DESIGN OF A MINIATURIZED SOP INTEGRATED GNSS RF FRONT-END MODULE

Navigation devices used to be bulky and expensive and were not widely commercialized for personal use. Nowadays, all useful electronic devices are turning into being handheld so that they can be conveniently used anytime and anywhere. One can claim that almost any mobile phone, used today, has quite strong navigational capabilities that can efficiently work anywhere in the globe. No matter where you are, you can easily know your exact location and make your way smoothly to wherever you would like to go. This couldn’t have been made possible without the existence of efficient and small microwave circuits responsible for the transmission and reception of high quality navigation signals. This thesis is mainly concerned with the design of novel highly miniaturized and efficient filtering components working in the Global Navigational Satellite Systems (GNSS) frequency band to be integrated within an efficient Radio Frequency (RF) front-end module (FEM). A System-on-Package (SoP) integration technique is adopted for the design of all the components in this thesis. Two novel miniaturized filters are designed, where one of them is a wideband filter targeting the complete GNSS band with a fractional bandwidth of almost 50% at a center frequency of 1.385 GHz. This filter utilizes a direct inductive coupling topology to achieve the required wide band performance. It also has very good out-of-band rejection and low IL. Whereas the other dual band filter will only cover the lower and upper GNSS bands with a rejection notch in between the two bands. It has very good inter band rejection. The well-known “divide and conquer” design methodology was applied for the design of this filter to help save valuable design and optimization time. Moreover, the performance of two commercially available ultra-Low Noise Amplifiers (LNAs) is studied. The complete RF FEM showed promising preliminary performance in terms of noise figure, gain and bandwidth, where it out performed other commercial front-ends in these three aspects. All the designed circuits are fabricated and tested. The measured results are found to be in good agreements with the simulations.

Using front-end and formative evaluation to design and test persuasive bird feeding warning signs

Wildlife feeding is a wide-spread and controversial practice that can pose serious threats to the safety of both wildlife and visitors. The design and effectiveness of warning signs in recreational areas varies considerably and is rarely the product of theoretical models or scientific research. This study uses front-end and formative evaluation to design and test the perceived effectiveness of warning signs relating to bird feeding. Stage One examined visitors' beliefs, attitudes and bird feeding behaviour and found significant differences between feeders and non-feeders. Stage Two involved designing and evaluating three signs that built on the beliefs, knowledge and mis/conceptions identified in Stage One. Respondents thought the sign that focused on the birds' health and safety would be the most persuasive, however, elements of the other two signs were also positively evaluated. The article concludes with recommendations for the wording of future bird feeding warning signs. (c) 2004 Elsevier Ltd. All rights reserved.

The development of a new compiler-compiler front-end

The increasing cost of developing complex software systems has created a need for tools which aid software construction. One area in which significant progress has been made is with the so-called Compiler Writing Tools (CWTs); these aim at automated generation of various components of a compiler and hence at expediting the construction of complete programming language translators. A number of CWTs are already in quite general use, but investigation reveals significant drawbacks with current CWTs, such as lex and yacc. The effective use of a CWT typically requires a detailed technical understanding of its operation and involves tedious and error-prone input preparation. Moreover, CWTs such as lex and yacc address only a limited aspect of the compilation process; for example, actions necessary to perform lexical symbol valuation and abstract syntax tree construction must be explicitly coded by the user. This thesis presents a new CWT called CORGI (COmpiler-compiler from Reference Grammar Input) which deals with the entire `front-end' component of a compiler; this includes the provision of necessary data structures and routines to manipulate them, both generated from a single input specification. Compared with earlier CWTs, CORGI has a higher-level and hence more convenient user interface, operating on a specification derived directly from a `reference manual' grammar for the source language. Rather than developing a compiler-compiler from first principles, CORGI has been implemented by building a further shell around two existing compiler construction tools, namely lex and yacc. CORGI has been demonstrated to perform efficiently in realistic tests, both in terms of speed and the effectiveness of its user interface and error-recovery mechanisms.

The implementation of a functional query language front-end to a relational database system. Available in 2 volumes.

Database systems have a user interface one of the components of which will normally be a query language which is based on a particular data model. Typically data models provide primitives to define, manipulate and query databases. Often these primitives are designed to form self-contained query languages. This thesis describes a prototype implementation of a system which allows users to specify queries against the database in a query language whose primitives are not those provided by the actual model on which the database system is based, but those provided by a different data model. The implementation chosen is the Functional Query Language Front End (FQLFE). This uses the Daplex functional data model and query language. Using FQLFE, users can specify the underlying database (based on the relational model) in terms of Daplex. Queries against this specified view can then be made in Daplex. FQLFE transforms these queries into the query language (Quel) of the underlying target database system (Ingres). The automation of part of the Daplex function definition phase is also described and its implementation discussed.

Especificações e concepções de front-end UHF integrado e multipadrão em tecnologia CMOS 130nm

The Brazilian Environmental Data Collecting System (SBCDA) collects and broadcasts meteorological and environmental data, to be handled by dozens of institutions and organizations. The system space segment, composed by the data collecting satellites, plays an important role for the system operation. To ensure the continuity and quality of these services, efforts are being made to the development of new satellite architectures. Aiming a reduction of size and power consumption, the design of an integrated circuit containing a receiver front-end is proposed, to be embedded in the next SBCDA satellite generations. The circuit will also operate under the requirements of the international data collecting standard ARGOS. This work focuses on the design of an UHF low noise amplifier and mixers in a CMOS standard technology. The specifi- cations are firstly described and the circuit topologies presented. Then the circuit conception is discussed and the design variables derived. Finally, the layout is designed and the final results are commented. The chip will be fabricated in a 130 nm technology from ST Microelectronics.

DESIGN OF A MINIATURIZED SOP INTEGRATED GNSS RF FRONT-END MODULE

Navigation devices used to be bulky and expensive and were not widely commercialized for personal use. Nowadays, all useful electronic devices are turning into being handheld so that they can be conveniently used anytime and anywhere. One can claim that almost any mobile phone, used today, has quite strong navigational capabilities that can efficiently work anywhere in the globe. No matter where you are, you can easily know your exact location and make your way smoothly to wherever you would like to go. This couldn’t have been made possible without the existence of efficient and small microwave circuits responsible for the transmission and reception of high quality navigation signals. This thesis is mainly concerned with the design of novel highly miniaturized and efficient filtering components working in the Global Navigational Satellite Systems (GNSS) frequency band to be integrated within an efficient Radio Frequency (RF) front-end module (FEM). A System-on-Package (SoP) integration technique is adopted for the design of all the components in this thesis. Two novel miniaturized filters are designed, where one of them is a wideband filter targeting the complete GNSS band with a fractional bandwidth of almost 50% at a center frequency of 1.385 GHz. This filter utilizes a direct inductive coupling topology to achieve the required wide band performance. It also has very good out-of-band rejection and low IL. Whereas the other dual band filter will only cover the lower and upper GNSS bands with a rejection notch in between the two bands. It has very good inter band rejection. The well-known “divide and conquer” design methodology was applied for the design of this filter to help save valuable design and optimization time. Moreover, the performance of two commercially available ultra-Low Noise Amplifiers (LNAs) is studied. The complete RF FEM showed promising preliminary performance in terms of noise figure, gain and bandwidth, where it out performed other commercial front-ends in these three aspects. All the designed circuits are fabricated and tested. The measured results are found to be in good agreements with the simulations.

Análisis y simulación de un rectificador trifásico controlado Active Front End (AFE)

Este artículo presenta un resultado de investigación financiado con recursos propios en el que se expone un modelo en espacio de estados de un rectificador trifásico controlado active front end. Utilizando este modelo se deriva una ley de control orientado al voltaje (VOC), enfocado en el comportamiento como carga resistiva, factor de potencia unitario, el cual es probado mediante simulación usando el Toolbox SimPowerSystem en Simulink de Matlab®.

Front end development for building automation systems using JavaScript Frameworks

Automation technologies are widely acclaimed to have the potential to significantly reduce energy consumption and energy-related costs in buildings. However, despite the abundance of commercially available technologies, automation in domestic environments keep on meeting commercial failures. The main reason for this is the development process that is used to build the automation applications, which tend to focus more on technical aspects rather than on the needs and limitations of the users. An instance of this problem is the complex and poorly designed home automation front-ends that deter customers from investing in a home automation product. On the other hand, developing a usable and interactive interface is a complicated task for developers due to the multidisciplinary challenges that need to be identified and solved. In this context, the current research work investigates the different design problems associated with developing a home automation interface as well as the existing design solutions that are applied to these problems. The Qualitative Data Analysis approach was used for collecting data from research papers and the open coding process was used to cluster the findings. From the analysis of the data collected, requirements for designing the interface were derived. A home energy management functionality for a Web-based home automation front-end was developed as a proof-of-concept and a user evaluation was used to assess the usability of the interface. The results of the evaluation showed that this holistic approach to designing interfaces improved its usability which increases the chances of its commercial success.

Sviluppo del back-end per una App mobile con lo scopo di abbattere i costi delle chiamate telefoniche internazionali

Questa tesi tratta dello sviluppo di un progetto, svolto durante il periodo di tirocinio presso SMS.it, azienda specializzata nel settore della telefonia con sede a Bologna. L'azienda in questione ha commissionato, al sottoscritto ed al mio collega Daniele Sciuto, l'implementazione di un'applicazione cross-platform per smartphone, ed il relativo server. L'azienda ci ha fornito le specifiche del progetto, e ci ha seguiti in tutte le fasi del suo sviluppo. L'applicazione è pensata per offrire agli utenti la possibilità di usufruire di tariffe telefoniche agevolate. I vantaggi sono maggiormente apprezzabili nelle chiamate internazionali. Queste tariffe sono possibili grazie agli accordi fra l'azienda e vari operatori di telefonia. Nella primo capitolo di questo elaborato, viene analizzato cosa ci è stato richiesto di realizzare, le specifiche del progetto dateci dall'azienda e quali sono i vincoli ai quali ci si è dovuti attenere. Nella secondo capitolo, viene descritto nel dettaglio la progettazione delle singole funzionalità dell'applicazione, e i rapporti che ci sono fra il front-end ed il back-end. Successivamente, sono analizzate le tecnologie necessarie per la realizzazione e il loro utilizzo nell'applicazione. Come richiestoci dall'azienda, alcuni dettagli implementativi sono stati omessi, per garantire il rispetto del segreto industriale. Nonostante ciò viene comunque fornita una panoramica completa di ciò che è stato realizzato. In ultima analisi è descritta qualitativamente l'applicazione ottenuta, e come aderisca alle specifiche richieste.

Pulse-front tilt for short-wavelength lasing by means of traveling-wave plasma-excitation

Generation of coherent short-wavelength radiation across a plasma column is dramatically improved under traveling-wave excitation (TWE). The latter is optimized when its propagation is close to the speed of light, which implies small-angle target-irradiation. Yet, short-wavelength lasing needs large irradiation angles in order to increase the optical penetration of the pump into the plasma core. Pulse-front back-tilt is considered to overcome such trade-off. In fact, the TWE speed depends on the pulse-front slope (envelope of amplitude), whereas the optical penetration depth depends on the wave-front slope (envelope of phase). Pulse-front tilt by means of compressor misalignment was found effective only if coupled with a high-magnification front-end imaging/focusing component. It is concluded that speed matching should be accomplished with minimal compressor misalignment and maximal imaging magnification.

End-User Development Success Factors and their Application to Composite Web Development Environments

The Future Internet is expected to be composed of a mesh of interoperable Web services accessed from all over the Web. This approach has not yet caught on since global user-service interaction is still an open issue. Successful composite applications rely on heavyweight service orchestration technologies that raise the bar far above end-user skills. The weakness lies in the abstraction of the underlying service front-end architecture rather than the infrastructure technologies themselves. In our opinion, the best approach is to offer end-to-end composition from user interface to service invocation, as well as an understandable abstraction of both building blocks and a visual composition technique. In this paper we formalize our vision with regard to the next-generation front-end Web technology that will enable integrated access to services, contents and things in the Future Internet. We present a novel reference architecture designed to empower non-technical end users to create and share their own self-service composite applications. A tool implementing this architecture has been developed as part of the European FP7 FAST Project and EzWeb Project, allowing us to validate the rationale behind our approach.

An evaluation of occupant protection in frontal interior impact for unrestrained front seat occupants of cars and light trucks. Technical report.

Mode of access: Internet.

Characterising creativity : a holistic methodology for the assessment of creative works

This paper reports on the early stages of a design experiment in educational assessment that challenges the dichotomous legacy evident in many assessment activities. Combining social networking technologies with the sociology of education the paper proposes that assessment activities are best understood as a negotiable field of exchange. In this design experiment students, peers and experts engage in explicit, "front-end" assessment (Wyatt-Smith, 2008) to translate holistic judgments into institutional, and potentiality economic capital without adhering to long lists of pre-set criteria. This approach invites participants to use social networking technologies to judge creative works using scatter graphs, keywords and tag clouds. In doing so assessors will refine their evaluative expertise and negotiate the characteristics of creative works from which criteria will emerge (Sadler, 2008). The real-time advantages of web-based technologies will aggregate, externalise and democratise this transparent method of assessment for most, if not all, creative works that can be represented in a digital format.

Creativity, design and entrepreneurship : management education and development for innovation

Creativity, design and entrepreneurship, have been recognized as important contributors to a firm’s innovation and to the nation’s economic growth. Creativity and design play important roles in the fuzzy front end of a firm’s innovation process and also in corporate venturing processes, but the relationship between creativity, design and entrepreneurship to a large extent has not explicitly been examined. This exploratory conceptual paper briefly reviews the separate bodies of research on creativity, design and entrepreneurship, identifying similarities and differences in constructs and applications and identifying implications for business and for management education.