Preparação de resinas de poliuretana à base de óleo de mamona e dietanolamina

The aim of this work was the preparation of polyols from reactions between castor oil and dietanolamine to increase the hydroxyl content and the network degree in the products to application in electronic devices. The polyols and the mixtures obtained were characterized by nuclear magnetic ressonance. Castor oil (CO) is a natural triglyceride - based polyol possessing hydroxyl groups, which allow several reactions that produce many different products. Among them are the polyurethanes (PU), which have been considered an ideal product for the covering of electricelectronic circuits, due to their excellent electrical, shock-absorbing, solvents resistance and hydrolytic stability properties. About 90% of the fatty acids present in the castor oil are ricinoleic acid (12-hydroxyoleic acid), while the remaining 10% correspond to non-hydroxylated fatty acids, mainly linoleic and oleic acids. The chemical analysis of castor oil indicates a hydroxyl number of 2.7. In this work, a polyol was obtained by the reaction of the CO with diethanolamine (DEA), in order to elevate the hydroxyl value from 160 to 230 or to 280 mgKOH/g, and characterized by nuclear magnetic resonance (NMR) 1H and 13C (Mercury 200). The polyadition of the resulting polyol with isophorone diisocianate (IPDI) was carried out at 60°C, and the reaction kinetics was followed by rheological measurements in a Haake RS150 rheometer. The electrical properties were determined in a HP LCR Meter 4262A, at 1.0 Hz and 10.0 KHz. The chemical analysis showed that the polyols obtained presented hydroxyl number from 230 to 280 mgKOH/g. The polyadition reaction with IPDI produced polyurethane resins with the following properties: hardness in the range from 45 shore A to 65 shore D (ASTM D2240); a dielectric constant of 3.0, at 25°C (ASTM D150). Those results indicate that the obtained resins present compatible properties to the similar products of fossil origin, which are used nowadays for covering electric-electronic circuits. Therefore, the PUs from castor oil can be considered as alternative materials of renewable source, free from the highly harmful petroleum - derived solvents

The CMS experiment at the CERN LHC

The Compact Muon Solenoid (CMS) detector is described. The detector operates at the Large Hadron Collider (LHC) at CERN. It was conceived to study proton-proton (and lead-lead) collisions at a centre-of-mass energy of 14 TeV (5.5 TeV nucleon-nucleon) and at luminosities up to 10(34)cm(-2)s(-1) (10(27)cm(-2)s(-1)). At the core of the CMS detector sits a high-magnetic-field and large-bore superconducting solenoid surrounding an all-silicon pixel and strip tracker, a lead-tungstate scintillating-crystals electromagnetic calorimeter, and a brass-scintillator sampling hadron calorimeter. The iron yoke of the flux-return is instrumented with four stations of muon detectors covering most of the 4 pi solid angle. Forward sampling calorimeters extend the pseudo-rapidity coverage to high values (vertical bar eta vertical bar <= 5) assuring very good hermeticity. The overall dimensions of the CMS detector are a length of 21.6 m, a diameter of 14.6 m and a total weight of 12500 t.

A unity power factor multiple isolated outputs switching mode power supply using a single switch

The authors present an offline switching power supply with multiple isolated outputs and unity power factor with the use of only one power processing stage, based on the DC-DC SEPIC (single ended primary inductance converter) modulated by variable hysteresis current control. The principle of operation, the theoretical analysis, the design procedure, an example, and simulation results are presented. A laboratory prototype, rated at 160 W, operating at a maximum switching frequency of 100 kHz, with isolated outputs rated at +5 V/15 A -5 V/1 A, +12 V/6 A and -12 V/1 A, has been built given an input power factor near unity.

Sistema de extração de potência (power harvesting) usando transdutores piezelétricos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Ambiente computacional para projetos de sistemas com tecnologia mista

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Eletroestimulador funcional de oito canais com malha de realimentação utilizando Controlador Digital

Pós-graduação em Engenharia Elétrica - FEIS

Sensor em fibra óptica aplicado à caracterização de atuadores piezoelétricos flextensionais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de um circuito eletrônico experimental de anemômetro de fio quente

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Utilização de materiais piezelétricos (PZTS) para coleta e armazenamento de energia

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Reciclagem de isolantes térmicos presentes em defletores de calor automotivo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Equipamento eletromagnético para prospecção geofísica e modelamento reduzido

Nas últimas décadas, a prospecção por métodos eletromagnéticos vem-se constituindo numa técnica eficiente para prospecção mineral. O objetivo deste trabalho foi desenvolver um equipamento para prospecção eletromagnética quantitativa de corpos condutores, através do método dipolo-dipolo, podendo ainda ser usado em modelos reduzidos. Eletricamente, o sistema mede grandezas relacionadas ao acoplamento indutivo entre duas bobinas: transmissora e receptora. Elas são dispostas na superfície da terra, afastadas entre si, e a terra, desse modo, constitui o núcleo acoplador. Quando existem corpos condutores nas proximidades, estes são denunciados por alterações no comportamento do sinal induzido na bobina receptora. O equipamento compreende dois conjuntos: o transmissor e o receptor, além de acessórios. O transmissor gera um campo eletromagnético nas freqüências de 520 e 3.090 Hz, e um sinal de referência para o receptor, o qual é enviado através de um cabo. O receptor, inicialmente, separa o sinal induzido pelos campos secundários gerados por condutores, do campo normalmente recebido, quando a condutividade da subsuperfície é relativamente uniforme (campo primário). Em seguida, decompõe esse sinal em duas componentes ortogonais, uma em fase, e outra em quadratura com o campo primário. Através de duas escalas de precisão, as amplitudes dessas componentes são mostradas como percentagens do campo primário, com precisão de 1%. A sensibilidade do receptor é de 0,5 μV. O circuito eletrônico foi rigorosamente testado com preciso instrumental de laboratório. Em seguida, testou-se sua aplicação no Laboratório de Modelo Reduzido Eletromagnético do NCGG, refazendo-se experiências clássicas, encontradas na literatura especializada. No campo, foi experimentado próximo da cidade de Araci no Estado da Bahia, em áreas prospectadas pela "Rio Doce Geologia e Mineração S/A-DOCEGEO". Em ambos os casos, verificaram-se bons resultados.

Desenvolvimento de um computador de bordo para veículo Baja-SAE

The objective of this paper is show the development of an Eletronic Control Unit (ECU) for Baja-SAE vehicles from its requirements to final implementation. An ECU for Baja-SAE vehicles is made of electric and electronic circuits (appropriated to the hostile situations of an off-road competition) able to make important measurements for the running or stand-by vehicle performance. For this development, some concepts were studied: embedded electronics concepts (mainly microcontrollers and data acquisition circuits) and sensoring. Both the studies were made considering the off-road environment. After these initial studies, the elaboration of the basics hardware and software (under simulations) has begun, and this elaboration objectives maximum performance and low implementation cost. After the theorical studies, basic definition of the hardware and software’s architectures and simulations, the printed circuit boards (PCB) were made, as exhaustive tests in these boards for debugging and verify if the boards work well. Once the system was tested in the university, it ran into a regional Southeast competition in 2010, that definitely proved the efficiency of the whole system

Caracterização in vitro de técnica biomagnética empregando magnetômetros 3D para avaliar tempo de trânsito esofagiano

The biomagnetic techniques use different magnetic field detectors to measure parameters of the human physiology. Those techniques present the advantage of being noninvasive and radiation free. Among them we can show up the Superconducting Quantum Interference Device (SQUID), the Current Alternate Biosusceptometry (ACB) and, more recently, the employment of anisotropic magnetoresistive sensors. Those magnetic sensors have a low cost and good sensitivity to measure different physiological parameters using magnetic markers. The biomagnetic techniques have being used successfully through study on the characteristics of the gastrointestinal tract. Recent research, the magnetoresistors were used to evaluate the transit time and localization of magnetic sources in different parts of the gastrointestinal tract. The objective of this work is the characterization, with in vitro tests, of a biomagnetic instrumentation using two 3-axis magnetoresistors arranged in a gradiometric coplanar setup to evaluate esophageal transit time, analyze and compare the results of experimental signals and the magnetic theory, as well as evaluate the instrumentation gain with use of tri-axial sensor front to the mono-axial sensor. The instrumentation is composed by two three-axis sensing magnetometers, precision power supply and amplifier electronic circuits. The sensors fixed in a coplanar setup were separate by distance of 18 cm. The sensitivity tests had been carried through using a cylindrical magnet (ø = 4 mm and h = 4 mm) of neodymium-iron-boron (grid 35). The tests were done moving the permanent magnet on the sensors parallel axis, simulating the food transit in... (Complete abstract click electronic access below)

Metodologia de simulação numérica do comportamento térmico em equipamentos eletroeletrônicos

Pós-graduação em Engenharia Elétrica - FEIS

Proposta de equipamento de conexão à rede para a utilização da geração de energia solar em consumidores de pequeno e médio porte

Pós-graduação em Engenharia Mecânica - FEG