(Table 1) 40Ar-39Ar incremental heating ages for ODP Hole 163-988A basalt and plagioclase

Results of 40Ar-39Ar Ar dating constrain the age of the submerged volcanic succession, part of the seaward-dipping reflector sequence of the Southeast Greenland volcanic rifted margin, recovered during Leg 163. At the 63ºN drilling transect, the fully normally magnetized volcanic units at Holes 989B (Unit 1) and 990A (Units 1 and 2) are dated at 57.1 ± 1.3 Ma and 55.6 ± 0.6 Ma, respectively. This correlates with a common magnetochron, C25n. The underlying, reversely magnetized lavas at Hole 990A (Units 3-13) yield an average age of 55.8 ± 0.7 Ma and may correlate with C25r. The argon data, however, are also consistent with eruption of the lavas at Site 990 during the very earliest portion of C24. If so, the normally polarized units have to be correlated to a cryptochron (e.g., C24r-11 at ~55.57 Ma). The lavas at Holes 989B and 990A have typical oceanic compositions, implying that final plate separation between Greenland and northwest Europe took place at ~56 Ma. The age for Hole 989B lava is younger than expected from the seismic interpretations, posing questions about the structural evolution of the margin. An age of 49.6 ± 0.2 Ma for the basaltic lava at Site 988 (~66ºN) points to the importance of postbreakup tholeiitic magmatism at the rifted margin. Together with results from Leg 152, a virtually complete time frame for ~12 m.y. of pre-, syn-, and postbreakup volcanism during rifted margin evolution in Southeast Greenland can now be assembled. This time frame includes continental type volcanism at ~61-60 Ma, synbreakup volcanism beginning at ~57 Ma, and postbreakup volcanism at ~49.6 Ma. These discrete time windows coincide with distinct periods of tholeiitic magmatism from the onshore East Greenland Tertiary Igneous Province and is consistent with discrete mantle-melting events triggered by plume arrival (~61-60 Ma) under central Greenland, continental breakup (~57-54 Ma), and passage of the plume axis beneath the East Greenland rifted margin after breakup (~50-49 Ma), respectively.

Anelastic strain recovery and elastic properties of ODP Leg 123 oceanic basalt samples

A knowledge of rock stress is fundamental for improving our understanding of oceanic crustal mechanisms and lithospheric dynamic processes. However, direct measurements of stress in the deep oceans, and in particular stress magnitudes, have proved to be technically difficult. Anelastic strain recovery measurements were conducted on 15 basalt core samples from Sites 765 and 766 during Leg 123. Three sets of experiments were performed: anelastic strain recovery monitoring, dynamic elastic property measurements, and thermal azimuthal anisotropy observations. In addition, a range of other tests and observations were recorded to characterize each of the samples. One common feature of the experimental results and observations is that apparently no consistent orientation trend exists, either between the different measurements on each core sample or between the same sets of measurements on the various core samples. However, some evidence of correspondence between velocity anisotropy and anelastic strain recovery exists, but this is not consistent for all the core samples investigated. Thermal azimuthal anisotropy observations, although showing no conclusive correlations with the other results, were of significant interest in that they clearly exhibited anisotropic behavior. The apparent reproducibility of this behavior may point toward the possibility of rocks that retain a "memory" of their stress history, which could be exploited to derive stress orientations from archived core. Anelastic strain recovery is a relatively new technique. Because use of the method has extended to a wider range of rock types, the literature has begun to include examples of rocks that contracted with time. Strong circumstantial evidence exists to suggest that core-sample contractions result from the slow diffusion of pore fluids from a preexisting microcrack structure that permits the rock to deflate at a greater rate than the expansion caused by anelastic strain recovery. Both expansions and contractions of the Leg 123 cores were observed. The basalt cores have clearly been intersected by an abundance of preexisting fractures, some of which pass right through the samples, but many are intercepted or terminate within the rock matrix. Thus, the behavior of the core samples will be influenced not only by the properties of the rock matrix between the fractures, but also by how these macro- and micro-scale fractures mutually interact. The strain-recovery curves recorded during Leg 123 for each of the 15 basalt core samples may reflect the result of two competing time dependent processes: anelastic strain recovery and pore pressure recovery. Were these the only two processes to influence the gauge responses, then one might expect that given the additional information required, established theoretical models might be used to determine consistent stress orientations and reliable stress magnitudes. However, superimposed upon these competing processes is their respective interaction with the preexisting fractures that intersect each core. Evidence from our experiments and observations suggests that these fractures have a dominating influence on the characteristics of the recovery curves and that their effects are complex.

(Table 1) Sulfur isotopes, total sulfur, and degree of oxidation of basalt samples from DSDP Hole 69-504B and 70-504B

About 150 basalt samples from Hole 504B, near the Costa Rica Rift were analyzed for sulfur content and sulfur-isotope composition. The basement in Hole 504B can be divided into an upper part, which has oxidative alteration (274.5-550 m below sea floor), and a lower part, which has nonoxidative alteration (550-835 m below sea floor) (the interval from 540 to 585 meters actually is transitional). This division is reflected in both the sulfur content and the sulfurisotope composition. Oxidative alteration of basalts by sea water at low temperatures has resulted in a depletion in sulfur in the upper part of the hole (mostly less than 600 ppm S) as compared to fresh sulfur-saturated oceanic tholeiites (900-1200 ppm S). High amounts of sulfur in the lower part of the hole are a result of precipitation of secondary pyrite under non-oxidative or weakly oxidative conditions from solutions which dissolved igneous sulfides. The average sulfur-isotope composition of the primary igneous sulfides is d34S = -0.01 per mil, which is close to the assumed mantle sulfur composition (d34S = 0 per mil. Pyrite and sulfate sulfur extracted together in a separate preparation step (as "pyrite-sulfate" sulfur) indicate addition of sea-water sulfate to the upper part of the basalts. The d34S of secondary pyrite isolated by hand-picking varies between -8.0 and +5.8 per mil; the "pyrite-sulfate" sulfur (d34S = -4.8 to +10.5 per mil), as well as that of the isolated pyrite, may have originated in the precipitation of pyrite from solutions containing sulfur from the dissolution of igneous sulfides, but addition of sulfur transported by hydrothermal solutions cannot be excluded.