Comparison of ultrafine particle release from hardcopy devices in emission test chambers and office rooms

The release of ultrafine particles (UFP) from laser printers and office equipment was analyzed using a particle counter (FMPS; Fast Mobility Particle Sizer) with a high time resolution, as well as the appropriate mathematical models. Measurements were carried out in a 1 m³ chamber, a 24 m³ chamber and an office. The time-dependent emission rates were calculated for these environments using a deconvolution model, after which the total amount of emitted particles was calculated. The total amounts of released particles were found to be independent of the environmental parameters and therefore, in principle, they were appropriate for the comparison of different printers. On the basis of the time-dependent emission rates, “initial burst” emitters and constant emitters could also be distinguished. In the case of an “initial burst” emitter, the comparison to other devices is generally affected by strong variations between individual measurements. When conducting exposure assessments for UFP in an office, the spatial distribution of the particles also had to be considered. In this work, the spatial distribution was predicted on a case by case basis, using CFD simulation.

Comparison of emission rate values for odour and odorous chemicals derived from two sampling devices

Field and laboratory measurements identified a complex relationship between odour emission rates provided by the US EPA dynamic emission chamber and the University of New South Wales wind tunnel. Using a range of model compounds in an aqueous odour source, we demonstrate that emission rates derived from the wind tunnel and flux chamber are a function of the solubility of the materials being emitted, the concentrations of the materials within the liquid; and the aerodynamic conditions within the device – either velocity in the wind tunnel, or flushing rate for the flux chamber. The ratio of wind tunnel to flux chamber odour emission rates (OU m-2 s) ranged from about 60:1 to 112:1. The emission rates of the model odorants varied from about 40:1 to over 600:1. These results may provide, for the first time, a basis for the development of a model allowing an odour emission rate derived from either device to be used for odour dispersion modelling.

Work at hand : an exploration of gesture in the context of work and everyday life to inform the design of gestural input devices

This research explores gestures used in the context of activities in the workplace and in everyday life in order to understand requirements and devise concepts for the design of gestural information applicances. A collaborative method of video interaction analysis devised to suit design explorations, the Video Card Game, was used to capture and analyse how gesture is used in the context of six different domains: the dentist's office; PDA and mobile phone use; the experimental biologist's laboratory; a city ferry service; a video cassette player repair shop; and a factory flowmeter assembly station. Findings are presented in the form of gestural themes, derived from the tradition of qualitative analysis but bearing some similarity to Alexandrian patterns. Implications for the design of gestural devices are discussed.

Adolescent protective behaviour to reduce drug and alcohol use, alcohol-related harm and interpersonal violence

Typically adolescents' friends are considered a risk factor for adolescent engagement in risk-taking. This study took a more novel approach, by examining adolescent friendship as a protective factor. In particular it investigated friends' potential to intervene to reduce risk-taking. 540 adolescents (mean age 13.47 years) were asked about their intention to intervene to reduce friends' alcohol, drug and alcohol-related harms and about psychosocial factors potentially associated with intervening. More than half indicated that they would intervene in friends' alcohol, drug use, alcohol-related harms and interpersonal violence. Intervening was associated with being female, having friends engage in overall less risk-taking and having greater school connectedness. The findings provide an important understanding of increasing adolescent protective behavior as a potential strategy to reduce alcohol and drug related harms.

Biomechanical force displacement analysis of strength of fixation of tracker holding devices to bone in computer aided joint replacement

Computer aided joint replacement surgery has become very popular during recent years and is being done in increasing numbers all over the world. The accuracy of the system depends to a major extent, on accurate registration and immobility of the tracker attachment devices to the bone. This study was designed to asses the forces needed to displace the tracker attachment devices in the bone simulators. Bone simulators were used to maintain the uniformity of the bone structure during the study. The fixation devices tested were 3mm diameter self drilling, self tapping threaded pin, 4mm diameter self tapping cortical threaded pin, 5mm diameter self tapping cancellous threaded pin and a triplanar fixation device ‘ortholock’ used with three 3mm pins. All the devices were tested for pull out, translational and rotational forces in unicortical and bicortical fixation modes. Also tested was the normal bang strength and forces generated by leaning on the devices. The forces required to produce translation increased with the increasing diameter of the pins. These were 105N, 185N, and 225N for the unicortical fixations and 130N, 200N, 225N for the bicortical fixations for 3mm, 4mm and 5mm diameter pins respectively. The forces required to pull out the pins were 1475N, 1650N, 2050N for the unicortical, 1020N, 3044N and 3042N for the bicortical fixated 3mm, 4mm and 5mm diameter pins. The ortholock translational and pull out strength was tested to 900N and 920N respectively and still it did not fail. Rotatory forces required to displace the tracker on pins was to the magnitude of 30N before failure. The ortholock device had rotational forces applied up to 135N and still did not fail. The manual leaning forces and the sudden bang forces generated were of the magnitude of 210N and 150N respectively. The strength of the fixation pins increases with increasing diameter from three to five mm for the translational forces. There is no significant difference in pull out forces of four mm and five mm diameter pins though it is more that the three mm diameter pins. This is because of the failure of material at that stage rather than the fixation device. The rotatory forces required to displace the tracker are very small and much less that that can be produced by the surgeon or assistants in single pins. Although the ortholock device was tested to 135N in rotation without failing, one has to be very careful not to put any forces during the operation on the tracker devices to ensure the accuracy of the procedure.

Motorcycle rider protective apparel wearing : observational study results from the Brisbane and Canberra regions

The continued growth in popularity of motorcycling is an area of concern within the road safety domain due to the vulnerability of motorcyclists sustaining injury in the event of a crash. Currently in Australia only motorcycle helmets are mandatory for motorcyclists or pillions to wear and there is no legislative standard for other protective apparel. This paper reports the results obtained from a series of motorcyclists’ apparel observational studies undertaken in the Brisbane and Canberra regions. The sites selected for the research were designed to enable the observation of both recreational and commuter riders. The results highlight both similarities and differences in the type of protective apparel worn by motorcyclists and pillions observed across the two regions. Encouragingly, across all the sites the majority of riders were wearing protective apparel on their upper body. However, a lower proportion of riders were observed wearing protective apparel on their lower body, particularly at the commuter sites in Brisbane. Similarly, the wearing of full face helmets was very high, except at the commuter sites in Brisbane. The generally lower use of protective apparel among commuter riders in Brisbane would appear to reflect both situational factors, such as climate, and the higher proportion of scooters observed at the sites. The implications of these results are discussed and recommendations are made for future research to identify factors that influence the wearing of protective motorcycle apparel.