Formation, Thermal Stability and Deformation Behavior of Graphite-Flakes Reinforced Cu-based Bulk Metallic Glass Matrix Composites

Graphite-flake reinforced Cu47Ti34Zr11 Ni-8 bulk metallic glass matrix composite was fabricated by water-cooled copper mould cast. Most of the graphite flakes still keep unreacted and distribute uniformly in the amorphous matrix except that some reactive wetting occurs by the formation of TiC particles around the flakes. It reveals that the presence of graphite flakes does not affect the onset of the glass transition temperature, crystallization reaction and liquidus of the metallic glass. The resulting material shows obvious serrated flow and higher fracture strength under room temperature compressive load, comparing with the monolithic bulk metallic glass (BMG). Three types of interaction between the shear bands and graphite flakes, namely, shear band termination, shear bands branching and new shear bands formation near the graphite flakes can be observed by quasi-static uniaxial compression test and bonded interface technique through Vickers indentation.

Kinetics of Glass Transition and Crystallization in Carbon Nanotube Reinforced Mg-Cu-Gd Bulk Metallic Glass

Mg65 Cu25 Gdlo bulk metallic glass and its carbon nanotube reinforced composite were prepared. Differential scanning calorimeter (DSC) was used to investigate the kinetics of glass transition and crystallization processes. The influence of CNTs addition to the glass matrix on the glass transition and crystallization kinetics was studied. It is shown that the kinetic effect on glass transition and crystallization are preserved for both the monothetic glass and its glass composite. Adding CNTs in to the glass matrix reduces the influence of the heating rate on the crystallization process. In addition, the CNTs increase the energetic barrier for the glass transition. This results in the decrease of GFA . The mechanism of the GFA decrease was also discussed.

Microstructure and mechanical properties of Zr-Cu-Al bulk metallic glasses

Zr49Cu46Al5 and Zr48.5Cu46.5Al5 bulk metallic glasses(BMGs) with diameter of 5 mm were prepared through water-cooled copper mold casting. The phase structures of the two alloys were identified by X-ray diffractometry(XRD). The thermal stability was examined by differential scanning calorimetry(DSC). Zr49Cu46Al5 alloy shows a glass transition temperature, T, of about 689 K, an crystallization temperature, T-x, of about 736 K. The Zr48.5Cu46.5Al5 alloy shows no obvious exothermic peak. The microstructure of the as-cast alloys was analyzed by transmission electron microscopy(TEM). The aggregations of CuZr and CuZr2 nanocrystals with grain size of about 20 nm are observed in Zr49Cu46Al5 nanocrystalline composite, while the Zr48.5Cu46.5Al5 alloy containing many CuZr martensite plates is crystallized seriously. Mechanical properties of bulk Zr49Cu46Al5 nanocrystalline composite and Zr48.5Cu46.5Al5 alloy measured by compression tests at room temperature show that the work hardening ability of Zr48.5Cu46.5Al5 alloy is larger than that of Zr48.5Cu46.5Al5 alloy.

Practical vortex diodes from pinning enhanced YBa2 Cu 3 O7-δ

We identify a scalable, practical route to fabricating a superconducting diode. The device relies for its function on the barrier to flux vortex entry being reduced at the substrate interface of a superconducting pinning enhanced YBa2 Cu3 O7-δ nanocomposite film. We show that these composite systems provide a practical route to fabricating a useful superconducting diode and demonstrate the rectification of an alternating current. © 2009 American Institute of Physics.

Fabrication of large grain Nd-Ba-Cu-O by seeded melt growth

Large, single grain Nd-Ba-Cu-O (NdBCO) composite samples of NdBa2Cu3O7-δ (Nd-123) containing 15 and 20 mol. % non-superconducting Nd4Ba2Cu2O10 (Nd-422) phase inclusions have been fabricated successfully by a variety of techniques based on top-seeded melt growth under reduced oxygen partial pressure. Specifically, individual grains up to 2cm in diameter have been grown using (100) oriented MgO seeding, self (NdBCO) seeding at elevated temperature and self-seeding of Ag and Au doped precursor pellets. The latter exhibit a reduced peritectic decomposition temperature compared with the undoped compound. These techniques, which vary in degree of difficulty and hence reliability, yield grains with a range of microstructural homogeneity. This paper describes the general aspects of large NdBCO grain fabrication and presents the results of the different fabrication techniques.

Large single grain (RE)-Ba-Cu-O superconductors with nano-phase inclusions

Nano-phase (5-20 nm) particles of YBa2(Cu0.5M 0.6)O6 [where M = Nb, Ta, Mo, W, Zr and Hf] have been introduced successfully into RE-Ba-Cu-O single grain superconductors. A study to enlarge the size of a single grain containing these particles has been carried out involving measurement of the growth rate as a function of YBa 2(Cu0.5M0.6)O6 phase concentration and degree of un-dercooling. The influence of the change in YBa2 (Cu0.8M0.5)O6 concentration on microstructural features is also investigated and the superconducting properties of these large grain superconductors are presented. © 2005 IEEE.

Microstructure and superconducting properties of single grains of Y-Ba-Cu-O containing Y-2411(M) and Y2O3

Y-Ba-Cu-O (YBCO) single grains have the potential to generate large trapped magnetic fields for engineering applications, and research on the processing and properties of this material has attracted interest world-wide over the past 20 years. In particular, the introduction of flux pinning centers to the large grain microstructure to improve its current density Jc, and hence trapped field, has been investigated extensively. Y2Ba 4CuMO2 [Y-2411(M)], where M = Nb, Ta, Mo, W, Ru, Zr, Bi and Ag, has been discovered recently to form very effective flux pinning centers due primarily to its ability to form nano-size inclusions in the superconducting phase matrix. However, the addition of the Y-2411(M) phase to the precursor composition complicates the melt-processing of single grains. The addition of Y2O3 to the precursor composition, however, broadens the growth window of single YBCO grains containing Y-2411 (M). We report an investigation of the microstructures and superconducting properties of single grains of this composition grown by top seeded melt growth (TSMG). © 2010 IEEE.

Electrical properties of LiNbO3 (electrolyte)/Cu (anode) bi-layers

In this work specific film structures of Li-Nb-O/Li/Li-Nb-O are investigated by AC Impedance Spectroscopy measurements at different temperatures. This gives the opportunity to investigate properties of the material itself and, at the same time, to consider the influence of the grain boundaries on the ionic behavior of the polycrystalline Lithium Niobate. On the other hand, LiNbO3/Li/Cu multi-layers are studied as electrolyte/anode bi-layers and potential parts of "Li-free" microbatteries. The Li deficiency in the as deposited Li-Nb-O films is cured by forming a "sandwich" of Li-Nb-O/Li/Li-Nb-O, which after annealing becomes ionic conductor. The electrical behavior of an annealed film depends on two sources. The first is due to properties of the material itself and the second is based on the network of the grain boundaries. The average size of the grains is strongly influenced by the structure of the ohmic-contact/substrate. The electrical behavior of the electrolyte/anode interface of the "Li-free" structure LiNbO3/Li/Cu/Au is very similar to the impedance measurements of the single LiNbO3 single films. The whole multilayer structure, though, presents a third relaxation time which is consistent of a small resistance. This resistance is independent of temperature and it seems that is due to the metallic interface Li/Cu/Au. © 2010 Elsevier B.V. All rights reserved.

Synthesis Gas Generation by Chemical-Looping Reforming Using Ce-Based Oxygen Carriers Modified with Fe, Cu, and Mn Oxides

Chemical-looping reforming (CLR) is a technology that can be used for partial oxidation and steam reforming of hydrocarbon fuels. It involves the use of a metal oxide as an oxygen carrier, which transfers oxygen from combustion air to the fuel. Composite oxygen carriers of cerium oxide added with Fe, Cu, and Mn oxides were prepared by co-precipitation and investigated in a thermogravimetric analyzer and a fixed-bed reactor using methane as fuel and air as oxidizing gas. It was revealed that the addition of transition-metal oxides into cerium oxide can improve the reactivity of the Ce-based oxygen carrier. The three kinds of mixed oxides showed high CO and H-2 selectivity at above 800 degrees C. As for the Ce-Fe-O oxygen carrier, methane was converted to synthesis gas at a H-2/CO molar ratio close to 2:1 at a temperature of 800-900 degrees C; however, the methane thermolysis reaction was found on Ce-Cu-O and Ce-Mn-O oxygen carriers at 850-900 degrees C. Among the three kinds of oxygen carriers, Ce-Fe-O presented the best performance for methane CLR. On Ce-Fe-O oxygen carriers, the CO and H-2 selectivity decreased as the Fe content increased in the carrier particles. An optimal range of the Ce/Fe molar ratio is Ce/Fe > 1 for Ce-Fe-O oxygen carriers. Scanning electron microscopy (SEM) analysis revealed that the microstructure of the Ce-Fe-O oxides was not dramatically changed before and after 20 cyclic reactions. A small amount of Fe3C was found in the reacted Ce-Fe-O oxides by X-ray diffraction (XRD) analysis.

Chitosan(Chitin)/Cellulose Composite Biosorbents Prepared Using Ionic Liquid for Heavy Metal Ions Adsorption

Chitosan(chitin)/cellulose composites as biodegradable biosorbents were prepared under an environment-friendly preparation processes using ionic liquids. Infrared and X-ray photoelectron spectra indicated the stronger intermolecular hydrogen bond between chitosan and cellulose, and the hydroxyl and amine groups were believed to be the metal ion binding sites. Among the prepared biosorbents, freeze-dried composite had higher adsorption capacity and better stability. The capacity of adsorption was found to be Cu(II) (0.417 mmol/g) > Zn(II) (0.303 mmol/g) > Cr(VI) (0.251 mmol/g) > Ni(II) (0.225 mmol/g) > Ph(II) (0.127 mmol/g) at the same initial concentration 5 mmol L-1. In contrast to some other chitosan-type biosorbents, preparation and component of the biosorbent were obviously more environment friendly. Moreover, adsorption capacity of chitosan in the blending biosorbent could be fully shown.

Hydrothermal synthesis and structural characterization of a novel organic-inorganic hybrid compound {[Cu(2, 2 '-bpy)(2)](2)-Mo8O26}

A novel organic-inorganic hybrid compound {[Cu (2, 2'-bpy)(2)](2)Mo8O26} has been hydrothermally Synthesized and structurally characterized by single-crystal X-ray diffraction. The compound crystallizes in the orthorhombic space group, Pna2(1), with a=2.4164 (5), b=1.8281 (4), c=1.1877 (2) nm, V=5.247(2) nm(3), Z=4, and final R-1=0.0331, wR(2)=0.0727. The structure consists of discrete {[Cu(2,2'-bpy)(2)](2)Mo8O26} clusters, constructed from a beta -octamolybdate subunit[Mo8O26](4-) covalently bonded to two [Cu(2,2'-bpy)(2)](2+) coordination complex cations via bridging oxo groups. In addition, the spectroscopic properties and thermal behavior of this compound have been investigated by spectroscopic techniques (UV-vis, IR, Raman and EPR spectra) and TG analysis.

Hydrothermal synthesis and crystal structure of [{Cu(2,2 '-bpy)(2)}(2)Mo8O26]: a beta-octamolybdate cluster covalently bonded to two {Cu(2,2 '-bpy)(2)}(2+) coordination complexes via bridging oxo groups

An organic-inorganic hybrid solid, (Cu(2,2'-bpy)(2))(2)Mo8O26, has been hydrothermally synthesized and structurally characterized by single-crystal X-ray diffraction. Dark green crystals crystallize in the orthorhombic system, space group Pna21, a = 24.164(5), b = 18.281(4), c = 11.877(2) Angstrom, alpha = 90 degrees, beta = 90 degrees, gamma = 90 degrees, V= 5247(2) Angstrom (3), Z = 4, lambda (MoK alpha) = 0.71073 Angstrom (R(F) = 0.0331 for 5353 reflections). Data were collected on a Siemens P4 four-circle diffractometer at 293 K in the range 1.69 degrees < theta < 25.04 degrees using the omega -scan technique. The structure was solved by the direct method and refined by full-matrix least squares on F-2 using SHELXL-93. The structure of this compound consists of discrete (Cu(2,2'-bpy)(2))(2)Mo8O26 clusters, constructed from beta -octamolybdate subunits ((Mo8O26)(4-)) covalently bonded to two (Cu(2,2'-bpy)(2))(2+) coordination complexes via bridging oxo groups that connect two adjacent molybdenum sites. (C) 2001 Academic Press.

峨眉山大火成岩省Ni-Cu-PGE矿床矿化类型变异机理研究

在峨眉山大火成岩省（ELIP）产出许多岩浆Cu-Ni-PGE岩浆硫化物矿床，如金宝山、杨柳坪、力马河、白马寨，以及大槽－阿布郎当矿化岩体。根据成矿元素组成特征，这些矿床可以区分为多种不同矿化类型，有以铂族元素为主贫铜镍的矿床，如金宝山Pt-Pd矿床；有含较高铂族元素和铜镍的矿床，如杨柳坪Ni-Cu-PGE矿床；也有贫铂族元素富铜镍的矿床，以力马河和白马寨Ni-Cu矿床最为典型。造成峨眉山大火成岩省中Ni-Cu-PGE岩浆硫化物矿床矿化类型变异的原因是什么？它们的母质岩浆性质如何，产生于怎样的熔融程度？既然能形成岩浆硫化物矿床，造成硫化物熔离的原因有哪些，什么因素起到了关键作用？这些矿化类型多样的Ni-Cu-PGE矿床的成矿岩浆有何差异？产生差异的原因是什么？带着这些疑问，通过借鉴国内外Ni-Cu-PGE岩浆硫化物矿床研究的经验，本文以金宝山铂钯矿、力马河镍矿及大槽－阿布郎当岩体的地球化学研究为基础，结合近几年来前人对杨柳坪，白马寨等矿床的系统研究，本文试图解决上述疑问。现在取得的主要认识有： 1） 根据成矿元素组成特征，可以把峨眉山大火成岩省中（ELIP）存在的Ni-Cu-PGE岩浆硫化物矿床分成多种不同的矿化类型，包括PGE矿床（例如金宝山Pt-Pd矿），Ni-Cu-PGE矿床（例如杨柳坪矿床），Ni-Cu矿床（例如力马河和白马寨矿床），以及弱矿化或不含矿的超镁铁质堆晶岩体（例如大槽－阿布郎当岩体）。通过对ELIP中几种类型Cu-Ni-PGE矿床成矿母岩浆的研究发现，它们均具有类似峨眉山苦橄岩的成分特征，表明母岩浆形成于较高程度的地幔部分熔融，并富集Ni和PGE。 2）硫化物熔离的多阶段性是导致矿床类型变异的一个重要因素。早期结晶矿物的分离结晶导致了金宝山母岩浆出现S的饱和，少量的浸染状硫化物被携带进入岩浆通道中发生了沉淀，继续富集PGE，形成了金宝山矿体。杨柳坪的母岩浆先发生了少量早期硫化物熔离丢失，PGE弱亏损的岩浆在后期上升过程中由于强烈的地壳混染，发生了大量硫化物熔离并发生堆积，形成杨柳坪矿体。力马河和白马寨的母岩浆在早期发生了较多的硫化物丢失，PGE强烈亏损的岩浆发生了二次以上的硫化物熔离，形成了力马河和白马寨矿体。 3） R因子（岩浆与熔离硫化物的比例）是决定ELIP中Cu-Ni-PGE矿床矿化类型变异的重要因素。金宝山矿床具有极高的R值（＞10000），杨柳坪和朱布矿床具有中等的R值（2000~5000），而力马河矿床近似为在经过R=2000的硫化物熔离之后，残余岩浆再经过R=200的硫化物熔离。 4） 地壳混染程度的差异可能是造成ELIP中Ni-Cu-PGE矿床矿化类型发生变异的关键因素。金宝山矿床的地壳混染程度较低，可能主要是早期橄榄石和铬铁矿的分异结晶导致了岩浆中硫化物出现了饱和。对于大槽－阿布郎当矿化岩体，只是在岩体边缘的局部出现了硫化物熔离，可能是围岩混染造成的。对于杨柳坪Ni-Cu-PGE矿床、力马河和白马寨Ni-Cu矿床，从微量元素蛛网中明显的Nb-Ta负异常，高放射成因187Os丰度的初始Os同位素组成（γOs(t)=100~120），S同位素等反映出显著的地壳混染，因而出现大量硫化物熔离。

中元古代昆阳群Fe-Cu-REE矿床地球化学研究-以武定迤纳厂矿床为例

稀土元素成矿与地壳的构造运动密切相关，稀土在中元古代具有大规模暴发性成矿特征。云南武定迤纳厂稀土铁铜矿床为昆阳群因民组出现稀土富集成矿的典型代表。本论文选择迤纳厂矿床为主要研究对象，系统研究矿床不同类型岩（矿）石和矿物的稀土元素地球化学特征，探讨富稀土的成矿流体、成矿物质来源和稀土元素成矿时代，揭示昆阳裂谷初期因民组稀土元素富集的地球化学机制。主要认识如下：1、迤纳厂矿床产于昆阳裂谷初期形成的禄丰一武定火山断陷盆地中。早中元古界昆阳群分布于绿汁江岩石圈断裂和小江一易门断裂的夹持地带，呈狭长状展布。迤纳厂矿床赋矿地层为昆阳群因民组上段的硅质白云岩和碱性火山岩（粗面安山岩）。矿体产出形态和矿石的结构构造等均显示矿体与赋矿地层同沉积特征；出现独立矿物氟碳饰矿、独居石及褐帘石，磷灰石、萤石、菱铁矿等矿物中也含有一定量的稀土，沿矿体走向和垂向稀土元素变化不大。2、矿体顶、底板围岩（石榴石黑云母片岩、钠长黑云母片岩等）的原岩为碱性火山岩（粗面安山岩），相对富集大离子亲石元素Ba、Cs、Rb、K、LRE日及贫Zr、Sr、Ti、Hf、HEE，为早元古代末期一中元古代早期交代富集地慢低程度部分熔融所形成的碱性火山岩。矿石稀土总量高（645-4443）×10-6，强烈富集轻稀土（（La/Tb）N＝17.3-81.1），稀土元素分布特征明显不同于矿区正常沉积的硅质白云岩和后期侵入的钠长石英斑岩及火山角砾岩，而与矿体顶、底板碱性火山岩中稀土元素配分特征基本一致，暗示稀土成矿物质来源与碱性火山岩有密切的关系；3、矿石中微量元素组合及变化特征与现代海底正在喷出的热液和热液沉积物中元素组合有较大的可比性，明显不同与火成碳酸岩型稀土矿床中的特征元素组合；在微量元素判别图解（Al-Fe-Mn、Fe／Ti-Al／（Al+Fe＋Mn）、U-Th、Y-P2O5等）中，逸纳厂矿石均投影在热水沉积区，矿石的Y／Ho值与黑烟囱值接近，表明成矿流体为高温、还原性质，稀土成矿可能以热水沉积作用方式为主；4、对矿石中主要矿物萤石、菱铁矿、磁铁矿、石英、方解石的稀土元素特征研究表明，矿石沉积时不同矿物中稀土元素分布特征基本相同，主要受成矿流体中稀土分布特征制约。而后期变质作用形成的矿物，其稀土元素分布主要受矿物晶体结构控制。同期成矿流体从早期到晚期（块状矿石→条带状矿石），轻重稀土分异变小，稀土总量增加，条带状矿石中稀土含量最高；矿石黄铜矿6345值变化在一任3％0到2g％。范围，显示慢源硫特征；菱铁矿6r3C（8％-9.1%）、δ18O（-11.17%-15.37）‰指示成矿流体具岩浆来源和有机质的脱梭酸分解作用参与；成矿流体中稀土元素可能主要以（RE（CO3）3F）4-、（既（CO3）3F2）、（RE（F，Cl万等形式迁移，当温度降低时沉淀出氟碳饰矿等稀土矿物；5、矿石和萤石单矿物 Sm-Nd等时线年龄分别为1621士110Ma和15：38士43Ma，与矿区碱性火山岩错石的U-Pb年龄1676Ma、因民组顶部石英正长斑岩的错石U-P1。年龄1685Ma基本一致，也与因民组地层年龄1765M。较为接近，反映成矿时代为早元古代晚期和中元古代早期：这一时间也与一早元古代晚期一中元古代早期昆阳裂谷初始裂陷阶段，大量来自于地幔的碱性火山岩喷发事件相吻合。矿石。Nd（t）:-2.87-3.60，萤石单矿物εNd（t）：-3.93-5.90，变化范围较窄并全为负值，接近0，指示源区为富集地幔。同时结合矿床形成的构造一地质环境及矿体产出的地质形态，认为逛纳厂稀土铁铜矿床可能是在昆阳裂谷初期，在碱性火山岩浆喷发的间歇期，来自地幔富稀土、挥发份的成矿流体由火山喷流一同生沉积方式形成的矿床。6、昆阳群因民组地层中出现的稀土富集、成矿与我国的白云鄂博稀土REE-Fe-Nb超大型矿一床和澳大利亚的olympic Dam Cu-U-Au-Ag-REE超大型矿床，在成矿时代、产出大地构造背景、成矿物质来源等方面具有较大的相似性，均体现成矿受控于中元古代1.5Ga超大陆聚合前或随后裂解初始阶段伴随的非造山型碱性岩浆或热液作用，稀土来源于超大陆拼合前因板块俯冲交代而形成的富集地幔。

Characterization of carbonated tricalcium silicate and its sorption capacity for heavy metals: A micron-scale composite adsorbent of active silicate gel and calcite

Adsorption-based processes are widely used in the treatment of dilute metal-bearing wastewaters. The development of versatile, low-cost adsorbents is the subject of continuing interest. This paper examines the preparation, characterization and performance of a micro-scale composite adsorbent composed of silica gel (15.9 w/w%), calcium silicate hydrate gel (8.2 w/w%) and calcite (75.9 w/w%), produced by the accelerated carbonation of tricalcium silicate (C(3)S, Ca(3)SiO(5)). The Ca/Si ratio of calcium silicate hydrate gel (C-S-H) was determined at 0.12 (DTA/TG), 0.17 ((29)Si solid-state MAS/NMR) and 0.18 (SEM/EDS). The metals-retention capacity for selected Cu(II), Pb(II), Zn(II) and Cr(III) was determined by batch and column sorption experiments utilizing nitrate solutions. The effects of metal ion concentration, pH and contact time on binding ability was investigated by kinetic and equilibrium adsorption isotherm studies. The adsorption capacity for Pb(II), Cr(III), Zn(II) and Cu(II) was found to be 94.4 mg/g, 83.0 mg/g, 52.1 mg/g and 31.4 mg/g, respectively. It is concluded that the composite adsorbent has considerable potential for the treatment of industrial wastewater containing heavy metals.