Finite element modeling of straightening of thin-walled seamless tubes of austenitic stainless steel

During this thesis work a coupled thermo-mechanical finite element model (FEM) was builtto simulate hot rolling in the blooming mill at Sandvik Materials Technology (SMT) inSandviken. The blooming mill is the first in a long line of processes that continuously or ingotcast ingots are subjected to before becoming finished products. The aim of this thesis work was twofold. The first was to create a parameterized finiteelement (FE) model of the blooming mill. The commercial FE software package MSCMarc/Mentat was used to create this model and the programing language Python was used toparameterize it. Second, two different pass schedules (A and B) were studied and comparedusing the model. The two pass series were evaluated with focus on their ability to healcentreline porosity, i.e. to close voids in the centre of the ingot. This evaluation was made by studying the hydrostatic stress (σm), the von Mises stress (σeq)and the plastic strain (εp) in the centre of the ingot. From these parameters the stress triaxiality(Tx) and the hydrostatic integration parameter (Gm) were calculated for each pass in bothseries using two different transportation times (30 and 150 s) from the furnace. The relationbetween Gm and an analytical parameter (Δ) was also studied. This parameter is the ratiobetween the mean height of the ingot and the contact length between the rolls and the ingot,which is useful as a rule of thumb to determine the homogeneity or penetration of strain for aspecific pass. The pass series designed with fewer passes (B), many with greater reduction, was shown toachieve better void closure theoretically. It was also shown that a temperature gradient, whichis the result of a longer holding time between the furnace and the blooming mill leads toimproved void closure.

Initiation and early crack growth in VHCF of stainless steels : Experimental and theoretical analysis

Mechanical fatigue is a failure phenomenon that occurs due to repeated application of mechanical loads. Very High Cycle Fatigue (VHCF) is considered as the domain of fatigue life greater than 10 million load cycles. Increasing numbers of structural components have service life in the VHCF regime, for instance in automotive and high speed train transportation, gas turbine disks, and components of paper production machinery. Safe and reliable operation of these components depends on the knowledge of their VHCF properties. In this thesis both experimental tools and theoretical modelling were utilized to develop better understanding of the VHCF phenomena. In the experimental part, ultrasonic fatigue testing at 20 kHz of cold rolled and hot rolled stainless steel grades was conducted and fatigue strengths in the VHCF regime were obtained. The mechanisms for fatigue crack initiation and short crack growth were investigated using electron microscopes. For the cold rolled stainless steels crack initiation and early growth occurred through the formation of the Fine Granular Area (FGA) observed on the fracture surface and in TEM observations of cross-sections. The crack growth in the FGA seems to control more than 90% of the total fatigue life. For the hot rolled duplex stainless steels fatigue crack initiation occurred due to accumulation of plastic fatigue damage at the external surface, and early crack growth proceeded through a crystallographic growth mechanism. Theoretical modelling of complex cracks involving kinks and branches in an elastic half-plane under static loading was carried out by using the Distributed Dislocation Dipole Technique (DDDT). The technique was implemented for 2D crack problems. Both fully open and partially closed crack cases were analyzed. The main aim of the development of the DDDT was to compute the stress intensity factors. Accuracy of 2% in the computations was attainable compared to the solutions obtained by the Finite Element Method.

Análise de componentes principais aplicada a ruído eletroquímico

Neste trabalho foi utilizado um método matemático para classificar registros de potencial e corrente de ensaios de corrosão na técnica de amperimetria de resistência nula (ZRA). Foi aplicado o método estatístico de múltiplas variáveis simples chamado Análise dos Componentes Principais (PCA), cujo objetivo principal foi identificar padrões nestes dados de ruído eletroquímico. Foram testados o aço carbono UNS G10200, os aços inoxidáveis austenítico UNS S31600 e o superduplex UNS S32750 em meios de ácido sulfúrico (5% H2SO4), cloreto férrico (0,1 mol/L FeCl3) e hidróxido de sódio (0,1% NaOH). Os ensaios foram replicados com oito repetições para se ter reprodutibilidade e conhecimento dos aspectos estatísticos envolvidos. Os resultados mostraram que a análise de componentes principais pode ser utilizada como uma ferramenta para analisar sinais de ruído eletroquímico, identificando os clusters dos comportamentos potencial-tempo, corrente-tempo e acessoriamente identificar os outliersdos registros temporais.

Análise morfológica da corrosão por pites em aço inoxidável austenítico AISI 310S submetido à exposição em névoa salina

O artigo teve como objetivo estudar a evolução do crescimento, distribuição e classificação dos pites em aços inoxidáveis austeníticos AISI 310S no estado como recebida e tratado termicamente, submetidos a diferentes tempos de exposição em meio salino. A aplicabilidade deste trabalho baseou-se no desenvolvimento de uma técnica para caracterização morfológica da corrosão localizada, associado com os aspectos de descrição de formas, tamanho, parâmetros específicos e populacionais. A metodologia consistiu nas seguintes etapas: preparação dos corpos de prova, testes de corrosão via névoa salina em diferentes condições, análise microestrutural, análise dos perfis dos pites, processamento digital e análise de imagens, visando caracterizar a distribuição, morfologia e o tamanho dos pites. Os resultados obtidos no processamento digital e análise de imagens dos perfis foram submetidos á análise estatística, utilizando à mediana como parâmetro de avaliação na liga como recebido e tratada. A liga como recebido, exibe a seguinte morfologia: pites hemisféricos> região de transição A> região de transição B> irregulares> cônicos. A quantidade de pites na liga tratada a cada tempo de exposição é: região de transição B> hemisféricos> região de transição A> cônicos> irregulares.

Análise morfológica de pites em aços inoxidáveis austeníticos ABNT 304 e 310S submetido à nèvoa salina

Pós-graduação em Engenharia Mecânica - FEG

Colonización bacteriana y oxidación de aceros inoxidables austeníticos, ferríticos y dúplex sinterizados

Las características y capacidades de los aceros inoxidables sinterizados se han investigado en una doble vertiente. Por una parte con vista a sus capacidades de resistencia a la oxidación en caliente y por otra parte se ha investigado su capacidad para retener microorganismos que contribuyan a la descontaminación de un ambiente. Por ello, para cada una de estas funciones se han utilizado los aceros inoxidables sinterizados, que se han considerado más adecuados. Para estudiar sus capacidades de resistencia a la oxidación en caliente se ha utilizado un acero inoxidable austenítico AISI 304L, un acero inoxidable ferrítico AISI 430L y un acero inoxidable Fe-16Cr-3Al. Para estudiar sus capacidades para retener microorganismos se ha utilizado un acero inoxidable austenítico AISI 316L, un acero inoxidable ferrítico AISI 430L y un acero inoxidable dúplex 50%/50% de los anteriores. Para esta última finalidad los aceros se han compactado a tres diferentes presiones 300, 500 y 700 MPa, a las que corresponden diferentes porosidades. En relación con el comportamiento frente a la oxidación en caliente, se han cuantificado los incrementos positivos o negativos de volumen, masa y densidad en los diferentes tipos de sinterización y estados de tratamiento de oxidación. Como tónica general de comportamiento, puede decirse que los aceros sinterizados bajo vacío son más resistentes a la oxidación, que los sinterizados en atmósfera de N2-5H2 y que los aceros inoxidables austeníticos son algo más resistentes, que los Cr-Al y estos, a su vez, más que los aceros inoxidables ferríticos. Respecto a la retención de microorganismos, los tres aceros inoxidables sinterizados se han ensayado en diferentes medios de cultivo, utilizando cuatro especies de bacterias. Los mejores resultados se han obtenido con Staphylococcus aureus, muy favorable para su observación y recuento. Se han cuantificado, una vez sinterizados y colonizados por los microorganismos, para cada material y presión de compactación, las áreas de cada uno de los poros y el número de microorganismos situados en los poros y en la superficie sin poros. Se ha establecido en cada caso la densidad de microorganismos en las zonas de poros y en las zonas sin poros. Como tónica general puede decirse, que los aceros inoxidables austeníticos aparecen más favorables para estos estudios, que los aceros dúplex y estos más que los inoxidables ferríticos. Asimismo, se desprende que las áreas de los poros dependen de forma unívoca de la presión de compactación y que para áreas de poros decrecientes las densidades de microorganismos son crecientes. En consecuencia, podría deducirse, que a igualdad de área de poros en una superficie, aquella que tuviera los poros más pequeños, retendría mayor cantidad de bacterias. ABSTRACT The characteristics and capacities of sintered stainless steels have been researched from two perspectives: firstly, with a view to their resistance to hot oxidation, and secondly their capacity to retain microorganisms able to decontaminate the environment. For both these functions, sintered stainless steels were used, which are considered to be the most fit for purpose. To study their resistance to hot oxidation, we used austenitic stainless steel AISI 304L, ferritic stainless steel AISI 430L and stainless steel Fe-16Cr-3Al. To study their ability to retain microorganisms, we used austenitic stainless steel AISI 316L, ferritic stainless steel AISI 430L, and duplex stainless steel, being a 50/50 blend of the two former ones. For this last purpose, the steels were compacted at three different pressures (300, 500 and 700 MPa) corresponding to different porosities. With regard to the hot oxidation, we quantified the positive or negative increments in volume, mass and density in the different types of sintering and oxidation treatment states. As a general performance trend, we observed that vacuum sintered steels are more resistant to oxidation than those sintered in an atmosphere of N2-5H2, and that austenitic stainless steels are slightly more resistant than the Cr-Al steels which, in turn, are more resistant than the ferritic stainless steels. With regard to the retention of microorganisms, the three sintered stainless steels were tested in different culture media using four types of bacteria. The best results for observation and counting were obtained with Staphylococcus aureus bacteria. Once sintered and colonized by microorganisms, for each material and compacting pressure we quantified the areas of the pores and the number of microorganisms situated in the pores and on the pore-free surface. In each case, the density of microorganisms in the pores and in the pore-free areas was established. As a general rule, we can say that the austenitic stainless steels appear to be more favourable for this type of study than the duplex steels which, in turn, are more favourable than the ferritic stainless steels. It also emerged that the areas with the pores depend unequivocally on the compacting pressure, and that the smaller the area of the pore the higher the density of the microorganisms. Consequently, it can be deduced that comparing an equal area of pores on a surface, the one with the smaller pores would retain a larger number of bacteria.

Microstructure characterization of 316L deformed at high strain rates using EBSD

Specimens from split Hopkinson pressure bar experiments, at strain rates between ~ 1000–9000 s− 1 at room temperature and 500 °C, have been studied using electron backscatter diffraction. No significant differences in the microstructures were observed at different strain rates, but were observed for different strains and temperatures. Size distribution for subgrains with boundary misorientations > 2° can be described as a bimodal lognormal area distribution. The distributions were found to change due to deformation. Part of the distribution describing the large subgrains decreased while the distribution for the small subgrains increased. This is in accordance with deformation being heterogeneous and successively spreading into the undeformed part of individual grains. The variation of the average size for the small subgrain distribution varies with strain but not with strain rate in the tested interval. The mean free distance for dislocation slip, interpreted here as the average size of the distribution of small subgrains, displays a variation with plastic strain which is in accordance with the different stages in the stress-strain curves. The rate of deformation hardening in the linear hardening range is accurately calculated using the variation of the small subgrain size with strain.

The corrosion of austenitic 304 stainless steel in biodiesel

Fuel distribution uses 304 stainless steel containers for the storage of biofuels, however there are few reports in the literature about the corrosive aspects this. steel in biodiesel. The objective of this research is to study the corrosive behavior of 304 austenitic stainless steel in the presence of biodiesel, unwashed and washed, with aqueous solutions of citric, oxalic, acetic and ascorbic acids 0,01 mol L(-1), and compare with results obtained for the copper (ASTM D130). The employedtechniques were: atomic absorption spectrometry (AAS) and optical microscopy (OM). The results of EA A showed a low rate of corrosion for the stainless steel, the alloys elements studied were Cr, Ni and Fe, the highest rate was observed for the chrome, 1.78 ppm / day in biodiesel with or without washing. The OM of the 304 steel, when compared with that of copper has a low corrosion rate in the 304 steel/biodiesel system. Not with standing, this demonstrates that not only the 304 steel, but also the copper corrodes in biodiesel

Evaluation of galling resistance for some selected combinations of tool steels/stainless steel sheet materials/lubricants using pin-on-disc testing

Stainless steels are well known to be prone to cold welding and material transfer in sliding contacts and therefore difficult to cold form unless certain precautions as discussed in this paper are taken. In the present study different combinations of tool steels/stainless steels/lubricants has been evaluated with respect to their galling resistance using pin-on-disc testing. The results show that a high galling resistance is favored by a high stainless steel sheet hardness and a blasted stainless steel sheet surface topography. The effect of type of lubricant was found to be more complex. For example, the chlorinated lubricants failed to prevent metal-to-metal contact on a brushed sheet surface but succeeded on a blasted sheet surface of the same stainless steel material. This is believed to be due to a protective tribofilm which is able to form on the blasted surface, but not on the brushed surface.

Aging behaviour of 25Cr-17Mn high nitrogen duplex stainless steel

The precipitation behaviour of a nickel free stainless steel containing 25% chromium, 17% manganese and 0.54% nitrogen, with duplex ferritic-austenitic microstructure, was studied using several complementary techniques of microstructural analysis after aging heat treatments between 600 and 1 000 degrees C for periods of lime between 15 and 6 000 min. During aging heat treatments, ferrite was decomposed into sigma phase and austenite by a eutectoid reaction, like in the Fe-Cr-Ni duplex stainless steel. Chromium nitride precipitation occurred in austenite, which had a high nitrogen supersaturation. Some peculiar aspects were observed in this austenite during its phase transformations. Chromium nitride precipitation occurred discontinuously in a lamellar morphology, such as pearlite in carbon steels. This kind of precipitation is not an ordinary observation in duplex stainless steels and the high levels of nitrogen in austenite can induce this type of precipitation, which has not been previously reported in duplex stainless steels. After chromium nitride precipitation in austenite, it was also observed sigma phase formation near the cells or colonies of discontinuously precipitated chromium nitride. Sigma phase formation was made possible by the depletion of nitrogen in those regions. Time-temperature-transformation (precipitation) diagrams were determined.

Corrosion behaviour of new duplex stainless steel reinforcements embedded in chloride contaminated concrete

The use of reinforcing stainless steels (SS) in concrete have proved to be one of the most effective methods to guarantee the passivity of reinforced concrete structures exposed to chloride contaminated environment. The present research studies the corrosion behaviour of a new duplex SS reinforcements with low nickel content (LND) (more economicaly compatible) is compared with the conventional austenitic AISI 304 SS and duplex AISI 2304 SS. Corrosion behaviour of ribbed SS reinforcements was studied in mortars with chloride content (0, 0.4, 2 and 4% Cl ⎯ ) using linear polarization resistance and potentiostatic pulses technique, Ecorr and Rp values were monitored over the exposure time. The obtained icorr data for the new duplex stainless steel LND no afforded passivity breakdown after one year exposure

Residual stress distribution in ferritic-austenitic steel joints made by laser welding

The present investigation addresse the influence of laser welding process-ing parameters used for joining dis-similar metals (ferritic to austenitic steel), on the induced residual stress field. Welding was performed on a Nd:YAG laser DY033 (3300 W) in a continuous wave (CW), keyhole mode. The base metals (BM) employed in this study are AISI 1010 carbon steel (CS) and AISI 304L austenitic stainless steel (SS). Pairs of dissimilar plates of 200 mm x 45 mm x 3 mm were butt joined by laser welding. Different sets of parameters were used to engineer the base metals apportionment at joint formation, namely distinct dilution rates. Residual strain scanning, carried out by neutron diffraction was used to assess the joints. Through-thickness residual stress maps were determined for the laser welded samples of dis-similar steels using high spatial reso-lution. As a result, an appropriate set of processing parameters, able to mi-nimize the local tensile residual stress associated to the welding process, was found.

Effect of copper addition on the fracture and fatigue crack growth behavior of solution heat-treated SUS 304H austenitic steel

Small additions of Cu to the SUS 304H, a high temperature austenitic stainless steel, enhance its high temperature strength and creep resistance. As Cu is known to cause embrittlement, the effect of Cu on room temperature mechanical properties that include fracture toughness and fatigue crack threshold of as-solutionized SUS 304H steel were investigated in this work. Experimental results show a linear reduction in yield and ultimate strengths with Cu addition of up to 5 wt.% while ductility drops markedly for 5 wt.% Cu alloy. However, the fracture toughness and the threshold stress intensity factor range for fatigue crack initiation were found to be nearly invariant with Cu addition. This is because the fracture in this alloy is controlled by the debonding from the matrix of chromium carbide precipitates, as evident from fractography. Cu, on the other hand, remains either in solution or as nano-precipitates and hence does not influence the fracture characteristics. It is concluded that small additions of Cu to 304H will not have adverse effects on its fracture and fatigue behavior. (C) 2010 Elsevier B.V. All rights reserved.

Influence of cast versus wrought microstructure on the processing map for hot working of stainless steel type AISI 304

Processing maps for hot working of as-cast and wrought stainless steels of type AISI 304 have been developed in the temperature range 600 to 1250°C and strain rate range 0.001 to 100 s−1. The domain of dynamic recrystallization (DRX) in as-cast material occurs at higher temperatures (1250°C) and lower strain rates (0.001 s−1) than in the wrought steel (1100°C and 0.01 s−1). The effect is explained in terms of enhanced nucleation rate of DRX due to the carbide, ferrite particles, stable oxides/nitrides and second-phase intermetallics in the as-cast microstructure. The DRX domain is wider in the wrought material although the peak efficiency is less (32%) than in the as-cast case (40%). The flow instability regime is not significantly affected by the initial microstructure