Evaluation of Preservative Effectiveness of Liquid Crystalline Systems with Retynil Palmitate by the Challenge Test and D-value

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Phase transition in dioctadecyldimethylammonium bromide and chloride vesicles prepared by different methods

The gel to liquid crystalline phase transition of the double-chained cationic dioctadecyldimethylammonium chloride and bromide (DODAX, X = Cl- or Br-) in aqueous vesicle dispersions prepared by non-sonication, sonication and extrusion has been investigated using high-sensitivity differential scanning calorimetry (DSC). The transition temperature (T-m) is a function of the preparation method, amphiphile concentration, vesicle curvature and nature of the counterion. DSC thermograms for DODAB and DODAC non-sonicated vesicle dispersions exhibit a single endothermic peak at T-m roughly independent of concentration up to 10 mM. Extrusion broadens the transition peak and shifts T-m downwards. Sonication, however, broadens slightly the transition peak and tends to shift T-m upwards suggesting that extrusion and sonication form vesicles with different characteristics. DODAC always exhibits higher T-m than DODAB irrespective of the preparation method. T-m changes as follows: T-m (sonicated) greater than or equal to T-m (non-sonicated) > T-m (extruded). Hysteresis of about 7 degrees C was observed for DODAB vesicle dispersions. (C) 2000 Elsevier B.V. Ireland Ltd. All rights reserved.

Kinetic asymmetry in the gel-liquid crystalline state transitions of DDAB vesicles studied by differential scanning calorimetry

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Liquid-gas phase transition in Bose-Einstein condensates with time evolution

We study the effects of a repulsive three-body interaction on a system of trapped ultracold atoms in a Bose-Einstein condensed state. The stationary solutions of the corresponding s-wave nonlinear Schrödinger equation suggest a scenario of first-order liquid-gas phase transition in the condensed state up to a critical strength of the effective three-body force. The time evolution of the condensate with feeding process and three-body recombination losses has a different characteristic pattern. Also, the decay time of the dense (liquid) phase is longer than expected due to strong oscillations of the mean-squared radius.

Microstructure, crystalline phase, and dielectric property analyses of TiO2 composition with ZrO2 addition

For microwave applications, including mobile and satellite communications, ceramic resonators should have a high dielectric constant, low dielectric losses, and high frequency stability. In this sense, TiO2-ZrO 2 ceramics have been investigated as a function of sintering behavior, phase composition, and microstructure. The ceramics were densified reaching a value of about 86% of theoretical density at 1400°C sintering temperature. The ceramics are prepared by mixing raw materials with the following TiO2-ZrO2 weight % ratio: 100 to 0, 90 to 10, and 80 to 20, respectively. The measured dielectric constants are between 79 and 88 values, while the quality factor due to dielectric losses are between 2820 and 5170. These results point out the influence of Ti/Zr ratio on controlling the dielectric properties. © (2010) Trans Tech Publications.

Evaluation of preservative effectiveness of liquid crystalline systems with retinyl palmitate by the challenge test and D-value

The objective of this work was to evaluate the preservative effectiveness of liquid crystalline systems containing retynil palmitate (RP) by the challenge test (CT) and D-value. A system was developed containing water, silicon glycol copolymer, and polyether functional siloxane with 1% RP added. The analyses were carried out by methods in the U.S. Pharmacopeia (USP 31, 2008) using the microorganisms Escherichia coli, Staphylococcus aureus,Pseudomonas aeruginosa, Candida albicans, and Aspergillus niger. The CT showed that after 7 days, all microorganisms were eliminated except A. niger, which maintained viability for at least 28 days after inoculation. Moreover, the microorganisms E. coli, P. aeruginosa, S. aureus, C. albicans and A. niger presented different growth behaviors, evidenced by differences among the D-values calculated. It was concluded that the CT and D-value were efficient methods for evaluation of the preservative property of these formulations.

Liquid crystalline hexabenzocoronenes as organic molecular materials - synthesis, characterization and application

Die vorliegende Arbeit 'Liquid Crystalline Hexabenzocoronenes as Organic Molecular Materials - Synthesis, Characterization and Application' war durch drei Schwerpunkte definiert:1. Verbesserung der Synthese von Hexabenzocoronen Derivaten mit sechsfacher Alkyl-Substitution,2. Entwicklung von molekularen Materialien mit verbesserten Eigenschaften wie zum Beispiel Löslichkeit und Verarbeitbarkeit,3. Einsatz der entwickelten Moleküle in optoelektronischen Bauteilen wie zum Beispiel organischen Solarzellen und Feld-Effekt-Transistoren.Mit Hilfe einer neuen Syntheseroute ist es gelungen Aryl-Aryl und Aryl-Alkyl Kupplungen sehr spät in der Reaktionssequenz von Hexabenzocoronenen einzusetzen. Dies führte zu einer Vielzahl substituierter HBC Derivate. Die Einführung eines Phenyl Spacers zwischen den HBC Kern und die äußeren Alkylketten, wie zum Beispiel in HBC-PhC12, hatte eine Vielzahl positiver Effekte wie dramatisch verbesserte Löslichkeit und Flüssigkristallinität bei Raumtemperatur zur Folge. Die Kombination dieser Phänomene ermöglichte die Bildung hochgeordneter Filme, welche sehr wichtig für den Einsatz in organischen Bauelementen sind. Mit Hilfe von STM Techniken an der Fest-Flüssig Phasengrenze wurden hochgeordnete 2-D Strukturen der HBC Moleküle gefunden. Die Kombination von extrem hoher kolumnarer Ordnung, bestimmt mit Hilfe der Festkörper NMR Spektroskopie, mit einer konstant hohen Ladungsträgerbeweglichkeit, führte zu dem sehr erfolgreichen Einsatz von HBC-PhC12 in organischen Solarzellen.

C 3-symmetric discotic liquid crystalline materials for molecular electronics: versatile synthesis and self-organization

This thesis presents the versatile synthesis and self-organization of C3-symmetric discotic nanographene molecules as well as their potential applications as materials in molecular electronics. The details can be described as follows: 1) A novel synthetic strategy towards properly designed C3 symmetric 1,3,5-tris-2’arylbenzene precursors has been developed. After the final planarization by treatment with FeCl3 under mild conditions, for the first time, it became possible to access a variety of new C3-symmetric hexa-peri-hexabenzocoronenes (HBCs) and a series of triangle-shaped nanographenes. D3 symmetric HBC with three alkyl substituents and C2 symmetric HBC with two alkyl substituents were synthesized and found to show the surprising decrease of isotropic points., the self-assembly at the liquid-solid interface displayed a unique zigzag and flower patterns. 2) Triangle-shaped discotics revealed a unique self-assembly behavior in solution, solid state as well as at the solution-substrate interface. A mesophase stability over the broad temperature range with helical supramoelcular arrangement were observed in the bulk state. The honeycomb pattern as the result of novel self-assembly was presented. Triangle-shaped discotics with swallow alkyl tails were fabricated into photovoltaic devices, the supramolecular arrangement upon thermal treatment was found to play a key role in the improvement of solar efficiency. 3) A novel class of C3 symmetric HBCs with alternating polar/apolar substituents was synthesized. Their peculiar self-assembly in solution, in the bulk and on the surface were investigated by NMR techniques, X-ray diffraction as well as different electron microscope techniques. 4) A novel concept for manipulating the intracolumnar stacking of discotics and thus for controlling the helical pitch was presented. A unique staggered stacking in the column was achieved for the first time. Theoretical simulations confirmed this self-organization and predicted that this packing should show the highest charge carrier mobility for all discotics.

Liquid crystalline phases of anisotropic, polymer functionalized nanoparticles

Diese Arbeit beschäftigt sich mit der Polymerfunktionalisierung formanisotroperrnNanopartikel wie TiO2 Nanostäbchen oder Kohlenstoff Nanoröhren. Dies dient derrnSolubilisierung und sterischen Stabilisierung in organischen Medien, da diesernionenfrei hergestellt werden können, was eine Nutzung für nanoskopische,rnelektrische Schaltkreise ermöglicht. Die Polymere wurden mittels der RAFTrn(reversible addition-fragmentation chain transfer) Polymerisation mit engenrnMolekulargewichtsverteilungen hergestellt. Im Detail wurden Ankergruppen inrnBlockcopolymere und an der Alphaposition eingeführt, welche eine Anbindung an diernNanopartikeloberfläche ermöglichen. Die Polymere wurden durch Variation derrnverschiedenen Blocklängen für eine bestmögliche Adsorption optimiert. Die sorngewonnenen Polymer funktionalisierten Nanopartikel zeigten eine gute Löslichkeit inrnorganischen Medien und zeigten zudem eine lyotropes, flüssigkristallinesrnPhasenverhalten. Dies war aufgrund der Formanisotropie zu erwarten, zeigte jedochrnebenfalls ein unerwartetes thermotropes Verhalten, welches durch die Polymerhüllernerzeugt wurde. Die Flüssigkristalle wurden eingehend mittels polarisierterrnMikroskopie und Differential Scanning Calorimetry (DSC) untersucht. Diernflüssigkristallinen Phasen aus Nanostäbchen und –röhren wurde dann zurrnOrientierung der anisotropen Nanopartikel benutzt und es konnten makroskopischrngeordnete Proben hergestellt werden. Die Polymerhülle um die Nanopartikelrnermöglichte es ebenfalls diese in Polymerfilme einzuarbeiten und sornNanopartikelverstärkte Kunststoffe herzustellen.

DEVELOPMENT OF CONFOCAL IMAGING TECHNIQUES FOR PROBING INTERFACIAL DYNAMICS IN MICROSCALE, GAS-LIQUID, TWO-PHASE FLOW

Micro-scale, two-phase flow is found in a variety of devices such as Lab-on-a-chip, bio-chips, micro-heat exchangers, and fuel cells. Knowledge of the fluid behavior near the dynamic gas-liquid interface is required for developing accurate predictive models. Light is distorted near a curved gas-liquid interface preventing accurate measurement of interfacial shape and internal liquid velocities. This research focused on the development of experimental methods designed to isolate and probe dynamic liquid films and measure velocity fields near a moving gas-liquid interface. A high-speed, reflectance, swept-field confocal (RSFC) imaging system was developed for imaging near curved surfaces. Experimental studies of dynamic gas-liquid interface of micro-scale, two-phase flow were conducted in three phases. Dynamic liquid film thicknesses of segmented, two-phase flow were measured using the RSFC and compared to a classic film thickness deposition model. Flow fields near a steadily moving meniscus were measured using RSFC and particle tracking velocimetry. The RSFC provided high speed imaging near the menisci without distortion caused the gas-liquid interface. Finally, interfacial morphology for internal two-phase flow and droplet evaporation were measured using interferograms produced by the RSFC imaging technique. Each technique can be used independently or simultaneously when.

Liquid-Crystalline Dendrimers Designed by Click Chemistry

Liquid-crystalline dendrimers have been prepared from second-generation Percec-type poly(benzyl ether) dendrons or second-generation poly(aryl ester) dendrons carrying cyanobiphenyl mesogens. The Janus dendrimer, which combines the two types of dendromesogens, has also been synthesized. Those compounds have been prepared under copper-catalyzed azide–alkyne cycloaddition conditions. The mesomorphic properties have been studied by thermal analysis (POM, DSC) and small-angle X-ray scattering. Smectic A, nematic, and columnar phases have been observed depending on the dendritic building blocks. The click reaction has proven to be a powerful and elegant synthetic tool for the design of complex dendritic liquid-crystalline architectures.

Adaptive liquid-crystal phase-only passive devices

This PhD work is focused on liquid crystal based tunable phase devices with special emphasis on their design and manufacturing. In the course of the work a number of new manufacturing technologies have been implemented in the UPM clean room facilities, leading to an important improvement in the range of devices being manufactured in the laboratory. Furthermore, a number of novel phase devices have been developed, all of them including novel electrodes, and/or alignment layers. The most important manufacturing progress has been the introduction of reactive ion etching as a tool for achieving high resolution photolithography on indium-tin-oxide (ITO) coated glass and quartz substrates. Another important manufacturing result is the successful elaboration of a binding protocol of anisotropic conduction adhesives. These have been employed in high density interconnections between ITO-glass and flexible printed circuits. Regarding material characterization, the comparative study of nonstoichiometric silicon oxide (SiOx) and silica (SiO2) inorganic alignment layers, as well as the relationship between surface layer deposition, layer morphology and liquid crystal electrooptical response must be highlighted, together with the characterization of the degradation of liquid crystal devices in simulated space mission environment. A wide variety of phase devices have been developed, with special emphasis on beam steerers. One of these was developed within the framework of an ESA project, and consisted of a high density reconfigurable 1D blaze grating, with a spatial separation of the controlling microelectronics and the active, radiation exposed, area. The developed devices confirmed the assumption that liquid crystal devices with such a separation of components, are radiation hard, and can be designed to be both vibration and temperature sturdy. In parallel to the above, an evenly variable analog beam steering device was designed, manufactured and characterized, providing a narrow cone diffraction free beam steering. This steering device is characterized by a very limited number of electrodes necessary for the redirection of a light beam. As few as 4 different voltage levels were needed in order to redirect a light beam. Finally at the Wojskowa Akademia Techniczna (Military University of Technology) in Warsaw, Poland, a wedged analog tunable beam steering device was designed, manufactured and characterized. This beam steerer, like the former one, was designed to resist the harsh conditions both in space and in the context of the shuttle launch. Apart from the beam steering devices, reconfigurable vortices and modal lens devices have been manufactured and characterized. In summary, during this work a large number of liquid crystal devices and liquid crystal device manufacturing technologies have been developed. Besides their relevance in scientific publications and technical achievements, most of these new devices have demonstrated their usefulness in the actual work of the research group where this PhD has been completed. El presente trabajo de Tesis se ha centrado en el diseño, fabricación y caracterización de nuevos dispositivos de fase basados en cristal líquido. Actualmente se están desarrollando dispositivos basados en cristal líquido para aplicaciones diferentes a su uso habitual como displays. Poseen la ventaja de que los dispositivos pueden ser controlados por bajas tensiones y no necesitan elementos mecánicos para su funcionamiento. La fabricación de todos los dispositivos del presente trabajo se ha realizado en la cámara limpia del grupo. La cámara limpia ha sido diseñada por el grupo de investigación, es de dimensiones reducidas pero muy versátil. Está dividida en distintas áreas de trabajo dependiendo del tipo de proceso que se lleva a cabo. La cámara limpia está completamente cubierta de un material libre de polvo. Todas las entradas de suministro de gas y agua están selladas. El aire filtrado es constantemente bombeado dentro de la zona limpia, a fin de crear una sobrepresión evitando así la entrada de aire sin filtrar. Las personas que trabajan en esta zona siempre deben de estar protegidas con un traje especial. Se utilizan trajes especiales que constan de: mono, máscara, guantes de látex, gorro, patucos y gafas de protección UV, cuando sea necesario. Para introducir material dentro de la cámara limpia se debe limpiar con alcohol y paños especiales y posteriormente secarlos con nitrógeno a presión. La fabricación debe seguir estrictamente unos pasos determinados, que pueden cambiar dependiendo de los requerimientos de cada dispositivo. Por ello, la fabricación de dispositivos requiere la formulación de varios protocolos de fabricación. Estos protocolos deben ser estrictamente respetados a fin de obtener repetitividad en los experimentos, lo que lleva siempre asociado un proceso de fabricación fiable. Una célula de cristal líquido está compuesta (de forma general) por dos vidrios ensamblados (sándwich) y colocados a una distancia determinada. Los vidrios se han sometido a una serie de procesos para acondicionar las superficies internas. La célula se llena con cristal líquido. De forma resumida, el proceso de fabricación general es el siguiente: inicialmente, se cortan los vidrios (cuya cara interna es conductora) y se limpian. Después se imprimen las pistas sobre el vidrio formando los píxeles. Estas pistas conductoras provienen del vidrio con la capa conductora de ITO (óxido de indio y estaño). Esto se hace a través de un proceso de fotolitografía con una resina fotosensible, y un desarrollo y ataque posterior del ITO sin protección. Más tarde, las caras internas de los vidrios se acondicionan depositando una capa, que puede ser orgánica o inorgánica (un polímero o un óxido). Esta etapa es crucial para el funcionamiento del dispositivo: induce la orientación de las moléculas de cristal líquido. Una vez que las superficies están acondicionadas, se depositan espaciadores en las mismas: son pequeñas esferas o cilindros de tamaño calibrado (pocos micrómetros) para garantizar un espesor homogéneo del dispositivo. Después en uno de los sustratos se deposita un adhesivo (gasket). A continuación, los sustratos se ensamblan teniendo en cuenta que el gasket debe dejar una boca libre para que el cristal líquido se introduzca posteriormente dentro de la célula. El llenado de la célula se realiza en una cámara de vacío y después la boca se sella. Por último, la conexión de los cables a la célula y el montaje de los polarizadores se realizan fuera de la sala limpia (Figura 1). Dependiendo de la aplicación, el cristal líquido empleado y los demás componentes de la célula tendrán unas características particulares. Para el diseño de los dispositivos de este trabajo se ha realizado un estudio de superficies inorgánicas de alineamiento del cristal líquido, que será de gran importancia para la preparación de los dispositivos de fase, dependiendo de las condiciones ambientales en las que vayan a trabajar. Los materiales inorgánicos que se han estudiado han sido en este caso SiOx y SiO2. El estudio ha comprendido tanto los factores de preparación influyentes en el alineamiento, el comportamiento del cristal líquido al variar estos factores y un estudio de la morfología de las superficies obtenidas.

Comb-like acrylic-based polymer latexes containing nano-sized crystalline or liquid crystalline domains

306 p.