101 resultados para Fumigation
Resumo:
BACKGROUND: The recent development of very high resistance to phosphine in rusty grain beetle, Cryptolestes ferrugineus (Stephens), seriously threatens stored-grain biosecurity. The aim was to characterise this resistance, to develop a rapid bioassay for its diagnosis to support pest management and to document the distribution of resistance in Australia in 20072011. RESULTS: Bioassays of purified laboratory reference strains and field-collected samples revealed three phenotypes: susceptible, weakly resistant and strongly resistant. With resistance factors of > 1000 x , resistance to phosphine expressed by the strong resistance phenotype was higher than reported for any stored-product insect species. The new time-to-knockdown assay rapidly and accurately diagnosed each resistance phenotype within 6 h. Although less frequent in western Australia, weak resistance was detected throughout all grain production regions. Strong resistance occurred predominantly in central storages in eastern Australia. CONCLUSION: Resistance to phosphine in the rusty grain beetle is expressed through two identifiable phenotypes: weak and strong. Strong resistance requires urgent changes to current fumigation dosages. The development of a rapid assay for diagnosis of resistance enables the provision of same-day advice to expedite resistance management decisions. (c) 2012 Commonwealth of Australia. Published by John Wiley & Sons, Ltd.
Resumo:
The red flour beetle is a cosmopolitan pest of stored grain and stored grain products. The pest has developed resistance to phosphine, the primary chemical used for its control. The reproductive output of survivors from a phosphine treatment is an important element of resistance development but experimental data are lacking. We exposed mated resistant female beetles to 0.135 mg/L of phosphine for 48 h at 25°C. Following one week of recovery we provided two non-exposed males to half of the phosphine exposed females and to half of the non-exposed control females. Females that had been exposed produced significantly fewer offspring than non-exposed females. Females that remained isolated produced significantly fewer offspring than both exposed females with access to males and non-exposed controls (P<0.05). Some females were permanently damaged from exposure to phosphine and did not reproduce even when given access to males. We also examined the additional effects of starvation prior to phosphine exposure on offspring production. Non-exposed starved females experienced a small reduction in mean offspring production in the week following starvation, followed by a recovery in the second week. Females that were starved and exposed to phosphine demonstrated a very significant reduction in offspring production in the first week following exposure which remained significantly lower than that of starved non-exposed females (P<0.05). These results demonstrate a clear sublethal effect of phosphine acting on the female reproductive system and in some individuals this can lead to permanent reproductive damage. Pest population rebound after a fumigation may be slower than expected which may reduce the rate of phosphine resistance development. The results presented strongly suggest that phosphine resistance models should include sublethal effects. © 2012 Ridley et al.
Resumo:
The lesser grain borer Rhyzopertha dominica (F.) is one of the most destructive insect pests of stored grain. This pest has been controlled successfully by fumigation with phosphine for the last several decades, though strong resistance to phosphine in many countries has raised concern about the long term usefulness of this control method. Previous genetic analysis of strongly resistant (SR) R. dominica from three widely geographically dispersed regions of Australia, Queensland (SRQLD), New South Wales (SRNSW) and South Australia (SRSA), revealed a resistance allele in the rph1 gene in all three strains. The present study confirms that the rph1 gene contributes to resistance in a fourth strongly resistant strain, SR2(QLD), also from Queensland. The previously described rph2 gene, which interacts synergistically with rph1 gene, confers strong resistance on SRQLD and SRNSW. We now provide strong circumstantial evidence that weak alleles of rph2, together with rph1, contribute to the strong resistance phenotypes of SRSA and SR2(QLD). To test the notion that rph1 and rph2 are solely responsible for the strong resistance phenotype of all resistant R. dominica, we created a strain derived by hybridising the four strongly resistant lines. Following repeated selection for survival at extreme rates of phosphine exposure, we found only slightly enhanced resistance. This suggests that a single sequence of genetic changes was responsible for the development of resistance in these insects.
Resumo:
Phosphine is the only economically viable fumigant for routine control of insect pests of stored food products, but its continued use is now threatened by the world-wide emergence of high-level resistance in key pest species. Phosphine has a unique mode of action relative to well-characterised contact pesticides. Similarly, the selective pressures that lead to resistance against field sprays differ dramatically from those encountered during fumigation. The consequences of these differences have not been investigated adequately. We determine the genetic basis of phosphine resistance in Rhyzopertha dominica strains collected from New South Wales and South Australia and compare this with resistance in a previously characterised strain from Queensland. The resistance levels range from 225 and 100 times the baseline response of a sensitive reference strain. Moreover, molecular and phenotypic data indicate that high-level resistance was derived independently in each of the three widely separated geographical regions. Despite the independent origins, resistance was due to two interacting genes in each instance. Furthermore, complementation analysis reveals that all three strains contain an incompletely recessive resistance allele of the autosomal rph1 resistance gene. This is particularly noteworthy as a resistance allele at rph1 was previously proposed to be a necessary first step in the evolution of high-level resistance. Despite the capacity of phosphine to disrupt a wide range of enzymes and biological processes, it is remarkable that the initial step in the selection of resistance is so similar in isolated outbreaks.
Resumo:
Long-fallow disorder is expressed as exacerbated deficiencies of phosphorus (P) and/or zinc (Zn) in field crops growing after long periods of weed-free fallow. The hypothesis that arbuscular-mycorrhizal fungi (AMF) improve the P and Zn nutrition, and thereby biomass production and seed yield of linseed (Linum usitatissimum) was tested in a field experiment. A factorial combination of treatments consisting of +/- fumigation, +/- AMF inoculation with Glomus spp., +/- P and +/- Zn fertilisers was used on a long-fallowed vertisol. The use of such methods allowed an absolute comparison of plants growing with and without AMF in the field for the first time in a soil disposed to long-fallow disorder. Plant biomass, height, P and Zn concentrations and contents, boll number and final seed yield were (a) least in fumigated soil with negligible AMF colonisation of the roots, (b) low initially in long-fallow soil but increased with time as AMF colonisation of the roots developed, and (c) greatest in soil inoculated with AMF cultures. The results showed for the first time in the field that inflows of both P and Zn into linseed roots were highly dependent on %AMF-colonisation (R-2 = 0.95 for P and 0.85 for Zn, P < 0.001) in a soil disposed to long-fallow disorder. Relative field mycorrhizal dependencies without and with P+Zn fertiliser were 85 % and 86 % for biomass and 68 % and 52 % for seed yield respectively. This research showed in the field that AMF greatly improved the P and Zn nutrition, biomass production and seed yield of linseed growing in a soil disposed to long-fallow disorder. The level of mycorrhizal colonisation of plants suffering from long-fallow disorder can increase during the growing season resulting in improved plant growth and residual AMF inoculum in the soil, and thus it is important for growers to recognise the cause and not terminate a poor crop prematurely in order to sow another. Other positive management options to reduce long fallows and foster AMF include adoption of conservation tillage and opportunity cropping.
Resumo:
Apples at 24 ± 2 °C were heated in a pilot scale hot air assisted (40 °C) continuous pentagonal microwave system, to evaluate the effectiveness of this treatment on insect mortality (variety Mutsu) and fruit quality (variety Granny Smith). An average temperature of 53.4 ± 1.3 °C at core, bottom and flesh of the apple was recorded at the end of the treatment. One hundred percent mortality of the most tolerant stage of Queensland fruit fly (Bactrocera tryoni, Froggatt) and Jarvis's fruit fly (Bactrocera jarvisi, Tryon), were observed when the Mortality value (M52, equivalent time of isothermal treatment at 52 °C) at the slowest heating point applicable for each experiment was ≥ 50 min and ≥ 37 min, respectively. Results showed that microwave heat treatment is effective for insect disinfestation without any adverse impact on total soluble solids, flesh or peel firmness of the treated apples. The treated apples recorded a significantly higher pH and lower ion leakage than the untreated apples after 3 or 4 weeks. Therefore, the microwave heat treatment has the potential to be developed as an alternative chemical free quarantine treatment against economically significant insect pests. Industrial relevance Hot air assisted microwave heating of fruits and vegetables, is more cost effective compared to vapour heat treatment and ionising radiation for disinfestation of insects. Microwave treatment is environmentally friendly compared to fumigation and chemical treatments. Hot air assisted microwave disinfestation can be performed at farms or centralised pack houses since the capital cost would be comparatively lower than vapour heat or ionising radiation treatments.
Resumo:
BACKGROUND Our aim was to ascertain the potential of sulfuryl fluoride (SF) as an alternative fumigant to manage phosphine-resistant pests. We tested the susceptibility of all life stages of red flour beetle, Tribolium castaneum (Herbst), to SF and assessed the presence of cross-resistance to this fumigant in phosphine-resistant strains of this species. RESULTS Analysis of dose–response data indicated that the egg was the stage most tolerant to SF under a 48 h exposure period. At LC50, eggs were 29 times more tolerant than other immature stages and adults, and required a relatively high concentration of 48.2 mg L−1 for complete mortality. No significant differences in tolerance to SF were observed among the three larval instars, pupae and adults, and all of these stages were controlled at a low concentration of 1.32 mg L−1. Phosphine-resistant strains did not show cross-resistance to SF. CONCLUSION Our research concluded that the current maximum registered rate of SF, 1500 gh m−3, is adequate to control all the post-embryonic life stages of T. castaneum over a 48 h fumigation period, but it will fail to achieve complete mortality of eggs, indicating the risk of some survival of eggs under this short exposure period. As there is no cross-resistance to SF in phosphine-resistant insects, it will play a key role in managing phosphine resistance in stored-grain insect pests. © 2014 Commonwealth of Australia. Pest Management Science © 2014 Society of Chemical Industry
Resumo:
Sulfuryl fluoride (SF) has been developed as a fumigant for control of insect pests in stored grain. However, there is very limited information on the sorption behaviour of this fumigant, which can be critical to its bioactivity, application and potential for residues. We undertook a comprehensive laboratory study of the sorption and desorption of SF by wheat (bread and durum), flour and semolina at 15, 25 and 35 °C, moisture contents 12% and 15%, and concentration × time combinations at CT = 1500 mgh/L (4.167 mg/L × 360 h, 8.928 mg/L × 168 h and 31.25 mg/L × 48 h). At each dosage, sorption rate increased as commodity temperature and moisture content increased. The highest rates of sorption occurred at 35 °C and 15% m.c., and lowest rates at 15 °C and 12% m.c., and the rate was independent of initial concentration. Sorption followed first order reaction kinetics described by the exponential decay equation, Ct = C0·e−k*t, where k is the sorption rate constant. The most important factors determining the rate of sorption were commodity particle size (exposed surfaces) and temperature. Little sorption of fumigant occurred within the first 24 h whereas longer fumigation times resulted in significant sorption. Unbound SF was rapidly lost from the commodity upon aeration with no further desorption detected under any of the test conditions.
Resumo:
Phosphine (PH3) fumigation is the primary method worldwide for controlling insect pests of stored commodities. Over-reliance on phosphine, however, has led to the emergence of strong resistance. Detailed genetic studies previously identified two loci, rph1 and rph2, that interact synergistically to create a strong resistance phenotype. We compared the genetics of phosphine resistance in strains of Rhyzopertha dominica and Tribolium castaneum from India and Australia, countries having similar pest species but widely differing in pest management practices. Sequencing analysis of the rph2 locus, dihydrolipoamide dehydrogenase (dld), identified two structurally equivalent variants, Proline49>Serine (P49S) in one R. dominica strain and P45S in three strains of T. castaneum from India. These variants of the DLD protein likely affect FAD cofactor interaction with the enzyme. A survey of insects from storage facilities across southern India revealed that the P45/49S variant is distributed throughout the region at very high frequencies, in up to 94% of R. dominica and 97% of T. castaneum in the state of Tamil Nadu. The abundance of the P45/49S variant in insect populations contrasted sharply with the evolutionary record in which the variant was absent from eukaryotic DLD sequences. This suggests that the variant is unlikely to provide a strong selective advantage in the absence of phosphine fumigation.
Resumo:
Fan forced injection of phosphine gas fumigant into stored grain is a common method to treat infestation by insects. For low injection velocities the transport of fumigant can be modelled as Darcy flow in a porous medium where the gas pressure satisfies Laplace's equation. Using this approach, a closed form series solution is derived for the pressure, velocity and streamlines in a cylindrically stored grain bed with either a circular or annular inlet, from which traverse times are numerically computed. A leading order closed form expression for the traverse time is also obtained and found to be reasonable for inlet configurations close to the central axis of the grain storage. Results are interpreted for the case of a representative 6m high farm wheat store, where the time to advect the phosphine to almost the entire grain bed is found to be approximately one hour.
Resumo:
The object of this investigation is to devise a rapid, fairly accurate, colorimetric analysis for HCN to be used in field work for determining instantaneous concentrations of the gas under fumigating canvas. A large amount of money is expended yearly by the citrus industry of this state in attempting to control and to eradicate the scale pests. Although fumigation with HCN has been practiced tor many years, the progress made has been anything but satisfactory. The greater portion of the work has always been carried on by contractors, who in a large number of cases have been very unscrupulous. The materials and labor are very expensive and the growers have been satisfied to adhere to beaten paths and hope for the best results on scale kill with the least attendant foliage injury. One familiar with fumigating, either from the grower's or the operator's viewpoint, knows that very widely varying results are obtained, even under what are apparently identical condition. Even after discounting for the dishonesty of some operators and the prejudices of the grower, there is still a large variance between desired or expected results and those actually obtained.
Resumo:
As indústrias farmacêuticas que utilizam salas limpas, em seus processos produtivos, devem controlar ao máximo o nível de contaminantes microbiológicos, baseada na legislação RDC 210 que determina o cumprimento das diretrizes estabelecidas no Regulamento Técnico das Boas Práticas para a Fabricação de Medicamentos. Diante deste cenário, a proposta deste trabalho é avaliar o processo de fumigação com o reagente formaldeído, para a limpeza e desinfecção de salas limpas do Instituto de Tecnologia de Imunobiológicos Bio-Manguinhos. Então, foram desenvolvidas as seguintes etapas: diagnóstico com as indústrias farmacêuticas para traçar um perfil quanto ao uso da fumigação; quantificação de resíduos gerados; avaliação da exposição dos operadores ao formaldeído que é cancerígeno e acompanhamento dos resultados do monitoramento ambiental do ar e de superfícies, inicialmente na sala limpa do SEFBC, cuja atividade principal é a formulação de vacinas bacterianas e biofármacos, após a implantação do espaçamento da fumigação. Os resultados discutidos na presente dissertação mostraram, que a maior parte das indústrias farmacêuticas, não realiza a desinfecção por intermédio da fumigação e que o resíduo gerado neste processo é o mais crítico. E, sobretudo, o monitoramento microbiológico do ar e de superfícies da sala limpa do SEFBC, a partir da metodologia adotada de espaçamento da fumigação, comprovou que não é necessário o emprego deste processo de forma rotineira, para garantir os níveis exigidos de limpeza e desinfecção da respectiva área
Resumo:
Im Vordergrund der Arbeit stand die Erfassung der mikrobiellen Biomasse bzw. Residualmasse an der Wurzeloberfläche, im Rhizosphärenboden und im umgebenden Boden. Durch den Vergleich von verschiedenen Methoden zur Erfassung der mikrobiellen Biomasse wurden die Gehalte von pilzlichem und bakteriellem Kohlenstoff an der Rhizoplane und in der Rhizosphäre quantifiziert. Dabei wurde die Fumigations-Extraktions-Methode zur Erfassung der mikrobiellen Biomasse eingesetzt. Ergosterol diente als Indikator für die pilzliche Biomasse und die Aminozucker Glucosamin und Muraminsäure sollten Aufschluss geben über die bakterielle und pilzliche Biomasse bzw. Residualmasse in den drei Probenfraktionen. Dazu wurden Umrechnungsfaktoren erstellt, die zur Berechnung des bakteriellen und pilzlichen Kohlenstoffs aus den Gehalten von Muraminsäure und Pilz-Glucosamin dienten. Die Bestimmung von Aminozuckern wurde insoweit modifiziert, dass sowohl in Boden- als auch in Wurzelhydrolysaten die Messung von Glucosamin, Galactosamin, Muraminsäure und Mannosamin gleichzeitig als automatisiertes Standardverfahren mit Hilfe der HPLC erfolgen konnte. Es wurden drei Gefäßversuche durchgeführt: Im ersten Versuch wurde der Einfluss der Pflanzenart auf die mikrobielle Besiedlung der Wurzeloberflächen untersucht. Dabei wurden Wurzeln und Rhizosphärenboden von 15 verschiedenen Pflanzenarten miteinander verglichen. Im zweiten Versuch stand der Einfluss der mikrobiellen Biomasse eines Bodens auf die mikrobielle Besiedlung von Wurzeloberflächen im Vordergrund. Deutsches Weidelgras (Lolium perenne L.) wurde auf sieben verschiedenen Böden angezogen. Bei den Böden handelte es sich um sechs Oberböden, die sich hinsichtlich des Bodentyps und der Bewirtschaftungsform voneinander unterschieden, und einen Unterboden. Im dritten Versuch wurde die mikrobielle Besiedlung von Wurzeln nach teilweiser und vollständiger Entfernung der oberirdischen Biomasse beobachtet. Welsches Weidelgras (Lolium multiflorum Lam.) wurde 24 Tage nach der Aussaat beschnitten. Anschließend wurde über einen Versuchszeitraum von acht Tagen die mikrobielle Besiedlung an den Wurzeln und in den Bodenfraktionen bestimmt. Es bestätigte sich, dass der Einfluss der einzelnen Pflanzenart von entscheidender Bedeutung für die mikrobielle Besiedlung von Wurzeln ist. Bei fast allen Pflanzen wurde die mikrobielle Biomasse an den Wurzeln von Pilzen dominiert. Das Verhältnis von pilzlichem zu bakteriellem Kohlenstoff an den Wurzeln der 15 Pflanzenarten lag im Mittel bei 2,6. Bei der Betrachtung verschiedener Böden zeigte sich, dass die mikrobielle Besiedlung in tieferen Bodenschichten signifikant niedriger ist als in den Oberböden. Dabei war der Pilzanteil an der mikrobiellen Biomasse im Unterboden deutlich erhöht. Der Vergleich der Oberböden untereinander ergab, dass sowohl der Bodentyp als auch die Bewirtschaftungsform einen signifikanten Einfluss auf mikrobielle Besiedlung ausüben. Durch die teilweise oder vollständige Entfernung der oberirdischen Biomasse wurde eine Veränderung der mikrobiellen Besiedlung an den Wurzeln beobachtet. Das Verhältnis von pilzlichem zu bakteriellem Kohlenstoff sank in dem Versuchszeitraum von 2,5 auf 1,4. Dabei war die Förderung der Pilze in der Variante mit teilweise entfernter oberirdischer Biomasse relativ größer als in der Variante mit vollständig entfernter oberirdischer Biomasse. Entgegen der weit verbreiteten Annahme, dass bei den wurzelbesiedelnden Mikroorganismen die Bakterien gegenüber den Pilzen dominieren, zeigten die Ergebnisse ein gegensätzliches Bild. In allen drei Versuchen ergab sich gleichermaßen, dass sowohl im Boden als auch an den Wurzeln die Pilze gegenüber den Bakterien dominieren.
Resumo:
This training video is intended to familiarise researchers and technicians, working with potentially airborne pathogens, on the correct and safe use of Microbiological Safety Cabinets. The video also provides instruction on cleaning, disinfection and fumigation regimes; maintenance and testing regimes; and commissioning and decommissioning requirements of such Local Exhaust Ventilation (LEV) systems. It is in Windows Media Video format which will require a free media player such as Windows Media Player or VLC Media Player (http://www.videolan.org/vlc/) to watch.
Resumo:
We have examined the contributions sucrose and sawdust make to the net immobilization of inorganic soil N and assimilation of both C and N into microbial biomass when they are used as part of a restoration plan to promote the establishment of indigenous vegetation on abandoned agricultural fields on the Central Hungarian Plain. Both amendments led to net N immobilization. Sucrose addition also led to mobilization of N from the soil organic N pool and its immobilization into microbial biomass, whereas sawdust addition apparently immobilized soil N into a non-biomass compartment or a biomass component that was not detected by the conventional biomass N assay (CHCl3 fumigation and extraction). This suggests that the N was either cycled through the biomass, but not immobilized within it, or that it was immobilized in a protected biomass fraction different to the fraction into which N was immobilized in response to sucrose addition.