The AVOID programme’s new simulations of the global benefits of stringent climate change mitigation

Quantitative simulations of the global-scale benefits of climate change mitigation are presented, using a harmonised, self-consistent approach based on a single set of climate change scenarios. The approach draws on a synthesis of output from both physically-based and economics-based models, and incorporates uncertainty analyses. Previous studies have projected global and regional climate change and its impacts over the 21st century but have generally focused on analysis of business-as-usual scenarios, with no explicit mitigation policy included. This study finds that both the economics-based and physically-based models indicate that early, stringent mitigation would avoid a large proportion of the impacts of climate change projected for the 2080s. However, it also shows that not all the impacts can now be avoided, so that adaptation would also therefore be needed to avoid some of the potential damage. Delay in mitigation substantially reduces the percentage of impacts that can be avoided, providing strong new quantitative evidence for the need for stringent and prompt global mitigation action on greenhouse gas emissions, combined with effective adaptation, if large, widespread climate change impacts are to be avoided. Energy technology models suggest that such stringent and prompt mitigation action is technologically feasible, although the estimated costs vary depending on the specific modelling approach and assumptions.

Simulation study of cascade heat pump for solar combisystems

This paper focuses on the study of cascade heat pump systems in combination with solar thermal for the production of hot water and space heating in single family houses with relatively high heating demand. The system concept was developed by Ratiotherm GmbH and simulated with TRNSYS 17. The basic cascade system uses the heat pump and solar collectors in parallel operation while a further development is the inclusion of an intermediate store that enables the possibility of serial/parallel operation and the use of low temperature solar heat. Parametric studies in terms of compressor size, refrigerant pair and size of intermediate heat exchanger were carried out for the optimization of the basic system. The system configurations were simulated for the complete year and compared to a reference of a solar thermal system combined with an air source heat pump. The results show ~13% savings in electricity use for all three cascade systems compared to the reference. However, the complexity of the systems is different and thus higher capital costs are expected.

Influence of hydraulics and control of thermal storage in solar assisted heat pump combisystems

This paper studies the influence of hydraulics and control of thermal storage in systems combined with solar thermal and heat pump for the production of warm water and space heating in dwellings. A reference air source heat pump system with flat plate collectors connected to a combistore was defined and modeled together with the IEA SHC Task 44 / HPP Annex 38 (T44A38) “Solar and Heat Pump Systems” boundary conditions of Strasbourg climate and SFH45 building. Three and four pipe connections as well as use of internal and external heat exchangers for DHW preparation were investigated as well as sensor height for charging of the DHW zone in the store. The temperature in this zone was varied to ensure the same DHW comfort was achieved in all cases. The results show that the four pipe connection results in 9% improvement in SPF compared to three pipe and that the external heat exchanger for DHW preparation leads to a 2% improvement compared to the reference case. Additionally the sensor height for charging the DHW zone of the store should not be too low, otherwise system performance is adversely affected

Evaluation of a thermally driven heat pump for solar heating and cooling applications

Exploiting solar energy technology for both heating and cooling purposes has the potential of meeting an appreciable portion of the energy demand in buildings throughout the year. By developing an integrated, multi-purpose solar energy system, that can operate all twelve months of the year, a high utilisation factor can be achieved which translates to more economical systems. However, there are still some techno-economic barriers to the general commercialisation and market penetration of such technologies. These are associated with high system and installation costs, significant system complexity, and lack of knowledge of system implementation and expected performance. A sorption heat pump module that can be integrated directly into a solar thermal collector has thus been developed in order to tackle the aforementioned market barriers. This has been designed for the development of cost-effective pre-engineered solar energy system kits that can provide both heating and cooling. This thesis summarises the characterisation studies of the operation of individual sorption modules, sorption module integrated solar collectors and a full solar heating and cooling system employing sorption module integrated collectors. Key performance indicators for the individual sorption modules showed cooling delivery for 6 hours at an average power of 40 W and a temperature lift of 21°C. Upon integration of the sorption modules into a solar collector, measured solar radiation energy to cooling energy conversion efficiencies (solar cooling COP) were between 0.10 and 0.25 with average cooling powers between 90 and 200 W/m2 collector aperture area. Further investigations of the sorption module integrated collectors implementation in a full solar heating and cooling system yielded electrical cooling COP ranging from 1.7 to 12.6 with an average of 10.6 for the test period. Additionally, simulations were performed to determine system energy and cost saving potential for various system sizes over a full year of operation for a 140 m2 single-family dwelling located in Madrid, Spain. Simulations yielded an annual solar fraction of 42% and potential cost savings of €386 per annum for a solar heating and cooling installation employing 20m2 of sorption integrated collectors.

Mathematical optimisation techniques applied to power system operation and planning

Nowadays, power system operation becomes more complex because of the critical operating conditions resulting from the requirements of a market-driven operation. In this context, efficient methods for optimisation of power system operation and planning become critical to satisfy the operational (technical), financial and economic demands. Therefore, the detailed analysis of modern optimisation techniques as well as their application to the power system problems represent a relevant issue from the scientific and technological points of view. This paper presents a brief overview of the developments on modern mathematical optimisation methods applied to power system operation and planning. Copyright © 2007 Inderscience Enterprises Ltd.

Simulação numérica de escoamentos gás-sólido em leito fluidizado borbulhante utilizando a teoria cinética dos escoamentos granulares

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeitos numéricos na simulação de escoamentos gás-sólido em leito fuidizado borbulhante utilizando a teoria cinética dos escoamentos granulares

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Applications and Potentials for Biogenic Methane Recovery Operations in Nebraska Agriculture, Industry, and Economic Development

ABSTRACT: This thesis report illustrates the applications and potentials of biogenic methane recovery in Nebraska’s agricultural and industrial sectors and as a means for increasing sustainable economic development in the state’s rural communities. As the nation moves toward a new green economy, biogenic methane recovery as a waste management strategy and renewable energy resource presents significant opportunities for Nebraska to be a national and world leader in agricultural and industrial innovation, advanced research and development of renewable energy technology, and generation of new product markets. Nebraska’s agricultural economy provides a distinct advantage to the state for supporting methane recovery operations that provide long-term economic and environmental partnerships among producers, industry, and communities. These opportunities will serve to protect Nebraska’s agricultural producers from volatile energy input markets and as well as creating new markets for Nebraska agricultural products. They will also serve to provide quality education and employment opportunities for Nebraska students and businesses. There are challenges and issues that remain for the state in order to take advantage of its resource potential. There is a need to produce a comprehensive Nebraska biogenic methane potential study and digital mapping system to identify high-potential producers, co-products, and markets. There is also a need to develop a web-based format of consolidated information specific to Nebraska to aid in connecting producers, service providers, educators, and policy-makers.

Making the case for grid-connected photovoltaics in Brazil

In the developed world, grid-connected photovoltaics (PVs) are the fastest-growing segment of the energy market. From 1999 to 2009, this industry had a 42% compound annual growth-rate. From 2009 to 2013, it is expected to grow to 45%, and in 2013 the achievement of grid parity - when the cost of solar electricity becomes competitive with conventional retail (including taxes and charges) grid-supplied electricity - is expected in many places worldwide. Grid-connected PV is usually perceived as an energy technology for developed countries, whereas isolated, stand-alone PV is considered as more suited for applications in developing nations, where so many individuals still lack access to electricity. This rationale is based on the still high costs of PV when compared with conventional electricity. We make the case for grid-connected PV generation in Brazil, showing that with the declining costs of PV and the rising prices of conventional electricity, urban populations in Brazil will also enjoy grid parity in the present decade. We argue that governments in developing nations should act promptly and establish the mandates and necessary conditions for their energy industry to accumulate experience in grid-connected PV, and make the most of this benign technology in the near future. (C) 2010 Elsevier Ltd. All rights reserved.

Charge separation and recombination in novel polymeric absorber materials for organic solar cells : a photophysical study

In dieser Dissertation wird die Ladungsträgergeneration und -rekombination in neuen polymeren Absorbermaterialien für organische Solarzellen untersucht. Das Verständnis dieser Prozesse ist wesentlich für die Entwicklung neuer photoaktiver Materialsysteme, die hohe Effizienzen erzielen und organische Solarzellen konkurrenzfähig im Bereich der erneuerbaren Energien machen. Experimentell verwendet diese Arbeit hauptsächlich die Methode der transienten Absorptionsspektroskopie, die sich für die Untersuchung photophysikalischer Prozesse auf einer Zeitskala von 100 fs bis 1 ms als sehr leistungsfähig erweist. Des Weiteren wird eine soft-modeling Methode vorgestellt, die es ermöglicht, photophysikalische Prozesse aus einer gemessenen transienten Absorptions-Datenmatrix zu bestimmen, wenn wenig a priori Kenntnisse der Reaktionskinetiken vorhanden sind. Drei unterschiedliche Donor:Akzeptor-Systeme werden untersucht; jedes dieser Systeme stellt eine andere Herangehensweise zur Optimierung der Materialien dar in Bezug auf Lichtabsorption über einen breiten Wellenlängenbereich, effiziente Ladungstrennung und schnellen Ladungstransport. Zuerst wird ein Terpolymer untersucht, das aus unterschiedlichen Einheiten für die Lichtabsorption und den Ladungstransport besteht. Es wird gezeigt, dass es möglich ist, den Fluss angeregter Zustände vom Chromophor auf die Transporteinheit zu leiten. Im zweiten Teil wird der Einfluss von Kristallinität auf die freie Ladungsträgergeneration mit einer Folge von ternären Mischungen, die unterschiedliche Anteile an amorphem und semi-kristallinem Polymer enthalten, untersucht. Dabei zeigt es sich, dass mit steigendem amorphen Polymeranteil sowohl der Anteil der geminalen Ladungsträgerrekombination erhöht als auch die nicht-geminale Rekombination schneller ist. Schlussendlich wird ein System untersucht, in dem sowohl Donor als auch Akzeptor Polymere sind, was zu verbesserten Absorptionseigenschaften führt. Die Rekombination von Ladungstransferzuständen auf der unter 100 ps Zeitskala stellt hier den hauptsächliche Verlustkanal dar, da freie Ladungsträger nur an Grenzflächen erzeugt werden können, an denen Donor und Akzeptor face-to-face zueinander orientiert sind. Darüber hinaus wird festgestellt, dass weitere 40-50% der Ladungsträger durch die Rekombination von Grenzflächenzuständen verloren gehen, die aus mobilen Ladungsträgern geminal gebildet werden.

The Effect of Various Electrode Microstructure Parameters on the Effective Conductivity and Three-Phase Boundary Density of Infiltrated SOFC Electrodes

Solid oxide fuel cell (SOFC) technology has the potential to be a significant player in our future energy technology repertoire based on its ability to convert chemical energy into electrical energy. Infiltrated SOFCs, in particular, have demonstrated improved performance and at lower cost than traditional SOFCs. An infiltrated electrode comprises porous ceramic scaffolding (typically constructed from the oxygen ion conducting material) that is infiltrated with electron conducting and catalytic particles. Two important SOFC electrode properties are effective conductivity and three phase boundary density (TPB). Researchers study these electrode properties separately, and fail to recognize them as competing properties. This thesis aims to (1) develop a method to model the TPB density and use it to determine the effect of porosity, scaffolding particle size, and pore former size on TPB density as well as to (2) compare the effect of porosity, scaffolding particle size, and pore former size on TPB density and effective conductivity to determine a desired set of parameters for infiltrated SOFC electrode performance. A computational model was used to study the effect of microstructure parameters on the effective conductivity and TPB density of the infiltrated SOFC electrode. From this study, effective conductivity and TPB density are determined to be competing properties of SOFC electrodes. Increased porosity, scaffolding particle size, and pore former particle size increase the effective conductivity for a given infiltrate loading above percolation threshold. Increased scaffolding particle size and pore former size ratio, however, decreases the TPB density. The maximum TPB density is achievable between porosities of 45% and 60%. The effect of microstructure parameters are more prominent at low loading with scaffolding particle size being the most significant factor and pore former size ratio being the least significant factor.

Static and dynamic contact angle measurement on rough surfaces using sessile drop profile analysis with application to water management in low temperature fuel cells

Fuel Cells are a promising alternative energy technology. One of the biggest problems that exists in fuel cell is that of water management. A better understanding of wettability characteristics in the fuel cells is needed to alleviate the problem of water management. Contact angle data on gas diffusion layers (GDL) of the fuel cells can be used to characterize the wettability of GDL in fuel cells. A contact angle measurement program has been developed to measure the contact angle of sessile drops from drop images. Digitization of drop images induces pixel errors in the contact angle measurement process. The resulting uncertainty in contact angle measurement has been analyzed. An experimental apparatus has been developed for contact angle measurements at different temperature, with the feature to measure advancing and receding contact angles on gas diffusion layers of fuel cells.

Viabilidad técnica para la explotación y separación isotópica de Li y prospectiva en el mercado de baterías de ION-7Li y de 6Li como material base de diseño en reactores de fusión nuclear

En claro alineamiento con estrategias de sostenibilidad en el uso de recursos naturales en un escenario constante de aumento de la demanda energética mundial, el desarrollo de la tecnología energética en la Historia de la Especie Humana muestra un vector de evolución permanente desde su origen en el sentido del desarrollo y uso de nuevas fuentes energéticas con la explotación de recursos naturales de manera más eficiente: soluciones energéticas con aumento de la densidad energética (exoenergía de proceso por unidad de masa de recurso natural). Así el cambio de escala en la demanda de explotación del Litio como recurso natural se viene presentando en la última década ligada al desarrollo del mercado de las baterías "ion-Litio" y los requisitos de combustible (Deuterio y Litio) en el camino de la fusión nuclear como opción energética próxima. El análisis anticipado de las demandas sinérgicas a escala de ambos mercados aparece de enorme interés prospectivo en sus aspectos técnicos: (1) tecnologías de base para la extracción mineral y de agua marina y (2) su enriquecimiento isotópico (de interés sinérgico; 7Li para baterías eficientes ion-litio; 6Li como regenerador de tritio en ciclo de combustible en fusión nuclear) a la vez que en sus aspectos económicos. Este Proyecto realiza: (1) un ejercicio de análisis prospectivo de la demanda y de mercado para el enriquecimiento 6Li/7Li para las próximas décadas, (2) se califican los desarrollos tecnológicos específicos que van a poder permitir la producción a escala conforme a la demanda; (3) se selecciona y califica una técnica [de centrifugación / termo-difusión/ destilación combinada] como opción tecnológicamente viable para la producción a escala de formas litiadas; (4) se propone un diseño conceptual de planta de producción y finalmente (5) propone un estudio de viabilidad para la demostración de proceso y construcción de dicha planta de demostración de la nueva capacidad tecnológica. ABSTRACT Clearly aligned with sustainability strategies under growing world energy demand in the use of natural resources the development of energy technology in the history of the human species shows a vector of ongoing evolution from its origin in the sense of the development and use of new energy sources with the exploitation of natural resources in a more efficient manner. The change of scale in the demand for exploitation of Lithium as a natural resource appears during the last decade as bound to the deployment of "lithium-ion" batteries market and to the Nuclear Fusion fuels (deuterium and lithium) supply scaled demands. The prospective analysis of demands to scale in both markets appears in scene with huge prospective interest in its technical aspects: (1) base technologies for mineral and water marine extraction (2) its isotopic enrichment (synergistic interests; 7Li efficient battery Li-ion; 6Li as fusion nuclear fuel breeder (tritium) as well as in its economic aspects. This Project: (1) propose a prospective analysis exercise of the synergistic supply demand for coming decades for the enrichment of 6Li and 7Li, (2) qualifies specific technological developments ongoing to respond to supply demand; (3) select and qualifies an appropriate technique [combined centrifugation/thermo-diffusion/distillation] as technologically viable option for lithiated forms scaled-production; (4) proposes a conceptual design of production plant based on the technique and finally (5) proposes a feasibility study for the process demonstration and construction of this new technological capability Demonstration Plant.

The Global Carbon Pricing Policy Solution to Climate Change

While the topic of climate change is controversial, the world needs to take a precautionary approach to reduce carbon dioxide emissions. With growing populations and increasing energy demands, solutions to cleaner energy need to be developed and implemented. In order to successfully reduce carbon dioxide emissions, a global carbon pricing policy needs to be developed that includes all countries and allows each region to utilize the best clean energy technology options along with economic incentives that will be the most effective. The research conducted in this project validates the hypothesis that placing a monetary price on carbon will allow natural, technological, and financial resources to come together to implement a feasible energy solution that will reduce global carbon dioxide emissions.

Bibliography of aquatic ecosystems effects, analytical methods and treatment technologies for organic compounds in advanced fossil-fuel processing effluents /

Mode of access: Internet.