Efeito da incorporação de diatomita na estabilidade e permeabilidade de compósitos cimentíceos espumados aplicados a poços de petróleo

Lightweight oilwell cement slurries have been recently studied as a mean to improve zonal isolation and sheath-porous formation adherence. Foamed slurries consisting of Portland cement and air-entraining admixtures have become an interesting option for this application. The loss in hydrostatic pressure as a consequence of cement hydration results in the expansion of the air bubbles entrapped in the cement matrix, thus improving the sheath-porous formation contact. Consequently, slurries are able to better retain their water to complete the hydration process. The main objective of the present study was to evaluate the effect of the addition of an air-entraining admixture on the density, stability and permeability of composite slurries containing Portland cement and diatomite as light mineral load. Successful formulations are potential cementing materials for low fracture gradient oilwells. The experimental procedures used for slurry preparation and characterization were based on the American Petroleum Institute and ABNT guidelines Slurries containing a pre-established concentration of the air-entraining admixture and different contents of diatomite were prepared aiming at final densities of 13 to 15 lb/gal. The results revealed that the reduction of 15 to 25% of the density of the slurries did not significantly affect their strength. The addition of both diatomite and the air-entraining admixture increased the viscosity of the slurry providing better air-bubble retention in the volume of the slurry. Stable slurries depicted bottom to top density variation of less than 1.0 lb/gal and length reduction of the stability sample of 5.86 mm. Finally, permeability coefficient values between 0.617 and 0.406 mD were obtained. Therefore, lightweight oilwell cement slurries depicting a satisfactory set of physicochemical and mechanical properties can be formulated using a combination of diatomite and air-entraining admixtures for low fracture gradient oilwells

Uso de argilominerais e diatomita como adsorvente de fenóis em águas produzidas na indústria de petróleo

The oil production in Brazil has been increasing each year. Consequently, increasing volumes of water produced are generated with large quantities of contaminants, which brings many problems in disposing of these waters. The concern that the concentrations of contaminants in water produced meet existing laws for disposal of effluents, has been extremely important for the development of different techniques for treatment of water produced. The study of clay minerals as adsorbents of organic contaminants has grown considerably so in order to combine the low cost with the efficiency of environmental preservation and health issues. Thus, this study aims to understand the characteristics of vermiculite clay, sodium bentonite, calcium bentonite and diatomite and evaluate their performance as adsorbents for phenol in the water produced. Through adsorption isotherms it was possible to observe the behavior of these adsorptive clay and diatomite for adsorption of phenol, the main phenolic compound found in water produced. Different concentrations of synthetic solutions of phenol were put in touch with these adsorbents under same conditions of agitation and temperature. The adsorbents were composted adsorptive favorable, but the vermiculite and diatomite showed little capacity for absorption, being suggested for absorbs small concentrations of phenol in the balance isothermal

Formulação e caracterização de pastas espumadas por incorporação de ar e estabilizantes minerais

Cementing operations may occur at various stages of the life cycle of an oil well since its construction until its definitive abandonment. There are some situations in which the interest zones are depleted or have low fracture pressure. In such cases, the adoption of lowdensity cement slurries is an efficient solution. To this end, there are basically three ways to reduce the density of cement slurries: using microspheres, water extending additives or foamed cement. The objective of this study is to formulate, to study and to characterize lowdensity foamed cement, using an air entrainment surfactant with vermiculite or diatomite as water extenders and stabilizers. The methodology consists on preparation and evaluation of the slurries under the American Petroleum Institute (API) and the Brazilian Association of Technical Standards (ABNT) guidelines. Based on calculated densities between 13 and 15 ppg (1.559 and 1.799 g/cm3), the slurries were prepared with fixed surfactant concentration, varying the concentrations of vermiculite and diatomite and were compared with the base slurries. The results of plastic viscosity, yield point and gel strength and the compressive strength for 24 h showed that the slurries presented suitable rheology and mechanical strength for cementing operations in oil wells, and had their densities reduced between 8.40 and 11.89 ppg (1.007 and 1.426 g/cm3). The conclusion is that is possible, under atmospheric conditions, to obtain light weighted foamed cement slurries with satisfactory rheological and mechanical properties by means of air entrainment and mineral additions with extenders and stabilizers effects. The slurries have great potential for cementing operations; applicability in deep wells, in low fracture gradient formations and in depleted zones and bring cost savings by reducing the cementing consumption

Perdas fermentativas e composição bromatológica da entrecasca de palmito pupunha ensilada com aditivos químicos

Objetivou-se avaliar o efeito da inclusão de aditivos químicos na ensilagem de resíduos (entrecasca) da produção de palmito pupunha (Bactris gasipaes, Kunth). Utilizaram-se silos experimentais (baldes de 20 litros) providos de aparatos para determinação gravimétrica de perdas por gases e efluentes. Os tratamentos aplicados foram: controle (sem aditivos); ureia (1% da MV) e cal virgem (1% da MV). Decorridos 70 dias de armazenagem, os silos foram pesados, abertos e amostrados. As perdas por efluentes e gases aumentaram com a aplicação de cal virgem na ensilagem. As perdas totais de MS foram de 15,1; 14,4 e 26,6% nas silagens controle, ureia e cal, respectivamente. em todas as silagens, houve redução no teor de FDN e elevação da fração FDA, o que indica desaparecimento da fração hemicelulose. A relação cálcio:fósforo aumentou substancialmente com a adição de cal virgem, de 4,1:1 na silagem controle para 15,6:1 na silagem com cal. O resíduo da extração do palmito pupunha pode ser classificado como alimento de média qualidade e alto teor de umidade. Os aditivos aplicados na ensilagem não são efetivos em reduzir as perdas fermentativas no processo de conservação.

Impact of maintenance of Macrobrachium rosenbergii de Man, 1879 (Crustacea, Decapoda, Palaemonidae) broodstock on the water used in culture ponds

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Anaerobic bio-digestion of concentrate obtained in the process of ultra filtration of effluents from tilapia processing unit

The objective of the present study was to evaluate the efficiency of the process of biodigestion of the protein concentrate resulting from the ultrafiltration of the effluent from a slaughterhouse freezer of Nile tilapia. Bench digesters were used with excrements and water (control) in comparison with a mixture of cattle manure and effluent from the stages of filleting and bleeding of tilapias. The effluent obtained in the continuous process (bleeding + filleting) was the one with highest accumulated population from the 37th day, as well as greatest daily production. Gases composition did not differ between the protein concentrates, but the gas obtained with the use of the effluent from the filleting stage presented highest methane gas average (78.05%) in comparison with those obtained in the bleeding stage (69.95%) and in the continuous process (70.02%) or by the control method (68.59%).

Biodigestão anaeróbia dos dejetos de cabritos Saanen alimentados com dietas com diferentes proporções volumoso e concentrado

Avaliaram-se os efeitos da idade do animal e da proporção de volumoso nas dietas sobre a biodigestão anaeróbia dos dejetos de cabritos Saanen. Foram utilizadas as fezes produzidas por cabritos Saanen aos 90, 120 e 150 dias de idade e alimentados com dietas de três relações volumoso:concentrado (80:20, 60:40 e 40:60), representando as dietas 1, 2 e 3, respectivamente. Utilizaram-se biodigestores tipo batelada de bancada com capacidade para 12 litros de substrato em fermentação e 8% de sólidos totais iniciais para determinação das produções e dos potenciais de produção de biogás e metano, da redução de sólidos voláteis e quantificação dos teores de minerais no afluente e efluente. As maiores reduções de sólidos voláteis foram observadas nos substratos preparados com as fezes de cabritos aos 150 dias alimentados com a dieta com relação volumoso:concentrado de 40:60. Os melhores rendimentos de substrato ou fezes foram obtidos com os dejetos dos cabritos de 120 e 150 dias de idade alimentados com a dieta com relação volumoso:concentrado 40:60. As maiores concentrações de minerais nos biodigestores foram observadas para as fezes de cabritos de 150 dias de idade alimentados com a dieta com relação volumoso:concentrado 40:60. A biodigestão anaeróbia é eficiente na remoção de coliformes nos dejetos de caprinos, proporcionando efluentes com no máximo 4,3 × 10² coliformes totais termotolerantes por grama de material.

Queima e aditivos químicos e bacterianos na ensilagem de cana-de-açúcar

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Perdas de silagens de cana-de-açúcar tratadas com aditivos químicos e bacterianos

Objetivou-se avaliar silagens de cana-de-açúcar tratadas com aditivos químicos (uréia 1,5%; benzoato de sódio 0,1%; ou hidróxido de sódio (NaOH) 1% na matéria natural) combinados ou não com inoculantes (Propionibacterium acidipropionici + Lactobacillus plantarum ou Lactobacillus buchneri). Foram avaliadas 12 silagens: uma controle, sem inoculante e sem aditivo químico; três sem inoculante, mas com um dos aditivos; uma com P. acidipropionici + L. plantarum, sem aditivo químico; três com P. acidipropionici + L. plantarum e um dos aditivos; uma com L. buchneri, sem aditivo químico; e três com L. buchneri e um dos aditivos. Os dados foram analisados em esquema fatorial 4 × 3 com três repetições para cada tratamento. Foram determinadas as perdas ocorridas durante o processo fermentativo nas formas de gases e de efluentes e a recuperação da MS. Durante a exposição aeróbia, determinaram-se a recuperação da MS e a estabilidade aeróbia medida pela variação da temperatura. A associação de L. buchneri e NaOH reduziu as perdas por gases e efluentes e elevou a recuperação da MS. No período após abertura, destacou-se a atuação do benzoato de sódio em manter o pH com variação de apenas 0,1 unidade em cinco dias de exposição aeróbia e dos inoculantes L. buchneri e P. acidipropionici + L. plantarum em prolongar o tempo para elevação da temperatura de 34 horas nas silagens controle para 54 e 50 horas, respectivamente. A ensilagem de cana-de-açúcar requer a inclusão de algum aditivo eficiente no controle das perdas quantitativas durante a fermentação e a exposição aeróbia.

Avaliação mecânica e microestrutural de compósitos de poliéster com adição de cargas minerais e resíduos industriais

With the current growth in consumption of industrialized products and the resulting increase in garbage production, their adequate disposal has become one of the greatest challenges of modern society. The use of industrial solid residues as fillers in composite materials is an idea that emerges aiming at investigating alternatives for reusing these residues, and, at the same time, developing materials with superior properties. In this work, the influence of the addition of sand, diatomite, and industrial residues of polyester and EVA (ethylene vinyl acetate), on the mechanical properties of polymer matrix composites, was studied. The main objective was to evaluate the mechanical properties of the materials with the addition of recycled residue fillers, and compare to those of the pure polyester resin. Composite specimens were fabricated and tested for the evaluation of the flexural properties and Charpy impact resistance. After the mechanical tests, the fracture surface of the specimens was analyzed by scanning electron microscopy (SEM). The results indicate that some of the composites with fillers presented greater Young s modulus than the pure resin; in particular composites made with sand and diatomite, where the increase in modulus was about 168 %. The composites with polyester and EVA presented Young s modulus lower than the resin. Both strength and maximum strain were reduced when fillers were added. The impact resistance was reduced in all composites with fillers when compared to the pure resin, with the exception of the composites with EVA, where an increase of about 6 % was observed. Based on the mechanical tests, microscopy analyses and the compatibility of fillers with the polyester resin, the use of industrial solid residues in composites may be viable, considering that for each type of filler there will be a specific application

Evolução da biodegradabilidade da matéria orgânica em um sistema de lagoas de estabilização

Waste stabilization ponds (WSP) have been widely used for sewage treatment in hot climate regions because they are economic and environmentally sustainable. In the present study a WSP complex comprising a primary facultative pond (PFP) followed by two maturation ponds (MP-1 and MP-2) was studied, in the city of Natal-RN. The main objective was to study the bio-degradability of organic matter through the determination of the kinetic constant k throughout the system. The work was carried out in two phases. In the first, the variability in BOD, COD and TOC concentrations and an analysis of the relations between these parameters, in the influent raw sewage, pond effluents and in specific areas inside the ponds was studied. In the second stage, the decay rate for organic matter (k) was determined throughout the system based on BOD tests on the influent sewage, pond effluents and water column samples taken from fixed locations within the ponds, using the mathematical methods of Least Squares and the Thomas equation. Subsequently k was estimated as a function of a hydrodynamic model determined from the dispersion number (d), using empirical methods and a Partial Hydrodynamic Evaluation (PHE), obtained from tracer studies in a section of the primary facultative pond corresponding to 10% of its total length. The concentrations of biodegradable organic matter, measured as BOD and COD, gradually reduced through the series of ponds, giving overall removal efficiencies of 71.95% for BOD and of 52.45% for COD. Determining the values for k, in the influent and effluent samples of the ponds using the mathematical method of Least Squares, gave the following values respectively: primary facultative pond (0,23 day-1 and 0,09 day-1), maturation 1 (0,04 day-1 and 0,03 day-1) and maturation 2 (0,03 day-1 and 0,08 day-1). When using the Thomas method, the values of k in the influents and effluents of the ponds were: primary facultative pond (0,17 day-1 and 0,07 day-1), maturation 1 (0,02 day-1 and 0,01 day-1) and maturation 2 (0,01 day-1 and 0,02 day-1). From the Partial Hydrodynamic Evaluation, in the first section of the facultative pond corresponding to 10% of its total length, it can be concluded from the dispersion number obtained of d = 0.04, that the hydraulic regime is one of dispersed flow with a kinetic constant value of 0.20 day-1

Produção de forragem verde em sistema hidropônico usando esgoto tratado

In the urban areas of the cities a larger problem of destiny of effluents of the treatment stations is verified due to the junction of the sewages in great volumes. This way the hidroponic cultive becomes important, for your intensive characteristic, as alternative of reuse. This work presents as objective the improvement of the relation hidric-nutritious of the hidroponic cultive of green forage (FVH) using treaty sewage. The production of forage was with corn (Zea mays L.), using double hybrid AG1051, in the experimental field of the Federal University of Rio Grande do Norte (UFRN), in the city of Natal-RN-Brazil. The treated effluent essentially domestic had origin of anaerobic reactor, type decant-digester of two cameras in series followed by anaerobic filters drowned. The hidroponic experimental system was composed of 08 stonemasons, with limited contours for masonry of drained ceramic brick, measuring each one 2,5 meters in length for 1,0 meter of width, with inclination of 4% (m/m) in the longitudinal sense, leveled carefully, in way to not to allow preferential roads in the flow. These dimensions, the useful area of Isow was of 2 square meters. The stonemasons of cultive were waterproof (found and lateral) with plastic canvas of 200 micres of thickness, in the white color. Controlled the entrance and exit of the effluente in the stonemasons, with cycles of 12,68 minutes, it being water of 1,18 minutes. The treatments were constituted of: T1 - 24 hours/day under it waters with flow of 2 L/min; T2 - 12 hours/day under waters with flow of 4 L/min; T3 - 12 hours/day under waters with flow of 2 L/min; and T4 - 16 hours/day under waters with flow of 3 L/min. There were evaluations of the evapotranspirometric demand, of hidroponic system affluent and effluent seeking to characterize and to monitor physical-chemical parameters as: pH, temperature, Electric Conductivity and Fecal Coliforms. This last one was analyzed to the 11 days after isow (DAS) and to the 14 DAS. The others were analyzed daily. I sow it was accomplished in the dates of February 21, 2007, first experiment, and April 10, 2007, second experiment. The density of Isow was of 2 kg of seeds, germinated before 48 hours, for square meter of stonemason. The statistic delineament was it casual entirely with two repetitions, in two experiments. It was applied Tukey test of average to five percent of probability. The cultivation cycle was of 14 DAS with evapotranspirometric demand maximum, reached by T1, of 67,44 mm/day. The analyzed parameters, as mass of green matter - Kg, productivity-Kg/m2 and reason of production of seed FVH/Kg used in Isow, the best result was presented by T1, obtaining value of up to 19,01 Kg/m2 of cultive. Without significant difference, the T4 presented greats values with 16 hours under cycle of water. The Treatments 2 and 3 with 12 hours under cycle of water, they obtained inferior results to the other Treatments. As treatment system, came efficient in the reduction of the salinity. T1 obtained reduction medium maxim of 62,5%, to the 7 DAS, in the amount of salts that enter in the system in they are absorbed in the cultivation. The cultivation FVH acted reducing the microbiologic load. Significant percentile of reduction they were reached, with up to 90,23% of reduction of Units of Colonies (UFC), constituting, like this, the Hidroponic System as good alternative of treatment of effluents of Reactors of high Efficiency

Encapsulação de nanopartículas de magnetita em matriz de poli(metacrilato de metilacoácido metacrílico) por processo de polimerização em miniemulsão

Magnetic particles are systems with potential use in drug delivery systems, ferrofluids, and effluent treatment. In many situations, such as in biomedical applications, it is necessary to cover magnetic particles with an organic material, as polymers. In this work, magnetic particles were obtained through covering magnetite particles with poly(methyl methacrylate‐comethacrylic acid) via miniemulsion polymerization process. The resultant materials were characterized X‐ray diffraction (XRD), Fourier Transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), zeta potential (��) measurements and vibrating sample magnetometry (VSM). XRD results showed magnetite as the predominant cristalline phase in all samples and that cristallites had nanometric dimensions. Thermogravimetric analysis revealed an increase in polymer thermal stability as a result of magnetite encapsulation. TGA results showed also that the encapsulation efficiency was directly related to nanoparticles s hidrofobicity degree. VSM measurements showed that magnetic polymeric particles were superparamagnetic, so that they may be potentially used for magnetic (bio)separation

Impacto da manutenção de reprodutores de macrobrachium rosenbergii na qualidade da água

Our objective was to evaluate the impacts caused on pond water quality by maintenance of Macrobrachium rosenbergii broodstock. During eight weeks we determined pH, dissolved oxygen (DO), conductivity, turbidity, particulate suspended material (PSM), nitrogen (N) and phosphorus (P), all in inlet and effluent water. All variables presented higher values in the effluent, except OD. N-ammoniacal concentration (0.013 mg L(-1)) was 2.7 times higher in the effluent pond; NO(2)-N (0.019 mg L(-1)), 2.3; NO(3)-N (0.139 mu g L(-1)), 1.8; PO(4)-P (0.065 mg L(-1)), 7.2; and DP (0,104 mg L(-1)), 4.9 times higher. For TKN (0.67 mg L(-1)) and TP (0.235 mg L(-1)) the values in the pond effluent represent an increase of 0.27 mg L(-1) and 0.175 mg L(-1), respectively. The maintenance of M. rosenbergii broodstock increase the nutrient concentrations, mainly TP, prevent effluent pond released into receiving water bodies on 1, 2 and 3 classes of the CONAMA N degrees 357 Resolution.

Biodigestão anaeróbia dos resíduos da produção avícola: cama de frangos e carcaças

O propósito deste trabalho foi avaliar a produção de biogás, bem como os potenciais de produção e a qualidade do biofertilizante obtido com a biodigestão anaeróbia dos resíduos cama de frangos e carcaças de aves pré-compostados. Para tanto, foram pré-compostados cama de frango e carcaças de aves mortas em uma composteira durante um período de 60 dias, período necessário para que ocorresse decomposição prévia das carcaças e assim fosse possível manipular o material para abastecer os biodigestores. Após este período, o material foi utilizado para abastecer os biodigestores batelada de campo com capacidade de 60 litros de material em fermentação. Para o processo de biodigestão anaeróbia, foram efetuadas análises dos teores de sólidos totais (ST), sólidos voláteis (SV), composição química do efluente, potenciais de produção, além do número mais provável (NMP) de coliformes totais e termotolerantes no afluente e efluente. Os potenciais médios de produção de biogás foram: 0,073; 0,152 e 0,141m³.kg-1 de material, SV e ST adicionados, respectivamente. Foram observadas reduções acima de 99% no NMP de coliformes totais e termotolerantes, sendo observado NMP de 3,7 x 10(5) g-1 no início e 7,45 x 10² g-1 no final.