Estudi i simulació aerodinàmica amb programari de dinàmica de fluids computacional (CFD) en un model bàsic de vehicle de competició de la categoria CM (curses de muntanya)

Aquest projecte té com a objectiu la simulació numérica de la carrosseria d’ un vehicle de curses de muntanya de categoria CM

Uso de hardware de código fonte aberto "Arduino" para acionamento de dispositivo solenoide em sistemas de análises em fluxo

This paper describes the use of the open source hardware platform, denominated "Arduino", for controlling solenoid valves for solutions handling in flow analysis systems. System assessment was carried out by spectrophotometric determination of iron (II) in natural water. The sampling rate was estimated as 45 determinations per hour and the coefficient of variation was lower than 3%. Per determination, 208 µg of 1-10-phenanthroline and ascorbic acid were consumed, generating 1.3 mL of waste. "Arduino" proved a reliable microcontroller with low cost and simple interfacing, allowing USB communication for solenoid device switching in flow systems.

CFD Simulation of Two-phase and Three-phase Flows in Internal-loop Airlift

Airlift reactors are pneumatically agitated reactors that have been widely used in chemical, petrochemical, and bioprocess industries, such as fermentation and wastewater treatment. Computational Fluid Dynamics (CFD) has become more popular approach for design, scale-up and performance evaluation of such reactors. In the present work numerical simulations for internal-loop airlift reactors were performed using the transient Eulerian model with CFD package, ANSYS Fluent 12.1. The turbulence in the liquid phase is described using κ- ε the model. Global hydrodynamic parameters like gas holdup, gas velocity and liquid velocity have been investigated for a range of superficial gas velocities, both with 2D and 3D simulations. Moreover, the study of geometry and scale influence on the reactor have been considered. The results suggest that both, geometry and scale have significant effects on the hydrodynamic parameters, which may have substantial effects on the reactor performance. Grid refinement and time-step size effect have been discussed. Numerical calculations with gas-liquid-solid three-phase flow system have been carried out to investigate the effect of solid loading, solid particle size and solid density on the hydrodynamic characteristics of internal loop airlift reactor with different superficial gas velocities. It was observed that averaged gas holdup is significantly decreased with increasing slurry concentration. Simulations show that the riser gas holdup decreases with increase in solid particle diameter. In addition, it was found that the averaged solid holdup increases in the riser section with the increase of solid density. These produced results reveal that CFD have excellent potential to simulate two-phase and three-phase flow system.

Kuulakekoreaktorin sydämen jäähdytevirtauksen CFD-mallinnus

Kandidaatintyössä luotiin CFD-malli mallintamaan jäähdytevirtausta kuulakekoreaktorin sydämessä käyttämällä Ansys Fluent -ohjelmaa. Mallin avulla tarkasteltiin virtauksen käyttäymistä ja painehäviötä ja saatuja tuloksia verrattiin aiempiin tutkimuksiin. Kandidaatin työssä on myös kerrottu mallintamisen etenemisestä ja laskentateoriaa.

CFD Modelling of Direct Contact Condensation in Suppression Pools by Applying Condensation Models of Separated Flow

The condensation rate has to be high in the safety pressure suppression pool systems of Boiling Water Reactors (BWR) in order to fulfill their safety function. The phenomena due to such a high direct contact condensation (DCC) rate turn out to be very challenging to be analysed either with experiments or numerical simulations. In this thesis, the suppression pool experiments carried out in the POOLEX facility of Lappeenranta University of Technology were simulated. Two different condensation modes were modelled by using the 2-phase CFD codes NEPTUNE CFD and TransAT. The DCC models applied were the typical ones to be used for separated flows in channels, and their applicability to the rapidly condensing flow in the condensation pool context had not been tested earlier. A low Reynolds number case was the first to be simulated. The POOLEX experiment STB-31 was operated near the conditions between the ’quasi-steady oscillatory interface condensation’ mode and the ’condensation within the blowdown pipe’ mode. The condensation models of Lakehal et al. and Coste & Lavi´eville predicted the condensation rate quite accurately, while the other tested ones overestimated it. It was possible to get the direct phase change solution to settle near to the measured values, but a very high resolution of calculation grid was needed. Secondly, a high Reynolds number case corresponding to the ’chugging’ mode was simulated. The POOLEX experiment STB-28 was chosen, because various standard and highspeed video samples of bubbles were recorded during it. In order to extract numerical information from the video material, a pattern recognition procedure was programmed. The bubble size distributions and the frequencies of chugging were calculated with this procedure. With the statistical data of the bubble sizes and temporal data of the bubble/jet appearance, it was possible to compare the condensation rates between the experiment and the CFD simulations. In the chugging simulations, a spherically curvilinear calculation grid at the blowdown pipe exit improved the convergence and decreased the required cell count. The compressible flow solver with complete steam-tables was beneficial for the numerical success of the simulations. The Hughes-Duffey model and, to some extent, the Coste & Lavi´eville model produced realistic chugging behavior. The initial level of the steam/water interface was an important factor to determine the initiation of the chugging. If the interface was initialized with a water level high enough inside the blowdown pipe, the vigorous penetration of a water plug into the pool created a turbulent wake which invoked the chugging that was self-sustaining. A 3D simulation with a suitable DCC model produced qualitatively very realistic shapes of the chugging bubbles and jets. The comparative FFT analysis of the bubble size data and the pool bottom pressure data gave useful information to distinguish the eigenmodes of chugging, bubbling, and pool structure oscillations.

SolidWorks Simulations ja Femap FE-analyysiohjelmien vertailu RHS-putkipalkkien mallinnuksen avulla

Tässä kandidaatintyössä vertailtiin SolidWorks Simulations ja Femap FE-analyysiohjelmien tuottamia tuloksia. Vertailu suoritettiin yksinkertaisten RHS-putkipalkkien mallinnuksen avulla. Mallinnuksessa käytettiin viittä erilaista kuormitustapausta, jotka sisälsivät mm. taivutus-, vääntö- ja jännityskeskittymätarkastelut. Ohjelmien tuottamia tuloksia verrattiin mahdollisuuksien mukaan analyyttisin menetelmin tehtyihin vertailulaskelmiin. Työn tarkoituksena oli selvittää tuottivatko eri ohjelmat erilaisia tuloksia samoista kuormitustapauksista ja kuinka paljon tulokset erosivat.

Uraaniheksafluoridin faasimuutoksen CFD-mallinnus

Diplomityön tarkoituksena on luoda uraaniheksafluoridista käyttäjän määrittelemä aine kaupallisen virtauslaskentaohjelmiston (FLUENT) ainekirjastoon ja simuloida aineen käyttäytymistä sulaessa ja kiinteyttäessä. Työn kirjallisuusosassa on esitelty aiempia tutkimuksia uraaniheksafluoridin termodynaamisista ominaisuuksista, joita käytetään aineen määrittelyssä. Kokeellisessa osassa on käytetty virtauslaskentaohjelmiston Eulerilaista monifaasimallia sulamisen ja kiinteytymisen tarkasteluun kaksidimensionaalisessa sylinterissä.

Kaasujäähdytteinen nopea reaktori – Virtauskanavan painehäviö CFD-laskennalla

Kandidaatintyössä tarkastellaan kaasujäähdytteistä nopeaa reaktoria, joka on yksi monista tulevaisuuden ydinvoimalaitosten konsepteista. Aluksi esitellään lyhyesti kaupalliset reaktorisukupolvet ja tulevan neljännen sukupolven tärkeimmät linjaukset. Teoriaosuudessa esitellään CFD-laskennan pääperiaatteet ja käsitellään hieman turbulenssin mallinnusta ja työssä käytettyä OpenFOAM-ohjelmistoa. Työhön liittyy CFD-laskenta, jossa polttoaineen virtauskanavan painehäviö lasketaan eri ripakonstruktioilla. Simulaatioiden perusteella pohditaan myös turbulenttisen virtauksen vaikutusta lämmönsiirron tehokkuuteen. Tarkkoja mittauksia ja CFDlaskentoja tarvitaan, jotta voidaan tehdä tarkkoja korrelaatioita painehäviöille ja lämmönsiirtokertoimille termohydrauliikan mallinnusohjelmia varten.

CFD modeling of dispersion water feed in wastewater cleaning application

Fluid particle breakup and coalescence are important phenomena in a number of industrial flow systems. This study deals with a gas-liquid bubbly flow in one wastewater cleaning application. Three-dimensional geometric model of a dispersion water system was created in ANSYS CFD meshing software. Then, numerical study of the system was carried out by means of unsteady simulations performed in ANSYS FLUENT CFD software. Single-phase water flow case was setup to calculate the entire flow field using the RNG k-epsilon turbulence model based on the Reynolds-averaged Navier-Stokes (RANS) equations. Bubbly flow case was based on a computational fluid dynamics - population balance model (CFD-PBM) coupled approach. Bubble breakup and coalescence were considered to determine the evolution of the bubble size distribution. Obtained results are considered as steps toward optimization of the cleaning process and will be analyzed in order to make the process more efficient.

Arduino-pohjainen OBD2-lukija SAE J1850 VPW protokollatuella

Kandidaatintyössä toteutetaan OBD2 (On-Board Diagnostics 2) -lukija ajoneuvon päästöjenhallintajärjestelmän diagnostiikkatiedoille yleiskäyttöisellä mikro-ohjaimella. Lukija tukee tiedonsiirtoprotokollana SAE J1850 VPW protokollaa. Mikro-ohjaimena on Atmel Corporationin AVR ATMega328. Työn tavoitteena on havainnoida vastaantulevia käytännön ongelmia ja haasteita mikro-ohjaimen käytöllä tiedonsiirtoprotokollan toteutukseen, ja verrata toteutettua järjestelmää kaupallisiin OBD2-lukijoihin. Työn johtopäätöksenä havaitaan mikro-ohjaimen suorituskyvyn rajoitteet ja sen tuomat toiminnan epävarmuustekijät. Työssä myös todetaan, että mikro-ohjain soveltuu tiedonsiirtoprotokollan toteutukseen kun rajoitteet otetaan huomioon. Kaupallisiin lukijoihin verrattuna yleiskäyttöiseen mikro-ohjaimeen perustuva toteutettu järjestelmä on kalliimpi ja toiminnoiltaan suppeampi. Mikro-ohjaimeen perustuva järjestelmä on kuitenkin muokattavissa ja laajennettavissa tarvittaessa, jolloin toteutukseen voidaan saada kaupallisista järjestelmistä mahdollisesti puuttuvia ominaisuuksia, kuten valmistajakohtaisia protokollia ja toimintoja, joita ei ole määritelty OBD2:ssa. Yhtenä esimerkkinä tällaisesta toiminnosta voi mainita ajoneuvoissa yleistyvän sähköisen käsijarrun säätöä ohjaavat komennot jarruhuoltoa varten.

Using Computational Fluid-Dynamics (CFD) for the evaluation of beer pasteurization: effect of orientation of cans

In-package pasteurization is the most used method for beer microbiological stabilization. The search for safer and better quality food has created a need to better understand the processes involved in producing it. However, little is known about the temperature and velocity profiles during the thermal processes of liquid foods in commercial packaging, which results in over-dimensioned processes to guarantee safety, decreasing the sensorial and nutritional characteristics of the product and increasing process costs. Simulations using Computational Fluid-Dynamics (CFD) have been used by various authors to evaluate those processes. The objective of the present paper was to evaluate the effect of packaging orientation in the pasteurization of beer in a commercial aluminum can using CFD. A heating process was simulated at 60 ºC up to 15 PUs (a conventional beer process, in which 1 Pasteurization Unit (PU) is equivalent to 1minute at 60 ºC). The temperature profile and convection current velocity along the process and the variation of the PUs were evaluated in relation to time considering the cans in the conventional, inverted, and horizontal positions. The temperature and velocity profiles were similar to those presented in the literature. The package position did not result in process improvement.

Descripción del proceso de colada continua mediante CFD.

Tesis (Maestría en Ciencias de la Ingeniería Mecánica con Especialidad en Materiales) UANL, 2010.

CFD Simulation of Multiphase Reactors

Regional Research Laboratory

Techniques for Enhancing Wind Energy Generation - A CFD Based Multibody Dynamics Approach in Horizontal Axis Wind Turbines

Wind energy has emerged as a major sustainable source of energy.The efficiency of wind power generation by wind mills has improved a lot during the last three decades.There is still further scope for maximising the conversion of wind energy into mechanical energy.In this context,the wind turbine rotor dynamics has great significance.The present work aims at a comprehensive study of the Horizontal Axis Wind Turbine (HAWT) aerodynamics by numerically solving the fluid dynamic equations with the help of a finite-volume Navier-Stokes CFD solver.As a more general goal,the study aims at providing the capabilities of modern numerical techniques for the complex fluid dynamic problems of HAWT.The main purpose is hence to maximize the physics of power extraction by wind turbines.This research demonstrates the potential of an incompressible Navier-Stokes CFD method for the aerodynamic power performance analysis of horizontal axis wind turbine.The National Renewable Energy Laboratory USA-NREL (Technical Report NREL/Cp-500-28589) had carried out an experimental work aimed at the real time performance prediction of horizontal axis wind turbine.In addition to a comparison between the results reported by NREL made and CFD simulations,comparisons are made for the local flow angle at several stations ahead of the wind turbine blades.The comparison has shown that fairly good predictions can be made for pressure distribution and torque.Subsequently, the wind-field effects on the blade aerodynamics,as well as the blade/tower interaction,were investigated.The selected case corresponded to a 12.5 m/s up-wind HAWT at zero degree of yaw angle and a rotational speed of 25 rpm.The results obtained suggest that the present can cope well with the flows encountered around wind turbines.The areodynamic performance of the turbine and the flow details near and off the turbine blades and tower can be analysed using theses results.The aerodynamic performance of airfoils differs from one another.The performance mainly depends on co-efficient of performnace,co-efficient of lift,co-efficient of drag, velocity of fluid and angle of attack.This study shows that the velocity is not constant for all angles of attack of different airfoils.The performance parameters are calculated analytically and are compared with the standardized performance tests.For different angles of ,the velocity stall is determined for the better performance of a system with respect to velocity.The research addresses the effect of surface roughness factor on the blade surface at various sections.The numerical results were found to be in agreement with the experimental data.A relative advantage of the theoretical aerofoil design method is that it allows many different concepts to be explored economically.Such efforts are generally impractical in wind tunnels because of time and money constraints.Thus, the need for a theoretical aerofoil design method is threefold:first for the design of aerofoil that fall outside the range of applicability of existing calalogs:second,for the design of aerofoil that more exactly match the requirements of the intended application:and third,for the economic exploration of many aerofoil concepts.From the results obtained for the different aerofoils,the velocity is not constant for all angles of attack.The results obtained for the aerofoil mainly depend on angle of attack and velocity.The vortex generator technique was meticulously studies with the formulation of the specification for the right angle shaped vortex generators-VG.The results were validated in accordance with the primary analysis phase.The results were found to be in good agreement with the power curve.The introduction of correct size VGs at appropriate locations over the blades of the selected HAWT was found to increase the power generation by about 4%