Evaluation of drilling process in Ti6Al4V using 3D FE simulation

Drilling of Ti6Al4V is investigated experimentally and numerically. A 3D finite element model developed based on Lagrangian approach using commercial finite element software ABAQUS/explicit. 3D complex drill geometry is included in the model. The drilling process simulations are performed at the combinations of three cutting speed and four feed rates. The effects of cutting parameters on the induced thrust force and torque are predicted by the developed model. For validation purpose, experimental trials have been performed in similar condition to the simulations. The forces and torques measured during experiment are compared to the results of the finite element analysis. The agreement of the experimental results for force and torque values with the FE results is very good. Moreover, surface roughness of the holes was measured for mapping of machining. Copyright © 2013 Inderscience Enterprises Ltd.

Evaluation of thermochemical biomass conversion in fluidized bed

Dado o aumento acelerado dos preços dos combustíveis fósseis e as incertezas quanto à sua disponibilidade futura, tem surgido um novo interesse nas tecnologias da biomassa aplicadas à produção de calor, eletricidade ou combustíveis sintéticos. Não obstante, para a conversão termoquímica de uma partícula de biomassa sólida concorrem fenómenos bastante complexos que levam, em primeiro lugar, à secagem do combustível, depois à pirólise e finalmente à combustão ou gasificação propriamente ditas. Uma descrição relativamente incompleta de alguns desses estágios de conversão constitui ainda um obstáculo ao desenvolvimento das tecnologias que importa ultrapassar. Em particular, a presença de elevados conteúdos de matéria volátil na biomassa põe em evidência o interesse prático do estudo da pirólise. A importância da pirólise durante a combustão de biomassa foi evidenciada neste trabalho através de ensaios realizados num reator piloto de leito fluidizado borbulhante. Verificou-se que o processo ocorre em grande parte à superfície do leito com chamas de difusão devido à libertação de voláteis, o que dificulta o controlo da temperatura do reator acima do leito. No caso da gasificação de biomassa a pirólise pode inclusivamente determinar a eficiência química do processo. Isso foi mostrado neste trabalho durante ensaios de gasificação num reator de leito fluidizado de 2MWth, onde um novo método de medição permitiu fechar o balanço de massa ao gasificador e monitorizar o grau de conversão da biomassa. A partir destes resultados tornou-se clara a necessidade de descrever adequadamente a pirólise de biomassa com vista ao projeto e controlo dos processos. Em aplicações de engenharia há particular interesse na estequiometria e propriedades dos principais produtos pirolíticos. Neste trabalho procurou-se responder a esta necessidade, inicialmente através da estruturação de dados bibliográficos sobre rendimentos de carbonizado, líquidos pirolíticos e gases, assim como composições elementares e poderes caloríficos. O resultado traduziu-se num conjunto de parâmetros empíricos de interesse prático que permitiram elucidar o comportamento geral da pirólise de biomassa numa gama ampla de condições operatórias. Para além disso, propôs-se um modelo empírico para a composição dos voláteis que pode ser integrado em modelos compreensivos de reatores desde que os parâmetros usados sejam adequados ao combustível ensaiado. Esta abordagem despoletou um conjunto de ensaios de pirólise com várias biomassas, lenhina e celulose, e temperaturas entre os 600 e 975ºC. Elevadas taxas de aquecimento do combustível foram alcançadas em reatores laboratoriais de leito fluidizado borbulhante e leito fixo, ao passo que um sistema termo-gravimétrico permitiu estudar o efeito de taxas de aquecimento mais baixas. Os resultados mostram que, em condições típicas de processos de combustão e gasificação, a quantidade de voláteis libertada da biomassa é pouco influenciada pela temperatura do reator mas varia bastante entre combustíveis. Uma análise mais aprofundada deste assunto permitiu mostrar que o rendimento de carbonizado está intimamente relacionado com o rácio O/C do combustível original, sendo proposto um modelo simples para descrever esta relação. Embora a quantidade total de voláteis libertada seja estabelecida pela composição da biomassa, a respetiva composição química depende bastante da temperatura do reator. Rendimentos de espécies condensáveis (água e espécies orgânicas), CO2 e hidrocarbonetos leves descrevem um máximo relativamente à temperatura para dar lugar a CO e H2 às temperaturas mais altas. Não obstante, em certas gamas de temperatura, os rendimentos de algumas das principais espécies gasosas (e.g. CO, H2, CH4) estão bem correlacionados entre si, o que permitiu desenvolver modelos empíricos que minimizam o efeito das condições operatórias e, ao mesmo tempo, realçam o efeito do combustível na composição do gás. Em suma, os ensaios de pirólise realizados neste trabalho permitiram constatar que a estequiometria da pirólise de biomassa se relaciona de várias formas com a composição elementar do combustível original o que levanta várias possibilidades para a avaliação e projeto de processos de combustão e gasificação de biomassa.

Drilling tool geometry evaluation for reinforced composite laminates

In this work, a comparative study on different drill point geometries and feed rate for composite laminates drilling is presented. For this goal, thrust force monitoring during drilling, hole wall roughness measurement and delamination extension assessment after drilling is accomplished. Delamination is evaluated using enhanced radiography combined with a dedicated computational platform that integrates algorithms of image processing and analysis. An experimental procedure was planned and consequences were evaluated. Results show that a cautious combination of the factors involved, like drill tip geometry or feed rate, can promote the reduction of delamination damage.

Delamination analysis of carbon fibre reinforced laminates: evaluation of a special step drill

Drilling of carbon fibre/epoxy laminates is usually carried out using standard drills. However, it is necessary to adapt the processes and/or tooling as the risk of delamination, or other damages, is high. These problems can affect mechanical properties of produced parts, therefore, lower reliability. In this paper, four different drills – three commercial and a special step (prototype) – are compared in terms of thrust force during drilling and delamination. In order to evaluate damage, enhanced radiography is applied. The resulting images were then computational processed using a previously developed image processing and analysis platform. Results show that the prototype drill had encouraging results in terms of maximum thrust force and delamination reduction. Furthermore, it is possible to state that a correct choice of drill geometry, particularly the use of a pilot hole, a conservative cutting speed – 53 m/min – and a low feed rate – 0.025 mm/rev – can help to prevent delamination.

Modéliser le processus d’appropriation du feed-back en évaluation du potentiel pour en optimiser les retombées positives auprès des candidats

L’appropriation du feed-back a fait l’objet de plusieurs modèles théoriques en contexte d’évaluation de la performance, notamment par Ilgen, Fisher et Taylor (1979) qui suggèrent un modèle explicitant comment un feed-back en vient à susciter des changements comportementaux. Ce modèle a été repris dans divers domaines de recherche, sans pour autant être adapté en fonction du contexte spécifique dans lequel le feed-back était transmis. Cette thèse propose un modèle d’appropriation du feed-back inspiré des travaux d’Ilgen et al. (1979), mais reflétant les spécificités de l’évaluation du potentiel. Le modèle comporte trois étapes qui sont l’appropriation cognitive (composée de l’acceptation et de la conscientisation), l’intention d’agir dans le sens du feed-back et l’appropriation comportementale. La présente thèse se décompose en trois articles poursuivant les objectifs suivants : (1) Proposer un modèle théorique de l’appropriation du feed-back adapté au contexte de l’évaluation du potentiel. (2) Valider une mesure de l’appropriation cognitive combinant l’acceptation et la conscientisation. (3) Tester empiriquement le modèle d’appropriation du feed-back en contexte d’évaluation du potentiel. Le premier article vise d’abord à circonscrire les fondements de l’évaluation du potentiel et à définir l’appropriation du feed-back. Sur la base de ces informations, le modèle d’Ilgen et al. (1979) est ensuite revu et modifié. Les liens entre les différentes étapes du modèle sont subséquemment étayés par des théories et des études empiriques. L’article se conclue par une réflexion sur les retombées théoriques et pratiques du modèle revisité. L’objectif du second article consiste à développer et valider une mesure de l’appropriation cognitive incluant deux dimensions, à savoir l’acceptation et la conscientisation. Pour ce faire, deux études ont été menées auprès de candidats ayant reçu un feed-back suite à une évaluation du potentiel. Des analyses factorielles exploratoires (N = 111), puis des analyses factorielles confirmatoires (N = 178) ont été réalisées en ce sens. Chaque dimension de l’appropriation cognitive a également été mise en relation avec des variables critères afin de recueillir des éléments de preuve appuyant la validité de l’instrument. La majorité des indices obtenus confirment la présence des deux dimensions pressenties et des constats sont tirés sur la base de ces résultats. Le troisième article vise à vérifier empiriquement les liens anticipés entre les composantes du modèle d’appropriation du feed-back détaillé dans le premier article. Les deux premières étapes du modèle, soit l’appropriation cognitive et l’intention d’agir, ont été mesurées via un questionnaire complété immédiatement après le feed-back par 178 candidats. Ces derniers ont été sollicités trois mois plus tard afin de compléter un second questionnaire portant sur la dernière étape, l’appropriation comportementale, et 97 d’entre eux y ont répondu. Les résultats d’analyses par équations structurelles supportent le modèle et une discussion sur la portée de tels résultats s’en suit.

Deoxynivalenol (DON) naturally contaminated feed impairs the immune response induced by porcine reproductive and respiratory syndrome virus (PRRSV) live attenuated vaccine

Cereal commodities are frequently contaminated with mycotoxins produced by the secondary metabolism of fungal infection. Among these contaminants, deoxynivalenol (DON), also known as vomitoxin, is the most prevalent type B trichothecene mycotoxin worldwide. Pigs are very sensitive to the toxic effects of DON and are frequently exposed to naturally contaminated feed. Recently, DON naturally contaminated feed has been shown to decrease porcine reproductive and respiratory syndrome virus (PRRSV) specific antibody responses following experimental infection. The objective of this study was to determine the impact of DON naturally contaminated feed on the immune response generated following vaccination with PRRSV live attenuated vaccine. Eighteen pigs were randomly divided into three experimental groups of 6 animals based on DON content of the diets (0, 2.5 and 3.5 mg DON/kg). They were fed these rations one week prior to the vaccination and for all the duration of the immune response evaluation. All pigs were vaccinated intra-muscularly with one dose of Ingelvac® PRRSV modified live vaccine (MLV). Blood samples were collected at day −1, 6, 13, 20, 27 and 35 post vaccination (pv) and tested for PRRSV RNA by RT-qPCR and for virus specific antibodies by ELISA. Results showed that ingestion of DON-contaminated diets significantly decreased PRRSV viremia. All pigs fed control diet were viremic while only 1 (17%) and 3 (50%) out of 6 pigs were viremic in the groups receiving 3.5 and 2.5 mg of DON/kg, respectively. Subsequently, all pigs fed control diet developed PRRSV specific antibodies while only viremic pigs that were fed contaminated diets have developed PRRSV specific antibodies. These results suggest that feeding pigs with DON-contaminated diet could inhibit vaccination efficiency of PRRSV MLV by severely impairing viral replication.

Evaluation of cyanobacteria for biomass production and effluent treatment

The microalgae gained importance as food and feed as well as source of fine chemicals since the l960’s. Spirulina became the trend setter due to its easily culturable properties as well as nutritional composition. A rapid expansion of microalgal industry occurred in the Asia-Pacific region as microalgae came to stay as a health food supplement. Microalgae have been an integral component of oxidation ponds usually incorporated with wastewater treatment. Over the last few decades, efforts have been made to apply intensive microalgal cultures to perform biological tertiary treatment of secondary effluents. Given the limited number of species still available for commercial exploitation, it is imperative to isolate and cultivate those photosynthetic organisms with high growth rate and biomass accumulation, which could play the dual role of cleaning the wastewater and also providing useful biomass. This has been the objective of this study ie. 0 To develop pure cultures of local isolates of Cyanobacteria for extraction of biochemicals of commercial value 0 To couple biomass production with effluent treatment

Studies on the evaluation of different sources of proteins, carbohydrates and mineral requirements for juvenile penaeid prawn Penaeus Indicus H. Milne Edwards

In India, directed research on penaeid prawn nutrition was taken up only recently when the aquaculture of prawns gained momentum. One of the important penaeid prawns sought for culture and has great potential is Penagus indiggs, H.Milne Edwards. The Central Marine Fisheries Research Institute working on different aspects of culture of this species over the past one and half decades, has developed a hatchery technology for mass production of its seed and has suggested several improvements on its farming in the grow-out systems. One of the areas of active research in this direction has been on the nutrition of the species with a view to develop suitable feed not only for hatchery production of seed, but also in the field culture. As part of this investigation, the present study, on the evaluation of different protein and carbohydrate sources and mineral requirements for the juvenile E, indicus was taken up and the results obtained are embodied in the thesis

In vivo screening of mangrove plants for anti WSSV activity in Penaeus monodon, and evaluation of Ceriops tagal as a potential source of antiviral molecules

The objective of the study was to find out a natural way to fight white spot syndrome virus (WSSV) in cultured shrimps, as the present scenario necessitated an organic remedy for the devastating pathogen in crustaceans. Under this research programme seven mangrove plants were collected, identified and aqueous extracts screened for their protective effect on the giant tiger shrimp Penaeus monodon against WSSV. The experimental design consisted two modes of application, such as exposure of the virus to the extract and injection challenge, and oral administration of the extract coated feed followed by oral challenge. All experimental animals were monitored through a nested diagnostic PCR analysis. Of the seven mangrove extracts screened aqueous extract from Ceriops tagal imparted total protection to shrimp from WSSV when challenged by both methods. Shrimps administered with the aqueous extract from C. tagal were devoid of virions. The HPLC fingerprint of the aqueous extracts from C. tagal showed more than 25 peaks and 7 of them were larger and well separated. Preliminary phytochemical analysis revealed the presence of alkaloids, flavonoids, polyphenolics, cardiac glycosides, saponins and sterols. The study indicated suitability of the aqueous extract of C. tagal as a possible prophylaxis for WSSV infection in shrimp. This is the first report on the anti WSSV property of the mangrove plant C. tagal

In vivo screening of mangrove plants for anti WSSV activity in Penaeus monodon, and evaluation of Ceriops tagal as a potential source of antiviral molecules

The objective of the study was to find out a natural way to fight white spot syndrome virus (WSSV) in cultured shrimps, as the present scenario necessitated an organic remedy for the devastating pathogen in crustaceans. Under this research programme seven mangrove plants were collected, identified and aqueous extracts screened for their protective effect on the giant tiger shrimp Penaeus monodon against WSSV. The experimental design consisted two modes of application, such as exposure of the virus to the extract and injection challenge, and oral administration of the extract coated feed followed by oral challenge. All experimental animals were monitored through a nested diagnostic PCR analysis. Of the seven mangrove extracts screened aqueous extract from Ceriops tagal imparted total protection to shrimp from WSSV when challenged by both methods. Shrimps administered with the aqueous extract from C. tagal were devoid of virions. The HPLC fingerprint of the aqueous extracts from C. tagal showed more than 25 peaks and 7 of them were larger and well separated. Preliminary phytochemical analysis revealed the presence of alkaloids, flavonoids, polyphenolics, cardiac glycosides, saponins and sterols. The study indicated suitability of the aqueous extract of C. tagal as a possible prophylaxis for WSSV infection in shrimp. This is the first report on the anti WSSV property of the mangrove plant C. tagal

Evaluation of two hybrid metric-conceptual models, for simulating phosphorus transfer from agricultural land in the river enborne, a lowland UK catchment

Across Europe, elevated phosphorus (P) concentrations in lowland rivers have made them particularly susceptible to eutrophication. This is compounded in southern and central UK by increasing pressures on water resources, which may be further enhanced by the potential effects of climate change. The EU Water Framework Directive requires an integrated approach to water resources management at the catchment scale and highlights the need for modelling tools that can distinguish relative contributions from multiple nutrient sources and are consistent with the information content of the available data. Two such models are introduced and evaluated within a stochastic framework using daily flow and total phosphorus concentrations recorded in a clay catchment typical of many areas of the lowland UK. Both models disaggregate empirical annual load estimates, derived from land use data, as a function of surface/near surface runoff, generated using a simple conceptual rainfall-runoff model. Estimates of the daily load from agricultural land, together with those from baseflow and point sources, feed into an in-stream routing algorithm. The first model assumes constant concentrations in runoff via surface/near surface pathways and incorporates an additional P store in the river-bed sediments, depleted above a critical discharge, to explicitly simulate resuspension. The second model, which is simpler, simulates P concentrations as a function of surface/near surface runoff, thus emphasising the influence of non-point source loads during flow peaks and mixing of baseflow and point sources during low flows. The temporal consistency of parameter estimates and thus the suitability of each approach is assessed dynamically following a new approach based on Monte-Carlo analysis. (c) 2004 Elsevier B.V. All rights reserved.

A safety evaluation of genetically modified feedstuffs for livestock production; the fate of transgenic DNA and proteins

dTwo genetic constructs used to confer improved agronomic characteristics, namely herbicide tolerance (HT) in maize and soyabean and insect resistance (Bt) in maize, are considered in respect of feeding to farm livestock, animal performance and the nutritional value and safety of animal products. A review of nucleic acid (DNA) and protein digestion in farm livestock concludes that the frequency of intact transgenic DNA and proteins of GM and non-GM crops being absorbed is minimal/non existent, although there is some evidence of the presence of short fragments of rubisco DNA of non-GM soya in animal tissues. It has been established that feed processing (especially heat) prior to feeding causes significant disruption of plant DNA. Studies with ruminant and non-ruminant farm livestock offered GM feeds demonstrated that animal performance and product composition are unaffected and that there is no evidence of transgenic DNA or proteins of current GM in the products of animals consuming such feeds. On this evidence, current HT and Bt constructs represent no threat to the health of animals, or humans consuming the products of such animals. However as new GM constructs become available it will be necessary to subject these to rigorous evaluation.

In vitro evaluation of fibrolytic enzymes as additives for maize (Zea mays L.) silage - I. Effects of ensiling temperature, enzyme source and addition level

A series of experiments was completed to investigate the impact of addition of enzymes at ensiling on in vitro rumen degradation of maize silage. Two commercial products, Depot 40 (D, Biocatalysts Ltd., Pontypridd, UK) and Liquicell 2500 (L, Specialty Enzymes and Biochemicals, Fresno, CA, USA), were used. In experiment 1, the pH optima over a pH range 4.0-6.8 and the stability of D and L under changing pH (4.0, 5.6, 6.8) and temperature (15 and 39 degreesC) conditions were determined. In experiment 2, D and L were applied at three levels to whole crop maize at ensiling, using triplicate 0.5 kg capacity laboratory minisilos. A completely randomized design with a factorial arrangement of treatments was used. One set of treatments was stored at room temperature, whereas another set was stored at 40 degreesC during the first 3 weeks of fermentation, and then stored at room temperature. Silages were opened after 120 days. Results from experiment I indicated that the xylanase activity of both products showed an optimal pH of about 5.6, but the response differed according to the enzyme, whereas the endoglucanase activity was inversely related to pH. Both products retained at least 70% of their xylanase activity after 48 h incubation at 15 or 39 degreesC. In experiment 2, enzymes reduced (P < 0.05) silage pH, regardless of storage temperature and enzyme level. Depol 40 reduced (P < 0.05) the starch contents of the silages, due to its high alpha-amylase activity. This effect was more noticeable in the silages stored at room temperature. Addition of L reduced (P < 0.05) neutral detergent fiber (NDF) and acid detergent fiber (ADF) contents. In vitro rumen degradation, assessed using the Reading Pressure Technique (RPT), showed that L increased (P < 0.05) the initial 6 h gas production (GP) and organic matter degradability (OMD), but did not affect (P > 0.05) the final extent of OMD, indicating that this preparation acted on the rumen degradable material. In contrast, silages treated with D had reduced (P < 0.05) rates of gas production and OMD. These enzymes, regardless of ensiling temperature, can be effective in improving the nutritive quality of maize silage when applied at ensiling. However, the biochemical properties of enzymes (i.e., enzymic activities, optimum pH) may have a crucial role in dictating the nature of the responses. (C) 2003 Elsevier B.V. All rights reserved.

In vitro evaluation of fibrolytic enzymes as additives for maize (Zea mays L.) silage - II. Effects on rate of acidification, fibre degradation during ensiling and rumen fermentation

A study was carried out to determine the influence of fibrolytic enzymes derived from mesophilic or thermophilic fungal sources, added at ensiling, on time-course fermentation characteristics and in vitro rumen degradation of maize silage. The mesophilic enzyme was a commercial product derived from Trichodenna reesei (L), whereas the thermophilic enzyme was a crude extract produced from Thermoascus aurantiacus (Ta) in this laboratory. The fungus was cultured using maize cobs as a carbon source. The resulting fermentation extract was deionised to remove sugars and characterised for its protein concentration, main and side enzymic activities, optimal pH, protein molecular mass and isoelectric point. In an additional study, both enzymes were added to maize forage (333.5 g DM/kg, 70.0, 469.8, 227.1 and 307.5 g/kg DM of CP, NDF, ADF and starch, respectively) at two levels each, normalized according to xylanase activity, and ensiled in 0.5 kg capacity laboratory minisilos. Duplicate silos were opened at 2, 4, 8, 15, and 60 days after ensiling, and analysed for chemical characteristics. Silages from 60 days were bulked and in vitro gas production (GP) and organic matter degradability (OMD) profiles evaluated using the Reading Pressure Technique (RPT), in a completely randomised design. The crude enzyme extract contained mainly xylanase and endoglucanase activities, with very low levels of exoglucanase, which probably limited hydrolysis of filter paper. The extract contained three major protein bands of between 29 and 55 kDa, with mainly acidic isoelectric points. Ensiling maize with enzymes lowered (P < 0.05) the final silage pH, with this effect being observed throughout the ensiling process. All enzyme treatments reduced (P < 0.05) ADF contents. Treatments including Ta produced more gas (P < 0.05) than the controls after 24 h incubation in vitro, whereas end point gas production at 96 h was not affected. Addition of Ta increased (P < 0.01) OMD after 12 h (410 and 416 g/kg versus 373 g/kg), whereas both L and Ta increased (P < 0.05) OMD after 24 h. Addition of enzymes from mesophilic or thermophilic sources to maize forage at ensiling increased the rate of acidification of the silages and improved in vitro degradation kinetics, suggesting an improvement in the nutritive quality. (C) 2003 Elsevier B.V All rights reserved.

In vitro evaluation of fibrolytic enzymes as additives for maize (Zea mays L.) silage - III. Comparison of enzymes derived from psychrophilic, mesophilic or thermophilic sources

A completely randomised study was completed to examine the influence of fibrolytic enzymes derived from psychrophilic, (F), mesophilic, (L) or thermophilic (Ta) sources, applied at ensiling, on the chemical characteristics and in vitro rumen fermentation of maize silage, assessed using the Reading Pressure Technique (RPT). Treatments, all in triplicate, consisted of untreated maize forage or treated with preparations F, L, Ta or a mixture (1: 1, v/v) of F and L (FL), at two levels each, and ensiled for 210 days in plastic mini-silos. Addition of enzymes L decreased (P < 0.05) silage pH relative to the control, whereas enzyme Ta tended (P < 0.10) to reduce it. Preparations F, L and Ta tended to reduce (P < 0.10) the fibre contents of the silages, with effects being attributable to a decrease in the cellulose fraction. Starch contents were reduced (P < 0.05) in the treatments including enzyme F. End-point (96 h) gas production (GP) values did not differ among treatments, suggesting that enzymes did not change the total amount of fermentable substrate. However, consistent with the decrease in starch contents, adding enzyme F reduced (P < 0.05) GP at most incubation times. Addition of enzymes increased (P < 0.05) the initial (6 h) organic matter degradation (OMD) levels in all but one treatment (F), with increases of 14, 19, and 26% for preparations L, Ta, and FL, respectively, averaged across levels. Furthermore, the addition of enzymes increased (P < 0.05) the soluble OM losses, however, these increases did not fully account for the initial increase in OMD. The latter suggests that enzymes increased solubility and also altered silage structure, making it more amenable to degradation by ruminal microorganisms. As a result of the increase in OMD, without a concomitant increase in GP, the fermentation efficiency was greatly increased (P < 0.05) in enzyme treatments. Addition of enzymes to maize at ensiling, particularly those from the mesophilic and thermophilic sources used here, have the potential to increase the initial rate of silage OMD. (C) 2003 Elsevier B.V. All rights reserved.