Beeinflussung der Grenzflächenspannung zwischen den Schmelzen "unverträglicher" Homopolymere durch Copolymere

Im Rahmen dieser Arbeit wurde am System Polyethylenoxid / Polypropylenoxid (PEO / PPO) der Einfluß von Copolymeren auf die Grenzflächenspannung Sigma von Homopolymerblends untersucht. Als Additive dienten Triblockcopolymere EO-block-PO-block-EO bzw. PO-block-EO-block-PO, Diblockcopolymere S-block-EO sowie statistische Copolymere EO-ran-PO. Die Additive wurden so ausgewählt, daß sich Paare von Additiven jeweils in genau einer Eigenschaft (Zusammensetzung, Kettenlänge, Blockanordnung) unterscheiden, in allen anderen Parametern jedoch vergleichbar sind. Die Grenzflächenspannung wurde experimentell mit Hilfe der Pendant-Drop-Methode in Abhängigkeit von der Temperatur ermittelt, wobei das Polymer mit der höheren Dichte, PEO, die Tropfenphase und PPO die Matrixphase bildet. Das Additiv wurde bei Messung der Grenzflächenspannung der ternären Systeme in unterschiedlichen Konzentrationen entweder einer oder beiden Homopolymerphasen zugegeben. Die Konzentrationsabhängigkeit von Sigma lässt sich sowohl mit dem Modell von Tang und Huang als auch mit einem Langmuir-analogen Ansatz gut beschreiben.Um den Zusammenhang zwischen sigma und dem Phasenverhalten zu untersuchen, wurden für einige der ternären Systeme Trübungskurven bei 100°C aufgenommen. Der Vergleich zwischen den Phasendiagrammen und den korrespondierenden Werten von sigma weist darauf hin, dass ein Additiv sigma gerade dann wirksam reduziert, wenn es einem Homopolymer zugefügt wird, mit dem es nur begrenzt verträglich ist, da dann die Triebkraft zur Anlagerung an der Grenzfläche besonders ausgeprägt ist. Das bereits bekannte Phänomen, wonach der Wert der Grenzflächenspannung davon abhängig sein kann, in welcher der Phasen das Additiv zu Beginn der Messung vorliegt, wurde ausführlich untersucht. Es wird angenommen, dass das System nicht in jedem Fall das thermodynamische Gleichgewicht erlangt und der beobachtete Effekt auf das Erreichen stationärer Zustände zurückzuführen ist. Dieses Verhalten kann mit einem Modell beschrieben werden, in welches das Viskositätsverhältnis der Homopolymere sowie der Verteilungskoeffizient des Copolymers zwischen den Homopolymerphasen eingehen. Aus Löslichkeitsparametern wurde der binäre Wechselwirkungsparameter Chi PEO/PPO = 0.18 abgeschätzt und mit diesem die theoretischen Werte für sigma zwischen PEO und PPO nach den Modellen von Roe bzw. Helfand und Tagami berechnet. Der Vergleich mit den experimentellen Daten des binären Systems zeigt, dass beide Ansätze sigma-Werte liefern, die in der Größenordnung der experimentellen Daten liegen, hierbei erweist sich der Ansatz von Roe als besonders geeignet. Die Temperaturabhängigkeit der Grenzflächenspannung wird jedoch durch beide Ansätze unzutreffend wiedergegeben. Mit dem Modell von Helfand und Tagami wurden eine Grenzflächendicke von 7.9 Å und das Dichteprofil der Grenzfläche berechnet. Für die Copolymere EO92PO56EO92 und S9EO22 (die Indices geben die Zahl der Monomereinheiten an) können die Grenzflächenüberschusskonzentrationen, die kritische Mizellenkonzentration sowie der einem Additivmolekül an der Grenzschicht zur Verfügung stehende Platz bestimmt werden.Der Vergleich unterschiedlicher Copolymere hinsichtlich ihrer Fähigkeit, sigma wirkungsvoll herabzusetzen, zeigt, dass im Fall von Triblockcopolymeren die Anordnung der Blöcke gegenüber der Zusammensetzung eine untergeordnete Rolle spielt. Mit zunehmender Kettenlänge nimmt die Effektivität als Compatibilizer sowohl bei Blockcopolymeren als auch bei statistischen Copolymeren zu.

Neuartige Polyelektrolytstrukturen auf der Basis von L-Lysin

In der vorliegenden Arbeit werden drei Polyelektrolyt-Architekturen zunehmender Verzweigung auf der Basis von L-Lysin vorgestellt. Zunächst wird auf das Aggregationsverhalten des linearen Blockpolyelektrolyten Polystyrol-b-Poly(L-Lysin) eingegangen. Dabei wird der Einfluss der Lysinblocklänge (NLys = 10…70) bei gleich bleibendem, sehr kurzem hydrophobem Polystyrolsegment untersucht. Wie sich der Polystyrolblock auf die Helixbildung auswirkt, kann mit Hilfe von Zirkulardichroismus nachgewiesen werden. Nach Bestimmung der kritischen Mizellenkonzentration über Fluoreszenzspektroskopie wird mittels statischer Streumethoden (SLS, SANS) eine zylinderförmige Mizelle mit einem Kernradius von 4,4 nm charakterisiert. Im zweiten Abschnitt werden die optischen Eigenschaften von sternförmigen, rot fluoreszierenden Perylendiimid-Poly(L-lysin)-Konjugaten mit variierender Armzahl (n = 4, 8, 16) und Kettenlänge (NLys = 10, 50, 100) beschrieben. Die guten Absorptionseigenschaften und schlechten Fluoreszenzeigenschaften zeigen weder eine Abhängigkeit von der Sekundärstruktur der Poly(L-lysin)-Arme noch von deren Zahl oder Kettenlänge. Der dritte Teil der Arbeit handelt von amin- (Fmoc-, TFAA- oder Z-) geschützten L-Lysindendrone bis zur dritten Generation, welche durch Verknüpfung der Carboxylfunktion der Dendrone mit der Amingruppe von Vinylbenzylamin in Makromonomere überführt werden. Das Polymerisationsverhalten der Makromonomere wird in Abhängigkeit der Dendrongeneration und der Monomerkonzentration zu Beginn der Polymerisation untersucht. Anhand von AFM-Aufnahmen kann nachgewiesen werden, dass das Polystyrolrückgrat der dendronisierten Polymere der ersten Z-geschützten Generation eine Streckung erfährt.

Hydrodynamic Characterization of Bile Salt Host-Guest Complexes by Pulsed Field Gradient NMR Spectroscopy

The work described herein is aimed at understanding primary and secondary aggregation of bile salt micelles and how micelles can perform chiral recognition of binapthyl analytes. Previous work with cholate and deoxycholate using micellar electrokinetic chromatography (MEKC) and nuclear magnetic resonance (NMR) has provided insightinto cholate and deoxycholate micelle formation, especially with respect to the critical micelle concentration (CMC). Chiral separations of the model analyte, 1,1â??-binaphthyl-2,2â??-diyl hydrogen phosphate (BNDHP), via cholate (C) and deoxycholate (DC) mediated MEKC separataions previously have shown the DC CMC to be 7-10 mM andthe cholate CMC at 14 mM at ph 12. A second model analyte,1,1â??-binaphthol (BN), was also previously investigated to probe micellar structure, but the MEKC data for this analyte implied a higher CMC, which may be interpreted as secondary aggregation. Thiswork extends the investigation of bile salts to include pulsed field gradient spin echo (PFGSE) NMR experiments being used to gain information about the size and degree of polydispersity of cholate and deoxycholate micelles. Concentrations of cholate below 10mM show a large variation in effective radius likely due to the existence of transient preliminary aggregates. The onset of the primary micelle shows a dramatic increase in effective radius of the micelle in cholate and deoxycholate. In the region of expectedsecondary aggregation a gradual increase of effective radius was observed with cholate; deoxycholate showed a persistent aggregate size in the secondary micelle region that is modulated by the presence of an analyte molecule. Effective radii of cholate anddeoxycholate (individually) were compared with and without R- and S-BNDHP in order to observe the effective radius difference of micelles with and without analyte present. The presence of S-BNDHP consistently resulted in a larger effective aggregate radius incholate and deoxycholate, confirming previous data of the S-BNDHP interacting more with the micelle than R-BNDHP. In total, various NMR techniques, like diffusion NMR can be used to gain a greater understanding of the bile salt micellization process and chiral resolution.

Self-assembling cannabinomimetics: supramolecular structures of N-alkyl amides

Certain fatty acid N-alkyl amides from the medicinal plant Echinacea activate cannabinoid type-2 (CB2) receptors. In this study we show that the CB2-binding Echinacea constituents dodeca-2E,4E-dienoic acid isobutylamide (1) and dodeca-2E,4E,8Z,10Z-tetraenoic acid isobutylamide (2) form micelles in aqueous medium. In contrast, micelle formation is not observed for undeca-2E-ene-8,10-diynoic acid isobutylamide (3), which does not bind to CB2, or structurally related endogenous cannabinoids, such as arachidonoyl ethanolamine (anandamide). The critical micelle concentration (CMC) range of 1 and 2 was determined by fluorescence spectroscopy as 200-300 and 7400-10000 nM, respectively. The size of premicelle aggregates, micelles, and supermicelles was studied by dynamic light scattering. Microscopy images show that compound 1, but not 2, forms globular and rod-like supermicelles with radii of approximately 75 nm. The self-assembling N-alkyl amides partition between themselves and the CB2 receptor, and aggregation of N-alkyl amides thus determines their in vitro pharmacological effects. Molecular mechanics by Monte Carlo simulations of the aggregation process support the experimental data, suggesting that both 1 and 2 can readily aggregate into premicelles, but only 1 spontaneously assembles into larger aggregates. These findings have important implications for biological studies with this class of compounds.

Characterization of a Coal Fly Ash-Cement Slurry by the Absolute Foam Index

This dissertation established a standard foam index: the absolute foam index test. This test characterized a wide range of coal fly ash by the absolute volume of air-entraining admixture (AEA) necessary to produce a 15-second metastable foam in a coal fly ash-cement slurry in a specified time. The absolute foam index test was used to characterize fly ash samples having loss on ignition (LOI) values that ranged from 0.17 to 23.3 %wt. The absolute foam index characterized the fly ash samples by absolute volume of AEA, defined as the amount of undiluted AEA solution added to obtain a 15-minute endpoint signified by 15-second metastable foam. Results were compared from several foam index test time trials that used different initial test concentrations to reach termination at selected times. Based on the coefficient of variation (CV), a 15-minute endpoint, with limits of 12 to 18 minutes was chosen. Various initial test concentrations were used to accomplish consistent contact times and concentration gradients for the 15-minute test endpoint for the fly ash samples. A set of four standard concentrations for the absolute foam index test were defined by regression analyses and a procedure simplifying the test process. The set of standard concentrations for the absolute foam index test was determined by analyzing experimental results of 80 tests on coal fly ashes with loss on ignition (LOI) values ranging from 0.39 to 23.3 wt.%. A regression analysis informed selection of four concentrations (2, 6, 10, and 15 vol.% AEA) that are expected to accommodate fly ashes with 0.39 to 23.3 wt.% LOI, depending on the AEA type. Higher concentrations should be used for high-LOI fly ash when necessary. A procedure developed using these standard concentrations is expected to require only 1-3 trials to meet specified endpoint criteria for most fly ashes. The AEA solution concentration that achieved the metastable foam in the foam index test was compared to the AEA equilibrium concentration obtained from the direct adsorption isotherm test with the same fly ash. The results showed that the AEA concentration that satisfied the absolute foam index test was much less than the equilibrium concentration. This indicated that the absolute foam index test was not at or near equilibrium. Rather, it was a dynamic test where the time of the test played an important role in the results. Even though the absolute foam index was not an equilibrium condition, a correlation was made between the absolute foam index and adsorption isotherms. Equilibrium isotherm equations obtained from direct isotherm tests were used to calculate the equilibrium concentrations and capacities of fly ash from 0.17 to 10.5% LOI. The results showed that the calculated fly ash capacity was much less than capacities obtained from isotherm tests that were conducted with higher initial concentrations. This indicated that the absolute foam index was not equilibrium. Rather, the test is dynamic where the time of the test played an important role in the results. Even though the absolute foam index was not an equilibrium condition, a correlation was made between the absolute foam index and adsorption isotherms for fly ash of 0.17 to 10.5% LOI. Several batches of mortars were mixed for the same fly ash type increasing only the AEA concentration (dosage) in each subsequent batch. Mortar air test results for each batch showed for each increase in AEA concentration, air contents increased until a point where the next increase in AEA concentration resulted in no increase in air content. This was maximum air content that could be achieved by the particular mortar system; the system reached its air capacity at the saturation limit. This concentration of AEA was compared to the critical micelle concentration (CMC) for the AEA and the absolute foam index.

Structures and Concentrations of Surfactants in Gut Fluid of the Marine Polychaete Arenicola Marina

Marine invertebrate deposit feeders secrete surfactants into their gut fluid in concentrations sufficient to induce micelle formation, enhancing solubilization of sedimentary lipids. We isolated and identified 3 related surfactant molecules from the deposit-feeding polychaete lugworm Arenicola marina. Surfactants were isolated and separated by a combination of solvent extraction and thin-layer and gas chromatography. Identification was performed using mass and infrared spectrometry, coupled to various derivatization and hydrolysis reactions. A. marina produces a mixture of related yet distinct anionic surfactants composed of branched, C9, saturated and unsaturated fatty acids that are amide linked to leucine or glycine residues, showing some similarity to crustacean surfactants. The critical micelle concentration of the mixture of these surfactants in gut fluid was about 2 mM, and total concentrations ranged from 5.5 to 19.5 mM. The hydrophilic amide linkage helps to explain previous observations that gut surfactants do not adsorb onto sediment transiting the gut.

MyoD forms micelles which can dissociate to form heterodimers with E47: implications of micellization on function.

MyoD is a member of a family of DNA-binding transcription factors that contain a helix-loop-helix (HLH) region involved in protein-protein interactions. In addition to self-association and DNA binding, MyoD associates with a number of other HLH-containing proteins, thereby modulating the strength and specificity of its DNA binding. Here, we examine the interactions of full-length MyoD with itself and with an HLH-containing peptide portion of an E2A gene product, E47-96. Analytical ultracentrifugation reveals that MyoD forms micelles that contain more than 100 monomers and are asymmetric and stable up to 36 degrees C. The critical micelle concentration increases slightly with temperature, but micelle size is unaffected. The micelles are in reversible equilibrium with monomer. Addition of E47-96 results in the stoichiometric formation of stable MyoD-E47-96 heterodimers and the depletion of micelles. Micelle formation effectively holds the concentration of free MyoD constant and equal to the critical micelle concentration. In the presence of micelles, the extent of all interactions involving free MyoD is independent of the total MyoD concentration and independent of one another. For DNA binding, the apparent relative specificity for different sites can be affected. In general, heterodimer-associated activities will depend on the self-association behavior of the partner protein.

Síntese e caracterização de nanomateriais superparamagnéticos do tipo core-shell para aplicação em catálise e biomedicina

As diversas aplicações tecnológicas de nanopartículas magnéticas (NPM) vêm intensificando o interesse por materiais com propriedades magnéticas diferenciadas, como magnetização de saturação (MS) intensificada e comportamento superparamagnético. Embora MNP metálicas de Fe, Co e bimetálicas de FeCo e FePt possuam altos valores de MS, sua baixa estabilidade química dificulta aplicações em escala nanométrica. Neste trabalho foram sintetizadas NPM de Fe, Co, FeCo e FePt com alta estabilidade química e rigoroso controle morfológico. NPM de óxido metálicos (Fe e Co) também foram obtidas. Dois métodos de síntese foram empregados. Usando método baseado em sistemas nanoheterogêneos (sistemas micelares ou de microemulsão inversa), foram sintetizadas NPM de Fe3O4 e Co metálico. Foram empregados surfactantes cátion-substituídos: dodecil sulfato de ferro(III) (FeDS) e dodecil sulfato de cobalto(II) (CoDS). Para a síntese das NPM, foram estudados e determinados a concentração micelar crítica do FeDS em 1-octanol (cmc = 0,90 mmol L-1) e o diagrama de fases pseudoternário para o sistema n-heptano/CoDS/n-butanol/H2O. NPM esferoidais de magnetita com3,4 nm de diâmetro e comportamento quase-paramagnético foram obtidas usando sistemas micelares de FeDS em 1-octanol. Já as NPM de Co obtidas via microemulsão inversa, apesar da larga distribuição de tamanho e baixa MS, são quimicamente estáveis e superparamagnéticas. O segundo método é baseado na decomposição térmica de complexos metálicos, pelo qual foram preparadas NPM esféricas de FePt e de óxidos metálicos (Fe3O4, FeXO1-X, (Co,Fe)XO1-X e CoFe2O4) com morfologia controlada e estabilidade química. O método não mostrou a mesma efetividade na síntese de NPM de FeAg e FeCo: a liga FeAg não foi obtida enquanto que NPM de FeCo com estabilidade química foram obtidas sem controle morfológico. NPM de Fe e FeCo foram preparadas a partir da redução térmica de NPM de Fe3O4 e CoFe2O4, as quais foram previamente recobertas com sílica. A sílica previne a sinterização inter-partículas, além de proporcionar caráter hidrofílico e biocompatibilidade ao material. As amostras reduzidas apresentaram aumento dos valores de MS (entre 21,3 e 163,9%), o qual é diretamente proporcional às dimensões das NPM. O recobrimento com sílica foi realizado via hidrólise de tetraetilortosilicato (TEOS) em sistema de microemulsão inversa. A espessura da camada de sílica foi controlada variando-se o tempo de reação e as concentrações de TEOS e de NPM, sendo então proposto um mecanismo do processo de recobrimento. Algumas amostras receberam um recobrimento adicional de TiO2 na fase anatase, para o qual foi empregado etilenoglicol como solvente e ligante para formação de glicolato de Ti como precursor. A espessura da camada de TiO2 (2-12 nm) é controlada variando as quantidades relativas entre NPM e o precursor de Ti. Ensaios de hipertermia magnética foram realizados para as amostras recobertas com sílica. Ensaios de hipertermia magnéticas mostram grande aumento da taxa de aquecimento das amostras após a redução térmica, mesmo para dispersões diluídas de NPM (0,6 a 4,5 mg mL-1). Taxas de aquecimento entre 0,3 e 3,0oC min-1 e SAR entre 37,2 e 96,3 W g-1. foram obtidos. A atividade fotocatalítica das amostras recobertas foram próximas à da fase anatase pura, com a vantagem de possuir um núcleo magnético que permite a recuperação do catalisador pela simples aplicação de campos magnéticos externos. Os resultados preliminares dos ensaios de hipertermia magnética e fotocatálise indicam um forte potencial dos materiais aqui relatados para aplicações em biomedicina e em fotocatálise.

Dodecyltrimethylammonium chloride adsorption at the silica/water interface studied by Sum Frequency Generation

La génération des fréquences somme (SFG), une technique spectroscopique spécifique aux interfaces, a été utilisée pour caractériser les changements de la structure macromoléculaire du surfactant cationique chlorure de dodécyltriméthylammonium (DTAC) à l’interface silice/eau dans une plage de pH variant entre 3 et 11. Les conditions expérimentales ont été choisies pour imiter les conditions les plus communes trouvées pendant les opérations de récupération assistée du pétrole. Particulièrement, la silice a été étudiée, car elle est un des composantes des surfaces minérales des réservoirs de grès, et l’adsorption du surfactant a été étudiée avec une force ionique pertinente pour les fluides de la fracturation hydraulique. Les spectres SFG ont présenté des pics détectables avec une amplitude croissante dans la région des étirements des groupes méthylène et méthyle lorsque le pH est diminué jusqu’à 3 ou augmenté jusqu’à 11, ce qui suggère des changements de la structure des agrégats de surfactant à l’interface silice/eau à une concentration de DTAC au-delà de la concentration micellaire critique. De plus, des changements dans l’intensité SFG ont été observés pour le spectre de l’eau quand la concentration de DTAC augmente de 0,2 à 50 mM dans les conditions acide, neutre et alcaline. À pH 3, près du point de charge zéro de la surface de silice, l’excès de charge positive en raison de l’adsorption du surfactant cationique crée un champ électrostatique qui oriente les molécules d’eau à l’interface. À pH 7 et 11, ce qui sont des valeurs au-dessus du point de charge zéro de la surface de silice, le champ électrostatique négatif à l’interface silice/eau diminue par un ordre de grandeur avec l’adsorption du surfactant comme résultat de la compensation de la charge négative à la surface par la charge positive du DTAC. Les résultats SFG ont été corrélés avec des mesures de l’angle de contact et de la tension interfaciale à pH 3, 7 et 11.

Dodecyltrimethylammonium chloride adsorption at the silica/water interface studied by Sum Frequency Generation

La génération des fréquences somme (SFG), une technique spectroscopique spécifique aux interfaces, a été utilisée pour caractériser les changements de la structure macromoléculaire du surfactant cationique chlorure de dodécyltriméthylammonium (DTAC) à l’interface silice/eau dans une plage de pH variant entre 3 et 11. Les conditions expérimentales ont été choisies pour imiter les conditions les plus communes trouvées pendant les opérations de récupération assistée du pétrole. Particulièrement, la silice a été étudiée, car elle est un des composantes des surfaces minérales des réservoirs de grès, et l’adsorption du surfactant a été étudiée avec une force ionique pertinente pour les fluides de la fracturation hydraulique. Les spectres SFG ont présenté des pics détectables avec une amplitude croissante dans la région des étirements des groupes méthylène et méthyle lorsque le pH est diminué jusqu’à 3 ou augmenté jusqu’à 11, ce qui suggère des changements de la structure des agrégats de surfactant à l’interface silice/eau à une concentration de DTAC au-delà de la concentration micellaire critique. De plus, des changements dans l’intensité SFG ont été observés pour le spectre de l’eau quand la concentration de DTAC augmente de 0,2 à 50 mM dans les conditions acide, neutre et alcaline. À pH 3, près du point de charge zéro de la surface de silice, l’excès de charge positive en raison de l’adsorption du surfactant cationique crée un champ électrostatique qui oriente les molécules d’eau à l’interface. À pH 7 et 11, ce qui sont des valeurs au-dessus du point de charge zéro de la surface de silice, le champ électrostatique négatif à l’interface silice/eau diminue par un ordre de grandeur avec l’adsorption du surfactant comme résultat de la compensation de la charge négative à la surface par la charge positive du DTAC. Les résultats SFG ont été corrélés avec des mesures de l’angle de contact et de la tension interfaciale à pH 3, 7 et 11.

Sorption characteristics of a nonionic surfactant during remediation of contaminated soil with different organic content

Surfactant enhanced subsurface remediation has gained importance in soil remediation. Since surfactants can be sorbed on soils, the concentration of free surfactant could drop below the critical micelle concentration, CMC, which may reduce the ability of the surfactant to solubilize the contaminants in soils. ^ The main goal of this research was to study the factors affecting the surfactant sorption on soil such as surfactant concentration, soil organic content, and organic contaminants in soil and to determine the organic contaminants removed from soils by surfactant. The results would be served as the basis for the implementation of a future study in the pilot scale and field scale for surfactant enhanced subsurface remediation. ^ This research study investigated the relationship between the organic content of soils and the sorption characteristics of a nonionic surfactant, Triton X-100. The experiments were performed using uncontaminated soils and soil contaminated with naphthalene and decane. The first part of the experiments were conducted in batch mode utilizing surface tension technique to determine the CMC of surfactant Triton X-100 and the effective CMC in the soil/aqueous system. The sorption of Triton X-100 was calculated from the surface tension measurements. The second part of the experiments utilized the SPME/GC/FID technique to determine the concentration of the contaminants solubilized from the soils by the surfactant Triton X-100 at different concentrations. ^ The results indicated that when the concentration of surfactant was lower than the CMC, the amount of surfactant sorbed on soil increased with the increasing surfactant concentration and the surfactant sorption characteristics of the uncontaminated soils could be modeled by the Freundlich isotherm. For the contaminated soils, the amount of surfactant sorbed was higher than those for the uncontaminated soils. The amount of surfactant sorbed on soils also depends on the organic content in the soils. The higher the organic content in the soil, higher is the amount of surfactant sorbed onto the soil. When the concentration of surfactant was higher than the CMC, the amount of surfactant added into the soil/aqueous system will increase the number of micelle and it increase the solubilization of organic contaminant from the soils. The ratio of the moles of organic contaminant solubilized to the moles of surfactant present as micelles is called the molar solubilization ratio (MSR). MSR value for naphthalene was about 0.16 for the soil-water systems. The organic content of soil did not appear to affect MSR for naphthalene. On the other hand, the MSR values for decane were 0.52, 0.39 and 0.38 for soils with 25%, 50% and 75% organic content, respectively. ^

Avaliação da influência de surfactantes químico e biológico na hidrólise enzimática de casca de coco verde após pré-tratamento ácido/alcalino e com peróxido de hidrogênio alcalino

In Brazil many types of bioproducts and agroindustrial waste are generated currently, such as cacashew apple bagasse and coconut husk, for example. The final disposal of these wastes causes serious environmental issues. In this sense, waste lignocellulosic content, as the shell of the coconut is a renewable and abundant raw material in which its use has an increased interest mainly for the 2nd generation ethanol production. The hydrolysis of cellulose to reducing sugars such as glucose and xylose is catalysed by a group of enzymes called cellulases. However, the main bottleneck in the enzymatic hydrolysis of cellulose is the significant deactivation of the enzyme that shows irreversible adsorption mechanism leading to reduction of the cellulose adsorption onto cellulose. Studies have shown that the use of surfactants can modify the surface property of the cellulose therefore minimizing the irreversible binding. The main objective of the present study was to evaluate the influence of chemical and biological surfactants during the hydrolysis of coconut husk which was subjected to two pre-treatment in order to improve the accessibility of the enzymes to the cellulose, removing this way, part of the lignin and hemicellulose present in the structure of the material. The pre-treatments applied to coconut bagasse were: Acid/Alkaline using 0.6M H2SO4 followed by 1M NaOH, and the one with Alkaline Hydrogen Peroxide at a concentration of 7.35% (v/v) and pH 11.5. Both the material no treatment and pretreated were characterized using analysis of diffraction X-ray (XRD), Scanning Electron Microscopy (SEM) and methods established by NREL. The influence of both surfactants, chemical and biological, was used at concentrations below the critical micelle concentration (CMC), and the concentrations equal to the CMC. The application of pre-treatment with coconut residue was efficient for the conversion to glucose, as well as for the production of total reducing sugars, it was possible to observe that the pretreatment fragmented the structure as well as disordered the fibers. Regarding XRD analysis, a significant increase in crystallinity index was observed for pretreated bagasse acid/alkali (51.1%) compared to the no treatment (31.7%), while that for that treated with PHA, the crystallinity index was slightly lower, around 29%. In terms of total reducing sugars it was not possible to observe a significant difference between the hydrolysis carried out without the use of surfactant compared to the addition of Triton and rhamnolipid. However, by observing the conversions achieved during the hydrolysis, it was noted that the best conversion was using the rhamnolipíd for the husk pretreated with acid/alkali, reaching a value of 33%, whereas using Triton the higher conversion was 23.8%. The coconut husk is a residue which can present a high potential to the 2nd generation ethanol production, being the rhamonolipid a very efficient biosurfactant for use as an adjuvant in the enzymatic process in order to act on the material structure reducing its recalcitrance and therefore improving the conditions of access for enzymes to the substrate increasing thus the conversion of cellulose to glucose.

Avaliação da influência de surfactantes químico e biológico na hidrólise enzimática de casca de coco verde após pré-tratamento ácido/alcalino e com peróxido de hidrogênio alcalino

In Brazil many types of bioproducts and agroindustrial waste are generated currently, such as cacashew apple bagasse and coconut husk, for example. The final disposal of these wastes causes serious environmental issues. In this sense, waste lignocellulosic content, as the shell of the coconut is a renewable and abundant raw material in which its use has an increased interest mainly for the 2nd generation ethanol production. The hydrolysis of cellulose to reducing sugars such as glucose and xylose is catalysed by a group of enzymes called cellulases. However, the main bottleneck in the enzymatic hydrolysis of cellulose is the significant deactivation of the enzyme that shows irreversible adsorption mechanism leading to reduction of the cellulose adsorption onto cellulose. Studies have shown that the use of surfactants can modify the surface property of the cellulose therefore minimizing the irreversible binding. The main objective of the present study was to evaluate the influence of chemical and biological surfactants during the hydrolysis of coconut husk which was subjected to two pre-treatment in order to improve the accessibility of the enzymes to the cellulose, removing this way, part of the lignin and hemicellulose present in the structure of the material. The pre-treatments applied to coconut bagasse were: Acid/Alkaline using 0.6M H2SO4 followed by 1M NaOH, and the one with Alkaline Hydrogen Peroxide at a concentration of 7.35% (v/v) and pH 11.5. Both the material no treatment and pretreated were characterized using analysis of diffraction X-ray (XRD), Scanning Electron Microscopy (SEM) and methods established by NREL. The influence of both surfactants, chemical and biological, was used at concentrations below the critical micelle concentration (CMC), and the concentrations equal to the CMC. The application of pre-treatment with coconut residue was efficient for the conversion to glucose, as well as for the production of total reducing sugars, it was possible to observe that the pretreatment fragmented the structure as well as disordered the fibers. Regarding XRD analysis, a significant increase in crystallinity index was observed for pretreated bagasse acid/alkali (51.1%) compared to the no treatment (31.7%), while that for that treated with PHA, the crystallinity index was slightly lower, around 29%. In terms of total reducing sugars it was not possible to observe a significant difference between the hydrolysis carried out without the use of surfactant compared to the addition of Triton and rhamnolipid. However, by observing the conversions achieved during the hydrolysis, it was noted that the best conversion was using the rhamnolipíd for the husk pretreated with acid/alkali, reaching a value of 33%, whereas using Triton the higher conversion was 23.8%. The coconut husk is a residue which can present a high potential to the 2nd generation ethanol production, being the rhamonolipid a very efficient biosurfactant for use as an adjuvant in the enzymatic process in order to act on the material structure reducing its recalcitrance and therefore improving the conditions of access for enzymes to the substrate increasing thus the conversion of cellulose to glucose.

Age gelation of UHT milk - A review

Gelation of UHT milk during storage (age gelation) is a major factor limiting its shelf-life. The gel which forms is a three-dimensional protein matrix initiated by interactions between the whey protein beta -lactoglobulin and the kappa -casein of the casein micelle during the high heat treatment. These interactions lead to the formation of a beta -lactoglobulin-kappa -casein complex (beta kappa -complex). A feasible mechanism of age gelation is based on a two-step process; in the first step, the beta kappa -complexes dissociate from the casein micelles due to the breakdown of multiple anchor sites on kappa -casein, and in the second step, these complexes aggregate into a three-dimensional matrix. When a critical volume concentration of the beta kappa -complex is attained, a gel of custard-like consistency is formed. Significant factors which influence the onset of gelation include the nature of the heat treatment, proteolysis during storage, milk composition and quality, seasonal milk production factors and storage temperature. In this review, age gelation is discussed in terms of these factors, causative mechanisms and procedures for controlling it.

Formação de micelas mistas entre o sal biliar colato de sódio e o surfactante aniônico dodecanoato de sódio

Mixed-micelle formation between sodium chlolate (NaC) and the anionic surfactant sodium dodecanoate (SDoD) in Tris-HCl buffer solutions, pH 9.00, varying the molar fraction of the surfactants, was investigated by means of electrical conductivity and steady-state fluorescence of pyrene. The critical micelar concentration (cmc) was measured from the equivalent conductance versus the square root of the molar surfactant concentration plots and the regular solution theory (RST) was used to predict the mixing behavior. The I1/I3 pyrene ratio-surfactant concentration plots were used as an additional technique to follow the behavior and the changes in the micropolarity of the mixed micelles.