Algorithms for autonomous tandem operation of a dual M113 system

In mid-July 2003, the U.S. Army Tank-Automotive & Armaments Command (TACOM) performed a series of experiments at Keweenaw Research Center (KRC), with a remote operated mine roller system. This system, named Panther Lite, consists of two M113 Armored Personnel Carriers (APC’s) connected by a Tandem Vehicle Linkage Assembly (TVLA). The system has three sets of mine rollers, two of which are connected to the front of the lead vehicle with one set trailing from the trail vehicle. Currently, the system requires two joystick controllers. One regulates the braking of the tracks, throttle, and transmission of the lead vehicle and the other controls the braking and throttle of the rear vehicle. One operator controls both joysticks, attempting to maneuver the lead vehicle along a desired path. At the same time, this operator makes compensation maneuvers to reduce lateral loads in the TVLA and to guide the rear mine rollers along the desired path. The purpose of this project is to create algorithms that would allow the slave (trail) vehicle to operate using inputs that maneuver the control (lead) vehicle. The project will be completed by first reconstructing the experimental data. Kinematic models will be generated and simulations created. The models will then be correlated with the reconstructions of the experimental data. The successful completion of this project will be a first step to eliminating the need for the second joystick.

Control algorithms for large scale adaptive optics

In this dissertation, the problem of creating effective large scale Adaptive Optics (AO) systems control algorithms for the new generation of giant optical telescopes is addressed. The effectiveness of AO control algorithms is evaluated in several respects, such as computational complexity, compensation error rejection and robustness, i.e. reasonable insensitivity to the system imperfections. The results of this research are summarized as follows: 1. Robustness study of Sparse Minimum Variance Pseudo Open Loop Controller (POLC) for multi-conjugate adaptive optics (MCAO). The AO system model that accounts for various system errors has been developed and applied to check the stability and performance of the POLC algorithm, which is one of the most promising approaches for the future AO systems control. It has been shown through numerous simulations that, despite the initial assumption that the exact system knowledge is necessary for the POLC algorithm to work, it is highly robust against various system errors. 2. Predictive Kalman Filter (KF) and Minimum Variance (MV) control algorithms for MCAO. The limiting performance of the non-dynamic Minimum Variance and dynamic KF-based phase estimation algorithms for MCAO has been evaluated by doing Monte-Carlo simulations. The validity of simple near-Markov autoregressive phase dynamics model has been tested and its adequate ability to predict the turbulence phase has been demonstrated both for single- and multiconjugate AO. It has also been shown that there is no performance improvement gained from the use of the more complicated KF approach in comparison to the much simpler MV algorithm in the case of MCAO. 3. Sparse predictive Minimum Variance control algorithm for MCAO. The temporal prediction stage has been added to the non-dynamic MV control algorithm in such a way that no additional computational burden is introduced. It has been confirmed through simulations that the use of phase prediction makes it possible to significantly reduce the system sampling rate and thus overall computational complexity while both maintaining the system stable and effectively compensating for the measurement and control latencies.

Effect of high order interpolation in the stability and efficiency of the time-integration process in vorticity-velocity CFD algorithms

The numerical solution of the incompressible Navier-Stokes Equations offers an effective alternative to the experimental analysis of Fluid-Structure interaction i.e. dynamical coupling between a fluid and a solid which otherwise is very complex, time consuming and very expensive. To have a method which can accurately model these types of mechanical systems by numerical solutions becomes a great option, since these advantages are even more obvious when considering huge structures like bridges, high rise buildings, or even wind turbine blades with diameters as large as 200 meters. The modeling of such processes, however, involves complex multiphysics problems along with complex geometries. This thesis focuses on a novel vorticity-velocity formulation called the KLE to solve the incompressible Navier-stokes equations for such FSI problems. This scheme allows for the implementation of robust adaptive ODE time integration schemes and thus allows us to tackle the various multiphysics problems as separate modules. The current algorithm for KLE employs a structured or unstructured mesh for spatial discretization and it allows the use of a self-adaptive or fixed time step ODE solver while dealing with unsteady problems. This research deals with the analysis of the effects of the Courant-Friedrichs-Lewy (CFL) condition for KLE when applied to unsteady Stoke’s problem. The objective is to conduct a numerical analysis for stability and, hence, for convergence. Our results confirmthat the time step ∆t is constrained by the CFL-like condition ∆t ≤ const. hα, where h denotes the variable that represents spatial discretization.

Algorithms for spacecraft formation flying navigation based on wireless positioning system measurements

Spacecraft formation flying navigation continues to receive a great deal of interest. The research presented in this dissertation focuses on developing methods for estimating spacecraft absolute and relative positions, assuming measurements of only relative positions using wireless sensors. The implementation of the extended Kalman filter to the spacecraft formation navigation problem results in high estimation errors and instabilities in state estimation at times. This is due tp the high nonlinearities in the system dynamic model. Several approaches are attempted in this dissertation aiming at increasing the estimation stability and improving the estimation accuracy. A differential geometric filter is implemented for spacecraft positions estimation. The differential geometric filter avoids the linearization step (which is always carried out in the extended Kalman filter) through a mathematical transformation that converts the nonlinear system into a linear system. A linear estimator is designed in the linear domain, and then transformed back to the physical domain. This approach demonstrated better estimation stability for spacecraft formation positions estimation, as detailed in this dissertation. The constrained Kalman filter is also implemented for spacecraft formation flying absolute positions estimation. The orbital motion of a spacecraft is characterized by two range extrema (perigee and apogee). At the extremum, the rate of change of a spacecraft’s range vanishes. This motion constraint can be used to improve the position estimation accuracy. The application of the constrained Kalman filter at only two points in the orbit causes filter instability. Two variables are introduced into the constrained Kalman filter to maintain the stability and improve the estimation accuracy. An extended Kalman filter is implemented as a benchmark for comparison with the constrained Kalman filter. Simulation results show that the constrained Kalman filter provides better estimation accuracy as compared with the extended Kalman filter. A Weighted Measurement Fusion Kalman Filter (WMFKF) is proposed in this dissertation. In wireless localizing sensors, a measurement error is proportional to the distance of the signal travels and sensor noise. In this proposed Weighted Measurement Fusion Kalman Filter, the signal traveling time delay is not modeled; however, each measurement is weighted based on the measured signal travel distance. The obtained estimation performance is compared to the standard Kalman filter in two scenarios. The first scenario assumes using a wireless local positioning system in a GPS denied environment. The second scenario assumes the availability of both the wireless local positioning system and GPS measurements. The simulation results show that the WMFKF has similar accuracy performance as the standard Kalman Filter (KF) in the GPS denied environment. However, the WMFKF maintains the position estimation error within its expected error boundary when the WLPS detection range limit is above 30km. In addition, the WMFKF has a better accuracy and stability performance when GPS is available. Also, the computational cost analysis shows that the WMFKF has less computational cost than the standard KF, and the WMFKF has higher ellipsoid error probable percentage than the standard Measurement Fusion method. A method to determine the relative attitudes between three spacecraft is developed. The method requires four direction measurements between the three spacecraft. The simulation results and covariance analysis show that the method’s error falls within a three sigma boundary without exhibiting any singularity issues. A study of the accuracy of the proposed method with respect to the shape of the spacecraft formation is also presented.

In-situ measurement and characterization of cloud particles using digital in-line holography

Satellite measurement validations, climate models, atmospheric radiative transfer models and cloud models, all depend on accurate measurements of cloud particle size distributions, number densities, spatial distributions, and other parameters relevant to cloud microphysical processes. And many airborne instruments designed to measure size distributions and concentrations of cloud particles have large uncertainties in measuring number densities and size distributions of small ice crystals. HOLODEC (Holographic Detector for Clouds) is a new instrument that does not have many of these uncertainties and makes possible measurements that other probes have never made. The advantages of HOLODEC are inherent to the holographic method. In this dissertation, I describe HOLODEC, its in-situ measurements of cloud particles, and the results of its test flights. I present a hologram reconstruction algorithm that has a sample spacing that does not vary with reconstruction distance. This reconstruction algorithm accurately reconstructs the field to all distances inside a typical holographic measurement volume as proven by comparison with analytical solutions to the Huygens-Fresnel diffraction integral. It is fast to compute, and has diffraction limited resolution. Further, described herein is an algorithm that can find the position along the optical axis of small particles as well as large complex-shaped particles. I explain an implementation of these algorithms that is an efficient, robust, automated program that allows us to process holograms on a computer cluster in a reasonable time. I show size distributions and number densities of cloud particles, and show that they are within the uncertainty of independent measurements made with another measurement method. The feasibility of another cloud particle instrument that has advantages over new standard instruments is proven. These advantages include a unique ability to detect shattered particles using three-dimensional positions, and a sample volume size that does not vary with particle size or airspeed. It also is able to yield two-dimensional particle profiles using the same measurements.

Space trajectories optimization using variable-chromosome-length genetic algorithms

The problem of optimal design of a multi-gravity-assist space trajectories, with free number of deep space maneuvers (MGADSM) poses multi-modal cost functions. In the general form of the problem, the number of design variables is solution dependent. To handle global optimization problems where the number of design variables varies from one solution to another, two novel genetic-based techniques are introduced: hidden genes genetic algorithm (HGGA) and dynamic-size multiple population genetic algorithm (DSMPGA). In HGGA, a fixed length for the design variables is assigned for all solutions. Independent variables of each solution are divided into effective and ineffective (hidden) genes. Hidden genes are excluded in cost function evaluations. Full-length solutions undergo standard genetic operations. In DSMPGA, sub-populations of fixed size design spaces are randomly initialized. Standard genetic operations are carried out for a stage of generations. A new population is then created by reproduction from all members based on their relative fitness. The resulting sub-populations have different sizes from their initial sizes. The process repeats, leading to increasing the size of sub-populations of more fit solutions. Both techniques are applied to several MGADSM problems. They have the capability to determine the number of swing-bys, the planets to swing by, launch and arrival dates, and the number of deep space maneuvers as well as their locations, magnitudes, and directions in an optimal sense. The results show that solutions obtained using the developed tools match known solutions for complex case studies. The HGGA is also used to obtain the asteroids sequence and the mission structure in the global trajectory optimization competition (GTOC) problem. As an application of GA optimization to Earth orbits, the problem of visiting a set of ground sites within a constrained time frame is solved. The J2 perturbation and zonal coverage are considered to design repeated Sun-synchronous orbits. Finally, a new set of orbits, the repeated shadow track orbits (RSTO), is introduced. The orbit parameters are optimized such that the shadow of a spacecraft on the Earth visits the same locations periodically every desired number of days.

Application of MFBD Algorithms to Image Reconstruction Under Anisoplanatic Conditions

All optical systems that operate in or through the atmosphere suffer from turbulence induced image blur. Both military and civilian surveillance, gun-sighting, and target identification systems are interested in terrestrial imaging over very long horizontal paths, but atmospheric turbulence can blur the resulting images beyond usefulness. My dissertation explores the performance of a multi-frame-blind-deconvolution technique applied under anisoplanatic conditions for both Gaussian and Poisson noise model assumptions. The technique is evaluated for use in reconstructing images of scenes corrupted by turbulence in long horizontal-path imaging scenarios and compared to other speckle imaging techniques. Performance is evaluated via the reconstruction of a common object from three sets of simulated turbulence degraded imagery representing low, moderate and severe turbulence conditions. Each set consisted of 1000 simulated, turbulence degraded images. The MSE performance of the estimator is evaluated as a function of the number of images, and the number of Zernike polynomial terms used to characterize the point spread function. I will compare the mean-square-error (MSE) performance of speckle imaging methods and a maximum-likelihood, multi-frame blind deconvolution (MFBD) method applied to long-path horizontal imaging scenarios. Both methods are used to reconstruct a scene from simulated imagery featuring anisoplanatic turbulence induced aberrations. This comparison is performed over three sets of 1000 simulated images each for low, moderate and severe turbulence-induced image degradation. The comparison shows that speckle-imaging techniques reduce the MSE 46 percent, 42 percent and 47 percent on average for low, moderate, and severe cases, respectively using 15 input frames under daytime conditions and moderate frame rates. Similarly, the MFBD method provides, 40 percent, 29 percent, and 36 percent improvements in MSE on average under the same conditions. The comparison is repeated under low light conditions (less than 100 photons per pixel) where improvements of 39 percent, 29 percent and 27 percent are available using speckle imaging methods and 25 input frames and 38 percent, 34 percent and 33 percent respectively for the MFBD method and 150 input frames. The MFBD estimator is applied to three sets of field data and the results presented. Finally, a combined Bispectrum-MFBD Hybrid estimator is proposed and investigated. This technique consistently provides a lower MSE and smaller variance in the estimate under all three simulated turbulence conditions.

A COMPARATIVE STUDY OF HEURISTIC OPTIMIZATION ALGORITHMS

Heuristic optimization algorithms are of great importance for reaching solutions to various real world problems. These algorithms have a wide range of applications such as cost reduction, artificial intelligence, and medicine. By the term cost, one could imply that that cost is associated with, for instance, the value of a function of several independent variables. Often, when dealing with engineering problems, we want to minimize the value of a function in order to achieve an optimum, or to maximize another parameter which increases with a decrease in the cost (the value of this function). The heuristic cost reduction algorithms work by finding the optimum values of the independent variables for which the value of the function (the “cost”) is the minimum. There is an abundance of heuristic cost reduction algorithms to choose from. We will start with a discussion of various optimization algorithms such as Memetic algorithms, force-directed placement, and evolution-based algorithms. Following this initial discussion, we will take up the working of three algorithms and implement the same in MATLAB. The focus of this report is to provide detailed information on the working of three different heuristic optimization algorithms, and conclude with a comparative study on the performance of these algorithms when implemented in MATLAB. In this report, the three algorithms we will take in to consideration will be the non-adaptive simulated annealing algorithm, the adaptive simulated annealing algorithm, and random restart hill climbing algorithm. The algorithms are heuristic in nature, that is, the solution these achieve may not be the best of all the solutions but provide a means to reach a quick solution that may be a reasonably good solution without taking an indefinite time to implement.

Personal Digital Assistant 2.0 - A Software Prototype for Cognitive Cities

This paper presents a software prototype of a personal digital assistant 2.0. Based on soft computing methods and cognitive computing this mobile application prototype improves calendar and mobility management in cognitive cities. Applying fuzzy cognitive maps and evolutionary algorithms, the prototype represents a next step towards the realization of cognitive cities (i.e., smart cities enhanced with cognition). A user scenario and a test version of the prototype are included for didactical reasons.

Fast Algorithms Using Minimal Data Structures for Common Topological Relationships in Large, Irregularly-spaced Topographic Data Sets

Digital terrain models (DTM) typically contain large numbers of postings, from hundreds of thousands to billions. Many algorithms that run on DTMs require topological knowledge of the postings, such as finding nearest neighbors, finding the posting closest to a chosen location, etc. If the postings are arranged irregu- larly, topological information is costly to compute and to store. This paper offers a practical approach to organizing and searching irregularly-space data sets by presenting a collection of efficient algorithms (O(N),O(lgN)) that compute important topological relationships with only a simple supporting data structure. These relationships include finding the postings within a window, locating the posting nearest a point of interest, finding the neighborhood of postings nearest a point of interest, and ordering the neighborhood counter-clockwise. These algorithms depend only on two sorted arrays of two-element tuples, holding a planimetric coordinate and an integer identification number indicating which posting the coordinate belongs to. There is one array for each planimetric coordinate (eastings and northings). These two arrays cost minimal overhead to create and store but permit the data to remain arranged irregularly.

A proposal for the metrological characterization of circular features with digital optical machines

This paper aims to analyze the different adjustment methods commonly used to characterize indirect metrology circular features: least square circle, minimum zone circle, maximum inscribed circle and minimum circumscribed circle. The analysis was performed from images obtained by digital optical machines. The calculation algorithms, self-developed, have been implemented in Matlab® and take into consideration as study variables: the amplitude of angular sector of the circular feature, its nominal radio and the magnification used by the optical machine. Under different conditions, it was determined the radius and circularity error of different circular standards. The comparison of the results, obtained by the different methods of adjustments used, with certified values for the standards, has allowed us to determine the accuracy of each method and its scope.

Time evolution of frequency components In a chaotic digital signal

The type of signals obtained has conditioned chaos analysis tools. Almost in every case, they have analogue characteristics. But in certain cases, a chaotic digital signal is obtained and theses signals need a different approach than conventional analogue ones. The main objective of this paper will be to present some possible approaches to the study of this signals and how information about their characteristics may be obtained in the more straightforward possible way. We have obtained digital chaotic signals from an Optical Logic Cell with some feedback between output and one of the possible control gates. This chaos has been reported in several papers and its characteristics have been employed as a possible method to secure communications and as a way to encryption. In both cases, the influence of some perturbation in the transmission medium gave problems both for the synchronization of chaotic generators at emitter and receiver and for the recovering of information data. A proposed way to analyze the presence of some perturbation is to study the noise contents of transmitted signal and to implement a way to eliminate it. In our present case, the digital signal will be converted to a multilevel one by grouping bits in packets of 8 bits and applying conventional methods of time-frequency analysis to them. The results give information about the change in signals characteristics and hence some information about the noise or perturbations present. Equivalent representations to the phase and to the Feigenbaum diagrams for digital signals are employed in this case.

Sistema de autenticación accesible para el hogar digital

El Hogar Digital Accesible (HDA) de la ETSIST nace con el propósito de acercar las nuevas Tecnologías de la Información a las personas que precisan de necesidades concretas de accesibilidad y usabilidad, dotándoles de herramientas que les permitan aumentar su calidad de vida, confort, seguridad y autonomía. El entorno del HDA consta de elementos de control para puertas, persianas, iluminación, agua o gas, sensores de temperatura, incendios, gas, sistemas de climatización, sistemas de entretenimiento y sistemas de seguridad tales como detectores de presencia y alarmas. Todo ello apoyado sobre una arquitectura de red que proporciona una pasarela residencial y un acceso a banda ancha. El objetivo principal de este PFG ha sido el desarrollo de un sistema de autenticación para el Hogar Digital Accesible de bajo coste. La idea de integrar un sistema de autenticación en el HDA, surge de la necesidad de proteger de accesos no deseados determinados servicios disponibles dentro de un ámbito privado. Algunos de estos servicios pueden ser tales como el acceso a la lectura de los mensajes disponibles en el contestador automático, el uso de equipos multimedia, la desconexión de alarmas de seguridad o simplemente la configuración de ambientes según el usuario que esté autenticado (intensidad de luz, temperatura de la sala, etc.). En el desarrollo han primado los principios de accesibilidad, usabilidad y seguridad necesarios para la creación de un entorno no invasivo, que permitiera acreditar la identidad del usuario frente al sistema HDA. Se ha planteado como posible solución, un sistema basado en el reconocimiento de un trazo realizado por el usuario. Este trazo se usará como clave de cara a validar a los usuarios. El usuario deberá repetir el trazado que registró en el sistema para autenticarse. Durante la ejecución del presente PFG, se justificará la elección de este mecanismo de autenticación frente a otras alternativas disponibles en el mercado. Para probar la aplicación, se ha podido contar con dos periféricos de distintas gamas, el uDraw creado para la PS3 que se compone de una tableta digitalizadora y un lápiz que permite recoger los trazos realizados por el usuario de forma inalámbrica y la tableta digitalizadora Bamboo de Wacom. La herramienta desarrollada permite a su vez, la posibilidad de ser usada por otro tipo de dispositivos como es el caso del reloj con acelerómetro de 3 ejes de Texas Instruments Chronos eZ430 capaz de trasladar los movimientos del usuario al puntero de un ratón. El PFG se encuentra dividido en tres grandes bloques de flujo de trabajo. El primero se centra en el análisis del sistema y las tecnologías que lo componen, incluyendo los distintos algoritmos disponibles para realizar la autenticación basada en reconocimiento de patrones aplicados a imágenes que mejor se adaptan a las necesidades del usuario. En el segundo bloque se recoge una versión de prueba basada en el análisis y el diseño UML realizado previamente, sobre la que se efectuaron pruebas de concepto y se comprobó la viabilidad del proyecto. El último bloque incluye la verificación y validación del sistema mediante pruebas que certifican que se han alcanzado los niveles de calidad necesarios para la consecución de los objetivos planteados, generando finalmente la documentación necesaria. Como resultado del trabajo realizado, se ha obtenido un sistema que plantea una arquitectura fácilmente ampliable lograda a través del uso de técnicas como la introspección, que permiten separar la lógica de la capa de negocio del código que la implementa, pudiendo de forma simple e intuitiva sustituir código mediante ficheros de configuración, lo que hace que el sistema sea flexible y escalable. Tras la realización del PFG, se puede concluir que el producto final obtenido ha respondido de forma satisfactoria alcanzando los niveles de calidad requeridos, siendo capaz de proporcionar un sistema de autenticación alternativo a los convencionales, manteniendo unas cotas de seguridad elevadas y haciendo de la accesibilidad y el precio sus características más reseñables. ABSTRACT. Accessible Digital Home (HDA) of the ETSIST was created with the aim of bringing the latest information and communications technologies closer to the people who has special needs of accessibility and usability increasing their quality of life, comfort, security and autonomy. The HDA environment has different control elements for doors, blinds, lighting, water or gas, temperature sensors, fire protection systems, gas flashover, air conditioning systems, entertainments systems and security systems such as intruders detectors and alarms. Everything supported by an architecture net which provides a broadband residential services gateway. The main goal of this PFG was the development of a low-cost authentication system for the Accessible Digital Home. The idea of integrating an authentication system on the HDA, stems from the need to safeguard certain private key network resources from unauthorized access. Some of said resources are the access to the answering machine messages, the use of multimedia devices, the alarms deactivation or the parameter settings for each environment as programmed by the authenticated user (light intensity, room temperature, etc.). During the development priority was given to concepts like accessibility, usability and security. All of them necessary to create a non invasive environment that allows the users to certify their identity. A system based on stroke pattern recognition, was considered as a possible solution. This stroke is used as a key to validate users. The user must repeat the stroke that was saved on the system to validate access. The selection of this authentication mechanism among the others available options will be justified during this PFG. Two peripherals with different ranges were used to test the application. One of them was uDraw design for the PS3. It is wireless and is formed by a pen and a drawing tablet that allow us to register the different strokes drawn by the user. The other one was the Wacom Bamboo tablet, that supports the same functionality but with better accuracy. The developed tool allows another kind of peripherals like the 3-axes accelerometer digital wristwatch Texas Instruments Chronos eZ430 capable of transfering user movements to the mouse cursor. The PFG is divided by three big blocks that represent different workflows. The first block is focused on the system analysis and the technologies related to it, including algorithms for image pattern recognition that fits the user's needs. The second block describes how the beta version was developed based on the UML analysis and design previously done. It was tested and the viability of the project was verified. The last block contains the system verification and validation. These processes certify that the requirements have been fulfilled as well as the quality levels needed to reach the planned goals. Finally all the documentation has been produced. As a result of the work, an expandable system has been created, due to the introspection that provides the opportunity to separate the business logic from the code that implements it. With this technique, the code could be replaced throughout configuration files which makes the system flexible and highly scalable. Once the PFG has finished, it must therefore be concluded that the final product has been a success and high levels of quality have been achieved. This authentication tool gives us a low-cost alternative to the conventional ones. The new authentication system remains security levels reasonably high giving particular emphasis to the accessibility and the price.

Análisis, desarrollo y optimización de un sistema para el diseño de redes topográficas valorando el modelo digital del terreno

El presente trabajo tiene como objetivo general el análisis de las técnicas de diseño y optimización de redes topográficas, observadas mediante topografía convencional (no satelital) el desarrollo e implementación de un sistema informático capaz de ayudar a la definición de la geometría más fiable y precisa, en función de la orografía del terreno donde se tenga que ubicar. En primer lugar se realizará un estudio de la metodología del ajuste mediante mínimos cuadrados y la propagación de varianzas, para posteriormente analizar su dependencia de la geometría que adopte la red. Será imprescindible determinar la independencia de la matriz de redundancia (R) de las observaciones y su total dependencia de la geometría, así como la influencia de su diagonal principal (rii), números de redundancia, para garantizar la máxima fiabilidad interna de la misma. También se analizará el comportamiento de los números de redundancia (rii) en el diseño de una red topográfica, la variación de dichos valores en función de la geometría, analizando su independencia respecto de las observaciones así como los diferentes niveles de diseño en función de los parámetros y datos conocidos. Ha de señalarse que la optimización de la red, con arreglo a los criterios expuestos, está sujeta a los condicionantes que impone la necesidad de que los vértices sean accesibles, y además sean visibles entre sí, aquellos relacionados por observaciones, situaciones que dependen esencialmente del relieve del terreno y de los obstáculos naturales o artificiales que puedan existir. Esto implica la necesidad de incluir en el análisis y en el diseño, cuando menos de un modelo digital del terreno (MDT), aunque lo más útil sería la inclusión en el estudio del modelo digital de superficie (MDS), pero esta opción no siempre será posible. Aunque el tratamiento del diseño esté basado en un sistema bidimensional se estudiará la posibilidad de incorporar un modelo digital de superficie (MDS); esto permitirá a la hora de diseñar el emplazamiento de los vértices de la red la viabilidad de las observaciones en función de la orografía y los elementos, tanto naturales como artificiales, que sobre ella estén ubicados. Este sistema proporcionaría, en un principio, un diseño óptimo de una red constreñida, atendiendo a la fiabilidad interna y a la precisión final de sus vértices, teniendo en cuenta la orografía, lo que equivaldría a resolver un planteamiento de diseño en dos dimensiones y media1; siempre y cuando se dispusiera de un modelo digital de superficie o del terreno. Dado que la disponibilidad de obtener de manera libre el MDS de las zonas de interés del proyecto, hoy en día es costoso2, se planteará la posibilidad de conjuntar, para el estudio del diseño de la red, de un modelo digital del terreno. Las actividades a desarrollar en el trabajo de esta tesis se describen en esta memoria y se enmarcan dentro de la investigación para la que se plantean los siguientes objetivos globales: 1. Establecer un modelo matemático del proceso de observación de una red topográfica, atendiendo a todos los factores que intervienen en el mismo y a su influencia sobre las estimaciones de las incógnitas que se obtienen como resultado del ajuste de las observaciones. 2. Desarrollar un sistema que permita optimizar una red topográfica en sus resultados, aplicando técnicas de diseño y simulación sobre el modelo anterior. 3. Presentar una formulación explícita y rigurosa de los parámetros que valoran la fiabilidad de una red topográfica y de sus relaciones con el diseño de la misma. El logro de este objetivo se basa, además de en la búsqueda y revisión de las fuentes, en una intensa labor de unificación de notaciones y de construcción de pasos intermedios en los desarrollos matemáticos. 4. Elaborar una visión conjunta de la influencia del diseño de una red, en los seis siguientes factores (precisiones a posteriori, fiabilidad de las observaciones, naturaleza y viabilidad de las mismas, instrumental y metodología de estacionamiento) como criterios de optimización, con la finalidad de enmarcar el tema concreto que aquí se aborda. 5. Elaborar y programar los algoritmos necesarios para poder desarrollar una aplicación que sea capaz de contemplar las variables planteadas en el apartado anterior en el problema del diseño y simulación de redes topográficas, contemplando el modelo digital de superficie. Podrían considerarse como objetivos secundarios, los siguientes apartados: Desarrollar los algoritmos necesarios para interrelacionar el modelo digital del terreno con los propios del diseño. Implementar en la aplicación informática la posibilidad de variación, por parte del usuario, de los criterios de cobertura de los parámetros (distribución normal o t de Student), así como los grados de fiabilidad de los mismos ABSTRACT The overall purpose of this work is the analysis of the techniques of design and optimization for geodetic networks, measured with conventional survey methods (not satellite), the development and implementation of a computational system capable to help on the definition of the most liable and accurate geometry, depending on the land orography where the network has to be located. First of all, a study of the methodology by least squares adjustment and propagation of variances will be held; then, subsequently, analyze its dependency of the geometry that the network will take. It will be essential to determine the independency of redundancy matrix (R) from the observations and its absolute dependency from the network geometry, as well as the influence of the diagonal terms of the R matrix (rii), redundancy numbers, in order to ensure maximum re liability of the network. It will also be analyzed first the behavior of redundancy numbers (rii) in surveying network design, then the variation of these values depending on the geometry with the analysis of its independency from the observations, and finally the different design levels depending on parameters and known data. It should be stated that network optimization, according to exposed criteria, is subject to the accessibility of the network points. In addition, common visibility among network points, which of them are connected with observations, has to be considered. All these situations depends essentially on the terrain relief and the natural or artificial obstacles that should exist. Therefore, it is necessary to include, at least, a digital terrain model (DTM), and better a digital surface model (DSM), not always available. Although design treatment is based on a bidimensional system, the possibility of incorporating a digital surface model (DSM) will be studied; this will allow evaluating the observations feasibility based on the terrain and the elements, both natural and artificial, which are located on it, when selecting network point locations. This system would provide, at first, an optimal design of a constrained network, considering both the internal reliability and the accuracy of its points (including the relief). This approach would amount to solving a “two and a half dimensional”3 design, if a digital surface model is available. As the availability of free DSM4 of the areas of interest of the project today is expensive, the possibility of combining a digital terrain model will arise. The activities to be developed on this PhD thesis are described in this document and are part of the research for which the following overall objectives are posed: 1. To establish a mathematical model for the process of observation of a survey network, considering all the factors involved and its influence on the estimates of the unknowns that are obtained as a result of the observations adjustment. 2. To develop a system to optimize a survey network results, applying design and simulation techniques on the previous model. 3. To present an explicit and rigorous formulation of parameters which assess the reliability of a survey network and its relations with the design. The achievement of this objective is based, besides on the search and review of sources, in an intense work of unification of notation and construction of intermediate steps in the mathematical developments. 4. To develop an overview of the influence on the network design of six major factors (posterior accuracy, observations reliability, viability of observations, instruments and station methodology) as optimization criteria, in order to define the subject approached on this document. 5. To elaborate and program the algorithms needed to develop an application software capable of considering the variables proposed in the previous section, on the problem of design and simulation of surveying networks, considering the digital surface model. It could be considered as secondary objectives, the following paragraphs: To develop the necessary algorithms to interrelate the digital terrain model with the design ones. To implement in the software application the possibility of variation of the coverage criteria parameters (normal distribution or Student t test) and therefore its degree of reliability.

Diseño para fabricación digital: definición unívoca entre forma y fabricación en arquitectura

La presente investigación se inicia planteando el objetivo de identificar los parámetros geométricos que son exclusivos del proceso de generación de la Forma y relacionarlos con los invariantes relacionados con la Fabricación digital aplicada a la Arquitectura. Con ello se pretende recuperar la geometría como herramienta principal del proceso de Proyecto ampliando su ámbito de actuación al encontrar una relación con los procesos de fabricación digital. El primer capítulo describe los antecedentes y contexto histórico centrándose especialmente en la influencia de la capacidad de definir geometrías complejas digitalmente mediante la aplicación de algoritmos. En los primeros ejemplos la aproximación del Arquitecto a proyectos con geometrías complejas no euclídeas aún se emplea sin precisión en la comunicación de la geometría ideada para su puesta en obra. Las técnicas constructivas obligan a asumir una tolerancia de desviación entre proyecto y obra y la previsión del comportamiento de esa geometría no permite asegurar su comportamiento final. No será hasta la introducción de herramientas CAD en el proceso de ideación arquitectónica cuando el Arquitecto se capacite para generar geometrías no representables de forma analógica. Sin embargo, la imposibilidad de trasladar la geometría proyectada a la praxis constructiva impedirá la plasmación de un proceso completo, salvo en las contadas ocasiones que se recogen en este texto. “El análisis cronológico de las referencias establece como aspecto esencial para la construcción de geometrías complejas la capacidad primero para definir y comunicar de forma precisa e inequívoca la geometría y después la capacidad de analizar el desempeño prestacional de dicha propuesta geométrica”. La presente investigación se inicia planteando el objetivo de identificar los parámetros geométricos que son exclusivos del proceso de generación de la Forma y relacionarlos con los invariantes relacionados con la Fabricación digital aplicada a la Arquitectura. Con ello se pretende recuperar la geometría como herramienta principal del proceso de Proyecto ampliando su ámbito de actuación al encontrar una relación con los procesos de fabricación digital. El primer capítulo describe los antecedentes y contexto histórico centrándose especialmente en la influencia de la capacidad de definir geometrías complejas digitalmente mediante la aplicación de algoritmos. En los primeros ejemplos la aproximación del Arquitecto a proyectos con geometrías complejas no euclídeas aún se emplea sin precisión en la comunicación de la geometría ideada para su puesta en obra. Las técnicas constructivas obligan a asumir una tolerancia de desviación entre proyecto y obra y la previsión del comportamiento de esa geometría no permite asegurar su comportamiento final. No será hasta la introducción de herramientas CAD en el proceso de ideación arquitectónica cuando el Arquitecto se capacite para generar geometrías no representables de forma analógica. Sin embargo, la imposibilidad de trasladar la geometría proyectada a la praxis constructiva impedirá la plasmación de un proceso completo, salvo en las contadas ocasiones que se recogen en este texto. “El análisis cronológico de las referencias establece como aspecto esencial para la construcción de geometrías complejas la capacidad primero para definir y comunicar de forma precisa e inequívoca la geometría y después la capacidad de analizar el desempeño prestacional de dicha propuesta geométrica”. Establecida la primera conclusión, el capítulo de contexto histórico continúa enfocándose sobre la aplicación de las técnicas digitales en el Proceso de proyecto primero, y en la puesta en obra después. Los casos de estudio identifican claramente como un punto de inflexión para la generación de formas complejas mediante un software CAD el Museo Guggenheim de Bilbao en 1992. El motivo esencial para elegir este proyecto como el primer proyecto digital es el uso de la herramienta de definición digital de la geometría para su reproducción inequívoca en obra. “La revolución digital ha aportado al Arquitecto la posibilidad de abandonar las tipologías arquitectónicas basados en restricciones geométricas-constructivas. La aplicación de técnicas de fabricación digital ha permitido la capacidad de diseñar con independencia del sistema constructivo y libertad formal. En este nuevo contexto las prestaciones suponen los nuevos límites conceptuales, ya que el acceso y disposición de la información del comportamiento de las alternativas que cada geometría conlleva demanda del Arquitecto la jerarquización de los objetivos y la formulación en un conjunto coherente de parámetros”. Los proyectos que emplean herramientas digitales para la resolución de las distintas etapas del proceso proyectual se verán incrementados de forma exponencial desde 1992 hasta nuestros días. A pesar del importante auge de las técnicas de diseño asistido por ordenador el principal desafío sigue siendo la vinculación de las geometrías y materiales propuestos con las capacidades de las técnicas de manufactura y puesta en obra. El proceso de diseño para fabricación en un entorno digital es una tecnología madura en otras industrias como la aeroespacial o la automovilística, incluso la de productos de consumo y decoración, sin embargo en el sector de Construcción es un sistema inmaduro e inconexo. Las particularidades de la industria de la construcción aún no han sido abordadas en su totalidad y las propuestas de investigación realizadas en este ámbito se han centrado hasta 2015 en partes del proceso y no en el proceso total. “El principal obstáculo para la estandarización e implantación globalizada de un proceso digital desde el origen de la forma hasta la construcción es la inexistencia de un protocolo integrado que integre las limitaciones de fabricación, económicas y de puesta en obra junto a la evaluación de desempeño prestacional durante la fases iniciales de proyecto”. En el capítulo número 3 se estudian los distintos procesos de generación de la forma. Se propone una definición específica para el ámbito de la investigación de “forma” en el entendemos que se incluye la envolvente exterior y el conjunto organizativo de espacios interiores conectados. Por lo tanto no es excluyente del interior. El objetivo de este estudio es analizar y clasificar los procesos para la generación digital de formas en los distintos proyectos seleccionados como emblemáticos de cada tipología. Se concluye que la aproximación a este proceso es muy variada y compleja, con aplicación segregada y descoordinada entre los distintos agentes que han intervenir. En un proceso de generación formal analógico los parámetros que intervienen son en parte conscientes y en parte inconscientes o aprendidos. El Arquitecto sólo tiene control sobre la parte consciente de los parámetros a integrar en el diseño, de acuerdo a sus conocimientos y capacidades será capaz de manejar un número limitado de parámetros. La parte aprendida permanece en el inconsciente y dirige el proceso analógico, aportando prejuicios estéticos incorporados durante el proceso formativo y propio del entorno cultural. “El empleo de herramientas digitales basadas en la evaluación prestacional durante el proceso de selección formal permite al Arquitecto conocer “en tiempo real” el desempeño en el conjunto de prestaciones evaluadoras del conjunto de alternativas geométricas a la propuesta previamente definida por la intuición arquitectónica. El proceso definido no persigue identificar una solución óptima sino asistir al Arquitecto en el proceso de generación de la forma mediante la evaluación continua de los vectores direccionales más idóneos que el procedimiento generativo plantea”. La definición de complejidad en generación y producción de formas en relación con el proceso de diseño digital paramétrico global o integrado, es esencial para establecer un protocolo que optimice su gestión. “Se propone como definición de complejidad como factor resultante de multiplicar el número de agentes intervinientes por el número de parámetros e interacciones comunes que intervienen en el proceso de generación de la forma, dividido por la complejidad de intercambio de información digital desde el origen hasta la fase de fabricación y construcción”. Una vez analizados los procesos de generación digital de Arquitectura se propone identificar los parámetros geométricos que definen el proceso de Diseño digital, entendiendose por Diseño el proceso que engloba desde la proposición de una forma inicial basada en la intuición del Arquitecto, la generación y evaluación de variantes y posterior definición digital para producción, tanto de un objeto, un sistema o de la totalidad del Proyecto. En la actualidad el proceso de Diseño es discontinuo y lineal organizandose los parámetros por disciplinas en las que está estructurada las atribuciones profesionales en la industria de la construcción. Para simplificar la identificación y listado se han agrupado siguiendo estos grupos de conocimiento. Entendemos parametros invariables aquellos que son independientes de Tipologías arquitectónicas o que dependen del mismo proceso de generación de la Forma. “El listado de los parámetros que intervienen en un proceso de generación formal es una abstracción de una realidad compleja. La parametrización de las decisiones que intervienen en la selección de una forma determinada mediante “well defined problems” es imposible. El proceso que esta tesis describe entiende esta condición como un elemento que pone en valor el propio procedimiento generativo por la riqueza que la subjetividad que el equipo de diseño aporta”. La segunda parte esencial de esta investigación pretende extraer las restricciones propias del estado del arte de la fabricación digital para posteriormente incorporarlos en los procesos digitales de definición de la Forma arquitectónica. “La integración de las restricciones derivadas de las técnicas de fabricación y construcción digitales en el proceso de generación de formas desde el ámbito de la Arquitectura debe referirse a los condicionantes geométricos asociados a cada sistema constructivo, material y técnica de fabricación. La geometría es además el vínculo que permite asociar el conjunto de parámetros prestacionales seleccionados para un Proyecto con los sistemas de fabricación digital”. A estos condicionantes geométricos obtenidos del análisis de cada sistema de fabricación digital se les ha denominado “invariantes geométricos”. Bajo este término se engloban tanto límites dimensionales de fabricación, como materiales compatibles, tolerancias de manufactura e instalación y cualidades prestacionales asociadas. El objetivo de esta propuesta es emplear la geometría, herramienta fundamental y propia del Arquitecto, como nexo de unión entre el conjunto complejo y heterogéneo de parámetros previamente listados y analizados. Para ello se han simplificado en tablas específicas para cada parámetro prestacional los condicionantes geométricos que se derivan de los Sistemas de fabricación digital compatibles (ver apéndice 1). El estudio y evaluación de las capacidades y objetivos de las distintas plataformas de software disponibles y de las experiencias profesionales evaluadas en los proyectos presentados, permiten concluir que la propuesta de plataforma digital de diseño integral multi-paramétrico de formas arquitectónicas requiere de un protocolo de interoperatibilidad específico aún no universalmente establecido. Actualmente el enfoque de la estrategia para normalizar y universalizar el contexto normativo para regular la interoperatibilidad se centra en figura del gestor denominado “BIM manager”. Las atribuciones y roles de esta figura se enfocan a la gestión del continente y no del contenido (Definición de los formatos de intercambio, niveles de desarrollo (LOD) de los componentes o conjuntos constructivos, detección de interferencias y documentación del propio modelo). Siendo este ámbito un desarrollo necesario para la propuesta de universalización del sistema de diseño para fabricación digital integrado, la presente investigación aporta un organigrama y protocolo asociado. El protocolo: 1. Establece la responsabilidad de identificar y definir la Información que debe determinar el proceso de generación y desarrollo de la forma arquitectónica. 2. Define la forma digital apropiada para generar la geometría del Proyecto, incluyendo la precisión necesaria para cada componente y el nivel de detalle necesario para su exportación inequívoca al proceso de fabricación. 3. Define el tempo de cada etapa de diseño identificando un nivel de detalle acorde. 4. Acopla este organigrama dentro de las estructuras nuevas que se proponen en un entorno BIM para asegurar que no se producen solapes o vacíos con las atribuciones que se identifican para el BIM Manager. “El Arquitecto debe dirigir el protocolo de generación coordinada con los sistemas de producción digital para conseguir que la integración completa. El protocolo debe asistir al proceso de generación de forma mediante la evaluación del desempeño prestacional de cada variante en tiempo real. La comunicación entre herramientas digitales es esencial para permitir una ágil transmisión de información. Es necesario establecer un protocolo adaptado a los objetivos y las necesidades operativas de cada proyecto ya que la estandarización de un protocolo único no es posible”. Una decisión estratégica a la hora de planificar una plataforma de diseño digital común es establecer si vamos a optar por un Modelo digital único o diversos Modelos digitales federados. Cada uno de los modos de trabajo tiene fortalezas y debilidades, no obstante en el ámbito de investigación se ha concluido que un proceso integrado de Diseño que incorpore la evaluación prestacional y conceptual definida en el Capítulo 3, requiere necesariamente de varios modelos de software distintos que han de relacionarse entre sí mediante un protocolo de comunicación automatizado. Una plataforma basada en un modelo federado consiste en establecer un protocolo de comunicación entre los programas informáticos empleados por cada disciplina. En este modelo de operación cada equipo de diseño debe establecer las bases de comunicación en función del número y tipo de programas y procesos digitales a emplear. En esta investigación se propone un protocolo basado en los estándares de intercambio de información que estructura cualquier proceso de generación de forma paramétrico “La investigación establece el empleo de algoritmos evolutivos como el sistema actual óptimo para desarrollar un proceso de generación de formas basadas en la integración y coordinación de invariantes geométricos derivados de un conjunto de objetivos prestacionales y constructivos. No obstante, para la aplicación en el caso práctico realizado se ha podido verificar que la evaluación del desempeño aún no puede realizarse en una única herramienta y por lo tanto el proceso de selección de las variantes genéticas óptimas ha de ejecutarse de forma manual y acumulativa. El proceso debe realizarse de manera federada para la selección evolutiva de los invariantes geométricos dimensionales”. La evaluación del protocolo de integración y los condicionantes geométricos obtenidos como parámetros geométricos que controlan las posibles formas compatibles se realiza mediante su aplicación en un caso práctico. El ejercicio simula la colaboración multidisciplinar con modelos federados de plataformas distintas. La elección del tamaño y complejidad constructiva del proyecto se ha modulado para poder alcanzar un desarrollo completo de cada uno de los parámetros prestacionales seleccionados. Continuando con el mismo objetivo propuesto para los parámetros prestacionales, la tipología constructiva-estructural seleccionada para el ejercicio permite la aplicación la totalidad de invariantes geométricos asociados. El objetivo de este caso práctico es evaluar la capacidad alterar la forma inicialmente propuesta mediante la evaluación del desempeño prestacional de conjunto de variantes geométricas generadas a partir de un parámetro dimensional determinado. Para que este proceso tenga sentido, cada una de las variantes debe ser previamente validada conforme a las limitaciones geométricas propias de cada sistema de fabricación y montaje previstos. El interés de las conclusiones obtenidas es la identificación de una variante geométrica distante a la solución simétrica inicialmente como la solución óptima para el conjunto de parámetros seleccionados. Al tiempo se ha comprobado como la participación de un conjunto de parámetros multi-disciplinares que representan la realidad compleja de los objetivos arquitectónicos favorecen la aparición de variaciones genéticas con prestaciones mejoradas a la intuición inicial. “La herencias tipológicas suponen un límite para la imaginación de variantes formales al proceso de ideación arquitectónica. El ejercicio realizado demuestra que incluso en casos donde aparentemente la solución óptima aparenta ser obvia una variante aleatoria puede mejorar su desempeño global. La posibilidad de conocer las condiciones geométricas de las técnicas de fabricación digital compatibles con el conjunto de parámetros seleccionados por el Arquitecto para dirigir el proceso asegura que los resultados del algoritmo evolutivo empleado sean constructivamente viables. La mejora de imaginación humana con la aportación de geometrías realmente construibles supone el objetivo último de esta tesis”. ABSTRACT Architectural form generation process is shifting from analogical to digital. Digital technology has changed the way we design empowering Architects and Engineers to precisely define any complex geometry envisioned. At the same time, the construction industry, following aeronautical and automotive industries, is implementing digital manufacturing techniques to improve efficiency and quality. Consequently construction complexity will no longer be related to geometry complexity and it is associated to coordination with digital manufacturing capacities. Unfortunately it is agreed that non-standard geometries, even when proposed with performance optimization criteria, are only suitable for projects with non-restricted budgets. Furthemore, the lack of coordinated exportation protocol and geometry management between design and construction is avoiding the globalization of emergence process in built projects Present research first objective is to identify exclusive form-generation parameters related to digital manufacturing geometrical restraints. The intention was to use geometry as the form-generation tool and integrate the digital manufacturing capacities at first stages of the project. The first chapter of this text describes the investigation historical context focusing on the influence between accurate geometry definition at non-standard forms and its construction. At first examples of non-Euclidean geometries built the communication between design and construction were based on analogical partial and imprecise documentation. Deficient communication leads to geometry adaptation on site leaving the final form uncontrolled by the Architect. Computer Aided Design enable Architects to define univocally complex geometries that previously where impossible to communicate. “The univocally definition of the Form, and communication between design and construction is essential for complex geometry Projects”. The second chapter is focused on digital technologies application in form finding process and site construction. The case studies selected identifies a clear inflexion node at 1992 with the Guggenheim Museum in Bilbao. The singularity of this project was the use of Aeronautics software to define digitally the external envelope complex geometry to enable the contractor to build it. “The digital revolution has given the Architect the capacity to design buildings beyond the architectural archetypes driven by geometric-constructive limitations. The application of digital manufacturing techniques has enabled a free-form construction without geometrical limitations. In this new context performance shall be the responsible to set new conceptual boundaries, since the behavior of each possible geometry can be compare and analyze beforehand. The role of the Architect is to prioritize the performance and architectural objectives of each project in a complete and coherent set of parameters”. Projects using digital tools for solving various stages of the design process were increased exponentially since 1992 until today. Despite the significant rise of the techniques of computer-aided design the main challenge remains linking geometries and materials proposed at each design with the capabilities of digital manufacturing techniques. Design for manufacturing in a digital environment is a mature technology in other industries such as aerospace and automotive, including consumer products and decoration, but in the construction sector is an immature and disjointed system. The peculiarities of the construction industry have not yet been addressed in its entirety and research proposals made in this area until 2015 have focused in separate parts of the process and not the total process. “The main obstacle to global standardization and implementation of a complete digital process from the form-finding to construction site is the lack of an integrated protocol that integrates manufacturing, economic and commissioning limitations, together with the performance evaluation of each possible form”. The different form generation processes are studied at chapter number 3. At the introduction of this chapter there is a specific definition of "form" for the research field. Form is identified with the outer envelope geometry, including the organizational set of connected indoor spaces connected to it. Therefore it is not exclusive of the interior. The aim of this study is to analyze and classify the main digital form generation processes using different selected projects as emblematic of each type. The approach to this process is complex, with segregated and uncoordinated different actors have to intervene application. In an analogical form-generation process parameters involved are partly conscious and partly unconscious or learned. The architect has control only over limited part of the parameters to be integrated into the design, according to their knowledge and. There is also a learned aesthetical prejudice that leads the form generation process to a specific geometry leaving the performance and optimization criteria apart from the decision making process. “Using performance evaluation digital tools during form finding process provides real-time comparative information to the Architect enabling geometry selection based on its performance. The generative form generation process described at this document does not ambition to identify the optimum geometry for each set of parameters. The objective is to provide quick information at each generation of what direction is most favorable for the performance parameters selected”. Manufacturing complexity definition in relation to a global and integral process of digital design for manufacture is essential for establishing an efficient managing protocol. “The definition of complexity associated to design for production in Architecture is proposed as the factor between number of different agents involved in the process by the number of interactions required between them, divided by the percentage of the interchange of information that is standardized and proof of information loss”. Design in architecture is a multi-objective process by definition. Therefore, addressing generation process linked to a set of non-coherent parameters requires the selection of adequate generative algorithm and the interaction of the architect. During the second half of the twentieth century and early twenty-first century it have been developed various mathematical algorithms for multi-parametric digital design. Heuristic algorithms are the most adequate algorithms for architectural projects due to its nature. The advantage of such algorithms is the ability to efficiently handle large scale optimization cases where a large number of design objectives and variables are involved. These generative processes do not pursue the optimum solution, in fact it will be impossible to proof with such algorithm. This is not a problem in architectural design where the final goal is to guide the form finding process towards a better performance within the initial direction provided by the architect. This research has focused on genetic algorithms due to its capacity to generate geometric alternatives in multiple directions and evaluate the fitness against a set of parameters specified in a single process. "Any protocol seeks to achieve standardization. The design to manufacturing protocol aims to provide a coordinated and coherent form generation process between a set of design parameters and the geometrical requirements of manufacturing technique. The protocol also provides an information exchange environment where there is a communication path and the level of information is ensured. The research is focused on the process because it is considered that each project will have its own singularities and parameters but the process will stay the same. Again the development of a specific tool is not a goal for the research, the intention is to provide an open source protocol that is valid for any set of tools”. Once the digital generation processes are being analized and classified, the next step is to identify the geometric parameters that define the digital design process. The definition of design process is including from the initial shape proposal based on the intuition of the architect to the generation, evaluation, selection and production of alternatives, both of an object , system or of the entire project . The current design process in Architecture is discontinuous and linear, dividing the process in disciplines in which the construction industry is structured. The proposal is to unify all relevant parameters in one process. The parameters are listed in groups of knowledge for internal classification but the matrix used for parameter relationship determination are combined. “A multi-parameter determination of the form-finding process is the integration all the measurable decisions laying behind Architect intuition. It is not possible to formulate and solve with an algorithm the design in Architecture. It is not the intention to do so with the proposal of this research. The process aims to integrate in one open protocol a selection of parameters by using geometry as common language. There is no optimum solution for any step of the process, the outcome is an evaluation of performance of all the form variations to assist the Architect for the selection of the preferable solution for the project”. The research follows with the geometrical restrictions of today Digital manufacturing techniques. Once determined it has been integrated in the form-finding process. “Digital manufacturing techniques are integrated in the form-finding process using geometry as common language. Geometric restraints define the boundary for performance parametric form-finding process. Geometrical limitations are classified by material and constructive system”. Choose between one digital model or several federate models is a strategic decision at planning a digital design for manufacturing protocol. Each one of the working models have strengths and weakens, nevertheless for the research purposes federated models are required to manage the different performance evaluation software platforms. A protocol based on federated models shall establish a communication process between software platforms and consultants. The manager shall integrate each discipline requirements defining the communication basis. The proposed protocol is based on standards on information exchange with singularities of the digital manufacturing industry. “The research concludes evolutionary algorithms as current best system to develop a generative form finding process based on the integration and coordination of a set of performance and constructive objectives. However, for application in professional practice and standardize it, the performance evaluation cannot be done in only one tool and therefore the selection of optimal genetic variants must be run in several iterations with a cumulative result. Consequently, the evaluation process within the geometrical restraints shall be carried out with federated models coordinated following the information exchange protocol”. The integration protocol and geometric constraints evaluation is done by applying in a practical case study. The exercise simulates multidisciplinary collaboration across software platforms with federated models. The choice of size and construction complexity of the project has been modulated to achieve the full development of each of the parameters selected. Continuing with the same objective proposed for the performance parameters the constructive and structural type selected for the exercise allows the application all geometric invariants associated to the set of parameters selected. The main goal of the case study is to proof the capacity of the manufacturing integrated form finding process to generate geometric alternatives to initial form with performance improved and following the restrictions determined by the compatible digital manufacturing technologies. The process is to be divided in consecutive analysis each one limited by the geometrical conditions and integrated in a overall evaluation. The interest of this process is the result of a non-intuitive form that performs better than a double symmetrical form. The second conclusion is that one parameter evaluation alone will not justify the exploration of complex geometry variations, but when there is a set of parameters with multidisciplinary approach then the less obvious solution emerge as the better performing form. “Architectural typologies impose limitation for Architects capacity to imagine formal variations. The case study and the research conclusions proof that even in situations where the intuitive solution apparently is the optimum solution, random variations can perform better when integrating all parameters evaluation. The capacity of foreseing the geometrical properties linking each design parameter with compatible manufacturing technologies ensure the result of the form-finding process to be constructively viable. Finally, the propose of a complete process where the geometry alternatives are generated beyond the Architect intuition and performance evaluated by a set of parameters previously selected and coordinated with the manufacturing requirements is the final objective of the Thesis”.