An experimental analysis of operating conditions in cold roll-forming

A detailed literature survey confirmed cold roll-forming to be a complex and little understood process. In spite of its growing value, the process remains largely un-automated with few principles used in set-up of the rolling mill. This work concentrates on experimental investigations of operating conditions in order to gain a scientific understanding of the process. The operating conditions are; inter-pass distance, roll load, roll speed, horizontal roll alignment. Fifty tests have been carried out under varied operating conditions, measuring section quality and longitudinal straining to give a picture of bending. A channel section was chosen for its simplicity and compatibility with previous work. Quality measurements were measured in terms of vertical bow, twist and cross-sectional geometric accuracy, and a complete method of classifying quality has been devised. The longitudinal strain profile was recorded, by the use of strain gauges attached to the strip surface at five locations. Parameter control is shown to be important in allowing consistency in section quality. At present rolling mills are constructed with large tolerances on operating conditions. By reduction of the variability in parameters, section consistency is maintained and mill down-time is reduced. Roll load, alignment and differential roll speed are all shown to affect quality, and can be used to control quality. Set-up time is reduced by improving the design of the mill so that parameter values can be measured and set, without the need for judgment by eye. Values of parameters can be guided by models of the process, although elements of experience are still unavoidable. Despite increased parameter control, section quality is variable, if only due to variability in strip material properties. Parameters must therefore be changed during rolling. Ideally this can take place by closed-loop feedback control. Future work lies in overcoming the problems connected with this control.

The use of lubricants in iron powder metallurgy

This investigation has been concerned with the behaviour of solid internal lubricant during mixing, compaction, ejection, dewaxing and sintering of iron powder compacts. Zinc stearate (0.01%-4.0%) was added to irregular iron powder by admixing or precipitation from solution. Pressure/density relationships, determined by continuous compaction, and loose packed densities were used to show that small additions of zinc stearate reduced interparticle friction during loose packing and at low compaction pressures. Large additions decreased particle/die-wall friction during compaction and ejection but also caused compaction inhibition. Transverse rupture strengths were determined on compacts containing various stearate based lubricants and it was found that green strength was reduced by the interposition of a thin lubricant layer within inter~particle contacts. Only materials much finer than the iron powder respectively) were able to form such layers. Investigations were undertaken to determine the effect of the decomposition of these lubricants on the development of mechanical properties in dewaxed or sintered compacts. Physical and chemical influences on tensile strength were observed. Decomposition of lubricants was associated with reductions of strength caused by the physical effects of pressure increases and removal of lubricant from interparticle contacts. There were also chemical effects associated with the influence of gaseous decomposition products and solid residues on sintering mechanisms. Thermogravimetry was used to study the decomposition behaviour of various lubricants as free compounds and within compacts. The influence of process variables such as atmosphere type, flow-rate and compact density were investigated. In a reducing atmosphere the decomposition of these lubricants was characterised by two stages. The first involved the rapid decomposition of the hydrocarbon radical. The second, higher temperature, reactions depended on lubricant type and involved solid residues. The removal of lubricant could also markedly affect dimensional change.

Towards asphalt mixture morphology evaluation with the virtual specimen approach

The morphology of asphalt mixture can be defined as a set of parameters describing the geometrical characteristics of its constituent materials, their relative proportions as well as spatial arrangement in the mixture. The present study is carried out to investigate the effect of the morphology on its meso- and macro-mechanical response. An analysis approach is used for the meso-structural characterisation based on the X-ray computed tomography (CT) data. Image processing techniques are used to systematically vary the internal structure to obtain different morphology structures. A morphology framework is used to characterise the average mastic coating thickness around the main load carrying structure in the structures. The uniaxial tension simulation shows that the mixtures with the lowest coating thickness exhibit better inter-particle interaction with more continuous load distribution chains between adjacent aggregate particles, less stress concentrations and less strain localisation in the mastic phase.

Preferência e competição alimentar em um grupo de Sapajus flavius em fragmento de Mata Atlântica em Caaporã – Paraíba – Brasil

Feeding is the primary selective pressure in all forms of animals. Nutritional ecological models predict consequences of preferred and non-preferred food consumption on behavioural, physiological and morphological adaptations. At same time, socioecological models infer socio-organizarion patterns based on feeding competition faced by animals. A list of preferred foods, and inferences regarding the intensity of feeding competition and its behavioural consequences are information of much importance for management of populations in fragments. In this work we observed the feeding behavior and spatial positioning of a group of more than 100 blond capuchin monkeys (Sapajus flavius) that inhabit a fragment of Atlantic forest, surrounded by sugarcane plantation. We compared the consumption of different food items with their monthly availability in the area to define the preferred and fallback food items. We recorded the vocalizations of aggression and the inter-individual distance (area of Minimum Convex Polygon/n individuals) to infer the type of food competition experienced by animals. In the year studied the fruit feeding time correlated with top consumed fruit productivity, indicating preference for fruits. Our data indicate that the species Elaeis sp., Cecropia palmata, Inga spp. and Simarouba amara are the preferred food items in the diet. Available all year round and uniformly distributed, sugarcane was a regular item in the diet and its was characterized as a staple fallback food for this group. Although fruits are preferential food items, direct competition rate did not correlate to fruit productivity in the area, maintaining the high rates throughout the year (2.45 events/ hour). The inter-individual distance index positively correlated with rain fall indicating scramble food competition. The number of neighbours of females carrying infants was smaller when fruit productivity is low, indicating that females carrying infants are suffering increased indirect competition. Our data indicates that blond capuchins in this fragment make use of sugar cane as a staple fallback food, which evidence the importance of sugar cane landscape for the survival of this critically endangered capuchin species in fragmented habitats in Northeast Brazil. A preliminary list of preferred and important foods is offered, and can assist in the choice of trees for reforestation, better fragments to be preserved and areas of release and translocation of animals. We did not observe an increase of contest competition while using preferred foods, but when using staple FBF. This may be due the altered environment, which results in high competition food throughout the year. Both the food preference as the social and behavioral consequences of high food competition experienced by animals in this fragment must be accompanied over the years to ensure the survival of this population.

Preferência e competição alimentar em um grupo de Sapajus flavius em fragmento de Mata Atlântica em Caaporã – Paraíba – Brasil

Feeding is the primary selective pressure in all forms of animals. Nutritional ecological models predict consequences of preferred and non-preferred food consumption on behavioural, physiological and morphological adaptations. At same time, socioecological models infer socio-organizarion patterns based on feeding competition faced by animals. A list of preferred foods, and inferences regarding the intensity of feeding competition and its behavioural consequences are information of much importance for management of populations in fragments. In this work we observed the feeding behavior and spatial positioning of a group of more than 100 blond capuchin monkeys (Sapajus flavius) that inhabit a fragment of Atlantic forest, surrounded by sugarcane plantation. We compared the consumption of different food items with their monthly availability in the area to define the preferred and fallback food items. We recorded the vocalizations of aggression and the inter-individual distance (area of Minimum Convex Polygon/n individuals) to infer the type of food competition experienced by animals. In the year studied the fruit feeding time correlated with top consumed fruit productivity, indicating preference for fruits. Our data indicate that the species Elaeis sp., Cecropia palmata, Inga spp. and Simarouba amara are the preferred food items in the diet. Available all year round and uniformly distributed, sugarcane was a regular item in the diet and its was characterized as a staple fallback food for this group. Although fruits are preferential food items, direct competition rate did not correlate to fruit productivity in the area, maintaining the high rates throughout the year (2.45 events/ hour). The inter-individual distance index positively correlated with rain fall indicating scramble food competition. The number of neighbours of females carrying infants was smaller when fruit productivity is low, indicating that females carrying infants are suffering increased indirect competition. Our data indicates that blond capuchins in this fragment make use of sugar cane as a staple fallback food, which evidence the importance of sugar cane landscape for the survival of this critically endangered capuchin species in fragmented habitats in Northeast Brazil. A preliminary list of preferred and important foods is offered, and can assist in the choice of trees for reforestation, better fragments to be preserved and areas of release and translocation of animals. We did not observe an increase of contest competition while using preferred foods, but when using staple FBF. This may be due the altered environment, which results in high competition food throughout the year. Both the food preference as the social and behavioral consequences of high food competition experienced by animals in this fragment must be accompanied over the years to ensure the survival of this population.

Application of Numerical Methods to Study Arrangement and Fracture of Lithium-Ion Microstructure

The focus of this work is to develop and employ numerical methods that provide characterization of granular microstructures, dynamic fragmentation of brittle materials, and dynamic fracture of three-dimensional bodies.

We first propose the fabric tensor formalism to describe the structure and evolution of lithium-ion electrode microstructure during the calendaring process. Fabric tensors are directional measures of particulate assemblies based on inter-particle connectivity, relating to the structural and transport properties of the electrode. Applying this technique to X-ray computed tomography of cathode microstructure, we show that fabric tensors capture the evolution of the inter-particle contact distribution and are therefore good measures for the internal state of and electronic transport within the electrode.

We then shift focus to the development and analysis of fracture models within finite element simulations. A difficult problem to characterize in the realm of fracture modeling is that of fragmentation, wherein brittle materials subjected to a uniform tensile loading break apart into a large number of smaller pieces. We explore the effect of numerical precision in the results of dynamic fragmentation simulations using the cohesive element approach on a one-dimensional domain. By introducing random and non-random field variations, we discern that round-off error plays a significant role in establishing a mesh-convergent solution for uniform fragmentation problems. Further, by using differing magnitudes of randomized material properties and mesh discretizations, we find that employing randomness can improve convergence behavior and provide a computational savings.

The Thick Level-Set model is implemented to describe brittle media undergoing dynamic fragmentation as an alternative to the cohesive element approach. This non-local damage model features a level-set function that defines the extent and severity of degradation and uses a length scale to limit the damage gradient. In terms of energy dissipated by fracture and mean fragment size, we find that the proposed model reproduces the rate-dependent observations of analytical approaches, cohesive element simulations, and experimental studies.

Lastly, the Thick Level-Set model is implemented in three dimensions to describe the dynamic failure of brittle media, such as the active material particles in the battery cathode during manufacturing. The proposed model matches expected behavior from physical experiments, analytical approaches, and numerical models, and mesh convergence is established. We find that the use of an asymmetrical damage model to represent tensile damage is important to producing the expected results for brittle fracture problems.

The impact of this work is that designers of lithium-ion battery components can employ the numerical methods presented herein to analyze the evolving electrode microstructure during manufacturing, operational, and extraordinary loadings. This allows for enhanced designs and manufacturing methods that advance the state of battery technology. Further, these numerical tools have applicability in a broad range of fields, from geotechnical analysis to ice-sheet modeling to armor design to hydraulic fracturing.

The Provenance and Geochemical Alteration of Bermudan Eolianites

Large calcareous eolianites cover the remote island of Bermuda, accounting for more than 90% of the limestone bedrock. This study examines the sedimentology and geochemistry of these eolianites to better understand Pleistocene oceanography and the meteoric alteration of subtropical carbonate sediments. Cluster analyses reveal that the eolian carbonate sediments fall into two natural groups that represent lagoonal and reefal end members of marine sediment production. Coral fragments are uncharacteristically absent, possibly destroyed prior to their incorporation into eolian deposits by endolithic microboring organisms or broken up during transport. Sediment assemblages lead to the following interpretations of the Bermudan offshore environment: (1) the Ledge Flats reef system along the southwestern coast has been active since MIS 11, contributing coralline algal-rich sediment to the northern beaches of Sandy’s Parish and acting as an energy barrier in the south, allowing for low energy sedimentation in the quiet back- reef region; (2) on the northeastern coast, the low energy back-reef region landward of the Ledge Flats has thrived since MIS 11; (3) during MIS 5e, slightly warmer water temperatures led to the hindrance of coralline algal growth along the southern coast and in the North Lagoon. These are the first interpretations of Pleistocene marine assemblages on Bermuda. Meteoric fluids progressively transformed the pristine carbonate sediments into hardened limestones in a predictable solubility-dependent manner. The progressive alteration is coincident with: (1) divergence of δ18O and δ13C values from those similar to unaltered sediment towards those of calcrete, due to interaction with CO2-charged meteoric fluids; (2) depletion of elements with low partitioning coefficients and low meteoric concentrations, such as barium, boron, magnesium, potassium, sodium, strontium, and uranium; (3) enrichment of iron from Terra Rossa-hosted iron oxides; (4) enrichment of aluminum via detrital minerals sourced from protosol horizons; and (5) manganese concentrations that remain uncharacteristically low, owing to the lack of a consistent manganese source. Elemental correlations are useful for characterizing meteoric diagenesis, assuming the primary mineralogy is recognized, all components have been fully altered, and inter-particle cements are ubiquitous.

Non-equilibrium thermodynamics of harmonically trapped bosons

We apply the framework of non-equilibrium quantum thermodynamics to the physics of quenched small-size bosonic quantum gases in a harmonic trap. By studying the temporal behaviour of the Loschmidt echo and of the atomic density profile within the trap, which are informative of the non-equilibrium physics and the correlations among the particles, we establish a link with the statistics of (irreversible) work done on the system. This highlights interesting connections between the degree of inter-particle entanglement and the non-equilibrium thermodynamics of the system.

Spike-timing dependent plasticity and connectivity in primate sensorimotor cortex

Thesis (Ph.D.)--University of Washington, 2016-06

Concussion: Examining the Effect of Neuronal Oxidative Stress on the Pathophysiology of Brain and Blood Brain Barrier Cells

Neuronal stretching during concussion alters glucose transport and reduces neuronal viability, also affecting other cells in the brain and the Blood Brain Barrier (BBB). Our hypothesis is that oxidative stress (OS) generated in neurons during concussions contributes to this outcome. To validate this, we investigated: (1) whether OS independently causes alterations in brain and BBB cells, namely human neuron-like, neuroblastoma cells (NCs), astrocyte cells (ACs) and brain microvascular endothelial cells (ECs), and (2) whether OS originated in NCs (as in concussion) is responsible for causing the subsequent alterations observed in ACs and ECs. We used H2O2 treatment to mimic OS, validated by examining the resulting reactive oxygen species, and evaluated alterations in cell morphology, expression and localization of the glucose transporter GLUT1, and the overall cell viability. Our results showed that OS, either directly affecting each cell type or originally affecting NCs, caused changes in several morphological parameters (surface area, Feret diameter, circularity, inter-cellular distance), slightly varied GLUT1 expression and lowered the overall cell viability of all NCs, ACs, and ECs. Therefore, we can conclude that oxidative stress, which is known to be generated during concussion, caused alterations in NCs, ACs, and ECs whether independently originated in each cell or when originated in the NCs and could further propagate the ACs and ECs.

Specimen generation approaches for DEM simulations.

Discrete Element Method (DEM) simulations ofelement tests cam provide significant insight into the micro-mechanics of soil response. It is well established that soil behaviour is strongly dependant on the initial density. Generation of particulate assemblies for three-dimensional DEM analyses must therefore allow for void ratio control. In this paper, different specimen generation approaches for DEM analyses are discussed. A methodology for the generation of assemblies of spherical particles with a specified initial density and stress state is presented. The effects of the different preparation methods on the specimen fabric are then considered in detail. For isotropic consolidation, it is shown that varying the coefficient of inter-particle friction allows control of the specimen void ratio at a specified confining stress. Simulations of anisotropic consolidation, from an initial isotropic stress state, to a final state where sigma(3) = K(0)sigma(1) indicated that the specimen void ratio and fabric are relatively insensitive to the intermediate stress path, provided an intermediate stress along the K(0) line was attained.

Raman spectroscopy study of the transformation of the carbonaceous skeleton of a polymer-based nanoporous carbon along the thermal annealing pathway

We report a multi-wavelength Raman spectroscopy study of the structural changes along the thermal annealing pathway of a poly(furfuryl alcohol) (PFA) derived nanoporous carbon (NPC). The Raman spectra were deconvoluted utilizing G, D, D′, A and TPA bands. The appropriateness of these deconvolutions was confirmed via recovery of the correct dispersive behaviours of these bands. It is proposed that the ID/IG ratio is composed of two parts: one associated with the extent of graphitic crystallites (the Tuinstra–Koenig relationship), and a second related to the inter-defect distance. This model was used to successfully determine the variation of the in-plane size and intra-plane defect density along the annealing pathway. It is proposed that the NPC skeleton evolves along the annealing pathway in two stages: below 1600 °C it was dominated by a reduction of in-plane defects with a minor crystallite growth, and above this temperature growth of the crystallites accelerates as the in-plane defect density approaches zero. A significant amount of transpolyacetylene (TPA)-like structures was found to be remaining even at 2400 °C. These may be responsible for resistance to further graphitization of the PFA-based carbon at higher temperatures.

Agriculture and forest: A sustainable strategy in the Brazilian Amazon.

Large-scale agriculture is increasing in anthropogenically modified areas in the Amazon Basin. Crops such as soybean, maize, oil palm, and others are being introduced to supply the world demand for food and energy. However, the current challenge is to enhance the sustainability of these areas by increasing efficiency of production chains and to improve environmental services. The Amazon Basin has experienced a paradigm shift away from the traditional slash-and-burn agricultural practices, which offers decision makers the opportunity to make innovative interventions to enhance the productivity in previously degraded areas by using trees to ecological advantage. This study describes a successful experiment integrating the production of soybean and paricá (Glycine max L. and Schizolobium amazonicum) based on previous research that indicated potential topoclimatic zones for planting paricá in the Brazilian state of Pará. This paper shows that a no-tillage system reduces the effects of drought compared to conventional tillage still used by many farmers in the region. The integrated system was implemented during the 2014/2015 season in 234.6 ha in the high-potential zone in the municipality of Ulianópolis, Pará. Both soybean and paricá were planted simultaneously. Paricá was planted in 5 m x 2 m inter-tree spacing totaling 228x103 trees per hectare and soybean, in 4 m x 100 m spacing, distributed in nine rows with a 0.45 m inter-row distance, occupying 80% of the area. The harvested soybean production was 3.4 t ha-1, higher than other soybean monocultures in eastern Pará. Paricá benefited from soybean fertilization in the first year: It exhibited rapid development in height (3.26 m) and average diameter (3.85 cm). Trees and crop rotation over the following years is six years for forest species and one year for each crop. Our results confirm there are alternatives to the current production systems able to diminish negative impacts resulting from monoculture. In addition, the system provided environmental services such as reduced soil erosion and increased carbon stock by soil cover with no-tillage soybean cultivation. The soybean cover contributes to increased paricá thermal regulation and lower forestry costs. We concluded that innovative interventions are important to show local farmers that it is possible to adapt an agroforest system to large-scale production, thus changing the Amazon.

Motion Cueing Algorithm Development in a 2DOF Driving Simulator: a Driving Behaviour-Centered Approach

I simulatori di guida sono strumenti altamente tecnologici che permettono di svolgere attività di ricerca in vari ambiti quali la psicologia, la medicina e l’ingegneria. Tuttavia, affinché i dati ottenuti mediante le simulazioni siano rapportabili alla loro controparte reale, la fedeltà delle componenti del simulatore di guida deve essere elevata. Questo lavoro tratta del miglioramento del sistema di restituzione del movimento nel simulatore a due gradi di libertà (2DOF) SIMU-LACET Driving Simulator, costruito e sviluppato presso il laboratorio LEPSIS dell’IFSTTAR (Istituto Francese delle Scienze e Tecnologie dei Trasporti, dello Sviluppo e delle Reti), in particolare nella sua sede di Parigi – Marne-la-Vallée. Si è deciso di andare a riprogettare la parte software del sistema di restituzione del movimento (motion cueing), operando su due elementi principali: lo scale factor (fattore di scala) applicato agli impulsi dinamici provenienti dal modello veicolare e i Motion Cueing Algorihms (MCA, algoritmi di restituzione del movimento), questo per entrambi i gradi di libertà. Si è quindi intervenuti sul modello esistente implementato in MATLAB-Simulink nello specifico blocco del motion cueing sul surge (traslazione longitudinale) e sul yaw (imbardata). Riguardo lo scale factor, è stata introdotta una metodologia per creare uno scale factor non lineare in forma esponenziale, tale da migliorare la restituzione degli impulsi meno ampi, pur rispettando i limiti fisici della piattaforma di movimento. Per quanto concerne il MCA, si sono vagliate diverse transfer function dell’algoritmo classico. La scelta finale dei MCA e la validazione del motion cueig in genere è stata effettuata mediante due esperimenti ed il giudizio dei soggetti che vi hanno partecipato. Inoltre, in virtù dei risultati del primo esperimento, si è investigata l’influenza che la strategia in merito al cambio delle marce avesse sulla percezione del movimento da parte del guidatore.

Inter-relações da variabilidade espacial da granulometria do solo e a produtividade do feijoeiro sob plantio direto

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)