Three-phase computations of the continuous casting process

In this paper, the continuous casting process for steel slab production is modelled using a mult-physics approach. For this purpose, a Finite Volume (FV) numerical model was constructed in 3D, with the following characteristics: Time dependent, turbulent fluid flow and heat transfer in the molten steel and flux regions, solidification of the skin layer, under prescribed heat loss boundary conditions, particle tracking simulation of argon bubbles injected with the metal into the mould, full coupling between bubbles and liquid through buoyancy and interfacial forces using a novel gas accumulation technique, and a full transient simulation of flux-metal interface behaviour under the influence of gravity and fluid inertial forces and bubble plume buoyancy. The unstructure mesh FV code PHYSICA developed at Greenwich was used for carry out the simulations with physical process data and properties supplied by IRSID SA.

The tilt casting of titanium aluminides

TiAl castings are prone to various defects including bubbles entrained during the turbulent filling of moulds. The present research has exploited the principles of the Durville tilt casting technique to develop a novel process in which the Induction Skull Melting (ISM) of TiAl alloys in a vacuum chamber has been combined with controlled tilt pouring to achieve the tranquil transfer of the metal into a hot ceramic shell mould. Practical casting equipment has been developed to evaluate the feasibility of this process in parallel with the development of novel software to simulate and optimize it. The PHYSICA CFD code was used to simulate the filling, heat transfer and solidification during tilt pouring using a number of free surface modelling techniques, including the novel Counter Diffusion Method (CDM). In view of the limited superheat, particular attention was paid to the mould design to minimize heat loss and gas entrainment caused by interaction between the counter-flowing metal and gas streams. The model has been validated against real-time X-ray movies of the tilt casting of aluminium and against TiAl blade castings. Modelling has contributed to designing a mould to promote progressive filling of the casting and has led to the use of a parabolic tilting cycle to balance the competing requirements for rapid filling to minimize the loss of superheat and slow filling minimize the turbulence-induced defects.

Modelling the tilt-casting process for the tranquil filling of titanium alloy turbine blades

The tilt-casting method is used to achieve tranquil filling of gamma-TiAl turbine blades. The reactive alloy is melted in a cold crucible using an induction coil and then the complete crucible-mould- running system assembly is rotated through 180degrees to transfer the metal into the mould. The induction current is ramped down gradually as the rotation starts and the mould is preheated to maintain superheat. The liquid metal then enters the mould and the gas within it (argon) escapes through the inlet aperture and through auxiliary vents. Solidification starts as soon the metal enters the mould and it is important to account for this effect to predict and prevent misruns. The rotation rate has to be controlled carefully to allow sufficient time for gas evacuation, but at the same time preserve superheat. This 3-phase system is modelled using the FV method, with a fast implicit numerical scheme used to capture the transient liquid free surface. The enthalpy method is used to model solidification and predict defects such as trapped bubbles, macro-porosity or surface connected porosity. Modeling is used to support an experimental program for the development of a production method for gamma-TiAl blades, with a target length of 40cm. The experiments provide validation for the model and the model in turn optimizes the tilt-casting process. The work is part of the EU project IMPRESS.

The Technology of Copper Alloys, Particularly Leaded Bronze, in Greece, its Colonies, and in Etruria during the Iron Age

L’objet de la présente étude est le développement, l’application et la diffusion de la technologie associée à divers types d’alliages de cuivre, en particulier l’alliage du plomb-bronze, en Grèce ancienne, dans ses colonies, ainsi qu’en Étrurie. Le plomb-bronze est un mélange de diverses proportions d’étain, de cuivre et de plomb. Le consensus général chez les archéométallurgistes est que le plomb-bronze n’était pas communément utilisé en Grèce avant la période hellénistique; par conséquent, cet alliage a reçu très peu d’attention dans les documents d’archéologie. Cependant, les analyses métallographiques ont prouvé que les objets composés de plomb ajouté au bronze ont connu une distribution étendue. Ces analyses ont aussi permis de différencier la composition des alliages utilisés dans la fabrication de divers types de bronzes, une preuve tangible que les métallurgistes faisaient la distinction entre les propriétés du bronze d’étain et celles du plomb-bronze. La connaissance de leurs différentes caractéristiques de travail permettait aux travailleurs du bronze de choisir, dans bien des cas, l’alliage approprié pour une utilisation particulière. L’influence des pratiques métallurgiques du Proche-Orient a produit des variations tant dans les formes artistiques que dans les compositions des alliages de bronze grecs durant les périodes géométrique tardive et orientalisante. L’utilisation du plomb-bronze dans des types particuliers d’objets coulés montre une tendance à la hausse à partir de la période orientalisante, culminant dans la période hellénistique tardive, lorsque le bronze à teneur élevée en plomb est devenu un alliage commun. La présente étude analyse les données métallographiques de la catégorie des objets coulés en bronze et en plomb-bronze. Elle démontre que, bien que l’utilisation du plomb-bronze n’était pas aussi commune que celle du bronze d’étain, il s’agissait néanmoins d’un mélange important d’anciennes pratiques métallurgiques. Les ères couvertes sont comprises entre les périodes géométrique et hellénistique.

Casting yield improvement in graphite iron castings

A well designed runner and feeding system should produce castings with minimal defects and low pour weight. This thesis investigates how the filling regime and solidification of the mould influences defects in the castings produced from that mould. Design guidelines to reduce such defects are proposed and tested. An existing shrinkage fault in a Grey Iron disc brake casting is simulated using a commercial finite-difference computer program. Three criteria are used to predict the defect and the effect of changes to the feeder geometry. Critical Fraction Solidification analysis is used to determine whether the feeder remains in liquid contact with the casting during solidification and this approach is shown to correctly predict the presence or absence of porosity* The feeder block is extended below the ingate of the casting to improve liquid contact between the casting and feeder without significantly increasing the feeder mass. Plant trials confirm the change to the feeder eliminates the porosity defect. The runner system and mould venting for a thin walled Ductile Iron casting are investigated. Trials show that by setting the total mould vent area to be greater than the net ingate area of the castings, the cold-shut frequency is halved. A method for runner system design based on peak linear flow velocity in the runner during mould filling is proposed. A new pressurised runner system produces castings with significantly fewer defects and reduced pour weight when runner areas are designed to maintain peak velocity below 1 m/s. Peak velocity and magnesium levels are demonstrated to be critical factors in the elimination of cold-shut defects. A pressurised runner system is also shown to isolate inclusion defects from castings more effectively than an unpressurised system. From this work, a technique is proposed which allows the yield of an existing runner and feeder system for iron castings to be improved with confidence in the results.

Recrystallization kinetic behavior of copper-bearing strip cast steel

In the present study, copper-bearing low carbon steels were produced by direct strip casting (DSC) method on a pilot scale. The effects of copper on mechanical, microstructural, and recrystallization behavior were investigated. As-cast microstructure mainly consists of polygonal ferrite and Widmanstatten ferrite. The increase in Cu increases the amount of Widmanstatten ferrite and induces the formation of bainite in the as-cast condition. It was found that copper increases strength and hardness by solid solution strengthening, grain refinement, and precipitation hardening and the increment is significant above 1% Cu in as-cast condition. Six different compositions were selected for recrystallization study. All the samples were cold rolled to 70% reduction and annealed at three different temperatures, 600, 650, and 700°C for various times. Recrystallization responses were strongly dependent on initial microstructure and Cu content and the effect is dramatic between 1 and 2% Cu. Recrystallization time and temperature were found to be increased with increase in copper content.

Metallurgical evaluation of a copper-based alloy for dental castings.

The present study was designed to evaluate the metallurgical properties of an experimental, low-cost copper-zinc-aluminum-nickel alloy for dental castings. Some specimens were subjected to heat treatment after induction casting. The extent of corrosion was determined by measuring weight loss of specimens stored in a sodium sulfite solution. In the as-cast specimens, tests demonstrated the presence of three phases: the first consisted of copper-zinc-aluminum, the second was similar but lower in copper and aluminum, and the third consisted of an intermetallic compound of manganese-nickel-phosphorus. After heat treatment, the first phase remained relatively constant, the second was converted to Cu3Al, and the third increased in volume. The weight loss from the as-cast specimens was eight times that of the heat-treated specimens. It was concluded that the heat treatment substantially changed the microstructure and improved the corrosion resistance of the experimental alloy.

Novo formato de pilar protético em zircônia estabilizada por Itría (Y-Tzp) para implantodontia desenvolvido pela técnica de slip casting

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Texture analysis of cold rolled and annealed aluminum alloy produced by twin-roll casting

A 7.4 mm thick strip of 3003 aluminum alloy produced by the industrial twin-roll casting (TRC) process was homogenized at 500 °C for 12 hours, after which it was cold rolled in two conditions: 1) to reduce the strip's thickness by 67%, and 2) to reduce it by 91%. The alloy was annealed at 400 °C for 1 hour in both conditions. The results revealed that a rotated cube texture, the {001}<110> component, predominated in the as-cast condition and was transformed into brass, copper and S type textures during the cold rolling process. There was practically no difference between the deformation textures at the two thickness reductions.

Observation of crack initiation during hot tearing

While the general mechanisms of hot tearing are understood, i.e. the inability of liquid to feed imposed strain on the mushy material, work continues on improving the understanding of the mechanisms at play. A hot tear test rig that measures the temperature and load imposed on the mushy zone during solidification has been successfully used to study hot tearing. The mould has now been modified to incorporate a window above the hot spot region to allow observation of hot tear formation and growth. Combining information from visual observation with load and temperature data has led to a better understanding of the mechanism of hot tearing. Tests were carried out on an Al-0.5 wt-% Cu alloy. It was found that load development began at about 90% solid and a hot tear formed a short time later, at between 93% and 96% solid. Hot tearing started at a very low load.

A three dimensional finite volume approach to the thermo-mechanical modelling of the shape casting of metals

This paper presents a three dimensional, thermos-mechanical modelling approach to the cooling and solidification phases associated with the shape casting of metals ei. Die, sand and investment casting. Novel vortex-based Finite Volume (FV) methods are described and employed with regard to the small strain, non-linear Computational Solid Mechanics (CSM) capabilities required to model shape casting. The CSM capabilities include the non-linear material phenomena of creep and thermo-elasto-visco-plasticity at high temperatures and thermo-elasto-visco-plasticity at low temperatures and also multi body deformable contact with which can occur between the metal casting of the mould. The vortex-based FV methods, which can be readily applied to unstructured meshes, are included within a comprehensive FV modelling framework, PHYSICA. The additional heat transfer, by conduction and convection, filling, porosity and solidification algorithms existing within PHYSICA for the complete modelling of all shape casting process employ cell-centred FV methods. The termo-mechanical coupling is performed in a staggered incremental fashion, which addresses the possible gap formation between the component and the mould, and is ultimately validated against a variety of shape casting benchmarks.

Modelling interacting phenomena during the solidification of metals in the casting process

A variety of interacting complex phenomena takes place during the casting of metallic components. Here molten metal is poured into a mould cavity where it flows, cools, solidifies and then deforms in its solid state. As the metal cools, thermal gradients will promote thermal convection which will redistribute the heat around the component (usually from feeders or risers) towards the solidification front and mushy zone. Also, as the evolving solid regions of the cast component deform they will form gap at the cast-mould interface. This gap may change the rate of solidification in certain parts the casting, hence affecting the manner in which the cast component solidifies. Interaction between a cast component and its surrounding mould will also govern stress magnitudes in both the cast and mould -these may lead to defects such as cracks. This paper presents a multiphysics modelling approach to this complex process. Emphasis will be placed on the interacting phenomena taking place during the process and the modelling strategy used. Comparisons with plant data are also be given.

Experimental studies on comparison of microwave curing and thermal curing of epoxy resins used for alternative mould materials

In this present work attempts have been made to study the glass transition temperature of alternative mould materials by using both microwave heating and conventional oven heating. In this present work three epoxy resins, namely R2512, R2515 and R2516, which are commonly used for making injection moulds have been used in combination with two hardeners H2403 and H2409. The magnetron microwave generator used in this research is operating at a frequency of 2.45 GHz with a hollow rectangular waveguide. In order to distinguish the effects between the microwave and conventional heating, a number of experiments were performed to test their mechanical properties such as tensile and flexural strengths. Additionally, differential scanning calorimeter technique was implemented to measure the glass transition temperature on both microwave and conventional heating. This study provided necessary evidences to establish that microwave heated mould materials resulted with higher glass transition temperature than the conventional heating. Finally, attempts were also made to study the microstructure of microwave-cured materials by using a scanning electron microscope in order to analyze the morphology of cured specimens.