Muffler characterization with implementation of the finite element method and experimental techniques

Determining how an exhaust system will perform acoustically before a prototype muffler is built can save the designer both a substantial amount of time and resources. In order to effectively use the simulation tools available it is important to understand what is the most effective tool for the intended purpose of analysis as well as how typical elements in an exhaust system affect muffler performance. An in-depth look at the available tools and their most beneficial uses are presented in this thesis. A full parametric study was conducted using the FEM method for typical muffler elements which was also correlated to experimental results. This thesis lays out the overall ground work on how to accurately predict sound pressure levels in the free field for an exhaust system with the engine properties included. The accuracy of the model is heavily dependent on the correct temperature profile of the model in addition to the accuracy of the source properties. These factors will be discussed in detail and methods for determining them will be presented. The secondary effects of mean flow, which affects both the acoustical wave propagation and the flow noise generation, will be discussed. Effective ways for predicting these secondary effects will be described. Experimental models will be tested on a flow rig that showcases these phenomena.

NetCDF based data archiving system applied to ITER Fast Plant System Control prototype

EURATOM/CIEMAT and Technical University of Madrid (UPM) have been involved in the development of a FPSC [1] (Fast Plant System Control) prototype for ITER, based on PXIe (PCI eXtensions for Instrumentation). One of the main focuses of this project has been data acquisition and all the related issues, including scientific data archiving. Additionally, a new data archiving solution has been developed to demonstrate the obtainable performances and possible bottlenecks of scientific data archiving in Fast Plant System Control. The presented system implements a fault tolerant architecture over a GEthernet network where FPSC data are reliably archived on remote, while remaining accessible to be redistributed, within the duration of a pulse. The storing service is supported by a clustering solution to guaranty scalability, so that FPSC management and configuration may be simplified, and a unique view of all archived data provided. All the involved components have been integrated under EPICS [2] (Experimental Physics and Industrial Control System), implementing in each case the necessary extensions, state machines and configuration process variables. The prototyped solution is based on the NetCDF-4 [3] and [4] (Network Common Data Format) file format in order to incorporate important features, such as scientific data models support, huge size files management, platform independent codification, or single-writer/multiple-readers concurrency. In this contribution, a complete description of the above mentioned solution is presented, together with the most relevant results of the tests performed, while focusing in the benefits and limitations of the applied technologies.

A prototype from the Solar Decathlon Competition becomes an educational building in sustanaible architecture

In 2008, the City Council of Rivas-Vaciamadrid (Spain) decided to promote the construction of “Rivasecopolis”, a complex of sustainable buildings in which a new prototype of a zero-energy house would become the office of the Energy Agency. According to the initiative of the City Council, it was decided to recreate the dwelling prototype “Magic-box” which entered the 2005 Solar Decathlon Competition. The original project has been adapted to a new necessities programme, by adding the necessary spaces that allows it to work as an office. A team from university has designed and carried out the direction of the construction site. The new Solar House is conceived as a “testing building”. It is going to become the space for attending citizens in all questions about saving energy, energy efficiency and sustainable construction, having a permanent small exhibition space additional to the working places for the information purpose. At the same time, the building includes the use of experimental passive architecture systems and a monitoring and control system. Collected data will be sent to University to allow developing research work about the experimental strategies included in the building. This paper will describe and analyze the experience of transforming a prototype into a real durable building and the benefits for both university and citizens in learning about sustainability with the building

Amplificador de señal analógico basado en conceptos biomiméticos. Desarrollo de modelos computacionales y validación experimental

La presente tesis doctoral estudia las características de un transductor acústico bioinspirado en la estructura del maxilar inferior de un Zifio de Couvier (Ziphius cavirostris). El mecanismo de funcionamiento del sensor se basa en las características de un sistema acoplado formado por los distintos componentes acústicos identificados en el maxilar. Para analizar las características del sensor se propone un modelo simplificado 2D que consta de una cavidad cerrada con forma de bocina acoplada a una lengüeta. Una parte de la lengüeta se encuentra dentro de la cavidad y otra en el exterior. Dicha lengüeta detecta los cambios de presión acústica y las vibraciones generadas por el sonido y las transmite con ondas de flexión al interior de la cavidad. La excitación prolongada sobre la placa puede provocar la activación de los modos propios del sistema acoplado. Dichos modos se caracterizan porque presentan un máximo de presión en el cono de la bocina la cual a su vez actúa como un amplificador acústico. Mediante el Método de los elementos Finitos se analizan las características acústicas del sensor y se construye un prototipo experimental para validar los resultados evaluados en el modelo numérico. Se propone una metodología numérica que permite desarrollar y validar un elemento tetraédrico para caracterizar el comportamiento isotrópico de los medios porosos. La metodología permite construir elementos de línea y bidimensionales. A partir de esta metodología se desarrolla un elemento plano ortotrópico. Se realiza un modelo de la cavidad en el que una de las paredes de la bocina está constituida por material poroso y se une la parte exterior de la lengüeta a dicho material para que constituya una viga sobre un apoyo elástico. Se calcula la respuesta modal y se discuten los efectos del material poroso en la eficiencia del transductor y las posibles mejoras a introducir en el mismo. SUMMARY This Thesis studies the characteristics of an acoustic transducer bioinspired by the structure of the lower maxilla of an odontoceto. In this case a Cuvier’s beaked whale (Ziphius cavirostris). The transducer working mechanism is based in a coupled system, with components identified in the maxilla. To analyze the transducer a simplified 2D model composed by a horn shaped closed cavity is modeled. The cavity is coupled with a flat belt. The belt has one part inside the cavity and the other part outside of it. The belt traverses the cavity wall and it is in charge to pick the vibrations from outside and introduce it inside the cavity. The transmission is obtained through the belt bending. A sustained external load with the right frequency contents will allow the system to reach a stationary pressure intensity distribution inside the cavity. Frequencies with modal shapes that show an important intensity increase at the horn tip are of special interest because of the signal amplification. A finite element model is constructed to study the transducer coupled modes and a prototype is constructed to validate the numerical results. A numerical methodology to construct and validate a tetrahedral finite element for isotropic porous materials is presented. The methodology allows constructing linear and 2D elements. It is extended to model orthotropic porous materials behavior. At the end, one of the horn walls is made of an orthotropic material and the external belt is glued to it in order to configure a belt over an elastic foundation. Modal response is evaluated and the porous material effects in the transducer efficiency and further improvements are discussed.

Automatic-dependent surveillance-broadcast experimental deployment using system wide information management

This paper describes an automatic-dependent surveillance-broadcast (ADS-B) implementation for air-to-air and ground-based experimental surveillance within a prototype of a fully automated air traffic management (ATM) system, under a trajectory-based-operations paradigm. The system is built using an air-inclusive implementation of system wide information management (SWIM). This work describes the relations between airborne and ground surveillance (SURGND), the prototype surveillance systems, and their algorithms. System's performance is analyzed with simulated and real data. Results show that the proposed ADS-B implementation can fulfill the most demanding surveillance accuracy requirements.

Exploring polysilicon deposition conditions through a laboratory CVD prototype

Cost and energy consumption related to obtaining polysilicon impact significantly on the total photovoltaic module cost and its energy payback time. Process simplifications can be performed, leading to cost reductions. Nowadays, among several approaches currently pursued to produce the so called Solar Grade Silicon, the chemical route, named Siemens process, is the dominant one. At the Instituto de Energía Solar research on this topic is focused on the chemical route, in particular on the polysilicon deposition step by chemical vapor deposition (CVD) from Trichlorosilane through a laboratory prototype. Valuable information about the phenomena involved in the polysilicon deposition process and the operating conditions is obtained from our experiments. A particular feature of our system is the inclusion of a mass spectrometer. The present work comprises spectra characterization of the polysilicon deposition chemical reaction, temperature and inlet gas mixture composition influence on the deposition rate and analysis of polysilicon deposition conditions for the ?pop-corn' phenomenon to appear, based on experimental experience (Actas de la Special Issue: E-MRS 2012 Spring Meeting ? Symposium A

Estudio experimental sobre la efectividad y la viabilidad de distintas soluciones constructivas para reducir la concentración de gas radón en edificaciones

El trabajo de investigación desarrollado que ha dado lugar a la realización de esta Tesis, aborda la protección de los edificios frente a la entrada de gas radón y su acumulación en los espacios habitados. Dicho gas (isótopo del radón Rn-222) es un elemento radiactivo que se genera, principalmente, en terrenos con altos contenidos de radio (terrenos graníticos por ejemplo). Su alto grado de movilidad permite que penetre en los edificios a través de los materiales de cerramiento del mismo (porosidad de los materiales, fisuras, grietas y juntas) y se acumule en su interior, donde puede ser inhalado en altas concentraciones. La Organización Mundial de la Salud, califica al radón como agente cancerígeno de grado 1. Según este Organismo, el radón es la segunda causa de contracción de cáncer pulmonar detrás del tabaco. Como respuesta a esta alarma, distintos estados ya han elaborado normativas en las que se proponen soluciones para que los niveles de concentración de radón no superen los valores recomendados por los organismos internacionales responsables de la protección radiológica. En España aún no existe normativa de protección frente a este agente cancerígeno causante de numerosas muertes, y es por tal motivo evidente la necesidad de aportar documentación técnica que ayude a las administraciones nacionales y locales a desarrollar dicha normativa para ajustarse a las recomendaciones europeas e internacionales sobre los niveles que no se deben superar y que, por otro lado, ya han contemplado una gran cantidad de países. Como principal aportación de este trabajo se muestran los resultados de reducción de concentración de gas radón de distintas soluciones constructivas enfocadas a frenar la entrada de gas radón al interior de los edificios haciendo uso de técnicas y materiales habituales en el ámbito de la construcción en España. Para ello, se han estudiado las efectividades de dichas soluciones, en lo referente a su capacidad para frenar la inmisión de radón, en un prototipo de vivienda construido al efecto en un terreno con altas concentraciones de radón. Las soluciones propuestas y ensayadas han sido el resultado de una labor de optimización de los sistemas estudiados en la bibliografía con el fin de adaptar las técnicas a los sistemas constructivos habituales en España y en concreto a la situación real del prototipo de vivienda construido en un lugar con contenidos de radón en terreno muy elevados. El trabajo incluye un capítulo inicial con los conceptos básicos necesarios para entender la problemática que supone habitar en espacios con altos contenidos de radón. ABSTRACT The research developed, which has led to the completion of this thesis, deal with the protection of buildings against entry of radon gas and its accumulation in the ocupated spaces. This gas (radon isotope Rn-222) is a radioactive element generated, mainly, in areas with high levels of radio (granitic terrain for example). Its high mobility allows entering in buildings through the enclosure materials of it (porosity of materials, cracks, crevices and joints) and accumulates inside, where it can be inhaled in high concentrations. The World Health Organization describes radon gas as a carcinogen agent in level 1. According to this Agency, radon is the second leading cause of lung cancer behind tobacco. In response to this alarm, some states have developed regulations that propose solutions to reduce radon concentration levels for not exceeding the values recommended by international agencies responsible in radiation protection. In Spain there is still no legislation to protect against this carcinogen element that cause numerous deaths, and for that reason it is evident the need to provide technical documentation to help the national and local governments to develop legislation for reaching the European and international levels recommendations. As the main contribution of this work are the results of reducing radon concentration using different constructive solutions aimed to stop radon entry in buildings, with techniques and materials common in Spain. To do this, effectiveness of such solutions, have been studied in terms of its ability to stop radon entry in a housing prototype built for this purpose in an area with high radon levels. The solutions proposed and tested have been the result of a process of optimization of systems studied in the literature in order to adapt the techniques to Spanish building material and, specifically, to the actual situation of housing prototype built in a place with high contents of radon in soil. The work includes an initial chapter with the basic concepts needed to understand the problem of living in areas with high levels of radon.

Lateral impact sensor for measuring firmness of fruits in an experimental packing line.

Different parameters are used to quantify the maturity of fruits at or near harvest (shape, color, flesh texture and internal composition). Flesh firmness is a critical handling parameter for fruits such as peach, pear and apple. Results of previous studies conducted by different researchers have shown that impact techniques can be used to evaluate firmness of fruits. A prototype impact system for firmness sorting of fruits was developed by Chen and Ruiz-Altisent (Chen et al, 1996). This sensor was mounted and tested successfully on a 3 m section of a commercial conveyor belt (Chen et al, 1998). This is a further development of the on-line impact system for firmness sorting of fruits. The design of the sensor has been improved and it has been mounted on a experimental fruit packing line (Ortiz-Cañavate et al 1999).

High power beam dump project for the accelerator prototype LIPAc: Cooling design and analysis

En el campo de la fusión nuclear y desarrollándose en paralelo a ITER (International Thermonuclear Experimental Reactor), el proyecto IFMIF (International Fusion Material Irradiation Facility) se enmarca dentro de las actividades complementarias encaminadas a solucionar las barreras tecnológicas que aún plantea la fusión. En concreto IFMIF es una instalación de irradiación cuya misión es caracterizar materiales resistentes a condiciones extremas como las esperadas en los futuros reactores de fusión como DEMO (DEMOnstration power plant). Consiste de dos aceleradores de deuterones que proporcionan un haz de 125 mA y 40 MeV cada uno, que al colisionar con un blanco de litio producen un flujo neutrónico intenso (1017 neutrones/s) con un espectro similar al de los neutrones de fusión [1], [2]. Dicho flujo neutrónico es empleado para irradiar los diferentes materiales candidatos a ser empleados en reactores de fusión, y las muestras son posteriormente examinadas en la llamada instalación de post-irradiación. Como primer paso en tan ambicioso proyecto, una fase de validación y diseño llamada IFMIFEVEDA (Engineering Validation and Engineering Design Activities) se encuentra actualmente en desarrollo. Una de las actividades contempladas en esta fase es la construcción y operación de una acelarador prototipo llamado LIPAc (Linear IFMIF Prototype Accelerator). Se trata de un acelerador de deuterones de alta intensidad idéntico a la parte de baja energía de los aceleradores de IFMIF. Los componentes del LIPAc, que será instalado en Japón, son suministrados por diferentes países europeos. El acelerador proporcionará un haz continuo de deuterones de 9 MeV con una potencia de 1.125 MW que tras ser caracterizado con diversos instrumentos deberá pararse de forma segura. Para ello se requiere un sistema denominado bloque de parada (Beam Dump en inglés) que absorba la energía del haz y la transfiera a un sumidero de calor. España tiene el compromiso de suministrar este componente y CIEMAT (Centro de Investigaciones Energéticas Medioambientales y Tecnológicas) es responsable de dicha tarea. La pieza central del bloque de parada, donde se para el haz de iones, es un cono de cobre con un ángulo de 3.5o, 2.5 m de longitud y 5 mm de espesor. Dicha pieza está refrigerada por agua que fluye en su superficie externa por el canal que se forma entre el cono de cobre y otra pieza concéntrica con éste. Este es el marco en que se desarrolla la presente tesis, cuyo objeto es el diseño del sistema de refrigeración del bloque de parada del LIPAc. El diseño se ha realizado utilizando un modelo simplificado unidimensional. Se han obtenido los parámetros del agua (presión, caudal, pérdida de carga) y la geometría requerida en el canal de refrigeración (anchura, rugosidad) para garantizar la correcta refrigeración del bloque de parada. Se ha comprobado que el diseño permite variaciones del haz respecto a la situación nominal siendo el flujo crítico calorífico al menos 2 veces superior al nominal. Se han realizado asimismo simulaciones fluidodinámicas 3D con ANSYS-CFX en aquellas zonas del canal de refrigeración que lo requieren. El bloque de parada se activará como consecuencia de la interacción del haz de partículas lo que impide cualquier cambio o reparación una vez comenzada la operación del acelerador. Por ello el diseño ha de ser muy robusto y todas las hipótesis utilizadas en la realización de éste deben ser cuidadosamente comprobadas. Gran parte del esfuerzo de la tesis se centra en la estimación del coeficiente de transferencia de calor que es determinante en los resultados obtenidos, y que se emplea además como condición de contorno en los cálculos mecánicos. Para ello por un lado se han buscado correlaciones cuyo rango de aplicabilidad sea adecuado para las condiciones del bloque de parada (canal anular, diferencias de temperatura agua-pared de decenas de grados). En un segundo paso se han comparado los coeficientes de película obtenidos a partir de la correlación seleccionada (Petukhov-Gnielinski) con los que se deducen de simulaciones fluidodinámicas, obteniendo resultados satisfactorios. Por último se ha realizado una validación experimental utilizando un prototipo y un circuito hidráulico que proporciona un flujo de agua con los parámetros requeridos en el bloque de parada. Tras varios intentos y mejoras en el experimento se han obtenido los coeficientes de película para distintos caudales y potencias de calentamiento. Teniendo en cuenta la incertidumbre de las medidas, los valores experimentales concuerdan razonablemente bien (en el rango de 15%) con los deducidos de las correlaciones. Por motivos radiológicos es necesario controlar la calidad del agua de refrigeración y minimizar la corrosión del cobre. Tras un estudio bibliográfico se identificaron los parámetros del agua más adecuados (conductividad, pH y concentración de oxígeno disuelto). Como parte de la tesis se ha realizado asimismo un estudio de la corrosión del circuito de refrigeración del bloque de parada con el doble fin de determinar si puede poner en riesgo la integridad del componente, y de obtener una estimación de la velocidad de corrosión para dimensionar el sistema de purificación del agua. Se ha utilizado el código TRACT (TRansport and ACTivation code) adaptándalo al caso del bloque de parada, para lo cual se trabajó con el responsable (Panos Karditsas) del código en Culham (UKAEA). Los resultados confirman que la corrosión del cobre en las condiciones seleccionadas no supone un problema. La Tesis se encuentra estructurada de la siguiente manera: En el primer capítulo se realiza una introducción de los proyectos IFMIF y LIPAc dentro de los cuales se enmarca esta Tesis. Además se describe el bloque de parada, siendo el diseño del sistema de rerigeración de éste el principal objetivo de la Tesis. En el segundo y tercer capítulo se realiza un resumen de la base teórica así como de las diferentes herramientas empleadas en el diseño del sistema de refrigeración. El capítulo cuarto presenta los resultados del relativos al sistema de refrigeración. Tanto los obtenidos del estudio unidimensional, como los obtenidos de las simulaciones fluidodinámicas 3D mediante el empleo del código ANSYS-CFX. En el quinto capítulo se presentan los resultados referentes al análisis de corrosión del circuito de refrigeración del bloque de parada. El capítulo seis se centra en la descripción del montaje experimental para la obtención de los valores de pérdida de carga y coeficiente de transferencia del calor. Asimismo se presentan los resultados obtenidos en dichos experimentos. Finalmente encontramos un capítulo de apéndices en el que se describen una serie de experimentos llevados a cabo como pasos intermedios en la obtención del resultado experimental del coeficiente de película. También se presenta el código informático empleado para el análisis unidimensional del sistema de refrigeración del bloque de parada llamado CHICA (Cooling and Heating Interaction and Corrosion Analysis). ABSTRACT In the nuclear fusion field running in parallel to ITER (International Thermonuclear Experimental Reactor) as one of the complementary activities headed towards solving the technological barriers, IFMIF (International Fusion Material Irradiation Facility) project aims to provide an irradiation facility to qualify advanced materials resistant to extreme conditions like the ones expected in future fusion reactors like DEMO (DEMOnstration Power Plant). IFMIF consists of two constant wave deuteron accelerators delivering a 125 mA and 40 MeV beam each that will collide on a lithium target producing an intense neutron fluence (1017 neutrons/s) with a similar spectra to that of fusion neutrons [1], [2]. This neutron flux is employed to irradiate the different material candidates to be employed in the future fusion reactors, and the samples examined after irradiation at the so called post-irradiative facilities. As a first step in such an ambitious project, an engineering validation and engineering design activity phase called IFMIF-EVEDA (Engineering Validation and Engineering Design Activities) is presently going on. One of the activities consists on the construction and operation of an accelerator prototype named LIPAc (Linear IFMIF Prototype Accelerator). It is a high intensity deuteron accelerator identical to the low energy part of the IFMIF accelerators. The LIPAc components, which will be installed in Japan, are delivered by different european countries. The accelerator supplies a 9 MeV constant wave beam of deuterons with a power of 1.125 MW, which after being characterized by different instruments has to be stopped safely. For such task a beam dump to absorb the beam energy and take it to a heat sink is needed. Spain has the compromise of delivering such device and CIEMAT (Centro de Investigaciones Energéticas Medioambientales y Tecnológicas) is responsible for such task. The central piece of the beam dump, where the ion beam is stopped, is a copper cone with an angle of 3.5o, 2.5 m long and 5 mm width. This part is cooled by water flowing on its external surface through the channel formed between the copper cone and a concentric piece with the latter. The thesis is developed in this realm, and its objective is designing the LIPAc beam dump cooling system. The design has been performed employing a simplified one dimensional model. The water parameters (pressure, flow, pressure loss) and the required annular channel geometry (width, rugoisty) have been obtained guaranteeing the correct cooling of the beam dump. It has been checked that the cooling design allows variations of the the beam with respect to the nominal position, being the CHF (Critical Heat Flux) at least twice times higher than the nominal deposited heat flux. 3D fluid dynamic simulations employing ANSYS-CFX code in the beam dump cooling channel sections which require a more thorough study have also been performed. The beam dump will activateasaconsequenceofthe deuteron beam interaction, making impossible any change or maintenance task once the accelerator operation has started. Hence the design has to be very robust and all the hypotheses employed in the design mustbecarefully checked. Most of the work in the thesis is concentrated in estimating the heat transfer coefficient which is decisive in the obtained results, and is also employed as boundary condition in the mechanical analysis. For such task, correlations which applicability range is the adequate for the beam dump conditions (annular channel, water-surface temperature differences of tens of degrees) have been compiled. In a second step the heat transfer coefficients obtained from the selected correlation (Petukhov- Gnielinski) have been compared with the ones deduced from the 3D fluid dynamic simulations, obtaining satisfactory results. Finally an experimental validation has been performed employing a prototype and a hydraulic circuit that supplies a flow with the requested parameters in the beam dump. After several tries and improvements in the experiment, the heat transfer coefficients for different flows and heating powers have been obtained. Considering the uncertainty in the measurements the experimental values agree reasonably well (in the order of 15%) with the ones obtained from the correlations. Due to radiological reasons the quality of the cooling water must be controlled, hence minimizing the copper corrosion. After performing a bibligraphic study the most adequate water parameters were identified (conductivity, pH and dissolved oxygen concentration). As part of this thesis a corrosion study of the beam dump cooling circuit has been performed with the double aim of determining if corrosion can pose a risk for the copper beam dump , and obtaining an estimation of the corrosion velocitytodimension the water purification system. TRACT code(TRansport and ACTivation) has been employed for such study adapting the code for the beam dump case. For such study a collaboration with the code responsible (Panos Karditsas) at Culham (UKAEA) was established. The work developed in this thesis has supposed the publication of three articles in JCR journals (”Journal of Nuclear Materials” y ”Fusion Engineering and Design”), as well as presentations in more than four conferences and relevant meetings.

Experimental evidence of super-resolution better than lambda/105 with positive refraction

Super-resolution (SR) systems surpassing the Abbe diffraction limit have been theoretically and experimentally demonstrated using a number of different approaches and technologies: using materials with a negative refractive index, utilizing optical super-oscillation, using a resonant metalens, etc. However, recently it has been proved theoretically that in the Maxwell fish-eye lens (MFE), a device made of positive refractive index materials, the same phenomenon takes place. Moreover, using a simpler device equivalent to the MFE called the spherical geodesic waveguide (SGW), an SR of up to λ/3000 was simulated in COMSOL. Until now, only one piece of experimental evidence of SR with positive refraction has been reported (up to λ/5) for an MFE prototype working at microwave frequencies. Here, experimental results are presented for an SGW prototype showing an SR of up to λ/105. The SGW prototype consists of two concentric metallic spheres with an air space in between and two coaxial ports acting as an emitter and a receiver. The prototype has been analyzed in the range 1 GHz to 1.3 GHz.

Low-Cost Radar-Based Target Identification Prototype using an Expert System

Smart and green cities are hot topics in current research because people are becoming more conscious about their impact on the environment and the sustainability of their cities as the population increases. Many researchers are searching for mechanisms that can reduce power consumption and pollution in the city environment. This paper addresses the issue of public lighting and how it can be improved in order to achieve a more energy efficient city. This work is focused on making the process of turning the streetlights on and off more intelligent so that they consume less power and cause less light pollution. The proposed solution is comprised of a radar device and an expert system implemented on a low-cost platform based on a DSP. By analyzing the radar echo in both the frequency and time domains, the system is able to detect and identify objects moving in front of it. This information is used to decide whether or not the streetlight should be turned on. Experimental results show that the proposed system can provide hit rates over 80%, promising a good performance. In addition, the proposed solution could be useful in kind of other applications such as intelligent security and surveillance systems and home automation.

Estudio y validación experimental del efecto de aire interno en un perfil aerodinámico hueco

La presente investigación se llevó a cabo en la Universidad Politécnica de Madrid (España) conjuntamente con la Universidad Nacional Experimental del Táchira (Venezuela). El estudio consistió en diseñar una cavidad interna dentro del perfil aerodinámico 2415-3s, el cual fue desarrollado en la Universidad Técnica Checa (Praga, República Checa). Se realizó un estudio computacional, mediante la técnica del CFD, de diferentes modelos de cavidades internas en este perfil, para seleccionar el diseño más adecuado, fabricando un prototipo en 3D; logrando de esta manera validar la simulación computacional con los datos experimentales obtenidos con los ensayos en el túnel de viento AF6109 de la Universidad Nacional Experimental del Táchira. También se aplicaron técnicas de visualización en el túnel de viento, como líneas de corriente de humo y películas de aceite sobre el perfil aerodinámico. Dicho procedimiento permitió corroborar la validación de la simulación computacional. El perfil aerodinámico seleccionado se denominó 2415-3s-TC, cuya característica principal consiste en tres canales independientes entre sí, alojados dentro de la cavidad interna, permitiendo que el flujo de aire forzado a través de la cavidad, cambiara de dirección, para desembocar lo más tangencialmente, así como, lo más perpendicularmente posible al escalón del perfil aerodinámico 2415-3s. Esta configuración de diseñó permitió elevar el coeficiente de sustentación para ángulos de ataque mayores a 8º, así como para ángulos cercanos al ángulo crítico. ABSTRACT This research was conducted at the Polytechnic University of Madrid (Spain) together with the National Experimental University of Táchira (Venezuela). The study was to design an internal cavity within the airfoil 2415-3s, which was developed in the Czech Technical University (Prague, Czech Republic). A computational study was performed using CFD technique, different models of internal cavities in the profile to select the most appropriate design, manufacturing a prototype 3D; thus achieving validate the computer simulation with experimental data obtained from the tests in the wind tunnel AF6109 of the National Experimental University of Táchira. Visualization techniques were also applied in the wind tunnel, as streamlines smoke and oil films on the airfoil. This procedure corroborated validation of computational simulation. The airfoil selected denominated 2415-3s-TC, whose main characteristic consists of three independent channels each other, housed within the inner cavity, allowing the forced air flow through the cavity, change direction, to lead as more tangentially and, as perpendicular as possible to the step 2415-3s aerofoil. This configuration designed allowed increasing the lift coefficient for higher angles of attack to 8º, and for angles near the critical angle.

Vivienda y Revolución. El Concurso entre Camaradas de la OSA, la Sección de Tipificación del Stroykom y la Casa Experimental de Transición Narkomfin (1926-1930) = Housing and Revolution. OSA’s Comradely Competition, Typification Section of the Stroykom and Narkomfin Experimental Transitional House (1926-1930)

La cuestión del asentamiento socialista en la URSS durante la década de 1920 estuvo caracterizada por el objetivo de definir y establecer un estado socialista en términos políticos, sociales y económicos. En este contexto de inestabilidad y cambio, un grupo de arquitectos pertenecientes a la Asociación de Arquitectos Contemporáneos, OSA, y liderado por Moisey Ginzburg, abordó el tema de la vivienda obrera asumiendo la responsabilidad y el compromiso por alcanzar un nuevo orden social. Su misión no consistió únicamente en solucionar el problema del alojamiento para los trabajadores en las grandes ciudades soviéticas, sino en redefinirlo como el marco adecuado para una sociedad sometida a un cambio sin precedentes que, al mismo tiempo y en un proceso dialéctico, debía contribuir a la construcción de esa nueva sociedad. La respuesta dada por la OSA trascendió el diseño inmediato bajo los estándares modernos establecidos en Occidente y tomó forma en un proceso de investigación que habría de prolongarse durante cinco años. Este trabajo, que culminó con la construcción y puesta en crisis de la Casa Narkomfin, se desarrolló en tres aproximaciones sucesivas. La primera, de carácter conceptual, consideró la participación ciudadana, así como de especialistas independientes, formalizándose en el Concurso entre Camaradas convocado por la OSA en 1926. La segunda aproximación al problema de la vivienda obrera se articuló a través de la investigación llevada a cabo por la Sección de Tipificación del Stroykom, esta vez desde premisas científicas y metodológicas. Finalmente, las conclusiones alcanzadas fueron transferidas a la práctica arquitectónica por medio de la construcción de seis Casas Experimentales de Transición, entre las que destacó la Casa Narkomfin. Este último acercamiento, de carácter empírico, ha sido tradicionalmente examinado por los expertos como un hecho aislado. Sin embargo, su estudio debe trascender necesariamente el genio del autor-creador en favor del proceso de investigación al que pertenece. En esta tesis, la Casa Narkomfin no se presenta sólo como el paradigma de vivienda soviética de vanguardia al que estamos acostumbrados, sino como un prototipo que recoge los principios y conclusiones alcanzados en las aproximaciones conceptuales y científicas precedentes. Únicamente desde este punto de vista cobra sentido la consideración de Ginzburg sobre su propio edificio como un medio propositivo y no impositivo: un proyecto concebido como una herramienta de transición hacia una sociedad más avanzada. ABSTRACT The question of mass housing in the USSR during the Twenties was marked by the drive to define and establish a socialist state in political, social and economic terms. In this context of instability and change, a group of architects gathered together under the Association of Contemporary Architects, OSA, led by Moisey Ginzburg, to address the issue of mass housing, thus taking on the responsibility and being committed to creating a new social order. Their quest not only involved solving the problem of housing for workers in large Soviet cities, but also redefining this solution as an appropriate framework for a society undergoing dramatic changes which, at the same time and in a dialectical process, would contribute to the creation of this new society. The solution provided by OSA transcended Modern standards of immediate design set by the West and was the result of a research process that would last five years. This work culminated in the construction of Narkomfin House and its self-criticism, developed in three successive approaches. The first was conceptual, being formalized in the Comradely Competition held by the OSA in 1926 and taking into account the participation of citizens and independent experts. The second approach to the problem of mass housing involved research developed by the Typification Section of the Stroykom, this time under scientific and methodological premises. Finally, the conclusions reached were put in practice with the construction of six Experimental Transitional Houses of which the most notable is Narkomfin House. This third empirical approach has traditionally been examined by scholars in isolation. However, its study must necessarily transcend the genius of the author-creator and involve the research process of which it is part. In this thesis, Narkomfin House is presented not only as the paradigm in Soviet housing avant-garde we are used to, but also as a prototype reflecting the principles and conclusions reached in the preceding conceptual and scientific approaches. Only from this point of view does Ginzburg’s understanding of his own building as a proactive and non-imposed environment make sense: a project conceived as a transition tool towards a more advanced society.

Photoactive yellow protein: A structural prototype for the three-dimensional fold of the PAS domain superfamily

PAS domains are found in diverse proteins throughout all three kingdoms of life, where they apparently function in sensing and signal transduction. Although a wealth of useful sequence and functional information has become recently available, these data have not been integrated into a three-dimensional (3D) framework. The very early evolutionary development and diverse functions of PAS domains have made sequence analysis and modeling of this protein superfamily challenging. Limited sequence similarities between the ∼50-residue PAS repeats and one region of the bacterial blue-light photosensor photoactive yellow protein (PYP), for which ground-state and light-activated crystallographic structures have been determined to high resolution, originally were identified in sequence searches using consensus sequence probes from PAS-containing proteins. Here, we found that by changing a few residues particular to PYP function, the modified PYP sequence probe also could select PAS protein sequences. By mapping a typical ∼150-residue PAS domain sequence onto the entire crystallographic structure of PYP, we show that the PAS sequence similarities and differences are consistent with a shared 3D fold (the PAS/PYP module) with obvious potential for a ligand-binding cavity. Thus, PYP appears to prototypically exhibit all the major structural and functional features characteristic of the PAS domain superfamily: the shared PAS/PYP modular domain fold of ∼125–150 residues, a sensor function often linked to ligand or cofactor (chromophore) binding, and signal transduction capability governed by heterodimeric assembly (to the downstream partner of PYP). This 3D PAS/PYP module provides a structural model to guide experimental testing of hypotheses regarding ligand-binding, dimerization, and signal transduction.

On the suitability of Prototype Selection methods for kNN classification with distributed data

In the current Information Age, data production and processing demands are ever increasing. This has motivated the appearance of large-scale distributed information. This phenomenon also applies to Pattern Recognition so that classic and common algorithms, such as the k-Nearest Neighbour, are unable to be used. To improve the efficiency of this classifier, Prototype Selection (PS) strategies can be used. Nevertheless, current PS algorithms were not designed to deal with distributed data, and their performance is therefore unknown under these conditions. This work is devoted to carrying out an experimental study on a simulated framework in which PS strategies can be compared under classical conditions as well as those expected in distributed scenarios. Our results report a general behaviour that is degraded as conditions approach to more realistic scenarios. However, our experiments also show that some methods are able to achieve a fairly similar performance to that of the non-distributed scenario. Thus, although there is a clear need for developing specific PS methodologies and algorithms for tackling these situations, those that reported a higher robustness against such conditions may be good candidates from which to start.