Online titrimetric and off-gas analysis for examining nitrification processes in wastewater treatment

The two steps of nitrification, namely the oxidation of ammonia to nitrite and nitrite to nitrate, often need to be considered separately in process studies. For a detailed examination, it is desirable to monitor the two-step sequence using online measurements. In this paper, the use of online titrimetric and off-gas analysis (TOGA) methods for the examination of the process is presented. Using the known reaction stoichiometry, combination of the measured signals (rates of hydrogen ion production, oxygen uptake and carbon dioxide transfer) allows the determination of the three key process rates, namely the ammonia consumption rate, the nitrite accumulation rate and the nitrate production rate. Individual reaction rates determined with the TOGA sensor under a number of operation conditions are presented. The rates calculated directly from the measured signals are compared with those obtained from offline liquid sample analysis. Statistical analysis confirms that the results from the two approaches match well. This result could not have been guaranteed using alternative online methods. As a case study, the influences of pH and dissolved oxygen (DO) on nitrite accumulation are tested using the proposed method. It is shown that nitrite accumulation decreased with increasing DO and pH. Possible reasons for these observations are discussed. (C) 2003 Elsevier Science Ltd. All rights reserved.

Mid- to Late-Holocene estuarine infilling processes studied by radiocarbon dates, high resolution seismic and biofacies at Vitoria Bay, Espirito Santo, Southeastern Brazil

A Baía de Vitória é um estuário com 20 km de comprimento, morfologicamente estreito, com um regime de micromaré e, como outros estuários modernos, formado durante a última transgressão pós-glacial. A morfologia de fundo do estrato estuarino é caracterizada por um canal natural principal limitado por planícies de maré com manguezais desenvolvidos. Datações de radiocarbono originais foram obtidas para a área. Cinco idades de radiocarbono estendendo-se de 1.010 a 7.240 anos AP foram obtidas através de dois testemunhos de sedimento, representando uma sequência estratigráfica de 5 m de espessura. Os resultados indicam que até aproximadamente 4.000 anos cal. AP, as condições ambientais da Baía de Vitória eram ainda de uma baía aberta, com uma conexão livre e aberta com águas marinhas. Durante os últimos 4.000 anos a baía experimentou uma fase de regressão importante, tornando-se mais restrita em termos de circulação da água do mar e provavelmente aumentando a energia de marés. Três superfícies estratigráficas principais foram reconhecidas, limitando fácies transgressiva, transgressiva/nível de mar alto e regressiva. A morfologia do canal atual representa um diastema de maré, mostrando fácies regressivas truncadas e erodidas. Biofácies de foraminíferos, passando de ambiente marinho para ambiente salobro e de manguezais em planície de maré confirmam a interpretação sismoestratigráfica. A ausência de biofácies de mangue em um dos dois testemunhos é tambémuma indicação de ravinamento de maré atual.

Efeito da adição de óleo essencial de pimenta rosa (Schinus terebinthifolius Raddi) microencapsulado em queijo minas frescal

A pimenta rosa é o fruto da aroeira (Schinus terebinthifolius Raddi), uma planta nativa do Brasil. A extração e caracterização do seu óleo essencial viabiliza a sua utilização industrial. Este trabalho teve como objetivo avaliar o efeito da adição de óleo essencial de pimenta rosa em queijo Minas Frescal . Foram identificados 95,36% dos constituintes do óleo essencial, sendo o δ-careno-3 o componente majoritário. O óleo essencial de pimenta rosa apresentou características antioxidante (2,53 ± 0,28 μmols de trolox por mL de óleo) e antimicrobiana para o desenvolvimento de Staphylococcus aureus. Foi observado, no teste de difusão em ágar, a formação do halo de inibição de 1,35 ± 0,32 cm, e na análise de concentração inibitória mínima, o valor de 3,13%. O óleo essencial é sensível à degradação no meio em que se encontra, portanto necessita de processos tecnológicos para assegurar sua ação. Para proteger o óleo essencial foi realizada a microencapsulação por meio da secagem por spray dryer. O óleo foi microencapsulado utilizando três formulações com diferentes concentrações de goma arábica, maltodextrina e amido modificado como papel de parede. As microcápsulas obtidas foram analisadas quanto às suas características físico-químicas e morfológicas e foi selecionada uma formulação para posterior adição ao queijo Minas Frescal. A formulação com 5% de amido modificado, 10% de maltodextrina e 5% de goma arábica foi selecionada. Para definição da concentração de óleo essencial que foi utilzada no queijo, foi realizado teste sensorial de ordenação-preferência, visto que a concentração inibitória mínima (3,13%) era muito alta para ser utilizada nos queijos. A formulação com 0,01% de óleo essencial foi a preferida e utilizada para fabricação dos queijos. Foram elaborados e caracterizados os queijos controle (CO) e o queijo com adição das microcápsulas de óleo essencial de pimenta rosa (OEPR). Em relação às características físico-químicas, os queijos CO e OEPR só apresentaram diferença significativa em relação à umidade (P= 0,0021; α=0,05). O queijo OEPR teve boa aceitação sensorial com média de aceitação global de 7,6 ± 0,97, não apresentando diferença significativa, ao nível de 95% de confiança, do queijo controle (7,6 ± 1,18). Para avaliar a capacidade do óleo essencial de pimenta rosa microencapsulado em inibir o desenvolvimento de S. aureus, foram inoculadas nos queijos CO e OEPR concentrações iniciais de 106 UFG.g. Os queijos foram armazenados em BOD à temperatura de 4 ± 1 °C até realização das análises, que ocorreram nos tempos: 0, 3, 6, 9, 12, 15 e 30 dias. Houve redução de 1,53 ciclos Log no queijo adicionado de óleo essencial de pimenta rosa. De acordo com os resultados obtidos, conclui-se que o óleo essencial de pimenta rosa é uma alternativa viável de utilização em queijo Minas Frescal , devido ao seu potencial antioxidante, antimicrobiano e à sua aceitação sensorial.

Cobertura permanente de solo com leguminosas herbáceas perenes no cultivo de bananeiras no médio Vale do Jequitinhonha

A região da Caatinga é caracterizada pelas altas temperaturas durante o ano e má distribuição das chuvas. Em virtude desses fatores de clima regional, tem-se a necessidade de adoção por práticas que elevem à eficiência e sustentabilidade agrícola local. Assim, objetivou-se avaliar a aptidão de leguminosas herbáceas perenes como cobertura permanente de solo no cultivo de bananeira. Foram conduzidos três experimentos, para avaliação das leguminosas, utilizou-se um delineamento experimental em blocos casualizados, com quatro repetições, em esquema de parcelas subdivididas no espaço e para algumas variáveis, sub-subdividida no tempo, sendo: Fator “A” os dois diferentes ambientes de plantio: municípios de Itaobim/MG e Virgem da Lapa/MG; Fator “B”, nas subparcelas, dois manejos de cobertura do solo e para algumas variáveis, três manejos, constituídos pelas leguminosas: cudzu tropical (Pueraria phaseoloides) calopogônio (Calopogonium mucunoides) e solo descoberto (solo capinado); Fator “C” épocas de coleta de dados. Para avaliação das bananeiras, foram dois experimentos em blocos casualizados, com quatro repetições, em esquema de parcelas sudivididas no espaço, sendo: nas parcelas, fator “A” constituído por três manejos de cobertura do solo, pelas leguminosas: cudzu tropical e o calopogônio, e solo descoberto (solo capinado); fator “B”, nas subparcelas, plantas de bananeiras em três idades morfofisiológicas (diferentes ciclos e tamanhos); Para algumas variáveis que foram submetidas a coletas periódicas, utilizou-se o esquema de parcelas subsubdivididas no tempo, acrescentando-se o fator “C”, datas das coletas nas sub-subparcelas, tendo como referência os dias após semeadura (DAS) das leguminosas. Foram avaliadas as seguintes variáveis: taxa de cobertura do solo; potencial de deposição de folhas e a ciclagem de nutrientes; capacidade de inibição da vegetação espontânea; conservação da temperatura e promoção da retenção de umidade do solo. Também foi avaliado o crescimento vegetativo e produtividade das bananeiras. Como resultados principais, notou-se que as leguminosas proporcionaram eficiente cobertura do solo, o calopogônio apresentou o maior acúmulo de N, P, K, e Ca, via deposição de material senescente, tal como maior inibição das plantas espontâneas nos pomares de bananeiras. Essa cobertura também promoveu uma eficiente redução da temperatura do solo, possibilitando menor variação térmica nas camadas de maior concentração radicular da bananeira, e consequentemente, obtendo maior acúmulo de umidade no solo. As bananeiras cultivadas sobre coberturas vivas de solo apresentaram aumento gradativo no crescimento e peso de cacho. Os resultados reforçam o potencial uso dessas espécies na fruticultura, principalmente em regiões de severas restrições hídricas, como forma de adubação e otimização de diversos processos biológicos em seu ambiente de cultivo.

Improving the environmental performance of bedding products by using life cycle assessment at the design stage

Improvement of the environmental performance of processes and products is a common objective in industry, and has been receiving increased attention in recent years. The main objective of this work is to evaluate the potential environmental impact of two bedding products, a polyurethane foam mattress (PFM) and a pocket spring mattress (PSM). These two types are the most common mattresses used in Europe. A Life Cycle Assessment (LCA) shows that the PFM has a higher environmental impact than the PSM. For both products the main cause of environmental impact is the manufacturing process, respectively the polyurethane foam block moulding process for the PFM, and the pocket spring nucleus process for the PSM. A scenario analysis shows the possibility of reducing the environmental impact of the products’ life cycle using an alternative End-of-Life scenario, resorting to incineration rather than landfill. Two strategies were also studied in order to reduce the environmental impact of the PFM: (1) reutilization of foam that was sent to the waste system management, and (2) a 20% weight reduction of the polyurethane foam. The second strategy has proven to be the most effective.

The effect of leaf area reduction on corn plants during the reproduction phase

Reduction in leaf area in corn plants during reproduction changes physiological metabolism and consequently the accumulation of dry matter in grains. The aim of this work was to study changes in agronomic characteristics caused by defoliation in corn during the reproduction phase. The experiment was carried out in Uberlândia, Minas Gerais state, in the agricultural year 2007/2008. The experiment was arranged in a randomized block design, consisting of seven treatments: control without defoliation, removal of two apical leaves, removal of four apical leaves, removal of all leaves above spike, removal of four intermediate leaves, removal of all leaves below spike, and removal of all plant leaves, with five repetitions. The genotype used for the evaluations was hybrid NB 7376. Defoliation was carried out when plants were at the growth stage R2. The variables assessed were: yield, density of spikes and corncobs, root resistance and stem integrity. When all leaves above the spike were removed, grain yield was reduced by 20%. Corncob density, stem integrity and root resistance to uprooting were also affected. Spike density was only affected when all plant leaves were removed. The leaf area remaining physiologically active above the spike was found to be most efficient in terms of grain yield.

A creative solution for rapid and inexpensive model-making in product design processes

Innovative Developments in Virtual and Physical Prototyping

Stress affects theta activity in limbic networks and impairs novelty-induced exploration and familiarization

Exposure to a novel environment triggers the response of several brain areas that regulate emotional behaviors. Here, we studied theta oscillations within the hippocampus (HPC)-amygdala (AMY)-medial prefrontal cortex (mPFC) network in exploration of a novel environment and subsequent familiarization through repeated exposures to that same environment; in addition, we assessed how concomitant stress exposure could disrupt this activity and impair both behavioral processes. Local field potentials were simultaneously recorded from dorsal and ventral hippocampus (dHPC and vHPC respectively), basolateral amygdala (BLA) and mPFC in freely behaving rats while they were exposed to a novel environment, then repeatedly re-exposed over the course of 3 weeks to that same environment and, finally, on re-exposure to a novel unfamiliar environment. A longitudinal analysis of theta activity within this circuit revealed a reduction of vHPC and BLA theta power and vHPC-BLA theta coherence through familiarization which was correlated with a return to normal exploratory behavior in control rats. In contrast, a persistent over-activation of the same brain regions was observed in stressed rats that displayed impairments in novel exploration and familiarization processes. Importantly, we show that stress also affected intra-hippocampal synchrony and heightened the coherence between vHPC and BLA. In summary, we demonstrate that modulatory theta activity in the aforementioned circuit, namely in the vHPC and BLA, is correlated with the expression of anxiety in novelty-induced exploration and familiarization in both normal and pathological conditions.

On the discovery of business processes orchestration patterns

COORDINSPECTOR is a Software Tool aiming at extracting the coordination layer of a software system. Such a reverse engineering process provides a clear view of the actually invoked services as well as the logic behind such invocations. The analysis process is based on program slicing techniques and the generation of, System Dependence Graphs and Coordination Dependence Graphs. The tool analyzes Common Intermediate Language (CIL), the native language of the Microsoft .Net Framework, thus making suitable for processing systems developed in any .Net Framework compilable language. COORDINSPECTOR generates graphical representations of the coordination layer together with business process orchestrations specified in WSBPEL 2.0

A creative solution for rapid and inexpensive model-making in product design processes

Rapid prototyping (RP) is an approach for automatically building a physical object through solid freeform fabrication. Nowadays, RP has become a vital aspect of most product development processes, due to the significant competitive advantages it offers compared to traditional manual model making. Even in academic environments, it is important to be able to quickly create accurate physical representations of concept solutions. Some of these can be used for simple visual validation, while others can be employed for ergonomic assessment by potential users or even for physical testing. However, the cost of traditional RP methods prevents their use in most academic environments on a regular basis, and even for very preliminary prototypes in many small companies. That results in delaying the first physical prototypes to later stages, or creating very rough mock-ups which are not as useful as they could be. In this paper we propose an approach for rapid and inexpensive model-making, which was developed in an academic context, and which can be employed for a variety of objects.

PHB-PEO electrospun fiber membranes containing chlorhexidine for drug delivery applications

Fiber meshes of poly(hydroxybutyrate) (PHB) and poly(hydroxybutyrate)/ poly(ethylene oxide) (PHB/PEO) with different concentrations of chlorhexidine (CHX) were prepared by electrospinning, for assessment as a polymer based drug delivery system. The electrospun fibers were characterized at morphological, molecular and mechanical levels. The bactericidal potential of PHB and PHB/PEO electrospun fibers with and without CHX was investigated against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) by disk diffusion susceptibility tests. Electrospun fibers containing CHX exhibited bactericidal activity. PHB/PEO-1%CHX displayed higher CHX release levels and equivalent antibacterial activity when compared to PHB/PEO with 5 and 10 wt% CHX. Bactericidal performance of samples with 1 wt% CHX was assessed by Colony Forming Units (CFU), where a reduction of 100 % and 99.69 % against E. coli and S. aureus were achieved, respectively.

Yield and nutrition of sunflower fertilized with sewage sludge stabilized by different processes

The different methods of sewage sludge stabilization modify their physical chemical and biological properties, altering its efficiency when applied in agriculture. The objective of this study was to evaluate the nutrient levels in soil and the yield of sunflower fertilized with sewage sludge stabilized by different processes. The experiment was conducted in Cambisol, with the treatments: control (without fertilization), fertilization with sewage sludge solarized, composted, vermicomposted, limed and chemical fertilizer recommended for sunflower crop. The experimental design a randomized block with four replications. The different methods of sewage sludge treatment did not affect the yield; however, the application of sewage sludge, regardless the stabilization process adopted, was more effective than chemical fertilizer and the control treatment. Overall, fertilization with limed sewage sludge provided higher soil nutrients concentrations, while treatments with composted and vermicomposted sewage sludge showed higher levels of nutrients in the plant.

Application of Gage R&R methodology for improving the training and evaluation of automatic optical inspection machine operators

The current level of demand by customers in the electronics industry requires the production of parts with an extremely high level of reliability and quality to ensure complete confidence on the end customer. Automatic Optical Inspection (AOI) machines have an important role in the monitoring and detection of errors during the manufacturing process for printed circuit boards. These machines present images of products with probable assembly mistakes to an operator and him decide whether the product has a real defect or if in turn this was an automated false detection. Operator training is an important aspect for obtaining a lower rate of evaluation failure by the operator and consequently a lower rate of actual defects that slip through to the following processes. The Gage R&R methodology for attributes is part of a Six Sigma strategy to examine the repeatability and reproducibility of an evaluation system, thus giving important feedback on the suitability of each operator in classifying defects. This methodology was already applied in several industry sectors and services at different processes, with excellent results in the evaluation of subjective parameters. An application for training operators of AOI machines was developed, in order to be able to check their fitness and improve future evaluation performance. This application will provide a better understanding of the specific training needs for each operator, and also to accompany the evolution of the training program for new components which in turn present additional new difficulties for the operator evaluation. The use of this application will contribute to reduce the number of defects misclassified by the operators that are passed on to the following steps in the productive process. This defect reduction will also contribute to the continuous improvement of the operator evaluation performance, which is seen as a quality management goal.