Pineapple Leaf Fibers for Composites and Cellulose

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Quantum chemical modeling of perovskite: An investigation of piezoelectricity in ferrite of yttrium

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Luminescent nano-composites generated from a spray

The spray-pyrolysis (SP) synthesis technique has been employed to obtain SiO2:Eu3+ and gamma-AlOOH:Eu3+, It was possible to obtain sub-micrometric spherical particles of SiO2 with luminescent Eu3+ ions bonded to the silica surface or embedded in amorphous silica beads, by controlling the synthesis and annealing process. Boehmite y-AlOOH doped with Eu3+ nanoparticles were synthesized by SP at moderate temperature (200 degrees C) with Eu3+ ions bonded to the surface hydroxyls of the boehmite nanocrystals. Luminescent nanocomposites were obtained by controlled reaction of gamma-AlOOH:Eu3+ nanocrystals with ASN (asparagine). In these nano-composites, the Eu3+ are held at the surface of the boehmite nanocrystals and partially shielded from interactions with additional luminescence quenchers (hydroxyl groups, water molecules). (C) 2008 Elsevier B.V. All rights reserved.

Population dynamics of Leptopharsa heveae (Hemiptera: Tingidae) and Erythmelus tingitiphagus (Hymenoptera: Mymaridae) in rubber tree plants

The tingid Leptopharsa heveae, known as the lace bug, occurs in large populations in rubber tree plantations, limiting the production of latex due to losses of photosynthetic area and weakening of the infested trees. The alternative for the use of insecticides would be the release of biological control agents, but little is known about the natural enemies of L. heveae. The parasitoid Erythmelus tingitiphagus parasitizes eggs of the lace bug in rubber tree plantations. The knowledge of the population dynamics and the peak of occurrence of economically important insect species and their natural enemies are indispensable requirements for the establishment of efficient and rational control strategies. The objective of this work was to study the population dynamics of L. heveae and E. tingitiphagus in rubber tree plantations in the county of Itiquira, MT, Brazil. Mature folioles were collected weekly from the lower stratum of the canopy of the tree clones RRIM 600, PR 255, GT 1, PB 235 and PB 217, from August/2005 to February/2006. The parasitoid was observed during the whole study period. The population peaks of the populations of the L. heveae and E. tingitiphagus in the study area occurred at the end of October and beginning of November. This result demonstrates that measures for the control of L. heveae and population increase of E. tingitiphagus must be adopted before the peak population of this pest in cultivated rubber plantations.

Piezoelectric behavior of SrRuO(3) buffered lanthanum modified bismuth ferrite thin films grown by chemical method

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Electric and magnetic properties of polymer electrolyte/carbon black composites

Measurements of 1H Nuclear Magnetic Resonance (NMR) relaxation times, Electron Paramagnetic Resonance (EPR) and AC Impedance Spectroscopy (IS) are reported for composites based on PEO8:LiClO4 and carbon black (CB), prepared by two methods: solvent and fusion processing. Three nuclear relaxation processes were identified for 1H nuclei: (i) belonging to the polymer chains in the amorphous phase, loosely bound to the CB particles, whose dynamics is almost the same as for unfilled polymer, (ii) belonging to the polymer chains which are tightly attached to the CB particles, and (iii) belonging to the crystalline phase in the loose polymer chain. The paramagnetic electronic susceptibility of the composite samples, measured by EPR, was interpreted by assuming a contribution of localized spin states that follow a Curie law, and a Pauli-like contribution of delocalized spins. A significant change of the EPR linewidth was observed at 40 K, which is the temperature where the Curie and Pauli susceptibilities equally contribute to the paramagnetic electronic susceptibility. The electrical properties are very sensitive to the preparation methods of the composites, which conditions the interaction between carbon particle-carbon particle and carbon particle-polymer chain. Classical statistic models to describe the conductivity in these media were not satisfactory. © 1998 Published by Elsevier Science B.V. All rights reserved.

Re-evaluation of antibiotic and mercury resistance in Escherichia coli populations isolated in 1978 from Amazonian rubber tree tappers and Indians

A study was carried out to assess the stability of antimicrobial susceptibility of wild isolates upon long-term storage using fifty-three Escherichia coli strains isolated in 1978 from feces of healthy children from the Amazon region in Brazil, exposed to low levels of antimicrobial agents, and examined for resistance to mercury and four antibiotics. All of the strains were kept in Lignieres medium at room temperature and were transferred to fresh media four times during this period. Thirty-five out of the 53 strains analyzed in 1978 were viable. Upon recovery, antibiotic and mercury resistance was estimated. All of the 35 strains maintained their original phenotype in a stable fashion, except for one multiresistant strain which became susceptible to kanamycin. Fifty-four percent of the strains exhibited a resistance phenotype, among which 47% had conjugative plasmids.

Unsaturated polyester based composites reinforced with curauá fiber - Preliminary studies

Curauá fiber processing characterization has been performed throughout the different processing steps. Unsaturated polyester has been used as matrix in the production of curauá reinforced composite samples. Compression molding process has been used to prepare the samples. Tensile strength, impact resistance, flexural strength, Young's modulus and elongation at break have been accessed for curauá composites in comparison with fiberglass composites. Mechanical properties were found not to attend the company's internal standards specification. However, the work has shown some alternatives to solve these problems such as the modification of equipment characteristics and resin formulation, the necessity of incorporation of a higher content of fiber and the possibility of using a new type of filler. Copyright © 2000 Society of Automotive Engineers, Inc.

Natural fiber reinforced unsaturated polyester composites - An approach on compression molding

This work has been performed at Tapetes Sao Carlos-Brazil with the cooperation of the DaimlerChrysler Research Center Team in Ulm - Germany. The objective of the present paper is to report the results obtained with natural fiber reinforced unsaturated polyester (UP) composites, concerning surface quality measurements. The fibers that have been chosen for this work were sisal and curaua. The samples were produced by compression molding technique and afterwards submitted to three different tests, namely: a) thermal aging; b) water absorption and c) artificial weathering. The surface parameters measured before and after the tests were gloss, haze, short and long-waviness. The results have shown that after the tests there is a high loss of gloss, a high increase in haze, and a high increase in short and long-waviness as well. Curaua reinforced composites had a slightly better behavior when compared with sisal reinforced composites. The effect of the presence of filler and the addition of thermoplastic polyester (TP) on the material behavior has not been evidently detected. This result shows that the conventional technology/methods applied to UP-Fiberglass systems cannot be transferred to natural fibers without any modification. The fiber-matrix interaction and its response to the presence of additives must be fully understood before a successful processing route can be developed for painted natural fibers reinforced UP. Copyright © 2001 Society of Automotive Engineers, Inc.

Friction and wear properties of functionally graded aluminum matrix composites

Aluminum matrix composites are currently considered as promising materials for tribological applications in the automotive, aircraft and aerospace industries due to their great advantage of a high strength-to-weight ratio. A superior combination of surface and bulk mechanical properties can be attained if these composites are processed as functionally graded materials (FGM's). In this work, homogeneous aluminum based matrix composite, cast by gravity, and aluminum composites with functionally graded properties, obtained by centrifugal cast, are tested against nodular cast iron in a pin-on-disc tribometer. Three different volume fractions of SiC reinforcing particles in each FGM were considered in order to evaluate their friction and wear properties. The sliding experiments were conducted without lubrication, at room temperature, under a normal load of 5 N and constant sliding speed of 0.5 ms-1. The worn surfaces as well as the wear debris were characterized by SEM/EDS and by atomic force microscopy (AFM). The friction coefficient revealed a slightly decrease (from 0.60 to 0.50) when FGM's are involved in the contact instead of the homogeneous composite. Relatively low values of the wear coefficient were obtained for functionally graded aluminum matrix composites (≈10-6 mm3N-1 m-1), which exhibited superior wear resistance than the homogeneous composite and the opposing cast iron surface. Characterization of worn surfaces indicated that the combined effect of reinforcing particles as load bearing elements and the formation of protective adherent iron-rich tribolayers has a decisive role on the friction and wear properties of aluminum matrix composites.

Thermogravimetric studies of the decomposition kinetics of four different Hevea rubber clones using Ozawa's approach

Thermal degradation of natural rubber extracted from four different rubber clones of the Hevea brasiliensis species was investigated by thermogravimetry using Ozawa's approach to assess the kinetic parameters of the decomposition process. The results are discussed in terms of the order of reaction, kinetic parameters such as activation energy as a function of conversion degree, and thermal stability for each of the clones.

Mortar added by tyre rubber residues: Characterisation in fresh and hardened state

Due to the progressive increase of vehicles, the number of used tires is globally one of the serious environmental problems faced now. Therefore, several researches have being developed for its reuse. The use of tires' rubber in the concrete is a possible form of its application, aiming at the recycling of this material and the improvement of certain properties, as tenacity, impact resistance, thermal and acoustic isolation. This article presents conclusions that several researchers obtained using the rubberized concrete. Thus there were researched several works enclosing the period of 1993 to 2003, presenting then the results of some characteristics of this concrete such as: physical properties in fresh and hardened state, mechanical properties and properties that remit the durability. The bibliographical revision has as objective to subsidize future researches that can contribute to improve the use of this concrete in civil construction.

Molecular phylogenetic and morphological analyses of Oidium heveae, a powdery mildew of rubber tree

Powdery mildew of rubber tree caused by Oidium heveae is an important disease of rubber plantations worldwide. Identification and classification of this fungus is still uncertain because there is no authoritative report of its morphology and no record of its teleomorphic stage. In this study, we compared five specimens of the rubber powdery mildew fungus collected in Malaysia, Thailand, and Brazil based on morphological and molecular characteristics. Morphological results showed that the fungus on rubber tree belongs to Oidium subgen. Pseudoidium. Nucleotide sequence analysis of the ribosomal DNA internal transcribed spacer (ITS) region and the large subunit rRNA gene (28S rDNA) were conducted to determine the relationships of the rubber powdery mildew fungus and to link this anamorphic fungus with its allied teleomorph. The results showed that the rDNA sequences of the two specimens from Malaysia were identical to a specimen from Thailand, whereas they differed by three bases from the two Brazilian isolates: one nucleotide position in the ITS2 and two positions in the 28S sequences. The ITS sequences of the two Brazilian isolates were identical to sequences of Erysiphe sp. on Quercus phillyraeoides collected in Japan, although the 28S sequences differed at one base from sequences of this fungus. Phylogenetic trees of both rDNA regions constructed by the distance and parsimony methods showed that the rubber powdery mildew fungus grouped with Erysiphe sp. on Q. phillyraeoides with 100% bootstrap support. Comparisons of the anamorph of two isolates of Erysiphe sp. from Q. phillyraeoides with the rubber mildew did not reveal any obvious differences between the two powdery mildew taxa, which suggests that O. heveae may be an anamorph of Erysiphe sp. on Q. phillyraeoides. Cross-inoculation tests are required to substantiate this conclusion. © The Mycological Society of Japan and Springer-Verlag 2005.

Age-age correlation for early selection of rubber tree genotypes in São Paulo State, Brazil

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Genetic variation in growth traits and yield of rubber trees (Hevea brasiliensis) growing in the Brazilian state of São Paulo

Analysis of variance and covariance was preformed on growth traits (stem girth, bark thickness, total height gain and rubber yield) of 22 open-pollinated progenies of the rubber tree Hevea brasiliensis from an Asian Hevea collection introduced to Agronomic Institute (Instituto Agronômico, Campinas, São Paulo, Brazil; IAC) in 1952. This progeny trial was replicated at three sites in São Paulo state and it was found that at three years from sowing there was statistically significant variation for girth, bark thickness, height and rubber yield. An individual test sites, values of individual plant heritability for girth ranged from ĥ i 2 = 0.36 to ĥ i 2 = 0.89 whereas values for heritability for progeny means ranged from ĥ i 2 = 0.77 to ĥ i 2 = 0.87. These moderate and high heritabilities suggest that a combination of progeny and within-progeny selection would be effective at increasing girth in this population at individual sites. Across sites, values of individual-plant heritability for girth ranged from ĥ i 2 = 0.36 to ĥ i 2 = 0.47, whereas values for heritability of progeny means girth ranged from ĥ x̄ 2 = 0.77 to ĥ x̄ 2 = 0.87. There were high positive genetic correlations between increased girth and bark thickness suggesting that breeding aimed at increasing girth would also increase bark thickness and possibly height. Copyright by the Brazilian Society of Genetics.