Characterization of sol-gel matrices with entrapped cutinase

Dissertação para obtenção do Grau de Doutor em Engenharia Química e Bioquímica

Isolation and encapsulation of a natural colourant using green technologies

The use of natural pigments instead of synthetic colourants is receiving growing interest in the food industry. In this field, cactus pears (Opuntia spp.) have been identified to be a promising betalainic crops covering a wide coloured spectrum. The aim of this work was to develop adequate clean and mild methodologies for the isolation and encapsulation of betacyanins, from cactus pear fruits (Opuntia spp.). Firstly, two different emerging technologies, namely PLE (Pressurized Liquid Extraction) and HPCDAE (High Pressure Carbon Dioxide-Assisted Extraction), were exploited to isolation of betacyanins form cactus pear fruits. Different process conditions were tested for the maximum recovery of betacyanins. Results showed that highest extraction yields were achieved for HPCDAE and mass ratio of pressurized carbon dioxide vs. acidified water was the parameter that most affected the betacyanins extraction. At optimum conditions of HPCDAE, Opuntia spp. extract presented a total betacyanin content of 211 ± 10 mg/100 g whereas extracts obtained using conventional extraction, PLE in static and in dynamic mode presented a total betacyanin content of 85 ± 3, 191 ± 2 and 153 ± 5 mg/100 g, respectively. HPCDAE has proven to be a successful technology to extract betacyanins from Opuntia spp. fruits. Afterward, Supercritical Fluid Technology was exploited to develop lipidic particles of betalain-rich extract. A betacyanin-rich conventional extract was encapsulated by PGSS® (Particles from Gas Saturated Solutions) technique. Different process conditions were tested in order to model the encapsulation of betacyanins. The pressure had a negative effect on betacyanin encapsulation. Lower pressures leads to an increase in the betacyanin encapsulation. This effect was more pronounced at higher temperatures and lower equilibrium time. At these conditions, Opuntia spp. particles presented 64.4 ± 4.5 mg/100 g and high antioxidant capacity. When compared with the Opuntia spp. dried extract, lipidic particles contributed to a better homogenization of the pink colour after incorporation in ice cream.

Composition, abundance and aspects of temporal variation in the distribution of Anopheles species in an area of Eastern Amazonia

Introduction The diverse and complex environmental conditions of the Amazon Basin favor the breeding and development of Anopheles species. This study aimed to describe the composition, abundance and temporal frequency of Anopheles species and to correlate these factors with precipitation, temperature and relative humidity. Methods The study was conducted in the District of Coração, State of Amapá, Brazil. Samples were collected monthly during three consecutive nights, from 6:00 PM to 10:00 PM, from December 2010 to November 2011. In addition, four 12-hour collections (i.e., 6:00 PM to 6:00 AM) were performed during this period. Results A total of 1,230 Anopheles specimens were collected. In the monthly collections, Anopheles darlingi was the predominant species, followed by An. braziliensis and An. albitarsis s.l., whereas An. darlingi, An. peryassui and An. braziliensis were the most frequent species collected in the 12-hour collections. The greatest number of anophelines was collected in September (the dry season). The highest frequency of anophelines was observed for An. darlingi during September, when there were the least rainfalls of the year, along with lower relative humidity and higher temperatures. There was little variation in the abundance of this species in other months, with the exception of slight increases in February, July and August. Conclusions The major malaria vectors, An. darlingi and An. albitarsis s.l. (likely An. marajoara), were the most abundant species collected in the study area. Consequently, prevention and control measures should be taken to prevent malaria outbreaks in the District of Coração.

Durability indicators comparison for SCC and CC in tropical coastal environments

Self-compacting concrete (SCC) demands more studies of durability at higher temperatures when subjected to more aggressive environments in comparison to the conventional vibrated concrete (CC). This work aims at presenting results of durability indicators of SCC and CC, having the same water/binder relations and constituents. The applied methodologies were electrical resistivity, diffusion of chloride ions and accelerated carbonation experiments, among others, such as microstructure study, scanning electron microscope and microtomography experiments. The tests were performed in a research laboratory and at a construction site of the Pernambuco Arena. The obtained results shows that the SCC presents an average electrical resistivity 11.4% higher than CC; the average chloride ions diffusion was 63.3% of the CC; the average accelerated carbonation penetration was 45.8% of the CC; and the average open porosity was 55.6% of the CC. As the results demonstrated, the SCC can be more durable than CC, which contributes to elucidate the aspects related to its durability and consequent prolonged life cycle.

Flow cytometry analyses of calcification propensity

Dissertação de mestrado integrado em Engenharia Biomédica (área de especialização em Engenharia Clínica)

Effect of temperature on the survival and growth of freshwater prawns Macrobrachium borellii and Palaemonetes argentinus (Crustacea, Palaemonidae)

During the two-month rearing period, the effect of four water temperatures (15°C, 20°C, 25°C and 30°C) on survival rate, number of molts, and growth rate (molt increment and intermolt period) of juvenile Macrobrachium borellii Nobili, 1896 and Palaemonetes argentinus Nobili, 1901 prawns was evaluated in laboratory conditions. The two species showed some similarities in their both survival and growth pattern at different temperatures. The survival rate was highest at 20°C and 25°C, decreasing at the lowest temperature. The number of molts increased at higher temperatures, ranging the intermolt period from 22.2 days to 9.9 days, for M. borellii, and from 20.8 to 9.5 days for P. argentinus, corresponding those values to 15°C and 30°C, respectively. No difference between species was noted in the intermolt period. The size increment by molting increased significantly from 15°C to 25°C, whereas a reduction in the growth of prawns was observed at 30°C. Significant differences among temperatures were found in the slope of regressions between the size increment by molting and the cephalothorax length. M. borellii showed a significantly higher tolerance to elevated temperature and a faster growth (about twice at 25°C) than P. argentinus. These differences could provide M. borellii a competitive advantage for a better adaptation to the dynamic of freshwater environment, especially in areas with anthropogenic impact.

Estimating patterns of leaf herbivory along an altitudinal transect in NE Queensland rainforests: might global warming increase leaf herbivory in tropical rainforests?

Climate change has been taking place at unprecedented rates over the past decades. These fast alterations caused by human activities are leading to a global warming of the planet. Warmer temperatures are going to have important effects on vegetation and especially on tropical forests. Insects as well will be affected by climate change. This study tested the hypothesis that higher temperatures lead to a higher insect pressure on vegetation. Visual estimations of leaf damage were recorded and used to assess the extent of herbivory in nine 0.1ha plots along an altitudinal gradient, and therefore a temperature gradient. These estimations were made at both a community level and a species level, on 2 target species. Leaf toughness tests were performed on samples from the target species from each plot. Results showed a strong evidence of increasing insect damage along increasing temperature, with no significant effect from the leaf toughness.

Effect of temperature on different stages of Romanomermis iyengari, a mermithid nematode parasite of mosquitoes

The effect of temperature (20 degrees-35 degrees C) on different stages of Romanomermis iyengari was studied. In embryonic development, the single-cell stage eggs developed into mature eggs in 4.5-6.5 days at 25-35 degrees C but, required 9.5 days at 20 degrees C. Complete hatching occurred in 7 and 9 days after egg-laying at 35 and 30 degrees C, respectively. At 25 and 20 degrees C, 85-96 of the eggs did not hatch even by 30th day. Loss of infectivity and death of the preparasites occurred faster at higher temperatures. The 50 survival durations of preparasites at 20 and 35 degrees C were 105.8 and 10.6 hr respectively. They retained 50 infectivity up to 69.7 and 30.3 hr. The duration of the parasitic phase increased as temperature decreased. Low temperature favoured production of a higher proportion of females which were also larger in size. The maximum time taken for the juveniles to become adults was 14 days at 20 degrees C and the minimum was 9 days at 35 degrees C. Oviposition began earlier at higher temperature than at lower temperature. However, its fecundic period was shorter at 20 degrees C than at 35 degrees C indicating enhanced rate of oviposition at 20 degrees C. Fecundity was adversely affected at 20 degrees C and 35 degrees C. It is shown that the temperature range of 25 degrees-30 degrees C favours optimum development of R. iyengari.

Low-pressure, water-assisted anatexis of basic dykes in a contact metamorphic aureole, Fuerteventura (Canary Islands): oxygen isotope evidence for a meteoric fluid origin

Migmatites produced by low-pressure anatexis of basic dykes are found in a contact metamorphic aureole around a pyroxenite-gabbro intrusion (PX2), on Fuerteventura. Dykes outside and inside the aureole record interaction with meteoric water, with low or negative delta O-18 whole-rock values (+0.2 to -3.4 parts per thousand), decreasing towards the contact. Recrystallised plagioclase, diopside, biotite and oxides, from within the aureole, show a similar evolution with lowest delta O-18 values (-2.8, -4.2, - 4.4 and -7.6 parts per thousand, respectively) in the migmatite zone, close to the intrusion. Relict clinopyroxene phenocrysts preserved in all dykes, retain typically magmatic delta O-18 values up to the anatectic zone, where the values are lower and more heterogeneous. Low delta O-18 values, decreasing towards the intrusion, can be ascribed to the advection of meteoric water during magma emplacement, with increasing fluid/rock ratios (higher dyke intensities towards the intrusion acting as fluid-pathways) and higher temperatures promoting increasing exchange during recrystallisation.

Vaporization behaviour and some thermodynamic properties of the Pd-In, Pd-Pb, Pd-Sn systems

In this study, the vaporization behaviour of solid Pd-rich phases in the Pd-Pb, Pd-In and Pd-Sn systems was investigated by Knudsen-effusion-cell coupled with mass-spectrometry. The Pb, Pd, In vapor pressures [no Sn(g) has been detected in the vapor of Pd-Sn system] were evaluated in the temperatures range 1190-1563 K from the ion intensities measured over two-phases regions. Thermodynamic quantities were derived from vapor pressure data. In particular, for the Pd-Sn binary, the intermediate phase Pd7Sn2, the existence of which has been recently proposed, has been studied here for the first time. Furthermore, preliminary thermochemical data are presented for the diatomic intermetallic molecules PdSn and PdPb, which have been for the first time identified in the vapors in equilibrium over liquid solutions of appropriate composition at higher temperatures (1935-2025 K). (C) 2000 Elsevier Science Ltd. All rights reserved.

Sandflies (Diptera: Psychodidae) from caves of the quartzite Espinhaço Range, Minas Gerais, Brazil

This study investigated the sandfly fauna of two quartzite caves in the Espinhaço Mountain Range, located in the municipality of Diamantina, state Minas Gerais. From August 2010-July 2011, entomological sampling was performed in the caves of Salitre and Monte Cristo with two HP light traps exposed in the photic and aphotic zones of each cave. The sandfly fauna consisted of 17 species, among which Lutzomyia cipoensis was predominant (54.76%). The male/female ratio in the total captures was 1:2.5. The aphotic zone showed the highest frequency of specimens captured (65%). A greater density of sandflies occurred during the summer (January-February), coinciding with the period of higher temperatures, humidity and rainfall. The presence of Lutzomyia longipalpis, Lutzomyia whitmani and Lutzomyia pessoai, proven or suspected vectors of leishmaniasis, is of concern because the area is visited by many tourists.

7

Climate change data and predictions for the Himalayas are very sparse and uncertain, characterized by a ?Himalayan data gap? and difficulties in predicting changes due to topographic complexity. A few reliable studies and climate change models for Nepal predict considerable changes: shorter monsoon seasons, more intensive rainfall patterns, higher temperatures, and drought. These predictions are confirmed by farmers who claim that temperatures have been increasing for the past decade and wonder why the rains have ?gone mad.? The number of hazard events, notably droughts, floods, and landslides are increasing and now account for approximately 100 deaths in Nepal annually. Other effects are drinking water shortages and shifting agricultural patterns, with many communities struggling to meet basic food security before climatic conditions started changing. The aim of this paper is to examine existing gaps between current climate models and the realities of local development planning through a case study on flood risk and drinking water management for the Municipality of Dharan in Eastern Nepal. This example highlights current challenges facing local-level governments, namely, flood and landslide mitigation, providing basic amenities ? especially an urgent lack of drinking water during the dry season ? poor local planning capacities, and limited resources. In this context, the challenge for Nepal will be to simultaneously address increasing risks caused by hazard events alongside the omnipresent food security and drinking water issues in both urban and rural areas. Local planning is needed that integrates rural development and disaster risk reduction (DRR) with knowledge about climate change considerations. The paper concludes with a critical analysis of climate change modeling and the gap between scientific data and low-tech and low capacities of local planners to access or implement adequate adaptation measures. Recommendations include the need to bridge gaps between scientific models, the local political reality and local information needs.

Dynamics of the control of Aedes (Stegomyia) aegypti Linnaeus (Diptera, Culicidae) by Bacillus thuringiensis var israelensis, related with temperature, density and concentration of insecticide

The dynamics of the control of Aedes (Stegomyia) aegypti Linnaeus, (Diptera, Culicidae) by Bacillus thuringiensis var israelensis has been related with the temperature, density and concentration of the insecticide. A mathematical model for biological control of Aedes aegypti with Bacillus thuringiensis var israelensis (Bti) was constructed by using data from the literature regarding the biology of the vector. The life cycle was described by differential equations. Lethal concentrations (LC50 and LC95) of Bti were determined in the laboratory under different experimental conditions. Temperature, colony, larvae density and bioinsecticide concentration presented marked differences in the analysis of the whole set of variables; although when analyzed individually, only the temperature and concentration showed changes. The simulations indicated an inverse relationship between temperature and mosquito population, nonetheless, faster growth of populations is reached at higher temperatures. As conclusion, the model suggests the use of integrated control strategies for immature and adult mosquitoes in order to achieve a reduction of Aedes aegypti.

Partial melting of basic dykes in the contact aureoles of two shallow-level, gabbro-pyroxenite intrusions, Fuerteventura

THESIS ABSTRACT Low-pressure anatexis of basic dykes gave rise to unusual, zebra-like migmatites, in the contact metamorphic aureoles of two layered gabbro-pyroxenite intrusions, PXl and PX2, in the root zone of an ocean island, Fuerteventura Basal Complex (Canary Islands). This thesis focuses on the understanding of processes attributing to the partial melting and formation of these migmatites, characterised by a dense network of closely spaced, millimetre-wide leucocratic segregations with perfectly preserved igneous textures. The presence of fluids are required to decrease the solidus of basic igneous lithologies, to allow partial melting in such aloes-pressure (1-2 kb) environment. An oxygen isotope study was thus carried out on dykes inside and beyond the PX2 aureole, in order to decipher the nature and origin of such fluids. Low or negative δ18O values were obtained for whole rocks and mineral-separates, decreasing towards the contact, with the intrusion itself retaining fairly high values. This trend has been attributed to the advection of meteoric water during magma emplacement, with increasing fluid/rock ratios (higher dyke intensities towards the intrusion acting as fluid-pathways) and higher temperatures promoting increasing exchange during recrystallisation. A comparison of whole rock and mineral major- and trace- element data allowed the redistribution of elements .between different mineral phases and generations, during contact metamorphism and partial melting to be assessed. Certain trace-elements, e.g. Zr, Hf, Y, and REEs, were internally redistributed during contact metamorphic recrystallisation, causing- the enrichment of neocrystallised diopsides compared to relict phenocrysts. This has been assigned to the liberation of trace elements on the breakdown of primary minerals, kaersutite and sphene, on entering the thermal aureole. Major and trace element compositions of minerals in migmatite melanosomes and leucosomes are almost identical, pointing to a syn- or post- solidus reequilibration on cooling of the migmatite terrain. The mineralogical, textural and geochemical evolution of dykes in a contact metamorphic aureole, is recorded around an apophysis of the PX1 intrusion, where there is evidence of incipient partial melting. Hydrothermal mineral pseudomorphs in the outer parts of the aureole are progressively replaced by dry mineral assemblages, with increasingly recrystallised diopside and evidence of partial melting -the extent of which varies from one lithology to another. The appearance of more mafic lithologies towards the intrusion, with lower whole rock SiO2 and mobile element abundances, e.g. Rb, Cs, K, has been explained by the migration and accumulation of feldspathic material into leucosomes outside the samples. A micro-structural study of leucosomes and leucocratic pods, with the aid of high-resolution X-ray computed micro-tomography (HRXµCT), allowing the visualization and quantification of shapes and orientations, was carried out in order to better understand the processes of melt segregation in the PX1 aureole. Leucocratic pods, representing former amygdales, are considered as natural strain ellipsoids. Their short axes are oriented perpendicular to leucosome planes, which sub-parallel the intrusive contact. Leucosomes thus effectively represent foliation planes. This implies that the direction of maximum shortening, during migmatisation, was perpendicular to the orientation of leucosomes, contradicting earlier models that suggest leucosomes represent tension veins. RESUME DE LA THESE Un phénomène rare de fusion partielle de filons basiques à basse pression a été étudié dans les auréoles de contact de deux intrusions litées de gabbro-pyroxénite, PX1 et PX2, localisées dans le soubassement de l'île volcanique de Fuerteventura aux Canaries. Cette anatexie a engendré des migmatites finement zébrées d'aspect très inhabituel, dont les processus de formation ont été étudiés dans le présent travail. Ces roches sont caractérisées par un réseau dense de veinules leucocrates d'épaisseur millimétrique, dont les textures ignées sont parfaitement préservées. La fusion partielle de roches basiques à basse pression (1-2 kbar) requiert la présence d'eau afin d'abaisser le solidus du système à des températures géologiquement réalistes. Une étude comparative des isotopes de l'oxygène a ainsi été menée sur des filons respectivement affectés et non affectés par le métamorphisme de contact, afin de confirmer la présence de ces fluides, de déterminer l'importance de leur interaction avec les roches et leur origine. Des valeurs de δ180 basses ou négatives ont été mesurées sur roche totale et minéraux séparés, décroissantes en direction du contact, alors que l'intrusion elle-même a conservé des valeurs élevées. Ce gradient a été attribué à l'advection d'eau météorique durant la mise en place du magma, les températures les plus élevées favorisant d'autant plus la circulation des fluides et les échanges isotopiques durant la recristallisation des roches. Cette recristallisation engendré une redistribution chimique complète des éléments entre les différentes générations de minéraux résultant du métamorphisme de contact et de l'anatexie, mise en évidence par microanalyse. Certains éléments traces comme Zr, Hf, Y et les REE ont été concentrés dans le diopside néoformé consécutivement à la déstabilisation de minéraux primaires riches en ces éléments comme la kaersutite ou le sphène. Les compositions en éléments majeurs et traces des minéraux des mélanosomes et leucosomes des migmatites sont pratiquement identiques, indiquant une rééquilibration syn- à postsolidus lors du refroidissement de l'auréole de contact. La transformation progressive des filons basiques au niveau de leur minéralogie, textures et composition chimique a pu être observée en détail à l'approche du contact d'une apophyse de l'intrusion PX1. La paragenèse magmatique initiale n'est jamais préservée, les faciès les plus distants du contact étant constitués d'un assemblage pseudomorphique hydrothermal. Ce dernier est progressivement remplacé par des assemblages anhydres incluant du diopside néoformé, puis apparaissent les premiers signes de fusion partielle, dont l'importance varie fortement d'une lithologie à l'autre. L'apparition de faciès plus basiques en direction du contact, avec des teneurs réduites en SiO2 et en éléments incompatibles tels Rb, Cs, K, a été attribuée à l'échappement de leucosomes feldspathiques hors du système. Une étude microstructurale de la distribution spatiale du matériel leucocrate au sein des migmatites par microtomographie X de haute résolution (HRXµCT) a été menée pour mieux comprendre les processus de ségrégation des liquides dans l'auréole de PX1. De petites entités ovoïdes, représentant d'anciennes structures amygdalaires au sein des filons, ont été considérées comme des ellipsoïdes marqueurs de la déformation finie. Leur petit axe est orienté perpendiculairement aux plans définis par les leucosomes, eux-mêmes subparallèles au contact intrusif. Les leucosomes matérialisent donc des plans de clivage. Ainsi, la direction de raccourcissement maximum durant la fusion partielle était perpendiculaire à l'orientation des leucosomes, contrairement à ce qui a été dit dans de précédentes publications, qui suggéraient que les leucosomes représentaient des veines de tension. RESUME DE LA THESE (POUR LE GRAND PUBLIC) L'observation directe du soubassement d'une île volcanique est une occasion rare, accessible dans le «complexe de base » de l'île canarienne de Fuerteventura. Ce dernier a enregistré divers phénomènes magmatiques, métamorphiques et de fusion partielle induits par l'intrusion répétée de magmas alimentant des appareils volcaniques sus jacents, sous forme de petits plutons, essaims de filons et complexes annulaires de gabbros alcalins, pyroxénites, syénites et carbonatites. Dans ce contexte de flux de chaleur élevé, des filons basiques ont subi une fusion partielle au contact de deux intrusions de gabbro-pyroxénite, un phénomène extrêmement rare à une profondeur aussi réduite, estimée à quelque 3-6 km. Les produits de cette fusion partielle sont des liquides très riches en feldspath, concentrés en un réseau dense de veinules blanches (leucosomes) au sein du matériau résiduel sombre non fondu (mélanosome) pour former ce qu'on appelle des migmatites. Outre les aspects pétrologiques liés à la formation de ces migmatites, l'intérêt majeur du phénomène réside dans le fait qu'il puisse représenter la source des magmas évolués parfois observés sur les îles océaniques. A des pressions aussi faibles que dans le soubassement de Fuerteventura (1-2 Kbar), la présence de fluides abondants est nécessaire pour abaisser la température de début de fusion des roches (solidus) à des valeurs géologiquement réalistes. Des expériences ont montré que même en présence de plusieurs %-poids d'eau, une température de 1000°C était encore nécessaire pour obtenir une proportion de liquide équivalente à celle observée sur le terrain, soit 25%. Or les magmas alcalins des îles océaniques, bien qu'hydratés, n'en contiennent de loin pas autant, ce qui implique une source d'eau externe. Une étude isotopique de l'oxygène a été entreprise afin de tester cette hypothèse. Les valeurs obtenues en 5180 sont basses ou négatives et indiquent l'influence d'eau d'origine météorique. Cette eau de pluie se serait infiltrée le long des filons depuis la surface du volcan et les aurait complètement hydrothermalisés en profondeur (situation encore visible à l'extérieur de l'auréole de contact), leur permettant ainsi de stocker l'eau nécessaire à leur fusion partielle ultérieure. L'interaction entre eau de pluie et filons a été d'autant plus importante que ces derniers étaient proches du contact avec l'intrusion, ce qui suggère que la circulation de ces eaux et leur interaction avec les roches a été favorisée par la chaleur fournie par l'intrusion elle-même. Un autre aspect de ce travail s'est focalisé sur la redistribution des éléments traces au sein des minéraux des filons basiques durant le métamorphisme de contact et la fusion partielle. Ainsi, le pyroxène de seconde génération est-il sensiblement enrichi en traces telles Zr, Hf, Y et les terres rares, par rapport au pyroxène magmatique originel, en relation avec la déstabilisation de minéraux primaires riches en ces éléments tels le sphène et la kaersutite. Cependant, les compositions en éléments majeurs et traces des minéraux recristallisés des migmatites sont pratiquement les mêmes dans les leucosomes et les mélanosomes, suggérant une rééquilibration chimique complète durant le refroidissement de ces lithologies. Si certaines migmatites se sont comportées en système chimiquement fermé (hormis l'eau météorique), d'autres filons ont manifestement perdu une partie de leurs leucosomes, ainsi qu'en témoigne leur composition progressivement appauvrie en silice et autres éléments incompatibles mobiles, tels K et Rb à l'approche du contact de l'intrusion. Parallèlement à cette évolution chimique, les paragenèses hydrothermales distantes du contact sont progressivement remplacées par des paragenèses anhydres, puis par l'apparition des premiers leucosomes, tandis que les textures magmatiques initiales sont complètement effacées au profit d'une combinaison de textures magmatique dans les leucosomes et en mosaïque dans les mélanosomes. Enfin, la distribution spatiale des liquides de fusion partielle a été étudiée par microtomographie X de haute résolution, dans des filons contenant des entités ovoïdes leucocrates, sans doute d'anciennes amygdales à zéolites. Ces dernières ont été considérées comme des ellipsoïdes de la déformation finie. L'orientation de leur petit axe, perpendiculaire au plan défini par les veinules de leucosomes, indique que ces derniers représentent des plans de clivage perpendiculaires à la direction de raccourcissement maximum. Ainsi, la ségrégation des liquides de fusion partielle se serait faite dans les plans de compression et non dans des plans de dilatation, contrairement à ce que laisserait penser le sens commun.

Nanosized Nb-TiO2 gas sensors derived from alkoxides hydrolization

Nanocrystalline TiO2 modified with Nb has been produced through the sol-gel technique. Nanopowders have been obtained by means of the hydrolysis of pure alkoxides with deionized water and peptization of the resulting hydrolysate with diluted acid nitric at 100 C. The addition of Nb stabilizes the anatase phase to higher temperatures. XRD spectra of the undoped and the Nb-doped samples show that the undoped sample has been almost totally converted to rutile at 600 C, meanwhile the doped samples present still a low percentage of rutile phase. Nanocrystalline powders stabilized at 600 C with grain sizes of about 17 nm have successfully been synthesized by the addition of Nb with a concentration of 2% at., which appears to be an adequate additive concentration to improve the gas sensor performances, such as it is suggested by the catalytic conversion efficiency experiments performed from FTIR measurements. FTIR absorbance spectra show that catalytic conversion of CO occurs at lower temperatures when niobium is introduced. The electrical response of the films to different concentrations of CO and ethanol has been monitored in dry and wet environments in order to test the influence of humidity in the sensor response. The addition of Nb decreases the working temperature and increases the stability of the layers. Also, large enhancement of the response time is obtained even with lower working temperatures. Moreover, humidity effects on the gas sensor response toward CO and ethanol are less important in Nb-doped samples than in the undoped ones.