A renewable copper electrode as an amperometric flow detector for nitrate determination in mineral water and soft drink samples

A novel approach was developed for nitrate analysis in a FIA configuration with amperometric detection (E=-0.48 V). Sensitive and reproducible current measurements were achieved by using a copper electrode activated with a controlled potential protocol. The response of the FIA amperometric method was linear over the range from 0.1 to 2.5 mmol L(-1) nitrate with a detection limit of 4.2 mu mol L(-1) (S/N = 3). The repeatability of measurements was determined as 4.7% (n=9) at the best conditions (flow rate: 3.0 mL min(-1), sample volume: 150 mu L and nitrate concentration: 0.5 mmol L(-1)) with a sampling rate of 60 samples h(-1). The method was employed for the determination of nitrate in mineral water and soft drink samples and the results were in agreement with those obtained by using a recommended procedure. Studies towards a selective monitoring of nitrite were also performed in samples containing nitrate by carrying out measurements at a less negative potential (-0.20 V). (C) 2009 Elsevier B.V. All rights reserved.

When a local competitor (slightly) shakes up the global giant: a case on the soft drink market

As marcas globais mantiveram muita atenção no campo do marketing (Kotler, 1997; Holt, Quelch, e Taylor, 2004; Özsomer e Altaras, 2008), enquanto as marcas locais foram subestimadas (Ger, 1999; Schuiling e Kapferer, 2004). No entanto, o debate adaptação contra padronização foi amplamente discutido. Centra-se na definição de como uma empresa internacional deve construir a sua estratégia: ao padronizar sua estratégia de marketing ou, adaptando para melhor atender a cultura e às necessidades locais (Levitt, 1983; Subhash, 1989; Herbig, 1998; Holt, 2004; Melewar e Vemmervik , 2004; Heerden e Barter, 2008). No entanto, este assunto não foi discutido no contexto específico do consumo alternativo oferecido por concorrentes locais específicos. Hoje em dia, um aumento na oferta de produtos alternativos é observado. O consumo socialmente responsável está crescendo (Sen e Bhattacharya, 2001; Holt, 2002; Loureiro, 2002; François-Lecompte e Valette-Florence, 2006). O mercado dos refrigerantes de cola é de interesse particular. Colas alternativas são refrigerantes de cola que surgiram durante a última década em algumas regiões ou zonas específicas do mundo. Estas colas claramente posicionam-se como uma alternativa ao refrigerante global Coca-Cola. A alternativa não é baseada no preço mas nas características especiais dos produtos que constituem uma proposição de valor específica, diferente da Coca-Cola. Na França, desde uma década, o número de colas regionais aumentou, sendo mais de quinze hoje. O refregirante Breizh Cola foi lançado em 2002 e atinge quase uma quota de mercado de 10% na região Bretanha hoje. Em 2009, a Coca-Cola Entreprise iniciou uma campanha de marketing específica, na Bretanha, baseada em recursos visuais e parcerias regionais. Este caso de adaptação em um contexto de concorrência local específico é explorado nesta dissertação que incide sobre as razões da preferência para Breizh Cola, de um lado, e sobre as acções empreendidas pela Coca-Cola na Bretanha, do outro lado. Este estudo mostra que a Coca-Cola anda nos passos de Breizh Cola, a fim de melhor atender às expectativas local.

Antioxidant Activity of Commercial Ready-to-Drink Orange Juice and Nectar

Total antioxidant activity (TAA), total phenolic compounds (TPC), and physicochemical characteristics of ready-to-drink orange juice and nectar from the most consumed brands available in Brazil were evaluated. TPC ranged from 18.7 to 54.2 mg of gallic acid/100 mL, and TAA varied from 57.88 to 349.32 mu mol TEAC/100 mL ready-to-drink orange juice and nectar. The ascorbic acid content was the only physicochemical parameter that showed strong variation among packages and brands. Correlation of TPC with TAA showed that the higher the level of TPC the higher the TAA. Correlation of ascorbic acid content with TAA is higher for ready-to-drink orange juice than nectar. The same was found for the correlation of ascorbic acid content with TPC. The results confirm the contribution of the TPC to TAA.

Effect of 4% titanium tetrafluoride solution on dental erosion by a soft drink: An in situ/ex vivo study

Objective: This in situ/ex vivo study assessed the effect of titanium tetrafluoride (TiF4) on permanent human enamel subjected to erosion.Design: Ten volunteers took part in this study performed in two phases. In the first phase (ERO), they wore acrylic palatal appliances containing two enamel blocks, divided into two rows: TiF4 (F) and no-TiF4 (no-F). During the 1st day, the formation of a salivary pellicle was allowed. In the 2nd day, the TiF4 solution was applied on one row (ERO + F), whereas on the other row no treatment was performed (ERO + no-F). From 3rd until 7th day, the blocks were subjected to erosion, 4x per day. In the 2nd phase (no-ERO), the volunteers wore acrylic palatal appliances containing one enamel block, during 2 days, to assess the effect of TiF4 only (no-ERO + F). Enamel alterations were determined using profilometry (wear), microhardness (%SMHC) tests, scanning electron microscope and microprobe analysis. The %SMHC and wear were tested using ANOVA and Tukey's post hoc tests (p < 0.05).Results: The mean of %SMHC and wear ( mu m) values ( +/- S.D.) were, respectively: ERO + F -73.32 +/- 5.16(A)/2.40 +/- 0.60(a); ERO + no-F -83.49 +/- 4.59B/1.17 +/- 0.48(b) and no-ERO + F -67.92 +/- 6.16(A)/0.21:E 0.09(c). In microscope analysis, the no-F group showed enamel with honeycomb appearance. For F groups, it was observed a surface coating with microcracks. The microprobe analysis revealed the presence of the following elements (%) in groups ERO + F, ERO + no-F and no-ERO + F, respectively: Ca (69.9, 72.5, 66.25); P (25.9, 26.5, 26.06); Ti (3.0, 0, 5.93).Conclusions: The TiF4 was unable to reduce dental erosion. (c) 2007 Elsevier Ltd. All rights reserved.

Effect of an experimental 4% titanium tetrafluoride varnish on dental erosion by a soft drink

Objectives: This in vitro study assessed the effect of an experimental 4%TiF4 varnish on enamel erosion.Methods: Sixty bovine enamel blocks were randomly allocated to each type of varnish:Duraphat((R)) -D (NaF, 2.26%F), Duofluorid((R))-F(NaF, 2.71% F), TiF4-T(2.45%F) and no-fluoride-P. After application of the varnishes, the blocks were subjected to six sequential pH cycles (cola drink for 10 min and artificial saliva for 50 min, each) per day, during 4 days. After the pH cycles, the blocks were maintained in artificial saliva for 18 h. Enamel alterations were determined in the 2nd and 4th days, using profilometry (wear) and microhardness (%SMHC) tests. Data were tested using ANOVA and Tukey's tests (p < 0.05).Results: the mean %SMHC (+/- S.D.) at the 2nd and 4th day was, respectively, D (-77.26 +/- 5.04(a) and -88.59 +/- 5.11(A)), F (-76.79 +/- 7.82(a) and -88.78 +/- 6.10(A)), T(-88.28 +/- 3.19(b) and -92.04 +/- 2.54(A,B)) and P (-87.96 +/- 2.23(b) and -94.15 +/- 1.14(B)). The mean wear (mu m +/- S.D.) at the 2nd and 4th day was, respectively, D (3.16 +/- 0.32(a) and 7.56 +/- 0.90(A)), F(3.35 +/- 0.78(a,b) and 7.92 +/- 0.98(A)), T (3.81 +/- 0.43(b) and 7.69 +/- 0.76(A)) and P (3.43 +/- 1.13(a,b) and 7.31 +/- 0.53(A)).Conclusions: the NaF varnishes reduced the softening, but had no effect on the reduction of the wear. The TiF4 varnish was not able to reduce the softening and wear. (C) 2007 Elsevier Ltd. All rights reserved.

Relax and fix heuristics to solve one-stage one-machine lot-scheduling models for small-scale soft drink plants

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Solution approaches for the soft drink integrated production lot sizing and scheduling problem

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Survey of the Microbiological Quality of Nonalcoholic Carbonated Beverages

The number and the main groups of microorganisms present in samples of different nonalcoholic carbonated beverages (lemon, orange and guaraná soft drinks) obtained from a small factory were analyzed. The samples were obtained at the end of the processing line. They were then divided into two lots: one was sent to immediate analysis, the other was stored at environmental temperature for 90 d thereafter it was submitted to the same analysis. Aliquots of 1 mL were drawn from the various samples and the corresponding decimal dilutions were prepared. They were then grown in culture media and counts of mesophilic aerobic bacteria, molds and yeasts, acid-producing bacteria, total and fecal coliforms were taken. It was observed that, of all the analyzed samples, at time 0 or after storage sample C (orange) was the best, since it conformed to the microbiological standards established by legislation. The guaraná type could also be consumed on day zero; the lemon type was inadequate for consumption of all the analyzed samples, the orange type was the only one that could be consumed within 3 months of storage.

The influence of residual salivary fluoride from dentifrice on enamel erosion: An in situ study

The objective of this study was to assess the salivary residual effect of fluoride dentifrice on human enamel subjected to an erosive challenge. This crossover in situ study was performed in two phases (A and B), involving ten volunteers. In each phase, they wore acrylic palatal appliances, each containing 3 human enamel blocks, during 7 days. The blocks were subjected to erosion by immersion of the appliances in a cola drink for 5 minutes, 4 times a day. Dentifrice was used to brush the volunteers' teeth, 4 times a day, during 1 minute, before the appliance was replaced into the mouth. In phases A and B the dentifrices used had the same formulation, except for the absence (PD) or presence (FD) of fluoride, respectively. Enamel alterations were determined using profilometry, microhardness (%SMHC), acid- and alkali-soluble F analysis. The data were tested using ANOVA (p < 0.05). The concentrations (mean ± SD) of alkali- and acid-soluble F (μgF/cm 2) were, respectively, PD: 1.27 a ± 0.70/2.24∧ A ± 0.36 and FD: 1.49 a ± 0.44/2.24∧ ± 0.67 (p > 0.05). The mean wear values (± SD, μm) were PD: 3.63 a ± 1.54 and FD: 3.54 a ± 0.90 (p > 0.05). The mean %SMHC values (± SD) were PD: 89.63 a ± 4.73 and FD: 87.28 a ± 4.01 (p > 0.05). Thus, we concluded that the residual fluoride from the fluoride-containing dentifrice did not protect enamel against erosion.

Scanning electron microscopic study of the in situ effect of salivary stimulation on erosion and abrasion in human and bovine enamel

This in situ study investigated, using scanning electron microscopy, the effect of stimulated saliva on the enamel surface of bovine and human substrates submitted to erosion followed by brushing abrasion immediately or after one hour. During 2 experimental 7-day crossover phases, 9 previously selected volunteers wore intraoral palatal devices, with 12 enamel specimens (6 human and 6 bovine). In the first phase, the volunteers immersed the device for 5 minutes in 150 ml of a cola drink, 4 times a day (8h00, 12h00, 16h00 and 20h00). Immediately after the immersions, no treatment was performed in 4 specimens (ERO), 4 other specimens were immediately brushed (0 min) using a fluoride dentifrice and the device was replaced into the mouth. After 60 min, the other 4 specimens were brushed. In the second phase, the procedures were repeated but, after the immersions, the volunteers stimulated the salivary flow rate by chewing a sugar-free gum for 30 min. Enamel superficial alterations of all specimens were then evaluated using a scanning electron microscope. Enamel prism core dissolution was seen on the surfaces submitted to erosion, while on those submitted to erosion and to abrasion (both at 0 and 60 min) a more homogeneous enamel surface was observed, probably due to the removal of the altered superficial prism layer. For all the other variables - enamel substrate and salivary stimulation the microscopic pattern of the enamel specimens was similar.

Meta-heuristic approaches for a soft drink industry problem

The present paper evaluates meta-heuristic approaches to solve a soft drink industry problem. This problem is motivated by a real situation found in soft drink companies, where the lot sizing and scheduling of raw materials in tanks and products in lines must be simultaneously determined. Tabu search, threshold accepting and genetic algorithms are used as procedures to solve the problem at hand. The methods are evaluated with a set of instance already available for this problem. This paper also proposes a new set of complex instances. The computational results comparing these approaches are reported. © 2008 IEEE.

Effect of an acid diet allied to sonic toothbrushing on root dentin permeability: An in vitro study

This study quantified alterations in root dentin permeability after exposure to different acid beverages. Twenty-five third molars were sectioned below the cementoenamel junction, the root segment was collected, and the pulp tissue was removed. The root segments were connected to a hydraulic pressure apparatus to measure the permeability of root dentin after the following sequential steps, with 5 specimens in each: 1) phosphoric acid etching for 30 s (maximum permeability), 2) root planning to create new smear layer, 3) exposure to different acid substances for 5 min (orange, cola drink, vinegar, white wine, lemon juice), 4) toothbrushing with sonic toothbrush for 3 min, 5) toothbrushing with sonic toothbrush plus dentifrice for 3 min. Considering step I as 100%, the data were converted into percentage and each specimen was its own control. Data were analyzed statistically by Kruskal-Wallis and Dunn's post test at 5% significance level. All acidic substances increased dentin permeability significantly after scraping (p<0.05). Toothbrushing after exposure to acid substances decreased dentin permeability and the association with dentifrice accentuated the decrease (p<0.05), except for the specimens treated with cola drink. Thus, it may be concluded that all tested acid fruit juices increased dentin permeability, and toothbrushing with or without dentifrice can decrease root dentin permeability after dentin exposure to acid diet.

Strategies to model scheduling decisions to plan the soft drink production process

In this paper we present a mixed integer model that integrates lot sizing and lot scheduling decisions for the production planning of a soft drink company. The main contribution of the paper is to present a model that differ from others in the literature for the constraints related to the scheduling decisions. The proposed strategy is compared to other strategies presented in the literature.

Consumer interpretation of ready to drink orange juice and nectar labelling

The aim of this study was to evaluate consumers' use and interpretation of ready to drink orange juice and nectar label information and its influence on the purchase decision. One hundred and sixty-seven consumers of ready to drink orange juice and nectar were interviewed. The labels were analysed to evaluate their conformance to Brazilian legislation. The manufacturing and shelf life date were the information most often checked, followed by health related issues. Brand, price and flavour were the most important factors for purchase decision. Brand and flavour showed significant association with consumer age. For most interviewed, 'nectar', 'whole' and 'natural' or '100% natural' were not well understood; they were not in accordance with the Brazilian legislation. 'Nectar', 'whole' and 'natural' or '100% natural' received a positive interpretation, whereas 'reconstituted juice' was considered a negative expression. Nevertheless, none of the labels completely conformed to the specific nutritional labelling legislation. © 2013 Institute of Food Science and Technology.

Consumer attitude towards purchasing intent for ready to drink orange juice and nectar

Purpose: The purpose of this paper was to evaluate the impact of some labeling aspects on the consumer intent to purchase ready to drink orange juice and nectar. Design/methodology/approach: The influence of label information on the consumer intent to purchase was evaluated by conjoint analysis using a convenience sample (n=149). A factorial design with four characteristics, price, brand, information about the product and kind of beverage, was used. Three levels were established for brand and product information, and two for price and kind of beverage. Findings: Low price, product information and market leading brand had positive impact. No preservatives/natural was the information that most influenced consumer's purchase intent. The ideal label showed the leading brand, low price and information no preservatives/natural. These results could be useful for strategic planning of consumer instruction and have important implications for Brazilian orange juice manufactures. Originality/value: Although the most widely consumed beverages in Brazil are ready to drink orange juice and nectar, it was unexpected that consumers did not know the differences between them and that kind of beverage was not an important factor for the purchase decision. © Emerald Group Publishing Limited.