Fine wire resistance thermometer amplifier for atmospheric measurements

An improved amplifier for atmospheric fine wire resistance thermometry is described. The amplifier uses a low excitation current (50 mu A). This is shown to ensure negligible self-heating of the low mass fine wire resistance sensor, compared with measured nocturnal surface air temperature fluctuations. The system provides sufficient amplification for a +/- 50 degrees C span using a +/- 5 V dynamic range analog-to-digital converter, with a noise level of less than 0.01 degrees C. A Kelvin four-wire connection cancels the effect of long lead resistances: a 50 m length of screened cable connecting the Reading design of fine wire thermometer to the amplifier produced no measurable temperature change at 12 bit resolution.

Improved and optimal dual circular 32-QAM for MB-OFDM

Quadrature Phase Shift Keying (QPSK) and Dual Carrier Modulation (DCM) are currently used as the modulation schemes for Multiband Orthogonal Frequency Division Multiplexing (MB-OFDM) in the ECMA-368 defined Ultra-Wideband (UWB) radio platform. ECMA-368 has been chosen as the physical radio platform for many systems including Wireless USB (W-USB), Bluetooth 3.0 and Wireless HDMI; hence ECMA-368 is an important issue to consumer electronics and the users’ experience of these products. To enable the transport of high-rate USB, ECMA-368 offers up to 480 Mb/s instantaneous bit rate to the Medium Access Control (MAC) layer, but depending on radio channel conditions dropped packets unfortunately result in a lower throughput. This paper presents improvement on a high data rate modulation scheme that fits within the configuration of the current standard increasing system throughput by achieving 600 Mb/s (reliable to 3.2 meters) thus maintaining the high rate USB throughput even with a moderate level of dropped packets. The modulation system is termed improved and optimal Dual Circular 32-QAM (DC 32-QAM). The system performance for improved and optimal DC 32-QAM modulation is presented and compared with previous DC 32- QAM, 16-QAM and DCM.

Enhancing MB-OFDM throughput with dual circular 32-QAM

Quadrature Phase Shift Keying (QPSK) and Dual Carrier Modulation (DCM) are currently used as the modulation schemes for Multiband Orthogonal Frequency Division Multiplexing (MB-OFDM) in the ECMA-368 defined Ultra-Wideband (UWB) radio platform. ECMA-368 has been chosen as the physical radio platform for many systems including Wireless USB (W-USB), Bluetooth 3.0 and Wireless HDMI; hence ECMA-368 is an important issue to consumer electronics and the users experience of these products. To enable the transport of high-rate USB, ECMA-368 offers up to 480 Mb/s instantaneous bit rate to the Medium Access Control (MAC) layer, but depending on radio channel conditions dropped packets unfortunately result in a lower throughput. This paper presents an alternative high data rate modulation scheme that fits within the configuration of the current standard increasing system throughput by achieving 600 Mb/s (reliable to 3.1 meters) thus maintaining the high rate USB throughput even with a moderate level of dropped packets. The modulation system is termed Dual Circular 32-QAM (DC 32-QAM). The system performance for DC 32-QAM modulation is presented and compared with 16-QAM and DCM1.

The current status of anticoagulant resistance in rats and mice in the UK

Introduction: Resistance to anticoagulants in Norway rats (Rattus norvegicus) and house mice (Mus domesticus) has been studied in the UK since the early 1960s. In no other country in the world is our understanding of resistance phenomena so extensive and profound. Almost every aspect of resistance in the key rodent target species has been examined in laboratory and field trials and results obtained by independent researchers have been published. It is the principal purpose of this document to present a short synopsis of this information. More recently, however, the development of genetical techniques has provided a definitive means of detection of resistant genotypes among pest rodent populations. Preliminary information from a number of such surveys will also be presented. Resistance in Norway rats: A total of nine different anticoagulant resistance mutations (single nucleotide polymorphisms or SNPs) are found among Norway rats in the UK. In no other country worldwide are present so many different forms of Norway rat resistance. Among these nine SNPs, five are known to confer on rats that carry them a significant degree of resistance to anticoagulant rodenticides. These mutations are: L128Q, Y139S, L120Q, Y139C and Y139F. The latter three mutations confer, to varying degrees, practical resistance to bromadiolone and difenacoum, the two second-generation anticoagulants in predominant use in the UK. It is the recommendation of RRAG that bromadiolone and difenacoum should not be used against rats carrying the L120Q, Y139C and Y139F mutations because this will promote the spread of resistance and jeopardise the long-term efficacy of anticoagulants. Brodifacoum, flocoumafen and difethialone are effective against these three genotypes but cannot presently be used because of the regulatory restriction that they can only be applied against rats that are living and feeding predominantly indoors. Our understanding of the geographical distribution of Norway rat resistance in incomplete but is rapidly increasing. In particular, the mapping of the focus of L120Q Norway rat resistance in central-southern England by DNA sequencing is well advanced. We now know that rats carrying this resistance mutation are present across a large part of the counties of Hampshire, Berkshire and Wiltshire, and the resistance spreads into Avon, Oxfordshire and Surrey. It is also found, perhaps as outlier foci, in south-west Scotland and East Sussex. L120Q is currently the most severe form of anticoagulant resistance found in Norway rats and is prevalent over a considerable part of central-southern England. A second form of advanced Norway rat resistance is conferred by the Y139C mutation. This is noteworthy because it occurs in at least four different foci that are widely geographically dispersed, namely in Dumfries and Galloway, Gloucestershire, Yorkshire and Norfolk. Once again, bromadiolone and difenacoum are not recommended for use against rats carrying this genotype and a concern of RRAG is that continued applications of resisted active substances may result in Y139C becoming more or less ubiquitous across much of the UK. Another type of advanced resistance, the Y139F mutation, is present in Kent and Sussex. This means that Norway rats, carrying some degree of resistance to bromadiolone and difenacoum, are now found from the south coast of Kent, west into the city of Bristol, to Yorkshire in the north-east and to the south-west of Scotland. This difficult situation can only deteriorate further where these three genotypes exist and resisted anticoagulants are predominantly used against them. Resistance in house mice: House mouse is not so well understood but the presence in the UK of two resistant genotypes, L128S and Y139C, is confirmed. House mice are naturally tolerant to anticoagulants and such is the nature of this tolerance, and the presence of genetical resistance, that house mice resistant to the first-generation anticoagulants are considered to be widespread in the UK. Consequently, baits containing warfarin, sodium warfarin, chlorophacinone and coumatetralyl are not approved for use against mice. This regulatory position is endorsed by RRAG. Baits containing brodifacoum, flocoumafen and difethialone are effective against house mice and may be applied in practice because house mouse infestations are predominantly indoors. There are some reports of resistance among mice in some areas to the second-generation anticoagulant bromadiolone, while difenacoum remains largely efficacious. Alternatives to anticoagulants: The use of habitat manipulation, that is the removal of harbourage, denial of the availability of food and the prevention of ingress to structures, is an essential component of sustainable rodent pest management. All are of importance in the management of resistant rodents and have the advantage of not selecting for resistant genotypes. The use of these techniques may be particularly valuable in preventing the build-up of rat infestations. However, none can be used to remove any sizeable extant rat infestation and for practical reasons their use against house mice is problematic. Few alternative chemical interventions are available in the European Union because of the removal from the market of zinc phosphide, calciferol and bromethalin. Our virtual complete reliance on the use of anticoagulants for the chemical control of rodents in the UK, and more widely in the EU, calls for improved schemes for resistance management. Of course, these might involve the use of alternatives to anticoagulant rodenticides. Also important is an increasing knowledge of the distribution of resistance mutations in rats and mice and the use of only fully effective anticoagulants against them.

Integrable maps with non-trivial topology: application to divertor configurations

We explore a method for constructing two-dimensional area-preserving, integrable maps associated with Hamiltonian systems, with a given set of fixed points and given invariant curves. The method is used to find an integrable Poincare map for the field lines in a large aspect ratio tokamak with a poloidal single-null divertor. The divertor field is a superposition of a magnetohydrodynamic equilibrium with an arbitrarily chosen safety factor profile, with a wire carrying an electric current to create an X-point. This integrable map is perturbed by an impulsive perturbation that describes non-axisymmetric magnetic resonances at the plasma edge. The non-integrable perturbed map is applied to study the structure of the open field lines in the scrape-off layer, reproducing the main transport features obtained by integrating numerically the magnetic field line equations, such as the connection lengths and magnetic footprints on the divertor plate.

Conformational Properties of Angiotensin II and Its Active and Inactive TOAC-Labeled Analogs in the Presence of Micelles. Electron Paramagnetic Resonance, Fluorescence, and Circular Dichroism Studies

The interaction between angiotensin II (AII, DRVYIHPF) and its analogs carrying 2,2,6,6-tetramethylpiperidine-1-oxyl-4-amino-4-carboxylic acid (TOAC) and detergents-negatively charged sodium dodecyl sulfate (SDS) and zwitterionic N-hexadecyl-N,N-dimethyl-3-ammonio-1-propanesulfonate (HPS)-was examined by means of EPR, CD, and fluorescence. EPR spectra of partially active TOAC(1)-AII and inactive TOAC(3)-AII in aqueous solution indicated fast tumbling, the freedom of motion being greater at the N-terminus. Line broadening occurred upon interaction with micelles. Below SDS critical micelle concentration, broader lines indicated complex formation with tighter molecular packing than in micelles. Small changes in hyperfine splittings evinced TOAC location at the micelle-water interface. The interaction with anionic micelles was more effective than with zwitterionic micelles. Peptide-micelle interaction caused fluorescence increase. The TOAC-promoted intramolecular fluorescence quenching was more, pronounced for TOAC(3)-AII because of the proximity between the nitroxide and Tyr(4). CD spectra showed that although both AII and TOAC(1)-AII presented flexible conformations in water, TOAC(3)-AII displayed conformational restriction because of the TOAC-imposed bend (Schreier et al., Biopolymers 2004, 74, 389). In HPS, conformational changes were observed for the labeled peptides at neutral and basic pH. In SDS, all peptides underwent pH-dependent conformational changes. Although the spectra suggested similar folds for All and TOAC(1)-AII, different conformations were acquired by TOAC(3)-AII. The membrane environment has been hypothesized to shift conformational equilibria so as to stabilize the receptor-bound conformation of ligands. The fact that TOAC(3)-AII is unable to acquire conformations similar to those of native AII and partially active TOAC(1)-AII is probably the explanation for its lack of biological activity. (C) 2009 Wiley Periodicals, Inc. Biopolymers (Pept Sci) 92: 525-537, 2009.

Tribological Testing of Some Potential PVD and CVD Coatings for Steel Wire Drawing Dies

Cemented carbide is today the most frequently used drawing die material in steel wire drawing applications. This is mainly due to the possibility to obtain a broad combination of hardness and toughness thus meeting the requirements concerning strength, crack resistance and wear resistance set by the wire drawing process. However, the increasing cost of cemented carbide in combination with the possibility to increase the wear resistance of steel through the deposition of wear resistant CVD and PVD coatings have enhanced the interest to replace cemented carbide drawing dies with CVD and PVD coated steel wire drawing dies. In the present study, the possibility to replace cemented carbide wire drawing dies with CVD and PVD coated steel drawing dies have been investigated by tribological characterisation, i.e. pin-on-disc and scratch testing, in combination with post-test observations of the tribo surfaces using scanning electron microscopy, energy dispersive X-ray spectroscopy and 3D surface profilometry. Based on the results obtained, CVD and PVD coatings aimed to provide improved tribological performance of steel wire drawing dies should display a smooth surface topography, a high wear resistance, a high fracture toughness (i.e. a high cracking and chipping resistance) and intrinsic low friction properties in contact with the wire material. Also, the steel substrate used must display a sufficient load carrying capacity and resistance to thermal softening. Of the CVD and PVD coatings evaluated in the tribological tests, a CVD TiC and a PVD CrC/C coating displayed the most promising results.

Universal zero-bias conductance through a quantum wire side-coupled to a quantum dot

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Vortex lattice of a long superconducting wire with a columnar defect

In the present work we study a long superconducting wire with a columnar defect in the presence of an applied magnetic field. The cross section of the cylinder is assumed to be circular. The field is taken uniform and parallel to the cylinder axis. We use the London theory to investigate the vortex lattice inside the wire. Although this theory is valid in the limit of low vortex density, that is, when the nearest neighbor vortex distance is much larger than the coherence length, we can obtain a reasonable qualitative description of lattice properties. We calculate: (1) the vortex lattice structure using the simulated annealing technique; (2) the magnetization curve as a function of the applied field.

Vortex lattice and matching fields for a long superconducting wire

We investigate the flux penetration patterns and matching fields of a long cylindrical wire of circular cross section in the presence of an external magnetic field. For this study we write the London theory for a long cylinder both for the mixed and Meissner states, with boundary conditions appropriate for this geometry. Using the Monte Carlo simulated annealing method, the free energy of the mixed state is minimized with respect to the vortex position and we obtain the ground state of the vortex lattice for N=3 up to 18 vortices. The free energy of the Meissner and mixed states provides expressions for the matching fields. We find that, as in the case of samples of different geometry, the finite-size effect provokes a delay on the vortex penetration and a vortex accumulation in the center of the sample. The vortex patterns obtained are in good agreement with experimental results.

Size effects in the magnetization of a superconducting wire

The size effects in the magnetization of a long cylindrical wire of circular cross section in the presence of an external magnetic field are investigated. For this study the London theory is used with boundary conditions appropriate for this geometry. Using the Monte Carlo simulated annealing method, the free energy of the mixed state is minimized with respect to the vortex positions. The ground state of the vortex lattice for n = 1 up to 18 vortices for a given radius of the cylinder is obtained. It is found that the finite size of the sample provokes a matching effect in the magnetization, as found in experiments with superconducting samples of finite size but different geometry. © 1999 American Institute of Physics.

Distribution line models analysis for loss calculation within three-phase three-wire power flow algorithms

Three-phase three-wire power flow algorithms, as any tool for power systems analysis, require reliable impedances and models in order to obtain accurate results. Kron's reduction procedure, which embeds neutral wire influence into phase wires, has shown good results when three-phase three-wire power flow algorithms based on current summation method were used. However, Kron's reduction can harm reliabilities of some algorithms whose iterative processes need loss calculation (power summation method). In this work, three three-phase three-wire power flow algorithms based on power summation method, will be compared with a three-phase four-wire approach based on backward-forward technique and current summation. Two four-wire unbalanced medium-voltage distribution networks will be analyzed and results will be presented and discussed. © 2004 IEEE.

Shunt active compensation based on the Conservative Power Theory current's decomposition

Considering the operation of shunt active compensators, such as active power filters, this paper proposes possible compensation strategies by means of the recent formulation of the Conservative Power Theory (CPT). The CPT current's decomposition results in several current components, which are associated with specific load characteristics (power transfer, energy storage, unbalances and/or non linearities). These current components are used for the definition of different compensation strategies, which can be selective in terms of minimizing particular disturbing effects. In order to validate the applicability of these new compensation strategies, simulation and experimental results for three-phase four-wire systems are presented. © 2011 IEEE.

Dipolo e escoamento uniforme: escoamento em torno de um cilindro circular

The study of movements of ideals fluids is more simple that the viscous fluids because do not have the presence of tension of shear. The normal tensions are the one that must be considered in this analysis. The theory corresponding to these flows is the same used in other fields of the physics called Theory of Potentials Fields, which the vector identity is fundamental. Any flow into irrotational (null vorticity) physically possibly has a current function and a potential of velocity that satisfied the equation of Laplace. Reciprocally, any solution of equation of Laplace represents a current function or a potential of velocity of a flow into physically possible. Once the equation of Laplace is linear, the addiction of any numbers of solutions is also a solution. So, several potentials flows into can be constructed superposing configurations of elementary flows into. The purpose of the superposition of elementary flows into is a production of similar configurations to those of practical interest. The combination of mathematical elegancy with utility in the potential flow into attracted many for its study. Some of the most famous mathematician of history studied the theory and application of “hydrodynamic”, how was called the potential fluid into before 1900

Large-Scale Population Analysis Challenges the Current Criteria for the Molecular Diagnosis of Fascioscapulohumeral Muscular Dystrophy

Facioscapulohumeral muscular dystrophy (FSHD) is a common hereditary myopathy causally linked to reduced numbers (<= 8) of 3.3 kilobase D4Z4 tandem repeats at 4q35. However, because individuals carrying D4Z4-reduced alleles and no FSHD and patients with FSHD and no short allele have been observed, additional markers have been proposed to support an FSHD molecular diagnosis. In particular a reduction in the number of D4Z4 elements combined with the 4A(159/161/168)PAS haplotype (which provides the possibility of expressing DUX4) is currently used as the genetic signature uniquely associated with FSHD. Here, we analyzed these DNA elements in more than 800 Italian and Brazilian samples of normal individuals unrelated to any FSHD patients. We find that 3% of healthy subjects carry alleles with a reduced number (4-8) of D4Z4 repeats on chromosome 4q and that one-third of these alleles, 1.3%, occur in combination with the 4A161PAS haplotype. We also systematically characterized the 4q35 haplotype in 253 unrelated FSHD patients. We find that only 127 of them (50.1%) carry alleles with 1-8 D4Z4 repeats associated with 4A161PAS, whereas the remaining FSHD probands carry different haplotypes or alleles with a greater number of D4Z4 repeats. The present study shows that the current genetic signature of FSHD is a common polymorphism and that only half of FSHD probands carry this molecular signature. Our results suggest that the genetic basis of FSHD, which is remarkably heterogeneous, should be revisited, because this has important implications for genetic counseling and prenatal diagnosis of at-risk families.