New reagents for the spectrophotometric determination of ranitidine hydrochloride

A new spectrophotometric method is proposed for the assay of ranitidine hydrochloride (RNH) in bulk drug and in its dosage forms using ceric ammonium sulphate (CAS) and two dyes, malachite (MAG) green and crystal violet (CV) as reagents. The method involves the addition of a known excess of ceric ammonium sulphate to ranitidine hydrochloride in acid medium, followed by the determination of unreacted CAS by reacting with a fixed amount of malachite green or crystal violet and measuring the absorbance at 615 or 582 nm respectively against the reagent blank. The Beer's law is obeyed in the concentration range of 0.4-8.0 µg/ ml of ranitidine hydrochloride (RNH) for RNH-MAG system and 0.2-1.6µg/ml of ranitidine hydrochloride for RNH-CV system. The molar Absorptivity, Sandell's sensitivity for each system were calculated. The method has been successfully applied to the determination of ranitidine hydrochloride in pure and dosage forms.

Effect of hydrodynamics on modelling, monitoring and control of crystallization

Crystallization is a purification method used to obtain crystalline product of a certain crystal size. It is one of the oldest industrial unit processes and commonly used in modern industry due to its good purification capability from rather impure solutions with reasonably low energy consumption. However, the process is extremely challenging to model and control because it involves inhomogeneous mixing and many simultaneous phenomena such as nucleation, crystal growth and agglomeration. All these phenomena are dependent on supersaturation, i.e. the difference between actual liquid phase concentration and solubility. Homogeneous mass and heat transfer in the crystallizer would greatly simplify modelling and control of crystallization processes, such conditions are, however, not the reality, especially in industrial scale processes. Consequently, the hydrodynamics of crystallizers, i.e. the combination of mixing, feed and product removal flows, and recycling of the suspension, needs to be thoroughly investigated. Understanding of hydrodynamics is important in crystallization, especially inlargerscale equipment where uniform flow conditions are difficult to attain. It is also important to understand different size scales of mixing; micro-, meso- and macromixing. Fast processes, like nucleation and chemical reactions, are typically highly dependent on micro- and mesomixing but macromixing, which equalizes the concentrations of all the species within the entire crystallizer, cannot be disregarded. This study investigates the influence of hydrodynamics on crystallization processes. Modelling of crystallizers with the mixed suspension mixed product removal (MSMPR) theory (ideal mixing), computational fluid dynamics (CFD), and a compartmental multiblock model is compared. The importance of proper verification of CFD and multiblock models is demonstrated. In addition, the influence of different hydrodynamic conditions on reactive crystallization process control is studied. Finally, the effect of extreme local supersaturation is studied using power ultrasound to initiate nucleation. The present work shows that mixing and chemical feeding conditions clearly affect induction time and cluster formation, nucleation, growth kinetics, and agglomeration. Consequently, the properties of crystalline end products, e.g. crystal size and crystal habit, can be influenced by management of mixing and feeding conditions. Impurities may have varying impacts on crystallization processes. As an example, manganese ions were shown to replace magnesium ions in the crystal lattice of magnesium sulphate heptahydrate, increasing the crystal growth rate significantly, whereas sodium ions showed no interaction at all. Modelling of continuous crystallization based on MSMPR theory showed that the model is feasible in a small laboratoryscale crystallizer, whereas in larger pilot- and industrial-scale crystallizers hydrodynamic effects should be taken into account. For that reason, CFD and multiblock modelling are shown to be effective tools for modelling crystallization with inhomogeneous mixing. The present work shows also that selection of the measurement point, or points in the case of multiprobe systems, is crucial when process analytical technology (PAT) is used to control larger scale crystallization. The thesis concludes by describing how control of local supersaturation by highly localized ultrasound was successfully applied to induce nucleation and to control polymorphism in reactive crystallization of L-glutamic acid.

Sweet grape mini tomato grown in culture substrates and effluent with nutrient complementation

The objective of this study was to evaluate production of Sweet Grape mini tomato (Lycopersicum esculentum Mill.) using culture substrates and nutrient solution sewage effluent, applied by drip irrigation (fertigation). The experiment was conducted at the University of Goiás State (UEG-UnUCET), from June to November 2011 in Anápolis-GO, Brazil. The experimental design was a 2 x 3 factorial arrangement in a randomized complete block design with four repetitions. The plots were made by combining two nutrient solutions, effluent supplemented with mineral fertilizers (EcS); conventional nutrient solution (SnC); in addition three cultivation substrates: 60% of fine sand washed + 40% substrate composed by 20% coconut fiber plus 80% pine bark (S1); 20% coconut fiber and 80% pine bark (S2) and natural coconut fiber (S3). Sewage effluent were determined nitrate, calcium, potassium, manganese, total phosphate, total iron, magnesium, chloride, sulphate, boron, zinc and molybdenum. We evaluated average mass and average number of fruits per bunch, total fruit and total yield per plant. Statistical difference absence among tested solutions indicates sewage effluent can be used as an alternative source of nutrients in growing mini tomatoes in hydroponics.

Steroidien selektiivinen erottaminen sähköavusteisesti mikroemulsioita käyttäen

Mikroemulsiosähkökineettinen kromatografia on sähköavusteinen erotusmenetelmä. Yhdisteiden erottuminen tapahtuu mikroemulsiopisaroiden vaikutuksesta, kun nanometrien kokoiset öljypisarat ovat dispergoituneena veteen valmistettuun puskuriliuokseen. Yleensä mikroemulsiot valmistetaan raakaöljynkin sisältämistä hiilivedyistä, joita ovat esimerkiksi oktaani ja heptaani. Työn kokeellisessa osassa perehdyttiin seitsemän hydrofobisen ja varauksettoman steroidihormonin erottamiseen mikroemulsioliuoksessa kapillaarielektroforeesitekniikalla. Työssä valmistettiin öljyistä koostuvia mikroemulsioita, joista osan koostumus valittiin kirjallisuuden perusteella. Työssä kokeiltiin myös uusia mikroemulsiokoostumuksia, joissa käytettiin luonnosta peräisin olevia öljyjä: rypsi-, oliivi-, pellavansiemen- ja saksanpähkinäöljyä. Seitsemästä steroidihormonista viisi yhdistettä saatiin erottumaan optimoiduilla menetelmillä. Steroidien erotus perustuu niiden oktanoli-vesi jakautumiskertoimien avulla saatavaan migraatiojärjestykseen. Mikroemulsiossa, jossa käytettiin 1-oktanolia, steroidihormonit erottuivat nopeammin, kuin saksanpähkinäöljyä käytettäessä. Lyhyimmät migraatioajat saatiin mikroemulsiolla, jossa öljyfaasina käytettiin 1-heksanolia ja viidentenä yhdisteenä asetonitriiliä. Selektiivisimmillään menetelmä on, kun erotus tapahtuu liuoksessa, joka koostuu etyyliasetaatista, natriumdodekyylisulfaatista, butanolista, asetonitriilistä ja natriumtetraboraatista. Toteamisrajat tutkituille steroidihormoneille olivat 0,20–0,43 mg/L mikroemulsioissa.

Pasvik Water Quality Report Environmental Monitoring Programme in the Norwegian, Finnish and Russian Border Area

The Pasvik monitoring programme was created in 2006 as a result of the trilateral cooperation, and with the intention of following changes in the environment under variable pollution levels. Water quality is one of the basic elements of the Programme when assessing the effects of the emissions from the Pechenganikel mining and metallurgical industry (Kola GMK). The Metallurgic Production Renovation Programme was implemented by OJSC Kola GMK to reduce emissions of sulphur and heavy metal concentrated dust. However, the expectations for the reduction in emissions from the smelter in the settlement Nikel were not realized. Nevertheless, Kola GMK has found that the modernization programme’s measures do not provide the planned reductions of sulfur dioxide emissions. In this report, temporal trends in water chemistry during 2000–2009 are examined on the basis of the data gathered from Lake Inari, River Pasvik and directly connected lakes, as well as from 26 small lakes in three areas: Pechenganikel (Russia), Jarfjord (Norway) and Vätsäri (Finland). The lower parts of the Pasvik watercourse are impacted by both atmospheric pollution and direct wastewater discharge from the Pechenganikel smelter and the settlement of Nikel. The upper section of the watercourse, and the small lakes and streams which are not directly linked to the Pasvik watercourse, only receive atmospheric pollution. The data obtained confirms the ongoing pollution of the river and water system. Copper (Cu), nickel (Ni) and sulphates are the main pollution components. The highest levels were observed close to the smelters. The most polluted water source of the basin is the River Kolosjoki, as it directly receives the sewage discharge from the smelters and the stream connecting the Lakes Salmijarvi and Kuetsjarvi. The concentrations of metals and sulphates in the River Pasvik are higher downstream from the Kuetsjarvi Lake. There has been no fall in the concentrations of pollutants in Pasvik watercourse over the last 10 years. Ongoing recovery from acidification has been evident in the small lakes of the Jarfjord and Vätsäri areas during the 2000s. The buffering capacity of these lakes has improved and the pH has increased. The reason for this recovery is that sulphate deposition has decreased, which is also evident in the water quality. However, concentrations of some metals, especially Ni and Cu, have risen during the 2000s. Ni concentrations have increased in all three areas, and Cu concentrations in the Pechenganickel and Jarfjord areas, which are located closer to the smelters. Emission levels of Ni and Cu did not fall during 2000s. In fact, the emission levels of Ni compounds even increased compared to the 1990s.

Serum protein concentrations, including acute phase proteins, in calves experimentally infected with Salmonella Dublin

The aim of this study was to evaluate serum protein concentrations in calves experimentally inoculated with Salmonella Dublin. Twelve healthy 10 to 15-day-old Holstein calves were randomly allotted into two groups, control and infected with 10(8) CFU of Salmonella Dublin orally. The calves were subjected to physical evaluation and blood samples were collected shortly before administration of the bacteria and also 24, 48, 72, 96, 120 and 168 hours post-infection. The concentration of serum proteins was determined through sodium dodecyl sulphate-polyacrylamide gel electrophoresis (SDS-PAGE). Thirty serum proteins ranging from molecular weight of 24,000 Da to molecular weight of 236,000 Da were detected. Serum concentrations of ceruloplasmin (125,000 Da), haptoglobin (45,000 Da), acid glycoprotein (40,000 Da) and a 34,000 Da protein were significantly increased in the experimentally infected calves, when compared with their concentrations in the control animals. Therefore, this study showed that S. Dublin infection could lead to the increase of certain serum proteins in calves.

Electrochemical Treatment of Wastewaters

Electrocoagulation is a process in which wastewater is treated under electrical current. Coagulant is formed during the process through the metal anode dissolution to respective ions which react with hydroxyl ions released in cathode. These metal hydroxides form complexes with pollutant ions. Pollutants are removed among metal hydroxide precipitates. This study was concentrated on describing chemistry and device structures in which electrochemical treatment operations are based on. Studied pollutants were nitrogen compounds, sulphate, trivalent and pentavalent arsenic, heavy metals, phosphate, fluoride, chloride, and bromide. In experimental part, removal of ammonium, nitrate, and sulphate during electrochemical treatment was studied separately. Main objective of this study was to find suitable metal plate material for ammonium, nitrate, and sulphate removal, respectively. Also other parameters such as pH of solution, concentration of pollutant and sodium chloride, and current density were optimized. According to this study the most suitable material for ammonium and sulphate removal by electrochemical treatment was stainless steel. Respectively, iron was the optimum material for nitrate removal. Rise in the pH of solution at the final stage of electrochemical treatment of ammonium, nitrate, and sulphate was detected. Conductivities of solutions decreased during ammonium removal in electrochemical processes. When nitrate and sulphate were removed electrochemically conductivities of solutions increased. Concentrations of residual metals in electrochemically treated solutions were not significant. Based on this study electrochemical treatment processes are recommended to be used in treatment of industrial wastewaters. Treatment conditions should be optimized for each wastewater matrix.

Crystallization of selected anions and cations from mine waters

The aim of this Master’s thesis was to review some methods that are already being utilized in a field of mine water purification and to find and study possible new methods and chemicals for mine water purification by precipitation. The target was also to list the optimal process conditions for these precipitating chemicals. Separation methods were reviewed for several anions and cations, but being a real topical issue, sulphate removal was selected to be in the main focus. Sulphate salts e.g. Na2SO4 are relatively soluble in water, which makes the separation processes difficult. Eutectic freeze crystallization was studied more closely in laboratory tests for sodium sulphate removal. Gravimetric solubility tests were made for three cases of mixed electrolyte solutions: Na2SO4 – NaOH, BaSO4 – NaOH and Na3PO4 – NaOH. The aim of these experiments was to study the effect of NaOH addition on solubility of the studied salt. These phenomena were however noticed to be difficult to see in the used laboratory tests. Thus mathematical modelling was utilized to contribute the laboratory experiments and to bring additional information of the influence of NaOH presence on solubility of selected electrolytes, Na2SO4 and Na3PO4. The results from mathematical modelling of activity coefficients suggest Na2SO4 and Na3PO4 to be precipitated rather with presence and with higher concentrations of NaOH, since the raise of NaOH concentration decreases the solubility of these electrolytes in water.

Optimizing activity of herbicides at reduced rate on Emex spinosa campd. with adjuvants

In pot experiments, two adjuvants were evaluated for their efficacy in enhancing activity of five herbicides applied at reduced rates (75% of the recommended rates) on Emex spinosa at the cotyledon-leaf and at the two- to four- leaf stage. Herbicides (at recommended rates) including fluroxypyr+MCPA at 450 g a.i. ha-1, carfentrazone-ethyl at 20 g a.i. ha-1, bromoxynil+MCPA at 450 g a.i. ha-1, thifensulfuron-methyl at 75 g a.i. ha-1 and tribenuronmethyl at 75 g a.i. ha-1 alone and tank mixed at reduced rates with adjuvants, namely, alkyl ether sulphate sodium salt at 625 mL ha-1 or fatty alcohol ethoxylate at 375 mL ha-1. Addition of the adjuvants to reduced rates of fluroxypyr+MCPA and carfentrazone-ethyl, increased their efficacy with 100% mortality and biomass reduction of E. spinosa at the cotyledon- leaf stage and at the two- to four- leaf stage which was similar to their recommended rates without the adjuvants except for carfentrazone-ethyl at a reduced rate without adjuvants at the two- to four- leaf stage. Bromoxynil+MCPA at reduced rates with alkyl ether sulphate sodium salt also gave 100% control of E. spinosa over weedy check at the two- to four- leaf stage. Both the adjuvants generally increased the efficacy of tribenuron-methyl at reduced rates when sprayed at both leaf stages. These findings suggest that the use of adjuvants may increase the efficacy of the above mentioned herbicides against E. spinosa and it may be incorporated in an integrated weed management program.

Multiple forms of cotyledonary b-galactosidases from Vigna unguiculata quiescent seeds

Cotyledonary b-galactosidases were isolated and partially purified from Pitiúba cowpea (Vigna unguiculata (L.) Walp.) quiescent seeds. The purification steps consisted of precipitation of the crude extract with ammonium sulphate in the range of 20-60% saturation, acid precipitation, DEAE-Sephadex ion-exchange chromatography and Lactosyl-Sepharose affinity chromatography. This purification process gave rise to three b-galactosidases-rich fractions: b-gal I, b-gal II and b-gal III, which were purified about 5, 509, and 62 fold, respectively. They reached maximal enzyme activity at different pH ranges: 3.5-4.5 for b-gal I, 3.0-3.5 for b-gal II, and 3.0-4.0 for b-gal III. Their maximal activities were reached when the temperature of the assay medium was 60° C, and preincubation of the enzymes at different temperatures has shown that they were heat-stable up to 50° C. There were no significant differences among the partially purified enzymes as far as their response to the different effectors tested, except for Mn2+ and EDTA, which affected differently b-gal I, b-gal II, and b-gal III. They were slightly affected by Mg2+, Ca2+, Zn2+, Co2+, tartarate, molybdate, glucose, and lactose, strongly inhibited by Cu2+ and galactose, and inactivated by Hg2+. These chemical and physical properties are similar to the ones found for other plant b-galactosidases. Although through this process of purification three isoforms of this enzyme were obtained, isoelectric focusing in polyacrylamide slab gel of these enzyme-proteins suggest that cotyledons of Pitiúba cowpea quiescent seeds possess four isoforms of b-galactosidases.

Ontogeny and structure of the pericarp and the seed coat of Miconia albicans (Sw.) Triana (Melastomataceae) from " cerrado" , Brazil

Miconia albicans fruit and seed coat ontogeny were described under light microscope. The samples were fixed in formalin-aceto-alcohol (FAA), neutral-buffered formaldehyde solution (NBF) and formalin-ferrous sulphate (FFS) solutions, embedded in plastic resin, sectioned at 10 µm and stained with Toluidine Blue. Specific dyes and/or reagents were used for the microchemical tests. The ovary is semi-inferior and the indehiscent, fleshy globose berries are originated mainly from the development of the inferior portion of the ovary. The immature pericarp is mainly parenchymatous with some sclereids, druse crystal and phenolic-like compounds idioblasts widespread in the mesocarp. In the mature pericarp, the endocarp cells are often collapsed, the mesocarp is thick with cells more or less turgid, and the sclereids, the druses and the phenolic-like compound idioblasts are almost absent. The ovules are anatropous, bitegmic and crassinucellate, and the zig-zag micropyle is formed by both the exostome and the endostome. The mature seed is pyramidal-elongated in shape, exalbuminous and testal. The raphal part occupies about 40% of the seed coat total length and had the mechanical layer derived from its inner layer. The antiraphal side is non-multiplicative and the exotesta, mesotesta and endotesta are differentiated into a sclerotic layer, with the exotesta being the mechanical one. The tegmen is absent.

The role of metal ions in selective and sustainable processes

Sustainability and recycling are core values in today’s industrial operations. New materials, products and processes need to be designed in such a way as to consume fewer of the diminishing resources we have available and to put as little strain on the environment as possible. An integral part of this is cleaning and recycling. New processes are to be designed to improve the efficiency in this aspect. Wastewater, including municipal wastewaters, is treated in several steps including chemical and mechanical cleaning of waters. Well-cleaned water can be recycled and reused. Clean water for everyone is one of the greatest challenges we are facing today. Ferric sulphate, made by oxidation from ferrous sulphate, is used in water purification. The oxidation of ferrous sulphate, FeSO4, to ferric sulphate in acidic aqueous solutions of H2SO4 over finely dispersed active carbon particles was studied in a vigorously stirred batch reactor. Molecular oxygen was used as the oxidation agent and several catalysts were screened: active carbon, active carbon impregnated with Pt, Rh, Pd and Ru. Both active carbon and noble metal-active carbon catalysts enhanced the oxidation rate considerably. The order of the noble metals according to the effect was: Pt >> Rh > Pd, Ru. By the use of catalysts, the production capacities of existing oxidation units can be considerably increased. Good coagulants have a high charge on a long polymer chain effectively capturing dirty particles of the opposite charge. Analysis of the reaction product indicated that it is possible to obtain polymeric iron-based products with good coagulation properties. Systematic kinetic experiments were carried out at the temperature and pressure ranges of 60B100°C and 4B10 bar, respectively. The results revealed that both non-catalytic and catalytic oxidation of Fe2+ to Fe3+ take place simultaneously. The experimental data were fitted to rate equations, which were based on a plausible reaction mechanism: adsorption of dissolved oxygen on active carbon, electron transfer from Fe2+ ions to adsorbed oxygen and formation of surface hydroxyls. A comparison of the Fe2+ concentrations predicted by the kinetic model with the experimentally observed concentrations indicated that the mechanistic rate equations were able to describe the intrinsic oxidation kinetics of Fe2+ over active carbon and active carbon-noble metal catalysts. Engineering aspects were closely considered and effort was directed to utilizing existing equipment in the production of the new coagulant. Ferrous sulphate can be catalytically oxidized to produce a novel long-chained polymeric iron-based flocculent in an easy and affordable way in existing facilities. The results can be used for modelling the reactors and for scale-up. Ferric iron (Fe3+) was successfully applied for the dissolution of sphalerite. Sphalerite contains indium, gallium and germanium, among others, and the application can promote their recovery. The understanding of the reduction process of ferric to ferrous iron can be used to develop further the understanding of the dissolution mechanisms and oxidation of ferrous sulphate. Indium, gallium and germanium face an ever-increasing demand in the electronics industry, among others. The supply is, however, very limited. The fact that most part of the material is obtained through secondary production means that real production quota depends on the primary material production. This also sets the pricing. The primary production material is in most cases zinc and aluminium. Recycling of scrap material and the utilization of industrial waste, containing indium, gallium and geranium, is a necessity without real options. As a part of this study plausible methods for the recovery of indium, gallium and germanium have been studied. The results were encouraging and provided information about the precipitation of these valuables from highly acidic solutions. Indium and gallium were separated from acidic sulphuric acid solutions by precipitation with basic sulphates such as alunite or they were precipitated as basic sulphates of their own as galliunite and indiunite. Germanium may precipitate as a basic sulphate of a mixed composition. The precipitation is rapid and the selectivity is good. When the solutions contain both indium and gallium then the results show that gallium should be separated before indium to achieve a better selectivity. Germanium was separated from highly acidic sulphuric acid solutions containing other metals as well by precipitating with tannic acid. This is a highly selective method. According to the study other commonly found metals in the solution do not affect germanium precipitation. The reduction of ferric iron to ferrous, the precipitation of indium, gallium and germanium, and the dissolution of the raw materials are strongly depending on temperature and pH. The temperature and pH effect were studied and which contributed to the understanding and design of the different process steps. Increased temperature and reduced pH improve the reduction rate. Finally, the gained understanding in the studied areas can be employed to develop better industrial processes not only on a large scale but also increasingly on a smaller scale. The small amounts of indium, gallium and germanium may favour smaller and more locally bound recovery.

Roles of keratins in intestinal health and disease

Intermediate filament keratins (K) play a pivotal role in protein targeting and epithelialcytoprotection from stress as evidenced by keratin mutations predisposing to human liver and skin diseases and possibly inflammatory bowel disease (IBD). The K8-null (K8-/-) mice exhibit colonic phenotype similar to IBD and marked spontaneous colitis, epithelial hyperproliferation, decreased apoptosis, mistargeting of proteins leading to defective ion transport and diarrhea. The K8-heterozygote (K8+/-) mouse colon appears normal but displays a defective sodium (Na+) and chloride (Cl-) transport similar to, but milder than K8-/-. Characterization of K8+/- colon revealed ~50% less keratins (K7, K8, K19, K20) compared to K8 wild type (K8+/+). A similar ~50% decrease was seen in K8+/- mRNA levels as compared to K8+/+, while the mRNA levels for the other keratins were unaltered. K8+/- keratins were arranged in a normal colonic crypt expression pattern, except K7 which was expressed at the top of crypts in contrast to K8+/+. The K8+/- colon showed mild hyperplasia but no signs of inflammation and no resistance to apoptosis. Experimental colitis induced by using different concentrations of dextran sulphate sodium (DSS) showed that K8+/- mice are slightly more sensitive to induced colitis and showed a delayed recovery compared to K8+/+. Hence, the K8+/- mouse with less keratins and without inflammation, provided a novel model to study direct molecular mechanisms of keratins in intestinal homeostasis and ion transport. Different candidate ion transporters for a possible role in altered ion transport seen in the K8-/- and K8+/- mouse colon were evaluated. Besides normal levels of CFTR, PAT-1 and NHE-3, DRA mRNA levels were decreased 3-4-fold and DRA protein nearly entirely lost in K8-/- caecum, distal and proximal colon compared to K8+/+. In K8+/- mice, DRA mRNA levels were unaltered while decreased DRA protein level and patchy distribution was detected particularly in the proximal colon and as compared to K8+/+. DRA was similarly decreased when K8 was knocked-down in Caco-2 cells, confirming that K8 levels modulate DRA levels in an inflammation-independent manner. The dramatic loss of DRA in colon and caecum of K8-/- mice was responsible for the chloride transport defect. The milder ion transport in K8+/- colon might be related to DRA suggesting a role for K8 in regulation of DRA expression and targeting. The current study demonstrates the importance of keratins in stress protection and cell signaling. Furthermore, we have also successfully developed a novel, simple, fast, cost effective, non-invasive in vivo imaging method for the early diagnosis of murine colitis with specificity for both genetic and experimental colitis. The said modality provides continuous measurements of reactive oxygen and nitrogen species (RONS) and minimizes the use of an increased number of experimental animals by using a luminal derivative chemiluminescent probe, L-012 which provides a cost-effective tool to study the level and longitudinal progression of colitis.

Production of magnesium carbonates from serpentinites for CO2 mineral sequestration : optimisation towards industrial application

Global warming is one of the most alarming problems of this century. Initial scepticism concerning its validity is currently dwarfed by the intensification of extreme weather events whilst the gradual arising level of anthropogenic CO2 is pointed out as its main driver. Most of the greenhouse gas (GHG) emissions come from large point sources (heat and power production and industrial processes) and the continued use of fossil fuels requires quick and effective measures to meet the world’s energy demand whilst (at least) stabilizing CO2 atmospheric levels. The framework known as Carbon Capture and Storage (CCS) – or Carbon Capture Utilization and Storage (CCUS) – comprises a portfolio of technologies applicable to large‐scale GHG sources for preventing CO2 from entering the atmosphere. Amongst them, CO2 capture and mineralisation (CCM) presents the highest potential for CO2 sequestration as the predicted carbon storage capacity (as mineral carbonates) far exceeds the estimated levels of the worldwide identified fossil fuel reserves. The work presented in this thesis aims at taking a step forward to the deployment of an energy/cost effective process for simultaneous capture and storage of CO2 in the form of thermodynamically stable and environmentally friendly solid carbonates. R&D work on the process considered here began in 2007 at Åbo Akademi University in Finland. It involves the processing of magnesium silicate minerals with recyclable ammonium salts for extraction of magnesium at ambient pressure and 400‐440⁰C, followed by aqueous precipitation of magnesium in the form of hydroxide, Mg(OH)2, and finally Mg(OH)2 carbonation in a pressurised fluidized bed reactor at ~510⁰C and ~20 bar PCO2 to produce high purity MgCO3. Rock material taken from the Hitura nickel mine, Finland, and serpentinite collected from Bragança, Portugal, were tested for magnesium extraction with both ammonium sulphate and bisulphate (AS and ABS) for determination of optimal operation parameters, primarily: reaction time, reactor type and presence of moisture. Typical efficiencies range from 50 to 80% of magnesium extraction at 350‐450⁰C. In general ABS performs better than AS showing comparable efficiencies at lower temperature and reaction times. The best experimental results so far obtained include 80% magnesium extraction with ABS at 450⁰C in a laboratory scale rotary kiln and 70% Mg(OH)2 carbonation in the PFB at 500⁰C, 20 bar CO2 pressure for 15 minutes. The extraction reaction with ammonium salts is not at all selective towards magnesium. Other elements like iron, nickel, chromium, copper, etc., are also co‐extracted. Their separation, recovery and valorisation are addressed as well and found to be of great importance. The assessment of the exergetic performance of the process was carried out using Aspen Plus® software and pinch analysis technology. The choice of fluxing agent and its recovery method have a decisive sway in the performance of the process: AS is recovered by crystallisation and in general the whole process requires more exergy (2.48–5.09 GJ/tCO2sequestered) than ABS (2.48–4.47 GJ/tCO2sequestered) when ABS is recovered by thermal decomposition. However, the corrosive nature of molten ABS and operational problems inherent to thermal regeneration of ABS prohibit this route. Regeneration of ABS through addition of H2SO4 to AS (followed by crystallisation) results in an overall negative exergy balance (mainly at the expense of low grade heat) but will flood the system with sulphates. Although the ÅA route is still energy intensive, its performance is comparable to conventional CO2 capture methods using alkanolamine solvents. An energy‐neutral process is dependent on the availability and quality of nearby waste heat and economic viability might be achieved with: magnesium extraction and carbonation levels ≥ 90%, the processing of CO2‐containing flue gases (eliminating the expensive capture step) and production of marketable products.

Mineraalien rikastusprosessin vesijalanjälki

Mineraalien rikastamiseen käytetään useita fysikaalisia ja kemiallisia menetelmiä. Prosessi sisältää malmin hienonnuksen, rikastuksen ja lopuksi vedenpoistamisen rikastelietteestä. Malmin rikastamiseen käytetään muun muassa vaahdotusta, liuotusta, magneettista rikastusta ja tiheyseroihin perustuvia rikastusmenetelmiä. Rikastuslietteestä voidaan poistaa vettä sakeuttamalla ja suodattamalla. Rikastusprosessin ympäristövaikutuksia voidaan arvioida laskemalla tuotteen vesijalanjälki, joka kertoo valmistamiseen kulutetun veden määrän. Tässä kirjallisuustyössä esiteltiin mineraalien käsittelymenetelmiä sekä prosessijätevesien puhdistusmenetelmiä. Kirjallisuuslähteiden pohjalta selvitettiin Pyhäsalmen kaivoksella valmistetun kuparianodin vesijalanjälki sekä esitettiin menetelmiä, joilla prosessiin tarvittavan raakaveden kulutusta voitaisiin vähentää. Pyhäsalmella kuparirikasteesta valmistetun kuparianodin vesijalanjälki on 240 litraa H2O ekvivalenttia tuotettua tonnia kohden. Pyhäsalmen prosessin raakaveden kulutusta voidaan vähentää lisäämällä sisäistä vedenkierrätystä. Kalsiumsulfaatin saostuminen putkiin ja pumppuihin on ilmentynyt ongelmaksi vedenkierrätyksen lisäämisessä. Kalsiumsulfaattia voidaan erottaa vedestä membraaneihin, ioninvaihtoon ja sähkökemiaan perustuvilla tekniikoilla. Vaihtoehdossa, jossa johdetaan kaikista kolmesta vaahdotuksesta saatavat rikastuslietteen ja rikastushiekan sakeutuksien ylitteet sekä suodatuksien suodosvedet samaan vedenkäsittelyyn voidaan kattaa arviolta noin 65 % koko veden tarpeesta. Raakavettä säästetään vuodessa 3,4 Mm^3 ja samalla rikastushiekka-altaiden tarvittava koko pienenee, joka vähentää ympäristöriskejä.