Direct determination of Al, As, Cu, Fe, Mn, and Ni in fuel ethanol by simultaneous GFAAS using integrated platforms pretreated with W-Rh permanent modifier together with Pd plus Mg modifier

A method is proposed for the simultaneous determination of Al, As, Cu, Fe, Mn, and Ni in fuel ethanol by electrothermal atomic absorption spectrometry (ETAAS) using W-Rh permanent modifier together with Pd(NO3)(2) + Mg(NO3)(2) conventional modifier. The integrated platform of a transversely heated graphite atomizer (THGA) was treated with tungsten, followed by rhodium, forming a deposit containing 250 mug W + 200 mug Rh. A 500-muL, volume of fuel ethanol was diluted with 500 muL, of 0.14 mol L-1 HNO3 in an autosampler cup of the spectrometer. Then, 20 muL, of the diluted ethanol was introduced into the pretreated graphite platform followed by the introduction of 5 mug Pd(NO3)(2) + 3 mug Mg(NO3)(2). The injection of this modifier was required to improve arsenic and iron recoveries in fuel ethanol. Calibrations were carried out using multi-element reference solutions prepared in diluted ethanol (1 + 1, v/v) acidified to 0. 14 mol L-1 HNO3. The pyrolysis and atomization temperatures of the heating program were 1200degreesC and 2200degreesC, respectively, which were obtained with multielement reference solutions in acidic diluted ethanol (1 + 1, v/v; 0. 14 mol L-1 HNO3). The characteristic masses for the simultaneous determination in ethanol fuel were 78 pg Al, 33 pg As, 10 pg Cu, 14 pg Fe, 7 pg Mn, and 24 pg Ni. The lifetime of the pretreated tube was about 700 firings. The detection limits (D.L.) were 1.9 mug L-1 Al, 2.9 mug L-1 As, 0.57 mug L-1.Cu, 1.3 mug L-1 Fe, 0.40 mug L-1 Mn, and 1.3 mug L-1 Ni. The relative standard deviations (n = 12) were 4%, 4%, 3%, 1.5%, 1.2%, and 2.2% for Al, As, Cu, Fe, Mn, and Ni, respectively. The recoveries of Al, As, Cu, Fe, Mn, and Ni added to the fuel ethanol samples varied from 81% to 95%, 80% to 98%, 97% to 109%, 85% to 107%, 98% to 106% and 97% to 103%, respectively. Accuracy was checked for the Al, As, Cu, Fe, Mn, and Ni determination in 10 samples purchased at a local gas station in Araraquara-SP City, Brazil. A paired t-test showed that at the 95% confidence level the results were in agreement with those obtained by single-element ETAAS.

Fecundity of the crab Callinectes ornatus Ordway, 1863 (Decapoda, Brachyura, Portunidae) from the Ubatuba region, São Paulo, Brazil

The objective of the present study was to characterize the fecundity of Callinectes ornatus from the northern coast of São Paulo, Brazil. To study the fecundity and its relationships to size, brood weight, and egg size, the ovigerous females were collected at 2-month intervals for two consecutive years (January, 1991 to November, 1992) in the Ubatuba region using a fishing boat equipped with an otter-trawl type of net. After collecting, the animals were screened, bagged, labeled, and stored frozen. Only data from 38 females carrying early stage eggs were considered. In the laboratory, the specimens were thawed at room temperature, the pleopod structure with the egg mass was removed and the eggs were carefully removed from the pleopods. The samples were then fixed in 10% formalin and stored in 70% ethanol, until the time for processing. Processing followed the method of Hines (1982, 1988). Following the frequency determination of carapace width and fecundity, mean egg number, mean volume and mean dry weight of brooded egg mass were determined for each class obtained. Data were analyzed by regressions of log-log transformations for allometric plots (Y = aX(b)) of reproductive variables versus carapace width. Carapace width was one of the main factors for the determination of fecundity, which ranged 171 570 +/- 94 634 eggs, with females of the same size class presenting a wide amplitude of variation. This supports the hypothesis that portunid females present staggered spawning, possibly presenting more than one period of reproduction within one year. The present species showed lower fecundity than the remaining portunids studied, but they did show a rapid and efficient embryonic development, presumably capable of assuring reproductive success.

Antibacterial properties of propolis and products containing propolis from Brazil

Crude propolis and commercial products containing propolis, such as ethanolic extracts, tablets, capsules and powders acquired in São Paulo City (Brazil) were analyzed. The resins of the solid products were extracted with ethanol and found to be present at various concentrations, independently of the propolis concentration specified on the label of the commercial products. The in vitro activity of these resins against S aureus, B cereus and B subrilis was also determined. The results showed that the antibacterial activity rather than the propolis concentration itself should be considered for quality control and that some resins are likely to display a species-specific action.

Greenhouse gas balance due to the conversion of sugarcane areas from burned to green harvest in Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Development and energy balance of sugarcane in the norte fluminense, Brazil

The growing concern for renewable and cleaner energy sources has increased the demand for biofuels, pointing out the ethanol from sugarcane. The aim of this study was quantify the partition of energy balance components and monitor the physiological development indexes of the sugarcane, relating them to water availability conditions of climate and soil in Campos dos Goytacazes, Norte Fluminense, Brazil. To this end, a micrometeorological station was settled in an area of 13 ha in commercial cultivation. The culture was regularly monitored at 85, 102, 128, 149, 174, 194, 215, 235, 255 and 280 days after cutting (DAC). The variations in water availability directly influenced the rates of crop growth and energy balance. Under the conditions studied most of the available energy (53%) was consumed by the latent heat flux.

The Brazilian experience of sugarcane ethanol industry

Biomass has gained prominence in the last few years as one of the most important renewable energy sources. In Brazil, a sugarcane ethanol program called ProAlcohol was designed to supply the liquid gasoline substitution and has been running for the last 30 yr. The federal government's establishment of ProAlcohol in 1975 created the grounds for the development of a sugarcane industry that currently is one of the most efficient systems for the conversion of photosynthate into different forms of energy. Improvement of industrial processes along with strong sugarcane breeding programs brought technologies that currently support a cropland of 7 million hectares of sugarcane with an average yield of 75 tons/ha. From the beginning of ProAlcohol to the present time, ethanol yield has grown from 2,500 to around 7,000 l/ha. New technologies for energy production from crushed sugarcane stalk are currently supplying 15% of the electricity needs of the country. Projections show that sugarcane could supply over 30% of Brazil's energy needs by 2020. In this review, we briefly describe some historic facts of the ethanol industry, the role of sugarcane breeding, and the prospects of sugarcane biotechnology.

Screening for yeast with antibacterial properties from an ethanol distillery

A general screening for the expression of antibacterial activity and non-flocculating type of yeast strains from must and fermented broth of alcohol distilleries was performed. From 60 strains only Saccharomyces sp. M26 presented a inhibitory halo in Lactobacillus fermentum culture and significant reduction in the culture turbidity (71%) and specific growth rate (56%) when compared to the control. Freezing did not affect the antibacterial activity of the Saccharomyces sp. M26 extract and heating at 90°C for 20 min completely destroyed this activity. It is expected the decrease of lactic acid bacteria growth in the S. cerevisiae alcoholic fermentation should allow for better control of these bacteria in the process. © 2003 Elsevier Ltd. All rights reserved.

Thermodynamic analysis of direct steam reforming of ethanol in molten carbonate fuel cell

Fuel cell as MCFC (molten carbonate fuel cell) operate at high temperatures, and due to this issue, cogeneration processes may be performed, sending heat for own process or other purposes as steam generation in an industry. The use of ethanol for this purpose is one of the best options because this is a renewable and less environmentally offensive fuel, and cheaper than oil-derived hydrocarbons (in the case of Brazil). In the same country, because of technical, environmental and economic advantages, the use of ethanol by steam reforming process have been the most investigated process. The objective of this study is to show a thermodynamic analysis of steam reforming of ethanol, to determine the best thermodynamic conditions where are produced the highest volumes of products, making possible a higher production of energy, that is, a most-efficient use of resources. To attain this objective, mass and energy balances are performed. Equilibrium constants and advance degrees are calculated to get the best thermodynamic conditions to attain higher reforming efficiency and, hence, higher electric efficiency, using the Nernst equation. The advance degree of reforming increases when the operation temperature also increases and when the operation pressure decreases. But at atmospheric pressure (1 atm), the advance degree tends to the stability in temperatures above 700°C, that is, the volume of supplemental production of reforming products is very small for the high use of energy resources necessary. Reactants and products of the steam-reforming of ethanol that weren't used may be used for the reforming. The use of non-used ethanol is also suggested for heating of reactants before reforming. The results show the behavior of MCFC. The current density, at same tension, is higher at 700°C than other studied temperatures as 600 and 650°C. This fact occurs due to smaller use of hydrogen at lower temperatures that varies between 46.8 and 58.9% in temperatures between 600 and 700°C. The higher calculated current density is 280 mA/cm 2. The power density increases when the volume of ethanol to be used also increases due to higher production of hydrogen. The highest produced power at 190 mW/cm 2 is 99.8, 109.8 and 113.7 mW/cm2 for 873, 923 and 973K, respectively. The thermodynamic efficiency has the objective to show the connection among operational conditions and energetic factors, which are some parameters that describes a process of internal steam reforming of ethanol.

Air quality and emissions management in the State of São Paulo, Brazil

The São Paulo State has 36 million people, 25 million living in three metropolitan areas. Only the São Paulo Metropolitan Region (SPMR) includes the state capital (São Paulo City) plus 38 cities, where ≈ 18 million people live, affected by frequent episodes of ozone, NOx, and fine particulate matter. In 2003, it was estimated that 15.1% of the SPMR vehicles used ethanol and 70.2% used the local gasoline. Natural gas vehicles have witnessed a booming participation in the last years, mainly through conversion of gasoline cars, and the present fleet is almost one million vehicles. To face the problems generated by light vehicles emissions the Federal Government set a program called PROCONVE - Program of Air Pollution Control from Vehicles - in 1986 and since then until now a significant reduction was reached, but the growth of the fleet hides most of the emission cuts. A discussion covers the evolution of the air pollution management in São Paulo; and innovative tools for air pollution management - both for mobile and stationary sources. This is an abstract of a paper presented at the 98th AWMA Annual Conference and Exhibition (Minneapolis, MN 6/21-24/2005).

Bioethanol - Brazil, 30 years of Proálcool

Brazil, which has always been in the forefront of sugarcane production, also occupies a prominent position as the first country to produce and use biofuel in its automobile fleet. This fact is a consequence of the introduction of a program which has already turned 30 years, the Próalcool (National Alcohol Program). The oil crisis in the seventies encouraged the government to develop an alternative way to replace gasoline. Bioethanol was then born as fuel obtained from fermentation of sugarcane juice, molasses or both. In the eighties, 85% of the cars ran exclusively on alcohol. Ethanol production in that decade exceeded sugarcane production by the mills. The installed units reached in that period the capacity to produce 18 billion liters of bioethanol per season, a volume equivalent to 100 million barrels of gasoline. The fermentation process, which so far had been restricted to manufacturing sugarcane liquor (aguardente) or ethanol as a byproduct of sugarcane, takes over the spotlight in the entrepreneurial scene. As a result, processes comprising engineering concepts came up and most of the biological phenomena involved in fermentation were understood. The knowledge gathered and the units installed have granted Brazil the hold of production technology and use of a clean fuel.

Economical analysis of ethanol steam reformer for hydrogen production associated with a sugarcane industry

An expressive amount of produced hydrogen is generated by customers in-situ such as petrochemical, fertilizer and sugarcane industries. However, the most utilized feedstock is natural gas, a non-renewable and fossil fuel. The introduction of biohydrogen production process associated in a sugarcane industry is an alternative to diminish emissions and contribute to create a CO2 cycle, where the plants capture this gas by photosynthesis process and produces sucrose for ethanol production. The cost of production of ethanol has dramatically decreased (from about US$ 700/m3 in 1970s to US$ 200/m3 today), becoming this a good option at near term, inclusively for its utilization by customers localized in main regions (localized especially in regions such as Southeastern Brazil) Also in near future, it will possible the utilization of fuel cells as form of distributed generation. Its utilization could occur specially in peak hours, diminishing the cost of investments in newer transmission systems. A technical and economic analysis of steam reformer of ethanol to hydrogen production associated with sugarcane industry was recently performed. This technique will also allow the use of ethanol when its price is relatively low. This study was based on a previous R&D study (sponsored by CEMIG - State of Minas Gerais Electricity Company) where thermodynamic and economic analyses were developed, based in the development of two ethanol steam reformers prototypes.x In this study an analysis was performed considering the use of bagasse as source of heat in the steam reforming process. Its use could to diminish the costs of hydrogen production, especially at large scale, obtaining cost-competitive production and permitting that sugarcane industry produces hydrogen in large scale beyond ethylic alcohol, anhydrous alcohol (or ethanol) and sugar.

Influence of the vinasse application in sugar cane fields in Patrocínio Paulista, São Paulo State, Brazil

This investigation was carried out in Patrocínio Paulista municipality, located in the state of São Paulo, Brazil. Sugarcane has been extensively cultivated in the area in order to be utilized by the sugar and ethanol industries. The major effluent from the ethanol industry, vinasse, has been applied in the sugarcane fields as an alternative to supply several nutrients in crop production. Because it may represent a major environmental problem in that area, with implications to human health, soil samples from six points were collected and analyzed in order to evaluate the main factors related to the vinasse application in the ground. The importance of clays, iron oxides, organic matter and minor refractory minerals was also considered for explaining several relationships identified from the acquired data. © 2009 WIT Press.

Sugarcane (Saccharum X officinarum): A Reference Study for the Regulation of Genetically Modified Cultivars in Brazil

Global interest in sugarcane has increased significantly in recent years due to its economic impact on sustainable energy production. Sugarcane breeding and better agronomic practices have contributed to a huge increase in sugarcane yield in the last 30 years. Additional increases in sugarcane yield are expected to result from the use of biotechnology tools in the near future. Genetically modified (GM) sugarcane that incorporates genes to increase resistance to biotic and abiotic stresses could play a major role in achieving this goal. However, to bring GM sugarcane to the market, it is necessary to follow a regulatory process that will evaluate the environmental and health impacts of this crop. The regulatory review process is usually accomplished through a comparison of the biology and composition of the GM cultivar and a non-GM counterpart. This review intends to provide information on non-GM sugarcane biology, genetics, breeding, agronomic management, processing, products and byproducts, as well as the current technologies used to develop GM sugarcane, with the aim of assisting regulators in the decision-making process regarding the commercial release of GM sugarcane cultivars. © 2011 The Author(s).

Antiviral activity of plants occurring in the state of minas gerais (Brazil): Part III

A total of 24 extracts from 14 plant species collected at the state of Minas Gerais, Brazil, and belonging to five botanical families (Annonaceae, Apocynaceae, Ochnaceae, Polygonaceae and Vitaceae) was screened for cytotoxicity in cultured Vero cells and for antiviral activity against human herpes virus type 1 (HSV-1), vaccinia virus (VACV) and murine encephalomyocarditis virus (EMCV). The highest cytotoxicity (CC 50 < 10 μg/mL) was observed for the ethanol extracts from Annona coriacea fruits and seeds. Extracts from Hancornia speciosa, Ouratea castaneafolia and O. semisrrata were the only ones that have shown activity against all the three viruses assayed. Extracts from Polygonum spectabile, Hancornia speciosa, Himatanthus phagedaenica, Ouratea spectabilis and O. semiserrata were the most active against HSV-1 (EC 50 < 50 mg/mL), with favorable SI values (8.0 to 10.0). Hancornia speciosa and Anaxagorea dolichocarpa were the most active against EMCV (EC 50 50 - 100 μg/mL), with reasonable SI values (5.2 to 6.1), while moderate to low activity (EC 50 > 100 μg/mL) was observed for Ouratea spectabilis and O. semiserrata. A total of 7 plant species, Ouratea semiserrata, O. spectabilis, O. castanaeafolia, Rollinia laurifolia, Cissus erosa, Polygonum spectabile, and Hancornia speciosa, were active against VACV, disclosing EC50 < 50 μg/mL and SI values ranging from 6.6 to 67.3. In total, 10 out of the 14 species were selected from a literature survey on plants used to treat viral diseases in Brazil; these species were responsible for 70% of the positive results.

Evaluation of water amount in hydrated ethanol fuel by gamma-ray attenuation technique

In this work, is presented an alternative and non conventional technique for evaluate the water amount present in the hydrated ethanol used as automotive fuel. The standard technique used in this kind of measure is the use of densimeter. The proposal of this work is based on the measure of the linear attenuation coefficient of hydrated ethanol, using the gamma-ray attenuation technique. The water amount, in volume, can be determined knowing the linear attenuation coefficient of hydrated ethanol. Samples of hydrated ethanol, collected at fuel stations, located in Sorocaba, SP, Brazil, were analyzed and the results showed the feasibility of the technique. © 2011 American Institute of Physics.