Development of a triple stage heat transformer for the recycling of low temperature heat energy

Absorption heat transformers are thermodynamic systems which are capable of recycling industrial waste heat energy by increasing its temperature. Triple stage heat transformers (TAHTs) can increase the temperature of this waste heat by up to approximately 145˚C. The principle factors influencing the thermodynamic performance of a TAHT and general points of operating optima were identified using a multivariate statistical analysis, prior to using heat exchange network modelling techniques to dissect the design of the TAHT and systematically reassemble it in order to minimise internal exergy destruction within the unit. This enabled first and second law efficiency improvements of up to 18.8% and 31.5% respectively to be achieved compared to conventional TAHT designs. The economic feasibility of such a thermodynamically optimised cycle was investigated by applying it to an oil refinery in Ireland, demonstrating that in general the capital cost of a TAHT makes it difficult to achieve acceptable rates of return. Decreasing the TAHT's capital cost may be achieved by redesigning its individual pieces of equipment and reducing their size. The potential benefits of using a bubble column absorber were therefore investigated in this thesis. An experimental bubble column was constructed and used to track the collapse of steam bubbles being absorbed into a hotter lithium bromide salt solution. Extremely high mass transfer coefficients of approximately 0.0012m/s were observed, showing significant improvements over previously investigated absorbers. Two separate models were developed, namely a combined heat and mass transfer model describing the rate of collapse of the bubbles, and a stochastic model describing the hydrodynamic motion of the collapsing vapour bubbles taking into consideration random fluctuations observed in the experimental data. Both models showed good agreement with the collected data, and demonstrated that the difference between the solution's temperature and its boiling temperature is the primary factor influencing the absorber's performance.

Energy Dependence of Gold Nanoparticle Radiosensitization in Plasmid DNA

Gold nanoparticles (GNPs) are of considerable interest for use as a radiosensitizer, because of their biocompatibility and their ability to increase dose deposited because of their high mass energy absorption coefficient. Their sensitizing properties have been verified experimentally, but a discrepancy between the experimental results and theoretical predictions suggests that the sensitizing effect does not depend solely on gold's superior absorption of energetic photons. This work presents the results of three sets of experiments that independently mapped out the energy dependence of the radiosensitizing effects of GNPs on plasmid DNA suspended in water. Incident photon energy was varied from 11.8 to 80 keV through the use of monochromatic synchrotron and broadband X-rays. These results depart significantly from the theoretical predictions in two ways: First, the sensitization is significantly larger than would be predicted; second, it does not vary with energy as would be predicted from energy absorption coefficients. These results clearly demonstrate that the effects of GNP-enhanced therapies cannot be predicted by considering additional dose alone and that a greater understanding of the processes involved is necessary for the development of future therapeutics.

Blast-wave absorption capacity of sandwich structures incorporating cellular materials

A incorporação de materiais absorsores de energia (AE) em sistemas de protecção é uma clara possibilidade de melhoraria do seu desempenho, devido à elevada relação entre a sua resistência e o seu peso, e a excelente capacidade para absorverem energia quando solicitados dinamicamente. As propriedades mecânicas da cortiça (e.g. a baixa densidade e a elevada rigidez e resistência específicas) sugerem que este material — assim como os seus derivados — podem apresentar propriedades excelentes quando aplicados como núcleos em sistemas AE do tipo estrutura sanduíche. Esta dissertação engloba trabalho experimental e numérico. O primeiro conjunto de testes experimentais consistiu na caracterização experimental dinâmica (ondas de choque de explosivos) do comportamento de dois micra aglomerados de cortiça (MAC), NL20 e TB40. Um pendulo balístico de 4 cabos foi usado para a medição do impulso transmitido a uma amostra de MAC impactada por uma onda de choque com origem na detonação de um explosivo energético. Foi registado o movimento do pêndulo e os valores de força resultantes. Um modelo numérico do problema recorrendo ao método dos elementos finitos (MEF) foi também desenvolvido, apresentando uma elevada correlação com a análise experimental, permitindo assim o desenvolvimento de um modelo constitutivo adequado à modelação do comportamento dinâmico dos MAC neste tipo de solicitações. Na segunda fase de testes experimentais, os MAC testados anteriormente são incorporados como núcleos em estruturas sanduíche com faces de alumínio (liga 5754-H22). Foram medidos os valores de defleção e o impulso transmitido ao pêndulo através do movimento oscilatório. São determinados os efeitos da densidade e da espessura dos núcleos na resposta estrutural do sistema. Também neste caso foi desenvolvido um modelo recorrendo ao MEF e posteriormente validado com resultados experimentais.

Assessment of expected damage on buildings subjected to Lorca earthquake through an energy-based seismic index method and nonlinear dynamic response analyses

The city of Lorca (Spain) was hit on May 11th, 2011, by two consecutive earth-quakes of magnitudes 4.6 and 5.2 Mw, causing casualties and important damage in buildings. Many of the damaged structures were reinforced concrete frames with wide beams. This study quantifies the expected level of damage on this structural type in the case of the Lorca earth-quake by means of a seismic index Iv that compares the energy input by the earthquake with the energy absorption/dissipation capacity of the structure. The prototype frames investigated represent structures designed in two time periods (1994–2002 and 2003–2008), in which the applicable codes were different. The influence of the masonry infill walls and the proneness of the frames to concentrate damage in a given story were further investigated through nonlinear dynamic response analyses. It is found that (1) the seismic index method predicts levels of damage that range from moderate/severe to complete collapse; this prediction is consistent with the observed damage; (2) the presence of masonry infill walls makes the structure very prone to damage concentration and reduces the overall seismic capacity of the building; and (3) a proper hierarchy of strength between beams and columns that guarantees the formation of a strong column-weak beam mechanism (as prescribed by seismic codes), as well as the adoption of counter-measures to avoid the negative interaction between non-structural infill walls and the main frame, would have reduced the level of damage from Iv=1 (collapse) to about Iv=0.5 (moderate/severe damage)

Experimental evaluation of a portable energy absorbing system for highway service vehicles. Final report for phase II.

Connecticut Department of Transportation, Bureau of Planning and Research, Wethersfield

Identification of superior energy-absorbing materials for school bus interiors: Volume I - summary report. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Identification of superior energy-absorbing materials for school bus interiors: Volume II - technical report. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Identification of superior energy-absorbing materials for school bus interiors: Volume III - appendices report. Final report.

National Highway Traffic Safety Administration, Washington, D.C.

Experimental evaluation of a portable energy absorbing system for highway service vehicles. Final report for phase I.

Connecticut Department of Transportation, Bureau of Planning and Research, Wethersfield

Analysis of stirred mill performance using DEM simulation: Part 1 - Media motion, energy consumption and collisional environment

Stirred mills are becoming increasingly used for fine and ultra-fine grinding. This technology is still poorly understood when used in the mineral processing context. This makes process optimisation of such devices problematic. 3D DEM simulations of the flow of grinding media in pilot scale tower mills and pin mills are carried out in order to investigate the relative performance of these stirred mills. Media flow patterns and energy absorption rates and distributions are analysed here. In the second part of this paper, coherent flow structures, equipment wear and mixing and transport efficiency are analysed. (C) 2006 Published by Elsevier Ltd.

Conceptual Design of a Circulating Fluidized Bed Reactor as a Thermochemical Thermal Energy Storage System for Applications in Concentrated Solar Thermal Power Plants

Thesis (Master's)--University of Washington, 2016-08

Testing and simulation of extruded polystyrene foam at low to moderate strain rates

This paper presents a study into the behaviour of extruded polystyrene foam at low strain rates. The foam is being studied in order assess its potential for use as part of a new innovative design of portable road safety barrier the aim to consume less water and reduce rates of serious injury. The foam was tested at a range of low strain rates, with the stress and strain behaviour of the foam specimens being recorded. The energy absorption capabilities of the foam were assessed as well as the response of the foam to multiple loadings. The experimental data was then used to create a material model of the foam for use in the explicit finite element solver LS-DYNA. Simulations were carried out using the material model which showed excellent correlation between the numerical material model and the experimental data.