Digital Control Implementation to Reduce the Cost and Improve the Performance of the Control Stage of an Industrial Switched-Mode Power Supply

The main objective of this work is the design and implementation of the digital control stage of a 280W AC/DC industrial power supply in a single low-cost microcontroller to replace the analog control stage. The switch-mode power supply (SMPS) consists of a PFC boost converter with fixed frequency operation and a variable frequency LLC series resonant DC/DC converter. Input voltage range is 85VRMS-550VRMS and the output voltage range is 24V-28V. A digital controller is especially suitable for this kind of SMPS to implement its multiple functionalities and to keep the efficiency and the performance high over the wide range of input voltages. Additional advantages of the digital control are reliability and size. The optimized design and implementation of the digital control stage it is presented. Experimental results show the stable operation of the controlled system and an estimation of the cost reduction achieved with the digital control stage.

An overview of fast DC-DC converters for envelope amplifier in RF transmitters

In the last years, RF power amplifiers are taking advantage of the switched dc-dc converters to use them in several architectures that may improve the efficiency of the amplifier, keeping a good linearity. The use of linearization techniques such as Envelope Elimination and Restoration (EER) and Envelope Tracking (ET) requires a very fast dc-dc power converter to provide variable voltage supply to the power amplifier but theoretically the efficiency can be much higher than using the classical amplifiers belonging to classes A, B or AB. The purpose of this paper is to analyze the state of the art of the power converters used as envelope amplifiers in this application where a fast output voltage variation is required. The power topologies will be explored and several important parameters such as efficiency, bandwidth and output voltage range will be discussed.

Estudo comparativo de dois conversores Boost quadrático com comutação suave monochaveados para aplicação de rastreamento de máxima potência em sistemas fotovoltaicos

This paper makes a comparative study of two Soft Single Switched Quadratic Boost Converters (SSS1 and SSS2) focused on Maximum Power Point Tracking (MPPT) of a PV array using Perturb and Observe (P&O) algorithm. The proposed converters maintain the static gain characteristics and dynamics of the original converter with the advantage of considerably reducing the switching losses and Electromagnetic Interference (EMI). It is displayed the input voltage Quadratic Boost converter modeling; qualitative and quantitative analysis of soft switching converters, defining the operation principles, main waveforms, time intervals and the state variables in each operation steps, phase planes of resonant elements, static voltage gain expressions, analysis of voltage and current efforts in semiconductors and the operational curves at 200 W to 800 W. There are presented project of PI, PID and PID + Notch compensators for MPPT closed-loop system and resonant elements design. In order to analyze the operation of a complete photovoltaic system connected to the grid, it was chosen to simulate a three-phase inverter using the P-Q control theory of three-phase instantaneous power. Finally, the simulation results and experimental with the necessary comparative analysis of the proposed converters will be presented.

Análise e projeto de um conversor boost de três níveis intercalado

This paper presents the development of a boost converter with the possibility of higher gain than the conventional boost converter for applications under similar conditions and increased power. Presents the main concepts involving the boost converter and two variations: the boost converter of three levels and the boost converter interspersed with two converter cells. The breakdown mounting positions, the operating steps, the addressing and the main strengths of each converter in order to check for possible uses in the construction of a prototype joining their main advantages. In the presentation of this converter addresses the operating steps, the equation governing its design, the simulations obtained through software (PSIM), a comparison between the boost converter models studied and the experimental results.

Analisi e ottimizzazione di un convertitore DC-DC impiegato come circuito di interfaccia per un carico rigenerativo

Questa tesi è stata svolta in collaborazione con un’azienda di Cesena che si occupa della progettazione e costruzione di caricabatterie e saldatrici e si pone come scopo di analizzare quello che viene chiamato carico "rigenerativo" un dispositivo che permette di testare e collaudare questo tipo di macchine consumando la minor energia elettrica possibile. In particolare si discuterà come avviene il funzionamento del circuito di interfaccia e la sua resa energetica attraverso alcune simulazioni con vari tipi di carichi. Verrà anche presa in esame una prova con il circuito realizzato e confrontata con quella analoga svolta al simulatore.

Projecto, montagem e teste de uma unidade modular de detecção de radiação Geiger-Muller

Dissertação para obtenção do grau de Mestre em Engenharia Electrotécnica Ramo de Automação e Electrónica Industrial

Projeto e implementação de um pré-regulador de fator de potência com controlo digital

Hoje em dia as fontes de alimentação possuem correção do fator de potência, devido às diversas normas regulamentares existentes, que introduziram grandes restrições no que respeita à distorção harmónica (THD) e fator de potência (FP). Este trabalho trata da análise, desenvolvimento e implementação de um Pré-Regulador de fator de potência com controlo digital. O controlo digital de conversores com recurso a processamento digital de sinal tem vindo a ser ao longo dos últimos anos, objeto de investigação e desenvolvimento, estando constantemente a surgirem modificações nas topologias existentes. Esta dissertação tem como objetivo estudar e implementar um Pré-Regulador Retificador Boost e o respetivo controlo digital. O controlo do conversor é feito através da técnica dos valores médios instantâneos da corrente de entrada, desenvolvido através da linguagem de descrição de hardware VHDL (VHSIC HDL – Very High Speed Integrated Circuit Hardware Description Language) e implementado num dispositivo FPGA (Field Programmable Gate Array) Spartan-3E. Neste trabalho são apresentadas análises matemáticas, para a obtenção das funções de transferência pertinentes ao projeto dos controladores. Para efetuar este controlo é necessário adquirir os sinais da corrente de entrada, tensão de entrada e tensão de saída. O sinal resultante do módulo de controlo é um sinal de PWM com valor de fator de ciclo variável ao longo do tempo. O projeto é simulado e validado através da plataforma MatLab/Simulink e PSIM, onde são apresentados resultados para o regime permanente e para transitórios da carga e da tensão de alimentação. Finalmente, o Pré-Regulador Retificador Boost controlado de forma digital é implementado em laboratório. Os resultados experimentais são apresentados para validar a metodologia e o projeto desenvolvidos.

PV systems linked to the grid: parameter identification with a heuristic procedure

This paper focuses on a PV system linked to the electric grid by power electronic converters, identification of the five parameters modeling for photovoltaic systems and the assessment of the shading effect. Normally, the technical information for photovoltaic panels is too restricted to identify the five parameters. An undemanding heuristic method is used to find the five parameters for photovoltaic systems, requiring only the open circuit, maximum power, and short circuit data. The I- V and the P- V curves for a monocrystalline, polycrystalline and amorphous photovoltaic systems are computed from the parameters identification and validated by comparison with experimental ones. Also, the I- V and the P- V curves under the effect of partial shading are obtained from those parameters. The modeling for the converters emulates the association of a DC-DC boost with a two-level power inverter in order to follow the performance of a testing commercial inverter employed on an experimental system. © 2015 Elsevier Ltd.

Inversor fotovoltaico para utilização em ambiente doméstico

Dissertação para obtenção do Grau de Mestre em Engenharia Electrotécnica e de Computadores

Predictive control of a current-source inverter for solar photovoltaic grid interface

Solar photovoltaic systems are an increasing option for electricity production, since they produce electrical energy from a clean renewable energy resource, and over the years, as a result of the research, their efficiency has been increasing. For the interface between the dc photovoltaic solar array and the ac electrical grid is necessary the use of an inverter (dc-ac converter), which should be optimized to extract the maximum power from the photovoltaic solar array. In this paper is presented a solution based on a current-source inverter (CSI) using continuous control set model predictive control (CCS-MPC). All the power circuits and respective control systems are described in detail along the paper and were tested and validated performing computer simulations. The paper shows the simulation results and are drawn several conclusions.

OnBoard reconfigurable battery charger for electric vehicles with traction-to-auxiliary mode

This paper proposes a single-phase reconfigurable battery charger for Electric Vehicle (EV) that operates in three different modes: Grid-to-Vehicle (G2V) mode, in which the traction batteries are charged from the power grid; Vehicle-to-Grid (V2G) mode, in which the traction batteries deliver part of the stored energy back to the power grid; and in Traction-to-Auxiliary (T2A) mode, in which the auxiliary battery is charged from the traction batteries. When connected to the power grid, the battery charger works with sinusoidal current in the AC side, for both G2V and V2G modes, and also regulates the reactive power. When the EV is disconnected from the power grid, the control algorithms are modified and the full-bridge AC-DC bidirectional converter works as a full-bridge isolated DC-DC converter that is used to charge the auxiliary battery of the EV, avoiding the use of an additional charger to accomplish this task. To assess the behavior of the proposed reconfigurable battery charger under different operation scenarios, a 3.6 kW laboratory prototype has been developed and experimental results are presented.

Eines interactives per l'aprenentatge de la dinàmica i el control dels convertidors de potència

El projecte s'ha centrat en el disseny i desenvolupament de laboratoris virtuals per a la docència del dispositius i mètodes de gestió d’energia. Això s’ha realitzat a dos nivells clarament diferenciats, el primer grup de laboratoris correspon als convertidors electrònics de potencia i el segon grup de laboratoris correspon a un conjunt de casos d’aplicacions concretes. En el primer grup es descriu el detall del funcionament dels diferents elements mentre que en el segon els descriuen les idees i conceptes bàsics de funcionament. Els laboratoris virtuals de convertidors electrònics de potència inclouen el convertidor elevador (boost), el convertidor reductor (buck), i convertidors acobladors magnèticament. Aquestes permeten estudiar el comportament dinàmica des d’un punt de vista commutat o bé promitjat, les aplicacions incorporen també la possibilitat de sintonitzar els controladors. Aquestes aplicacions han estat desenvolupades per ser un complement per les sessions de pràctiques presencials. Els laboratoris virtuals d’aplicacions, inclouen els sistema de transport metropolità, el vehicle híbrid i els sistemes de gestió de talls transitoris en el subministrament d’energia principalment. Aquestes laboratoris permeten introduir els estudiants de forma qualitativa en els diferents conceptes i tècniques emprades en els sistemes de generació, transport i transformació d’energia. Totes les aplicacions han estat desenvolupades emprant Easy JAVA Simulations, aquesta eina permet desenvolupar laboratoris multiplataforma fàcilment distribuïbles a través d’internet.

Sign Inventory Users Guide, August 2010

This User’s Guide serves as a reference for field personnel using the sign inventory data collection software tool. This tool was developed to simplify and standardize the collection and updating of sign inventory information. The software and collection methodology was developed by the Iowa DOT Sign Management Task Force and the Center for Transportation Research and Education at Iowa State University. Required Equipment -The data collection process requires both a portable computer and a global positioning system (GPS) device (connected via USB cable). Since computer battery performance varies, a DC power converter is recommended. A check-in/out process has also been established which allows updates to sign information from the central database.

Teholähdepiirilevyn suunnittelu akkukäyttöiseen laitteeseen

Teholähdepiirilevyn suunnittelu etenkin kooltaan pieneen akkukäyttöiseen laitteeseen on monivaiheinen suunnitteluprosessi. Teholähdetopologioiden valinta levylle määrää heti alkuunsa kuinka vakaata jännitettä levyllä voidaan tuottaa, kuinka suuria tehoja siitä voidaan ottaa, miten paljon häiriöitä levy tuottaa ympäristöönsä ja ennen kaikkea, kun akkukäyttöisestä laitteesta on kysymys, kuinka hyvään hyötysuhteeseen sillä voidaan päästä. Suunnittelun kannalta hakkuriteholähde on teholähdetopologioista vaativin. Tässä työssä paneudutaankin tarkemmin boost-hakkuriteholähteen suunnitteluun. Pelkkä hakkurin komponenttien mitoitus ei takaa teholähteelle parasta mahdollista toimintaa, vaan myös piirilevysuunnittelulla on suuri merkitys. Akkukäyttöisen laitteen teholähdepiirilevyn suunnittelu ei rajoitu yksinomaan teholähteiden suunnitteluun vaan levy sisältää usein myös muuta oheiselektroniikkaa, yleensä ainakin laitteen käynnistyselektroniikan sekä akun latausjärjestelmän. Etenkin akun latausjärjestelmän suunnittelu saattaa muodostua hyvinkin monimutkaiseksi tehtäväksi. Tässä työssä onkin tutkittu muutaman yleisimmän akkutyypin latausmenetelmiä. Työssä suunnitellaan myös käytännössä teholähdepiirilevy akkukäyttöiseen mittalaitteeseen. Levyn toimintaa tutkitaan erinäisin mittauksin, joilla pyritään selvittämään levyn heikkoudet. Näiden heikkouksien pohjalta levystä suunnitellaan paranneltu versio. Tällekin levylle tehdään samat mittaukset kuin edelliselle versiolle, joista selviää parannusten onnistuminen.

Tasasähkönjakeluverkon vaihtosuuntaaja galvaanisella erotuksella

Suomessa sähkönjakeluverkko koostuu pääasiassa 20 kV ja 400 V jännitetasoista. Tällöin sähkö viedään lähelle kuluttajia suuremmalla jännitetasolla ja muunnetaan alhaisemmaksi lähellä asiakkaita. Haittapuolena on se, että haja-asutusalueilla jakelumuuntajien määrä kasvaa suureksi, koska ne täytyy sijoittaa lähelle kuluttajaa. Vaihtoehtona on toteuttaa osa sähkönjakelusta tasajännitteellä, jolloin tehollinen jännite olisi suurempi. Tällöin sähköä voitaisiin siirtää pidempiä matkoja ilman, että asiakaskohtaisia tai muutaman asiakkaan kattavia 20 kV siirtolinjoja tarvitsisi käyttää. Tämä taasen edellyttää asiakaskohtaisien vaihtosuuntaajien käyttöä. Tässä työssä esiteltävällä 1 kVA vaihtosuuntaajalla muodostetaan tasasähköjakeluverkosta saatavasta 750 V tasasähköstä yksivaiheista (230 VRMS, 50 Hz) verkkojännitettä. Laite on suunniteltu toteuttamaan galvaaninen erotus mahdollisimman hyvän hyötysuhteen puitteissa. Vaihtosuuntaaja on toteutettu käyttämällä resonanssikonvertteria, joka vaihtosuuntaa jakelujännitteen korkeataajuiseksi vaihtojännitteeksi. Tämän jälkeen toteutetaan galvaaninen erotus käyttäen suurtaajuusmuuntajaa. Tätä seuraa syklokonvertteri, joka pulssintiheysmodulaatiota soveltaen muodostaa lähtöjännitteen. Tämä suodatetaan lopuksi LC- alipäästösuotimella säröltään standardin mukaiseksi. Laite on jaettu työssä kolmeen osaan, joista jokaisen toiminta on selitetty ja simuloitu itsenäisesti. Lopussa koko järjestelmä on simuloitu yhtenä kokonaisuutena. Hyötysuhteeksi arvioitiin karkeasti 94 % ja lopullisista tuloksista voidaan päätellä, että laitteen toteuttaminen prototyypiksi voisi olla kannattavaa.