Mechanistic studies of the photocatalytic oxidation of microcystin-LR: An investigation of byproducts of the decomposition process

Microcystins (cyclic heptapeptides) are produced by a number of freshwater cyanobacteria and cause concern in potable water supplies due to their acute and chronic toxicity. The present study reports the structural characterization of the degradation products of the photocatalytic oxidation of microcystin-LR, so aiding the mechanistic understanding of this process. TiO₂ photocatalysis is a promising technology for removal of these toxins from drinking water. However, before it can be adopted in any practical application it is necessary to have a sufficient knowledge of degradation byproducts and their potential toxicity. Liquid chromatography-mass spectrometry analysis demonstrated that the major destruction pathway of microcystin appears to be initiated via three mechanisms: UV irradiation, hydroxyl radical attack, and oxidation. UV irradiation caused geometrical isomerization of microcystin converting the (4E), (6E) of the Adda configuration to (4E), 6(Z) or 4(Z), 6(E). Hydroxyl radical attack on the conjugated diene structure of Adda moiety produced dihyroxylated products. Further oxidation cleaved the hydroxylated 4-5 and/or 6-7 bond of Adda to form aldehyde or ketone peptide residues, which then were oxidized into the corresponding carboxylic acids. Photocatalysis also hydrolyzed the peptide bond on the ring structure of microcystin to form linear structures although this appeared to be a minor pathway.

Study of oxidation and non-enzymatic glycosylation posttranslational modifications using a proteomic approach

A glicosilação não-enzimática e o stress oxidativo representam dois processos importantes visto desempenharem um papel importante no que respeita às complicações de vários processos patofisiológicos. No presente, a associação entre a glicosilação não-enzimática e a oxidação de proteínas é reconhecida como sendo um dos principais responsáveis pela acumulação de proteínas não-funcionais que, por sua vez, promove uma contínua sensibilização para um aumento do stress oxidativo ao nível celular. Embora esteja disponível bastante informação no que respeita aos dois processos e suas consequências ao nível estrutural e funcional, permanecem questões por esclarecer acerca do que se desenvolve ao nível molecular. Com o objectivo de contribuir para uma melhor compreensão da relação entre a glicosilação não-enzimática e a oxidação, proteínas modelo (albumina, insulina e histonas H2B e H1) foram submetidas a sistemas in vitro de glicosilação não-enzimática e oxidação em condições controladas e durante um período de tempo específico. A identificação dos locais de glicosilação e oxidação foi realizada através de uma abordagem proteómica, na qual após digestão enzimática se procedeu à análise por cromatografia líquida acoplada a espectrometria de massa tandem (MALDI-TOF/TOF). Esta abordagem permitiu a obtenção de elevadas taxas de cobertura das sequências proteicas, permitindo a identificação dos locais preferenciais de glicosilação e oxidação nas diferentes proteínas estudadas. Como esperado, os resíduos de lisina foram os preferencialmente glicosilados. No que respeita à oxidação, além das modificações envolvendo hidroxilações e adições de oxigénio, foram identificadas deamidações, carbamilações e conversões oxidativas específicas de vários aminoácidos. No geral, os resíduos mais afectados pela oxidação foram os resíduos de cisteína, metionina, triptofano, tirosina, prolina, lisina e fenilalanina. Ao longo do período de tempo estudado, os resultados indicaram que a oxidação teve início em zonas expostas da proteína e/ou localizadas na vizinhança de resíduos de cisteína e metionina, ao invés de exibir um comportamente aleatório, ocorrendo de uma forma nãolinear por sua vez dependente da estabilidade conformacional da proteína. O estudo ao longo do tempo mostrou igualmente que, no caso das proteínas préglicosiladas, a oxidação das mesmas ocorreu de forma mais rápida e acentuada, sugerindo que as alterações estruturais induzidas pela glicosilação promovem um estado pro-oxidativo. No caso das proteínas pré-glicosiladas e oxidadas, foi identificado um maior número de modificações oxidativas assim como de resíduos modificados na vizinhança de resíduos glicosilados. Com esta abordagem é realizada uma importante contribuição na investigação das consequências do dano ‘glico-oxidativo’ em proteínas ao nível molecular através da combinação da espectrometria de massa e da bioinformática.

Studies on Advanced Oxidation Processes for the Removal of Acetamiprid from Wastewater

Pollution of water with pesticides has become a threat to the man, material and environment. The pesticides released to the environment reach the water bodies through run off. Industrial wastewater from pesticide manufacturing industries contains pesticides at higher concentration and hence a major source of water pollution. Pesticides create a lot of health and environmental hazards which include diseases like cancer, liver and kidney disorders, reproductive disorders, fatal death, birth defects etc. Conventional wastewater treatment plants based on biological treatment are not efficient to remove these compounds to the desired level. Most of the pesticides are phyto-toxic i.e., they kill the microorganism responsible for the degradation and are recalcitrant in nature. Advanced oxidation process (AOP) is a class of oxidation techniques where hydroxyl radicals are employed for oxidation of pollutants. AOPs have the ability to totally mineralise the organic pollutants to CO2 and water. Different methods are employed for the generation of hydroxyl radicals in AOP systems. Acetamiprid is a neonicotinoid insecticide widely used to control sucking type insects on crops such as leafy vegetables, citrus fruits, pome fruits, grapes, cotton, ornamental flowers. It is now recommended as a substitute for organophosphorous pesticides. Since its use is increasing, its presence is increasingly found in the environment. It has high water solubility and is not easily biodegradable. It has the potential to pollute surface and ground waters. Here, the use of AOPs for the removal of acetamiprid from wastewater has been investigated. Five methods were selected for the study based on literature survey and preliminary experiments conducted. Fenton process, UV treatment, UV/ H2O2 process, photo-Fenton and photocatalysis using TiO2 were selected for study. Undoped TiO2 and TiO2 doped with Cu and Fe were prepared by sol-gel method. Characterisation of the prepared catalysts was done by X-ray diffraction, scanning electron microscope, differential thermal analysis and thermogravimetric analysis. Influence of major operating parameters on the removal of acetamiprid has been investigated. All the experiments were designed using central compoiste design (CCD) of response surface methodology (RSM). Model equations were developed for Fenton, UV/ H2O2, photo-Fenton and photocatalysis for predicting acetamiprid removal and total organic carbon (TOC) removal for different operating conditions. Quality of the models were analysed by statistical methods. Experimental validations were also done to confirm the quality of the models. Optimum conditions obtained by experiment were verified with that obtained using response optimiser. Fenton Process is the simplest and oldest AOP where hydrogen peroxide and iron are employed for the generation of hydroxyl radicals. Influence of H2O2 and Fe2+ on the acetamiprid removal and TOC removal by Fenton process were investigated and it was found that removal increases with increase in H2O2 and Fe2+ concentration. At an initial concentration of 50 mg/L acetamiprid, 200 mg/L H2O2 and 20 mg/L Fe2+ at pH 3 was found to be optimum for acetamiprid removal. For UV treatment effect of pH was studied and it was found that pH has not much effect on the removal rate. Addition of H2O2 to UV process increased the removal rate because of the hydroxyl radical formation due to photolyis of H2O2. An H2O2 concentration of 110 mg/L at pH 6 was found to be optimum for acetamiprid removal. With photo-Fenton drastic reduction in the treatment time was observed with 10 times reduction in the amount of reagents required. H2O2 concentration of 20 mg/L and Fe2+ concentration of 2 mg/L was found to be optimum at pH 3. With TiO2 photocatalysis improvement in the removal rate was noticed compared to UV treatment. Effect of Cu and Fe doping on the photocatalytic activity under UV light was studied and it was observed that Cu doping enhanced the removal rate slightly while Fe doping has decreased the removal rate. Maximum acetamiprid removal was observed for an optimum catalyst loading of 1000 mg/L and Cu concentration of 1 wt%. It was noticed that mineralisation efficiency of the processes is low compared to acetamiprid removal efficiency. This may be due to the presence of stable intermediate compounds formed during degradation Kinetic studies were conducted for all the treatment processes and it was found that all processes follow pseudo-first order kinetics. Kinetic constants were found out from the experimental data for all the processes and half lives were calculated. The rate of reaction was in the order, photo- Fenton>UV/ H2O2>Fenton> TiO2 photocatalysis>UV. Operating cost was calculated for the processes and it was found that photo-Fenton removes the acetamiprid at lowest operating cost in lesser time. A kinetic model was developed for photo-Fenton process using the elementary reaction data and mass balance equations for the species involved in the process. Variation of acetamiprid concentration with time for different H2O2 and Fe2+ concentration at pH 3 can be found out using this model. The model was validated by comparing the simulated concentration profiles with that obtained from experiments. This study established the viability of the selected AOPs for the removal of acetamiprid from wastewater. Of the studied AOPs photo- Fenton gives the highest removal efficiency with lowest operating cost within shortest time.

Zur Reaktionskinetik der Oxidation von Kohlenstoffmaterialien aus Biomasse

Zur Modellierung von Vergasungs- und Verbrennungsprozessen zur energetischen Nutzung von Biomasse ist die Kenntnis von reaktionskinetischen Daten für die Sauerstoff-Oxidation von Biomassepyrolysaten erforderlich. Eine ausführliche Literaturübersicht zeigt den Stand der Forschung bezüglich der experimentellen Ermittlung von reaktionskinetischen Parametern für die Oxidation von Pyrolysaten aus Lignin, Cellulose und pflanzlicher Biomasse sowie der Suche nach einem plausiblen Reaktionsmechanismus für die Reaktion von Sauerstoff mit festen Kohlenstoffmaterialien. Es wird eine Versuchsanlage mit einem quasistationär betriebenen Differentialreaktor konstruiert, die eine Messung der Reaktionskinetik und der reaktiven inneren Oberfläche (RSA) für die Reaktion eines Pyrolysats aus Maispflanzen mit Sauerstoff ermöglicht. Die getrockneten und zerkleinerten Maispflanzen werden 7 Minuten lang bei 1073 K in einem Drehrohrofen pyrolysiert. Das Pyrolysat zeichnet sich vor allem durch seine hohe Porosität von über 0,9 und seinen hohen Aschegehalt von 0,24 aus. Die RSA wird nach der Methode der Messung von Übergangskinetiken (TK) bestimmt. Die Bestimmung der RSA erfolgt für die Reaktionsprodukte CO und CO2 getrennt, für die entsprechend ermittelten Werte werden die Bezeichnungen CO-RSA und CO2-RSA eingeführt. Die Abhängigkeit dieser Größen von der Sauerstoffkonzentration läßt sich durch eine Langmuir-Isotherme beschreiben, ebenso das leichte Absinken der CO-RSA mit der Kohlendioxidkonzentration. Über dem Abbrand zeigen sich unterschiedliche Verläufe für die CO-RSA, CO2-RSA und die innere Oberfläche nach der BET-Methode. Zur Charakterisierung der Oberflächenzwischenprodukte werden temperaturprogrammierte Desorptionsversuche (TPD) durchgeführt. Die Ergebnisse zeigen, daß eine Unterscheidung in zwei Kohlenstoff-Sauerstoff-Oberflächenkomplexe ausreichend ist. Die experimentellen Untersuchungen zum Oxidationsverlauf werden im kinetisch bestimmten Bereich durchgeführt. Dabei werden die Parameter Temperatur, Sauerstoff-, CO- und CO2-Konzentration variiert. Anhand der Ergebnisse der reaktionskinetischen Untersuchungen wird ein Reaktionsmechanismus für die Kohlenstoff-Sauerstoff-Reaktion entwickelt. Dieser Reaktionsmechanismus umfaßt 7 Elementarreaktionen, für welche die reaktionskinetischen Parameter numerisch ermittelt werden. Darüber hinaus werden reaktionskinetische Parameter für einfachere massenbezogene Reaktionsgeschwindigkeitsansätze berechnet und summarische Reaktionsgeschwindigkeitsansätze für die Bildung von CO und CO2 aus dem Reaktionsmechanismus hergeleitet.

Aqueous peroxyl radical exposure to THP-1 cells causes glutathione loss followed by protein oxidation and cell death without increased caspase-3 activity

Protein oxidation within cells exposed to oxidative free radicals has been reported to occur in an uninhibited manner with both hydroxyl and peroxyl radicals. In contrast, THP-1 cells exposed to peroxyl radicals (ROO center dot) generated by thermo decomposition of the azo compound AAPH showed a distinct lag phase of at least 6 h, during which time no protein oxidation or cell death was observed. Glutathione appears to be the source of the lag phase as cellular levels were observed to rapidly decrease during this period. Removal of glutathione with buthionine sulfoxamine eliminated the lag phase. At the end of the lag phase there was a rapid loss of cellular MTT reducing activity and the appearance of large numbers of propidium iodide/annexin-V staining necrotic cells with only 10% of the cells appearing apoptotic (annexin-V staining only). Cytochrome c was released into the cytoplasm after 12 h of incubation but no increase in caspase-3 activity was found at any time points. We propose that the rapid loss of glutathione caused by the AAPH peroxyl radicals resulted in the loss of caspase activity and the initiation of protein oxidation. The lack of caspase-3 activity appears to have caused the cells to undergo necrosis in response to protein oxidation and other cellular damage. (c) 2007 Elsevier B.V. All rights reserved.

Reversal of a single base pair step controls guanine photo-oxidation by an intercalating Ru(II) dipyridophenazine complex

Small changes in DNA sequence can often have major biological effects. Here the rates and yields of guanine photo-oxidation by Λ [Ru(TAP)2(dppz)]2+ have been compared in 5′-{CCGGATCCGG}2 and 5′-{CCGGTACCGG}2 using ps/ns transient visible and time-resolved IR (TRIR) spectroscopy. The inefficiency of electron transfer in the TA sequence is consistent with the 5′-TA-3′ vs. 5′-AT-3′ binding preference predicted by X-ray crystallography. The TRIR spectra also reveal the differences in binding sites in the two oligonucleotides.

Oxidation and nitration of ribonuclease and lysozyme by peroxynitrite and myeloperoxidase

In spite of the many studies on protein modifications by reactive species, knowledge about the products resulting from the oxidation of protein-aromatic residues, including protein-derived radicals and their stable products, remains limited. Here, we compared the oxidative modifications promoted by peroxynitrite and myeloperoxidase/hydrogen peroxide/nitrite in two model proteins, ribonuclease (6Tyr) and lysozyme (3Tyr/6Trp). The formation of protein-derived radicals and products was higher at pH 5.4 and 7.4 for myeloperoxidase and peroxynitrite, respectively. The main product was 3-nitro-Tyr for both proteins and oxidants. Lysozyme rendered similar yields of nitro-Trp, particularly when oxidized by peroxynitrite. Hydroxylated and dimerized products of Trp and Tyr were also produced, but in lower yields. Localization of the main modified residues indicates that peroxynitrite decomposes to radicals within the proteins behaving less specifically than myeloperoxidase. Nitrogen dioxide is emphasized as an important protein modifier. (C) 2009 Elsevier Inc. All rights reserved.

Peroxymonocarbonate and Carbonate Radical Displace the Hydroxyl-like Oxidant in the Sod1 Peroxidase Activity under Physiological Conditions

Despite being one of the most important antioxidant defenses, Cu,Zn-superoxide dismutase (Sod1) has been frequently associated with harmful effects, including neurotoxicity. This toxicity has been attributed to immature forms of Sod1 and extraneous catalytic activities. Among these, the ability of Sod1 to function as a peroxidase may be particularly relevant because it is increased in bicarbonate buffer and produces the reactive carbonate radical. Despite many studies, how this radical forms remains unknown. To address this question, we systematically studied hSod1 peroxidase activity in the presence of nitrite, formate, and bicarbonate-carbon dioxide. Kinetic analyses of hydrogen peroxide consumption and of nitrite, formate, and bicarbonate-carbon dioxide oxidation showed that the Sod1-bound hydroxyl-like oxidant functions in the presence of nitrite and formate. In the presence of bicarbonate-carbon dioxide, this oxidant is replaced by peroxymonocarbonate, which is then reduced to the carbonate radical. Peroxymonocarbonate intermediacy was evidenced by (13)C NMR experiments showing line broadening of its peak in the presence of Zn,ZnSod1. In agreement, peroxymonocarbonate was docked into the hSod1 active site, where it interacted with the conserved Arg(143). Also, a reaction between peroxymonocarbonate and Cu(I)Sod1 was demonstrated by stopped-flow experiments. Kinetic simulations indicated that peroxymonocarbonate is produced during Sod1 turnover and not in bulk solution. In the presence of bicarbonate-carbon dioxide, sustained hSod1-mediated oxidations occurred with low steady-state concentrations of hydrogen peroxide (4-10 mu M). Thus, carbonate radical formation through peroxymonocarbonate may be a key event in Sod1-induced toxicity.

Effect of flavonoids on 2 `-deoxyguanosine and DNA oxidation caused by singlet molecular oxygen

Antioxidant potential is generally investigated by assaying the ability of a compound to protect biological systems from free radicals. However, non-radical reactive oxygen species can also be harmful. Singlet molecular oxygen ((1)O(2)) is generated by energy transfer to molecular oxygen. The resulting (1)O(2) is able to oxidize the nucleoside 2`-deoxyguanosine (dGuo), which leads to the formation of 8-oxo-7,8-dihydro-2`-deoxyguanosine (8-oxodGuo) and spiroiminodihydantoin 2`-deoxyribonucleoside diastereomers (dSp) in an aqueous solution. The main objective of the present study was to verify whether the presence of flavonoids (flavone, apigenin, quercetin, morin and catechin) at different concentrations could protect dGuo from (1)O(2) damage. Of the tested flavonoids, flavone possessed antioxidant activity, as determined by a decrease in the formation of both products. Apigenin, morin, quercetin and catechin all increased the formation of 8-oxodGuo at a concentration of 100 mu M. The quantification of plasmid strand breaks after treatment with formamidopyrimidine-DNA glycosylase showed that flavone protected and quercetin and catechin enhanced DNA oxidation. Our results show that compounds, such as flavonoids, may affect the product distribution of (1)O(2)-mediated oxidation of dGuo, and, in particular, high concentrations of flavonoids with hydroxyl groups in their structure lead to an increase in the formation of the mutagenic lesion 8-oxodGuo. (C) 2010 Elsevier Ltd. All rights reserved.

Electrochemical oxidation of an acid dye by active chlorine generated using Ti/Sn(1-x)Ir O-x(2) electrodes

The generation of active chlorine on Ti/Sn(1-x)Ir (x) O-2 anodes, with different compositions of Ir (x = 0.01, 0.05, 0.10 and 0.30 ), was investigated by controlled current density electrolysis. Using a low concentration of chloride ions (0.05 mol L-1) and a low current density (5 mA cm(-2)) it was possible to produce up to 60 mg L-1 of active chlorine on a Ti/Sn0.99Ir0.01O2 anode. The feasibility of the discoloration of a textile acid azo dye, acid red 29 dye (C.I. 16570), was also investigated with in situ electrogenerated active chlorine on Ti/Sn(1-x)Ir (x) O-2 anodes. The best conditions for 100% discoloration and maximum degradation (70% TOC reduction) were found to be: NaCl pH 4, 25 mA cm(-2) and 6 h of electrolysis. It is suggested that active chlorine generation and/or powerful oxidants such as chlorine radicals and hydroxyl radicals are responsible for promoting faster dye degradation. Rate constants calculated from color decay versus time reveal a zero order reaction at dye concentrations up to 1.0 x 10(-4) mol L-1. Effects of other electrolytes, dye concentration and applied density currents also have been investigated and are discussed.

Ethanol electro-oxidation in an alkaline medium using Pd/C, Au/C and PdAu/C electrocatalysts prepared by electron beam irradiation

Carbon-supported Pd, Au and bimetallic PdAu (Pd:Au 90:10, 50:50 and 30:70 atomic ratios) electrocatalysts were prepared using electron beam irradiation. The obtained materials were characterized by energy dispersive X-ray analysis (EDX), X-ray diffraction (XRD) and transmission electron microscopy (TEM), and their catalytic activities toward ethanol electro-oxidation were evaluated in an alkaline medium using electrochemical techniques, in situ attenuated total reflectance Fourier transformed infrared spectroscopy (ATR-FTIR) analysis and a single alkaline direct ethanol fuel cell (ADEFC). EDX analyses showed that the actual Pd: Au atomic ratios were very similar to the nominal ones. X-ray diffractograms of PdAu/C electrocatalysts evidenced the presence of Pd-rich (fcc) and Au-rich (fcc) phases. TEM analysis showed a homogeneous dispersion of nanoparticles on the carbon support, with an average size in the range of 3-5 nm and broad size distributions. Cyclic voltammetry (CV) and chronoamperometry (CA) experiments revealed the superior ambient activity toward ethanol electro-oxidation of PdAu/C electrocatalysts with Pd: Au ratios of 90:10 and 50:50. In situ ATR-FTIR spectroscopy measurements have shown that the mechanism for ethanol electro-oxidation is dependent on catalyst composition, leading to different reaction products, such as acetaldehyde and acetate, depending on the number of electrons transferred. Experiments on a single ADEFC were conducted between 50 and 900 C, and the best performance of 44 mW cm-2 in 2.0molL-1 ethanol was obtained at 850C for the Pd:Au 90:10 catalysts. This superior performance is most likely associated with enhancement of ethanol adsorption on Pd, oxidation of the intermediates, the presence of gold oxide-hydroxyl species, low mean particle diameters and better distribution of particles on the support. © 2013 Elsevier Ltd. All rights reserved.

Electrocatalytic effect of Pb and Sn adatoms on the oxidation of 1-propanol on platinized platinum electrodes: Determination of the apparent activation energy

The electrocatalytic oxidation of 1-propanol was investigated on platinum electrodes modified by submonolayers of Pb and Sn in acid media. An increase of oxidation rates observed for both Pb and Sn, and the influence of theta values was investigated. The values of the apparent activation energy evaluated from the Arrhenius plots concerning the electrochemical oxidation of 1-propanol on modified platinzed platinum electrodes, reveal a significant decrease in the presence of upd Sn and Ph adatoms. A decrease from 56 to 26 U mol(-1) in the presence of Sn. and from 78 to 25 U mol(-1) for Ph adatoms are some illustrative values which reflect the promoting effect of the upd adatoms.

Photo-Fenton oxidation of phenol and organochlorides (2,4-DCP and 2,4-D) in aqueous alkaline medium with high chloride concentration

A highly concentrated aqueous saline-containing solution of phenol, 2,4-dichlorophenoxyacetic acid (2,4-D) and 2,4-dichlorophenol (2.4-DCP) was treated by the photo-Fenton process in a system composed of an annular reactor with a quartz immersion well and a medium-pressure mercury lamp (450 W). The study was conducted under special conditions to minimize the costs of acidification and neutralization, which are usual steps in this type of process. Photochemical reactions were carried out to investigate the influence of some process variables such as the initial concentration of Fe2+ ([Fe2+](0)) from 1.0 up to 2.5 mM, the rate in mmol of H2O2 fed into the system (F-H2O2,F-in) from 3.67 up to 7.33 mmol of H2O2/min during 120 min of reaction time, and the initial pH (pH(0)) from 3.0 up to 9.0 in the presence and absence of NaCl (60.0 g/L). Although the optimum pH for the photo-Fenton process is about 3.0, this particular system performed well in experimental conditions starting at alkaline and neutral pH. The results obtained here are promising for industrial applications, particularly in view of the high concentration of chloride, a known hydroxyl radical scavenger and the main oxidant present in photo-Fenton processes. (C) 2012 Elsevier Ltd. All rights reserved.

ESTIMATING REACTION CONSTANTS BY AB INITIO MOLECULAR MODELING: A STUDY ON THE OXIDATION OF PHENOL TO CATECHOL AND HYDROQUINONE IN ADVANCED OXIDATION PROCESSES

Molecular modeling is growing as a research tool in Chemical Engineering studies, as can be seen by a simple research on the latest publications in the field. Molecular investigations retrieve information on properties often accessible only by expensive and time-consuming experimental techniques, such as those involved in the study of radical-based chain reactions. In this work, different quantum chemical techniques were used to study phenol oxidation by hydroxyl radicals in Advanced Oxidation Processes used for wastewater treatment. The results obtained by applying a DFT-based model showed good agreement with experimental values available, as well as qualitative insights into the mechanism of the overall reaction chain. Solvation models were also tried, but were found to be limited for this reaction system within the considered theoretical level without further parameterization.

Hydroxyl scavenging activity accounts for differential antioxidant protection of Plantago major against oxidative toxicity in isolated rat liver mitochondria

Objectives The aim of this work was to study the effects of P. major against the oxidative damage of isolated rat liver mitochondria. Methods The extracts were obtained using methanol (MeOH), ethyl acetate (EAc), dichloromethane (DCM), and hexane (Hex) as solvents. Key findings Hex, DCM, and EAc totally, and MeOH partially, inhibited ROS generation and lipid peroxidation of membranes induced by Fe2+ or t-BOOH. However, only MeOH was able to prevent the t-BOOH-induced glutathione and NAD(P)H oxidation. All extracts chelated Fe2+ and reduced DPP Hradicals. EPR analysis revealed that P. major exhibited potent scavenger activity for hydroxyl radicals. Conclusions The potent antioxidant activity exhibited by P. major was able to prevent oxidative mitochondrial damage, contributing to the understanding of its hepatoprotective action against ROS-mediated toxicity.