Análise de marcas de crescimento ósseo e estimativas de idade para Chelonia mydas (Linnaeus, 1758) no litoral do Rio Grande do Sul

A tartaruga-verde, Chelonia mydas, possui ampla distribuição geográfica circuntropical, ocorrendo em toda zona costeira brasileira. A espécie está incluída em diversas listas de animais ameaçados de extinção, sendo assim fundamental a elaboração de modelos demográficos que possam vir a subsidiar futuros planos de manejo. Contudo, muitos aspectos referentes à história de vida destes animais ainda são pouco conhecidos, por serem animais marinhos de difícil observação, especialmente durante o período que despendem nas áreas de alimentação e durante as grandes migrações. As tartarugas marinhas apresentam características, em seu ciclo de vida, que dificultam a realização de estudos de marcação e recaptura, para determinação de parâmetros importantes como crescimento e determinação de idade. Por esta razão, muitos estudos envolvendo determinação de idade utilizando linhas cíclicas de crescimento presentes nos tecidos rígidos - esqueletocronologia, vêm sendo acumulados para esta espécie. Muito pouco se sabe sobre quaisquer aspectos relacionados às etapas do ciclo de vida das tartarugas marinhas que habitam o litoral do Rio Grande do Sul, deste modo, este estudo tem como principal objetivo avaliar a técnica histológica utilizada usualmente nas análises de esqueletocronologia em tartarugas marinhas a fim de verificar a ocorrência de crescimento cíclico nos ossos e de se obter estimativas de idade para a população local. As amostras são provenientes de tartarugas-verdes encalhadas no litoral norte do Rio Grande do Sul e coletadas, de forma sistemática entre Torres e Mostardas, de março de 1994 a setembro de 2003. Os 89 exemplares (35%) de tartarugas-verdes registrados indicam que a espécie é a segunda em número de ocorrências, sendo menos freqüente apenas que Caretta caretta (54%). Foi verificada apenas a ocorrência de exemplares juvenis (ccc = 29,0 a 52,0 cm, média = 38,9cm), que estão iniciando o período de desenvolvimento costeiro. A técnica avaliada não apresentou os resultados esperados, necessitando de algumas modificações metodológicas. A partir da observação dos cortes histológicos pôde-se constatar a presença de linhas de crescimento ósseo em apenas onze dos vinte e quatro indivíduos que apresentaram resultados satisfatórios na preparação histológica, indicando que a deposição das linhas pode ser variável e dependente de fatores ambientais. Nos onze indivíduos puderam ser distinguidas de uma a cinco linhas de crescimento, indicando uma idade entre 1 e 5 anos para o término da fase no ambiente pelágico. Com estes resultados obteve-se o primeiro registro da presença de linhas de crescimento ósseo, assim como, a primeira estimativa de idade para a população de Chelonia mydas no início de sua fase de desenvolvimento costeiro no Brasil.

Beneficiamentos da cinza de casca de arroz residual com vistas à produção de cimento composto e/ou pozolânico

A cinza de casca de arroz é um resíduo agro-industrial decorrente do processo de queima da casca de arroz, sendo largamente encontrada no Rio Grande do Sul, pois, historicamente, este Estado é o maior produtor de arroz no Brasil, com cerca de 45% da produção nacional. Empregada como fonte de energia, a casca de arroz é queimada em diversas empresas; algumas, devido à sua natureza, incorporam a cinza ao produto, mas a maioria não encontra outro destino que não o descarte em forma de aterro, criando, assim, um problema ambiental de poluição do solo, do ar e de rios e córregos. No entanto, devido à presença de elevado percentual de sílica (SiO2) na sua constituição, a cinza de casca de arroz pode ter vários empregos. Na construção civil, pode ser empregada como pozolana, conforme vários estudos já vêm demonstrando. Porém, encontra restrições por motivos como sua cor escura, que confere aos cimentos, argamassas e concretos aos quais é adicionada, uma coloração também escura, e a falta de uniformidade apresentada em termos de características químicas e, principalmente, mineralógicas. A cor escura não é um problema de ordem técnica, mas estética e de aceitação no mercado. Já a composição mineralógica está associada à atividade pozolânica e a falta de uniformidade do material disponível implica na incerteza do grau de reatividade. Este trabalho teve o objetivo de verificar a viabilidade técnica do emprego de cinzas de casca de arroz residuais na confecção de cimentos Portland composto e/ou pozolânico, a partir de beneficiamentos das mesmas, que associam tratamentos físicos, químicos e/ou térmicos, os quais têm como finalidade reverter e/ou minimizar os aspectos negativos citados. Para tanto, foram empregadas três cinzas de casca de arroz, oriundas de diferentes processos de produção e com composições mineralógicas distintas. Após definidos os tratamentos a serem aplicados, através de seleção pelos critérios de cor e composição mineralógica, as cinzas tratadas foram avaliadas quanto à sua pozolanicidade, pelo Índice de Atividade Pozolânica (IAP) da NBR 5752 e também por um IAP alterado, proposto neste trabalho. A produção de cimentos com CCA beneficiada se deu a partir de um cimento base com substituição por CCA, em massa e em diferentes percentuais. Tais cimentos foram avaliados quanto à resistência à compressão, aos tempos de pega, à pozolanicidade e à expansibilidade a quente. A análise dos dados obtidos indica que os tratamentos propostos e/ou a associação deles resultam em beneficio no desempenho das cinzas, em pelo menos um dos vários aspectos considerados. A presente pesquisa permite concluir que as CCA residuais têm potencial para serem empregadas na produção de cimentos, tanto aquelas menos cristalinas, quanto as mais cristalinas. Para tanto, devem ser beneficiadas, sendo pelo menos submetidas a tratamento físico para redução de sua granulometria. Se outros objetivos forem pretendidos, como coloração clara, os tratamentos térmico ou químico podem ser empregados.

Construção com painéis sanduíche de silicato de cálcio, cimento e EPS

A carência de materiais que permitam elementos estruturais leves, de elevada rigidez e resistência na indústria da construção, contribuiu para o desenvolvimento e posterior utilização de materiais compósitos, nos quais incluem-se os painéis sanduíche. Estes são aperfeiçoados e fabricados com o objetivo de obter elevada relação resistência/peso próprio, rigidez/peso próprio e outras vantagens a nível construtivo como a montagem rápida, a redução de custos e boas propriedades de isolamento. Nesta dissertação são apresentados os painéis sanduíche de silicato de cálcio, cimento e EPS, com o intuito de informar os interessados, em métodos construtivos alternativos, sobre uma solução viável, vantajosa a vários níveis e que pode ser adaptada e igualmente adequada às suas necessidades construtivas. Inicia-se com um resumo do desenvolvimento histórico até à necessidade de evolução e utilização de materiais semelhantes, seguindo-se de uma descrição mais detalhada do painel sanduíche e os seus requisitos. A nível de fabrico, sugere-se uma possível disposição de maquinaria em fábrica e pormenoriza-se o processo de fabrico até atingir o produto final. Segue-se o trajeto do painel até ao seu propósito final em obra, onde se descreve o seu processo construtivo. Explicam-se as vantagens e desvantagens dos Painéis acompanhados de vários exemplos de aplicações com sucesso. Para divulgar a qualidade e facilitar a comercialização deste produto, descreve-se detalhadamente o processo moroso da obtenção da marca que atesta a conformidade de um produto a nível europeu e mundial, a marcação CE, e a nível nacional, uma proposta de especificação técnica como comprovativo de qualidade. É ainda realizado um estudo teórico do desempenho esperado dos painéis sanduíche de silicato de cálcio, cimento e EPS, a nível acústico, térmico, a sua resistência à água e fogo, durabilidade a longo prazo e resistência dos Painéis. Por fim, demonstram-se vários pormenores construtivos que eventualmente serão utilizados em obra.

Adição de superplastificante e anti-segregante à base de CMC em pastas de cimento para Poços de Petróleo

Oil well cementing materials consist of slurries of Special class Portland cement dispersed in water. Admixtures can be used to provide the necessary fluidity, so the material can be efficiently pumped down as well as penetrate porous rocks with controlled filter loss. Construction admixtures can be used to modify the properties of oil well cements provided they can withstand and hold their properties at the higher than ambient temperatures usually encountered in oil fields. In civil construction, superplasticizer play the role of dispersants that reduce the facto r of water cement improve mechanical properties and fluidity of the cement, whereas anti-segregation agents improve the workability of the slurry. In the present study, oil well cement slurries were produced adding both a dispersant and an anti-segregation agent conventionally used in Portland CPII-Z-32 RS cement aiming at materials for primary cementing and squeeze operations. Three basic aspects were evaluated: fluidity, filter loss and the synergetic effect of the admixtures at two temperatures, i.e., 27°C and 56°C, following API RP 10B practical recommendations. The slurries were prepared using admixture concentrations varying from 2.60 Kgf/m3 (0.02 gallft3) to 5.82 Kgf/m3 (0.045 galJft3) BWOC. The density of the slurries was set to 1.89 g/cm3 (15.8 Ib/gal). 0.30 to 0.60% BWOC of a CMC-based anti-segregation agent was added to the cement to control the filter loss. The results showed that the addition of anti-segregation at concentrations above 0.55% by weight of cement resulted in the increased viscosity of the folders in temperatures evaluated. The increasing the temperature of the tests led to a reduction in the performance of anti-segregation. At concentrations of 5.20 kgf/m3 (0,040 gallft3) and 5.82 Kgf/m3 (0,045 gal/ft 3) observed a better performance of the properties evaluated in the proposed system. At low temperature was observed instability in the readings of rheology for all concentrations of anti-segregation. Contents that increasing the concentration of anti¬-segregation is limited concentrations greater than 0.55 % BWOC of the CMC in temperature analyzed. The use of the system with CMC promoted a good performance against the properties evaluated. The principal function of anti¬-segregation was optimized with increasing concentration of superplasticizer, at temperatures above the 2rC. The study of the behaviour of systemic additives, resulting in slurries of cement, which can be optimized face studies of other intrinsic properties in oil fields

Análise do comportamento reológico de pastas de cimento contendo resíduos de pneu para poços de petróleo

The low tenacity presented by the Portland cement pastes used in the oil wells cementation has been motivating several researches with attention focused on alternative materials. Additives have been developed to generate flexible pastes with mechanical resistance capable to support the expansions and retractions of the metallic covering of the wells that submit to the steam injection, technique very used to increase the recovery factor in oil reservoirs with high viscosity. A fresh paste with inadequate rheological behavior may commit the cementation process seriously, involving flaws that affect the performance of the paste substantially in the hardened state. This work proposes the elaboration and the rheological analysis of Portland cement pastes with addition of residues of rubber tire in several proportions, with the aim of minimizing the damages provoked in the hem cementing of these wells. By thermogravimetric analysis, the particles of eraser that go by the sieve of 0,5mm (35 mesh) opening and treated superficially with NaOH solution of 1 mol/L presented appropriate thermal resistance for wells that submit to thermal cyclic. The evaluation of the study based on the results of the rheological analysis of the pastes, complemented by the mechanical analysis, thickening, stability, tenor of free water and filtrate loss, being used as parameter a paste reference, without rubber addition. The results showed satisfactory rheology, passive of few corrections; considerable loss of mechanical resistance (traction and compression), compensated by earnings of tenacity, however with established limits for its application in oil wells; satisfactory stability, free water and thickening time

Avaliação da influência do nacl em pastas de cimento portland para cimentação de poços de petróleo em zonas evaporíticas

One of the major current challenges for oilwell companies is the extraction of oil from evaporitic zones, also known as pre-salt basins. Deep reservoirs are found under thick salt layers formed from the evaporation of sea water. Salt layers seal the flow of oil from underneath rock formations, which store hydrocarbons and increase the probability of success in oil and gas exploration. Oilwells are cemented using Portland-based slurries to promote mechanical stability and zonal isolation. For pre-salt oilwells, NaCl must be added to saturate the cement slurries, however, the presence of salt in the composition of slurries affects their overall behavior. Therefore, the objective of the present study was to evaluate the effect of the addition of 5 to 25% NaCl on selected properties of Portland-based slurries. A series of tests were carried out to assess the rheological behavior, thickening time, free water and ultrassonic compressive strength. In addition, the slurries were also characterized by thermal analysis, X ray diffraction and scanning electron microscopy. The results showed that the addition of NaCl affected the thickening time of the slurries. NaCl contents up to 10% shortened the thickening time of the slurries. On the other hand, concentrations in excess of 20% not only extended the thickening time, but also reduced the strength of hardened slurries. The addition of NaCl resulted in the formation of a different crystalline phase called Friedel´s salt, where free chlorine is bonded to tricalcium aluminate

Estudo da incorporação de cascalho proveniente da perfuração de poços de petróleo em formulações para tijolos de solo-cimento

The present work is to study the characteristics and technological properties of soil-cement bricks made from binary and ternary mixtures of Portland cement, sand, water, with or without addition of gravel from the drilling of oil wells, which could be used by industry, aiming to improve its performance and reduce cost by using the residue and, consequently, increasing its useful life. The soil-cement bricks are one of the alternatives to masonry construction. These elements, after a short curing period, provide compressive strength similar to that of solid bricks and ceramic blocks, and the higher the resistance the higher the amount of cement used. We used the soil from the city of São José do Mipibu / RN, the banks of the River Baldun, cement CPIIZ-32 and residue of drill cuttings from oil wells drilling onshore wells in the town of Mossley, RN, provided Petrobras. To determine the optimum mix, we studied the inclusion of different residues (100%, 80%, 70%, 60% and 50%) where 15 bodies were made of the test piece. The assessment was made of bricks made from simple compression tests, mass loss by immersion and water absorption. The experimental results proved the efficiency and high utilization of the waste from the drilling of oil wells, making the brick-cement-soil residue with a higher strength and lower water absorption. The best result in terms of mechanical strength and water absorption for the ternary mixture was 10% soil, 14% cement and 80% residue. In terms of binary mixtures, we obtained the best result for the mix-cement residue, which was 14% cement incorporated in the residue

Desenvolvimento de pastas de cimento flexíveis para poços de petróleo submetidos à injeção de vapor utilizando látex do tipo SBR

Novel cementing materials formulations containing flexible polymeric admixtures have been studied aiming at improving the mechanical behavior of oil well cement slurries submitted to steam injection. However, research activities in this sector are still under development. The steam injected directly into the well causes casing dilation, which after a reduction in temperature, tends to return to its original dimensions, resulting in crack formation and hydraulic isolation loss of the well, which will result in shortening of well life. In this scenario, the objective of the present study was to evaluate the mechanical behavior of Portland-based slurries containing SBR latex, applied in oil well cementing of wells submitted to steam injection. Were formulated slurries with densities of 1.797 g/cm3 (15.0 lb/Gal) and 1.869 g/cm3 (15.6 lb/Gal), containing admixtures with a latex concentration of 0; 66.88; 133.76; 200.64 and 267.52 L/m3 (0, 0.5, 1.0, 1.5 and 2.0 gpc). Tests including rheology, fluid loss control, thickening time, API compressive strength and splitting tensile strength, beyond steam injection simulation. Microstrutural characteristics of the slurries were also performed (XRD, TG, FTIR and SEM). The results showed that increasing the polymer concentration increased in the rheological properties and fluid loss, and a decrease in the elasticity modulus of the cement slurries. The results obtained showed that the slurries can be applied in cementing operations of oil wells submitted to steam injection.

Estudo da incorporação da cal em composições binárias de solo-cimento para produção de tijolos maciços

The use of binders in the soil for the production of solid bricks is an old construction technique that has been used by several civilizations over time. At the same time, the need for environmental preservation and the tendency of scarcity of natural resources make the construction invest in researching new concepts, methods and materials for building systems for the sustainability of their economic activities. Thus arises the need to obtain building materials with low power consumption, capable of reducing the growing housing shortage of rural and urban population. Currently, research has been conducted on this topic to better understand the cementitious and pozzolanic reactions that occur in the formation of the microstructure of the soil-cement when added to other materials such as, for example, lime, and the relationship between microstructure and formed interfaces with the physical, mechanical and chemical analysis in compounds made from these ternary compositions. In this context, this study aimed to analyze the results of the influence of the incorporation of lime to the soil-cement to form a ternary mixture to produce soil-cement bricks and mortar without structural purposes. From the inclusion of contents of 6 %, 8 %, 10% and 12% lime to the soil, and soil-cement mixes in amounts of 2 %, 3 %, 4 % and 5 % were shaped-bodies of -cylindrical specimens to determine the optimum moisture content and maximum dry apparent specific weight. Then they were cured, and subjected to the tests of compressive strength, absorption and durability modified. Compositions obtained the best results in the tests performed on the bodies-of-proof cylindrical served as a parameter for molding of solid bricks, which underwent the same experimental methodology previously cited. The raw materials used, as well as compositions in which the bricks were molded solid, were characterized by physical and chemical tests, X-ray diffraction and scanning electron microscopy. The results obtained in the study indicate that the compositions studied, that showed the best results in terms of compressive strength, water absorption and durability ternary composition was soil, 10 % cement and 2 % lime

influência da adição de diferentes sais em pastas de cimento portland para cimentação de poços de petróleo

One of the great challenges at present time related with the materials area concerns of products and processes for use in petroleum industry, more precisely related to the Pre-salt area. Progresses were reached in the last years allowing the drilling of the salt layer, with the time reduction for drilling and larger success at the end. For the oil wells companies the preponderant factor is the technology, however, in spite of the progress, a series of challenges is still susceptible to solutions and one of them refers to the slurries preparation for cementing in those areas. Inside of this context, this study had for objective to analyze the influence of the salts NaCl, KCl, CaSO4 and MgSO4 in strength and chemical structure of the hydrated products. As methodology, they were prepared and analyzed cement slurries with varied concentrations of these salts that are commonly found in the saline formations. The salts concentrations used in formulations of the slurries were of 5%, 15% and 30%. The slurries were formulated with specific weight of 15,8 lb / gal and the cement used was Class G. Strength tests were accomplished in samples cured by 24 hours and 28 days. Also were realized crystallographic characterization (XRD) and morphologic (SEM). In agreement with the presented results, it is observed that the largest resistance values are attributed to the slurries with concentration of 15%. There was reduction of the strength values of the slurries formulated with concentration of 30%. Through the characterization microstructural it was possible to note the salts influence in the main cement hydrated products

Avaliação da adição de Nanosílica e silicato de sódio em pastas de cimento para poços de petróleo com baixo gradiente de fratura

The oil wells cementing is a critical step during the phase of well drilling, because problems during the operation of slurry pumping and an incomplete filling of the annular space between the metal casing and the formation can cause the slurry loss. Therefore, the slurry adopted in primary cementing an oil well must be properly dosed so that these problems are avoided during its pumping. When you drill a well in a weak rock formation requires even more careful, because should be a limit of hydrostatic pressure exerted during cementation, that does not occur rock collapse. With the objective of performing the cementing of a well whose formation is weak or unconsolidated are employed lighter slurries. Thus, this study used slurries with sodium silicate and nano silica in concentrations of 0,1; 0,4; 0,7 e 1,0 gpc, in which the slurries with nano silica showed the rheological parameters higher concentrations of up to 0.7 gpc and for concentration of 1.0 the slurry with sodium silicate obtained the highest values, remaining above the limits for application in fields, mainly wells with low fracture gradient, because a significant increase in viscosity may result in an increase in pressure pumping in operations of secondary cementations. Furthermore, there was no decrease in strength with increasing concentration of additive. Then, it is possible use of these additives to formulate Lighter slurry

Desenvolvimento de um sistema misto de pasta à base de geopolímero e cimento portland para correção de perda de circulação

The materials engineering includes processes and products involving several areas of engineering, allowing them to prepare materials that fulfill the needs of various new products. In this case, this work aims to study a system composed of cement paste and geopolymers, which can contribute to solving an engineering problem that directly involves the exploitation of oil wells subject to loss of circulation. To correct it, has been already proposed the use of granular materials, fibers, reducing the drilling fluid or cement paste density and even surface and downhole mixed systems. In this work, we proposed the development of a slurry mixed system, the first was a cement-based slurry and the second a geopolymer-based slurry. The cement-based slurry was formulated with low density and extenders, 12.0 ppg (1.438 g/cm ³), showing great thixotropic characteristics. It was added nano silica at concentrations of 0.5, 1.0 and 1.5 gps (66.88, 133.76 and 200.64 L/m3) and CaCl2 at concentrations of 0.5, 1, 0 and 1.5%. The second system is a geopolymer-based paste formulated from molar ratios of 3.5 (nSiO2/nAl2O3), 0.27 (nK2O/nSiO2), 1.07 (nK2O/nAl2O3) and 13.99 (nH2O/nK2O). Finally, we performed a mixture of these two systems, for their application for correction of circulation lost. To characterize the raw materials, XRD, XRF, FTIR analysis and titration were performed. The both systems were characterized in tests based on API RP10B. Compressive strength tests were conducted after curing for 24 hours, 7 and 28 days at 58 °C on the cement-based system and the geopolymer-based system. From the mixtures have been performed mixability tests and micro structural characterizations (XRD, SEM and TG). The results showed that the nano silica, when combined with CaCl2 modified the rheological properties of the cement slurry and from the concentration of 1.5 gpc (200.64 L / m³) it was possible to obtain stable systems. The system mixture caused a change in the microstructure of the material by favoring the rate of geopolymer formation to hinder the C3S phase hydration, thus, the production of CSH phases and Portlandite were harmed. Through the mixability tests it can be concluded that the system, due to reduced setting time of the mixture, can be applied to plug lost circulation zones when mixed downhole