Yb3+-doped 200 mu m diameter core, gain guided index-antiguided fiber

The lasing in an end-pumped gain guided index-antiguided (GG-IAG) Yb3+-doped silicate glass fiber with a 200 mu m diameter core is demonstrated. Laser beams with similar beam propagation factors M (2) and mode field diameters W (0) (> 160 mu m) were observed at the output end of the GG-IAG fibers under different pump powers, which indicated that single mode behavior and excellent beam quality were achieved during propagation. Furthermore, the laser amplifier characteristics in the present Yb3+-doped GG-IAG fiber were also evaluated.

Generation of 10 GHz, 1.9 ps optical pulse train using semiconductor optical amplifier and silica-based highly nonlinear fiber

We propose a simple approach to generate a high quality 10 GHz 1.9 ps optical pulse train using a semiconductor optical amplifier and silica-based highly nonlinear fiber. An optical pulse generator based on our proposed scheme is easy to set up with commercially available optical components. A 10 GHz, 1.9 ps optical pulse train is obtained with timing jitter as low as 60 fs over the frequency range 10 Hz-1 MHz. With a wavelength tunable CW laser, a wide wavelength tunable span can be achieved over the entire C band. The proposed optical pulse generator also can operate at different repetition rates from 3 to 10 GHz.

Synthesis of NaA zeolite membrane on a ceramic hollow fiber

NaA zeolite membrane was successfully synthesized on a ceramic hollow fiber with an outer diameter of 400 mum, a thickness of 100 mum and an average pore radius of 0.1 mum. The as-synthesized membranes were characterized by XRD, SEM as well as gas permeation. A continuous C NaA zeolite membrane formed after a three-stage synthesis. The membrane thickness was similar to5 mum. Gas permeation data indicated that a relatively high quality NaA zeolite membrane formed on the ceramic hollow fiber support. (C) 2003 Elsevier B.V. All rights reserved.

Quality analysis of herbal medicine products prepared from Herba sarcandrae by capillary electrophoresis with electrochemical detection

A capillary electrophoresis with electrochemical detection(CE-ED) method was developed for the quality analysis of herbal medicine products prepared from the same herb of Herba Sarcandrae: Fufang Caoshanhu tablets, Qingrexiaoyanning capsules, and Xuekang oral liquids. Under the optimal analysis conditions, the low detection limit[1.0x10(-7) mol/L(S/N=3)] and the wide linear range(1.0x10(-7)-1.0x10(-4) mol/L) were obtained for quality standard compound of isofraxidin. The precisions of the peak current and the migration time(as RSDs) for the real sample analysis were 2.0%-2.6%, and 1.2%-1.8% for isofraxidin, respectively.

Analysis of nephroloxic and carcinogenic aristolochic acids in Aristolochia plants by capillary electrophoresis with electrochemical detection at a carbon fiber microdisk electrode

Aristolochic acids (AAs) are the main bioactive ingredients in the most of Aristolochia plants, which are used to make dietary supplements, slimming pills and Traditional Chinese Medicines (TCMs). Excessive ingestion of AAs can lead to serious nephropathy. Therefore, quantitative analysis and quality control for the plants containing AAs is of great importance. In this paper, capillary electrophoresis (CE) with electrochemical detection (ED) at a 33 mu m carbon fiber microdisk electrode (CFE) has been applied to detect AA-I and AA-II in Aristolochia plants. Under the optimum conditions: detection potential at 1.20 V, 2.0 x 10(-2) mol L-1 phosphate buffer solution (PBS) (pH 10.0), injection time 25 s at a height of 17 cm and separation voltage at 12.5 kV, the AA-I and AA-II were baseline separated within 5 min. Low detection limits for AA-I and AA-II were 4.0 x 10(-8) mol L-1 and 1.0 x 10(-7) mol L-1, respectively. Wide linear ranges were from 4.0 x 10(-8) mol L-1 to 1.9 x 10(-5) mol L-1 and 1.0 X 10(-7) mol L-1 to 5.0 x 10(-5) mol L-1 for AA-I and AA-II, respectively. The proposed method has been successfully applied to analyze AAs contents in plant extracts. The results indicated that the contents of AAs in each part of Aristolochia debilis Sieb. Et Zucc.

Numerical investigation of the effects of drill geometry on drilling induced delamination of carbon fiber reinforced composites

Drilling is a major process in the manufacturing of holes required for the assemblies of composite laminates in aerospace industry. Simulation of drilling process is an effective method in optimizing the drill geometry and process parameters in order to improve hole quality and to reduce the drill wear. In this research we have developed three-dimensional (3D) FE model for drilling CFRP. A 3D progressive intra-laminar failure model based on the Hashin's theory is considered. Also an inter-laminar delamination model which includes the onset and growth of delamination by using cohesive contact zone is developed. The developed model with inclusion of the improved delamination model and real drill geometry is used to make comparison between the step drill of different stage ratio and twist drill. Thrust force, torque and work piece stress distributions are estimated to decrease by the use of step drill with high stage ratio. The model indicates that delamination and other workpiece defects could be controlled by selection of suitable step drill geometry. Hence the 3D model could be used as a design tool for drill geometry for minimization of delamination in CFRP drilling. © 2013 Elsevier Ltd.

Comparative study of tool life and hole quality in drilling of CFRP/titanium stack using coated carbide drill

The use of hybrid materials including carbon fiber reinforced plastics (CFRPs) and lightweight metals such as titanium are increasing particularly in aerospace applications. Multi-material stacks require a number of holes for the assembly purposes. In this research, drilling trials have been carried out in CFRP, Ti-6Al-4V and CFRP/Ti-6Al-4V stack workpieces using AlTiN coated tungsten carbide drill bit. The effects of process parameters have been investigated. The thrust force, torque, burr formation, delamination, surface roughness and tool wear have been analyzed at various processing condition. The experimental results have shown that the thrust force, torque, burr formation and the average surface roughness increase with the increased feed rate and decrease with the increased cutting speed in drilling of Ti-6Al-4V. In drilling CFRP, delamination and the average surface roughness has similar tendency with the cutting parameters however thrust force and torque rises with the increased cutting speed. The results showed that after making 15 holes in CFRP/Ti-6Al-4V stack, measured thrust forces were increased by 20% in CFRP and by 45% in Ti-6Al-4V. Delamination was found to be much smaller in drilling of CFRP in stack from compared to drilling single CFRP. Tool life was significantly shortened in drilling of stack due to the combination of the wear mechanisms.

Dietary patterns associated with diet quality among First Nations women living on reserves in British Columbia

Les Indigènes canadiens vivent une rapide transition nutritionnelle marquée par une consommation accrue des produits commercialisés au dépit des aliments traditionnels. Ce mémoire cherche à identifier les patrons alimentaires associés à une meilleure alimentation des femmes autochtones vivant dans les réserves en Colombie Britannique. L’échantillon (n=493) a été sélectionné de l’étude ‘First Nations Food, Nutrition, and Environment Study’. L’étude a utilisé des rappels alimentaires de 24 heures. Pour identifier les patrons alimentaires, un indice de qualité alimentaire (QA) basé sur 10 éléments nutritionnels (fibre alimentaire, gras totaux/saturés, folate, magnésium, calcium, fer, vitamines A, C, D) a permis de classifier les sujets en trois groupes (tertiles). Ces groupes ont été comparés sur leur consommation de 25 groupes alimentaires (GAs) en employant des tests statistiques non-paramétriques (Kruskal-Wallis et ANCOVA). Une analyse discriminante (AD) a confirmé les GAs associés à la QA. La QA des sujets était globalement faible car aucun rappel n’a rencontré les consommations recommandées pour tous les 10 éléments nutritionnels. L'AD a confirmé que les GAs associés de façon significative à la QA étaient ‘légumes et produits végétaux’, ‘fruits’, ‘aliments traditionnels’, ‘produits laitiers faibles en gras’, ‘soupes et bouillons’, et ‘autres viandes commercialisées’ (coefficients standardisés= 0,324; 0,295; 0,292; 0,282; 0,157; -0.189 respectivement). Le pourcentage de classifications correctes était 83.8%. Nos résultats appuient la promotion des choix alimentaires recommandés par le « Guide Alimentaire Canadien- Premières Nations, Inuits, et Métis ». Une consommation accrue de légumes, fruits, produits laitiers faibles en gras, et aliments traditionnels caractérise les meilleurs patrons alimentaires.

Development of optical fiber sensors for selected chemical and physical sensing applications

The objective of the preset work is to develop optical fiber sensors for various physical and chemical parameters. As a part of this we initially investigated trace analysis of silica, ammonia, iron and phosphate in water. For this purpose the author has implemented a dual wavelength probing scheme which has many advantages over conventional evanescent wave sensors. Dual wavelength probing makes the design more reliable and repeatable and this design makes the sensor employable for concentration, chemical content, adulteration level, monitoring and control in industries or any such needy environments. Use of low cost components makes the system cost effective and simple. The Dual wavelength probing scheme is employed for the trace analysis of silica, iron, phosphate, and ammonia in water. Such sensors can be employed for the steam and water quality analysers in power plants. Few samples from a power plant are collected and checked the performance of developed system for practical applications.

Accumulation of nutrients in sweet peppers cultivated in coconut fiber

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Growth analysis of sweet pepper cultivated in coconut fiber in a greenhouse

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of Mahanarva fimbriolata (Stål) (Hemiptera: Cercopidae) injury on the quality of cane juice

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Qualitative-feed-restricted heavy swine: meat quality and morpho-histochemical characteristics of muscle fibers

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Carcass characteristics and meat quality of heavy swine fed different citrus pulp levels

Foi realizado um ensaio utilizando 36 suínos machos castrados, com peso inicial de 83,7±5,1kg, para avaliar o efeito da inclusão de polpa cítrica, 0, 10, 20 e 30%, em um programa de restrição alimentar qualitativa para suínos abatidos aos 130kg de peso, sobre o peso dos órgãos do sistema digestório e sobre características da carcaça e da qualidade da carne. A inclusão de polpa cítrica proporcionou aumento linear (P<0,05) nos pesos do estômago, cólon e fígado, e efeito quadrático (P<0,05) no peso do ceco. Foi observada redução linear (P<0,05) no peso, no rendimento da carcaça e no peso do pernil, porém não houve efeito (P>0,05) sobre o rendimento do pernil. Maior inclusão de polpa cítrica não foi suficiente para reduzir a espessura do toucinho e aumentar a quantidade de carne magra na carcaça, mostrando que a restrição alimentar qualitativa não foi eficiente. Foi observado aumento linear (P<0,05) do pH da carcaça resfriada e linear negativo (P<0,05) sobre as variáveis indicativas de cor da carne em função da inclusão da polpa cítrica nas dietas. A adição de polpa cítrica em programas de restrição alimentar qualitativa não foi eficiente. Por não promover nenhum efeito deletério sobre as características da carne, a polpa cítrica pode ser utilizada como ingrediente alternativo para suínos em terminação.

Fractography analysis and fatigue strength of carbon fiber/RTM6 laminates

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)