pian käyttöönoton jälkeen ja niitä esiintyi toistuvasti jokaisen korjauksen jälkeen. Jatkuvatoimisen prosessin vuoksi käyttökatkokset eivät olleet suotavia. Aikataulu suunnittelulle ja korjaukselle oli erittäin tiukka, jolloin kenttämittauksia ei ollut mahdollista tehdä laskelmien tueksi. Tämän vuoksi tähän työtön parhaiten soveltuvaksi menetelmäksi valittiin FEA. Alkuperäisessä rakenteessa pääsäiliöön oli hitsattu pintatasku, jota käytettiin välisäiliönä varastoimaan suuri määrä vaarallista nestettä. Tämä aiheutti valkaisutornin vaipalle murtumia ja vuotoja sekä suuronnettomuuden riskin koko valkaisutornille. Kuormitustietojen puutteesta johtuen kuormitukset mallinnettiin virtuaalisesti FE-menetelmällä ja analyyttisin keinoin. Kuormitusten suuruudet arvioitiin konservatiivisesti. Tämän työn tärkein oivallus oli määritellä uudelleen pintataskun toiminto siten, että sitä ei enää käytetty nesteen välivarastona, vaan ohjaimena nesteelle. Tämä innovatiivinen ongelmankorjauskonsepti on havaittu onnistuneeksi, koska vaurioita ei ole enää esiintynyt viimeisimmän korjauksen jälkeen.

User-Centered Design Gymkhana

The User-centered design (UCD) Gymkhana is a tool for human-computer interaction practitioners to demonstrate through a game the key user-centered design methods and how they interrelate in the design process.The target audiences are other organizational departments unfamiliar with UCD but whose work is related to the definition, cretaion, and update of a product service.

On Fault Tolerance Methods for Networks-on-Chip

Technology scaling has proceeded into dimensions in which the reliability of manufactured devices is becoming endangered. The reliability decrease is a consequence of physical limitations, relative increase of variations, and decreasing noise margins, among others. A promising solution for bringing the reliability of circuits back to a desired level is the use of design methods which introduce tolerance against possible faults in an integrated circuit. This thesis studies and presents fault tolerance methods for network-onchip (NoC) which is a design paradigm targeted for very large systems-onchip. In a NoC resources, such as processors and memories, are connected to a communication network; comparable to the Internet. Fault tolerance in such a system can be achieved at many abstraction levels. The thesis studies the origin of faults in modern technologies and explains the classification to transient, intermittent and permanent faults. A survey of fault tolerance methods is presented to demonstrate the diversity of available methods. Networks-on-chip are approached by exploring their main design choices: the selection of a topology, routing protocol, and flow control method. Fault tolerance methods for NoCs are studied at different layers of the OSI reference model. The data link layer provides a reliable communication link over a physical channel. Error control coding is an efficient fault tolerance method especially against transient faults at this abstraction level. Error control coding methods suitable for on-chip communication are studied and their implementations presented. Error control coding loses its effectiveness in the presence of intermittent and permanent faults. Therefore, other solutions against them are presented. The introduction of spare wires and split transmissions are shown to provide good tolerance against intermittent and permanent errors and their combination to error control coding is illustrated. At the network layer positioned above the data link layer, fault tolerance can be achieved with the design of fault tolerant network topologies and routing algorithms. Both of these approaches are presented in the thesis together with realizations in the both categories. The thesis concludes that an optimal fault tolerance solution contains carefully co-designed elements from different abstraction levels

Kokeellisen moodianalyysin jälkikäsittely ominaismuotojen visuaaliseksi tarkastelemiseksi

Kokeellinen moodianalyysi on kokeellinen menetelmä, jolla voidaan selvittää rakenteille ominaista värähtelyä. Työssä oli kolme tavoitetta, jotka pyrittiin saavuttamaan. Ensimmäinen tavoite oli ohjeistuksen luominen rakenteiden ominaismuotojen visuaaliseksi tarkastelemiseksi Lappeenrannan teknillisellä yliopistolla käytettävissä olevilla laitteistoilla ja ohjelmilla. Ohjeistuksen perustana on ajatus siitä, että kokeellinen moodianalyysi saataisiin tehokkaampaan käyttöön koneensuunnittelun opetuksessa. Ohjeistus tehtiin pääasiassa kuvien ja kuvia tukevien selitysten avulla. Työn toisena tavoitteena oli verrata rakenteen ominaisvärähtelyä, kun se oli tuettu vapaasti ja kun se oli tuettu kiinteästi sen luonnolliseen ympäristöön. Taajuuksia verrattaessa huomattiin, että eri tavoin tuetut rakenteet käyttäytyvät eri tavalla, mikä on otettava huomioon, kun tutkitaan kriittisiä värähtelyjä. Ominaisvärähtelyjä voidaan selvittää myös matemaattisesti esimerkiksi äärellisten elementtien menetelmällä. Työn kolmantena tavoitteena oli verrata elementtimenetelmällä ja kokeellisesti saatuja ominaisvärähtelyn arvoja. Elementtimallia pyrittiin tarkentamaan eri parametrejä muuttamalla niin, että ominaistaajuuksien arvot vastaavat mahdollisimman hyvin toisiaan. Tavoite saavutettiin.

Design of Pulsed Electroacoustic Measurement System for Space Charge Characterisation

Pulsed electroacoustic (PEA) method is a commonly used non-destructive technique for investigating space charges. It has been developed since early 1980s. These days there is continuing interest for better understanding of the influence of space charge on the reliability of solid electrical insulation under high electric field. The PEA method is widely used for space charge profiling for its robust and relatively inexpensive features. The PEA technique relies on a voltage impulse used to temporarily disturb the space charge equilibrium in a dielectric. The acoustic wave is generated by charge movement in the sample and detected by means of a piezoelectric film. The spatial distribution of the space charge is contained within the detected signal. The principle of such a system is already well established, and several kinds of setups have been constructed for different measurement needs. This thesis presents the design of a PEA measurement system as a systems engineering project. The operating principle and some recent developments are summarised. The steps of electrical and mechanical design of the instrument are discussed. A common procedure for measuring space charges is explained and applied to verify the functionality of the system. The measurement system is provided as an additional basic research tool for the Corporate Research Centre of ABB (China) Ltd. It can be used to characterise flat samples with thickness of 0.2–0.5 mm under DC stress. The spatial resolution of the measurement is 20 μm.

Simulation and optimization tools in paper machine concept design

The last decade has shown that the global paper industry needs new processes and products in order to reassert its position in the industry. As the paper markets in Western Europe and North America have stabilized, the competition has tightened. Along with the development of more cost-effective processes and products, new process design methods are also required to break the old molds and create new ideas. This thesis discusses the development of a process design methodology based on simulation and optimization methods. A bi-level optimization problem and a solution procedure for it are formulated and illustrated. Computational models and simulation are used to illustrate the phenomena inside a real process and mathematical optimization is exploited to find out the best process structures and control principles for the process. Dynamic process models are used inside the bi-level optimization problem, which is assumed to be dynamic and multiobjective due to the nature of papermaking processes. The numerical experiments show that the bi-level optimization approach is useful for different kinds of problems related to process design and optimization. Here, the design methodology is applied to a constrained process area of a papermaking line. However, the same methodology is applicable to all types of industrial processes, e.g., the design of biorefiners, because the methodology is totally generalized and can be easily modified.

Design of salient pole PM synchronous machines for a vehicle traction application – Analysis and

This doctoral thesis presents a study on the development of a liquid-cooled frame salient pole permanent-magnet-exited traction machine for a four-wheel-driven electric car. The emphasis of the thesis is put on a radial flux machine design in order to achieve a light-weight machine structure for traction applications. The design features combine electromagnetic and thermal design methods, because traction machine operation does not have a strict operating point. Arbitrary load cycles and the flexible supply require special attention in the design process. It is shown that accurate modelling of the machine magnetic state is essential for high-performance operation. The saturation effect related to the cross-saturation has to be taken carefully into account in order to achieve the desired operation. Two prototype machines have been designed and built for testing: one totally enclosed machine with a special magnet module pole arrangement and another through-ventilated machine with a more traditional embedded magnet structure. Both structures are built with magnetically salient structures in order to increase the torque production capability with the reluctance torque component. Both machine structures show potential for traction usage. However, the traditional embedded magnet design turns out to be mechanically the more secure one of these two machine options.