Catalysts study of adipic acid synthesis from 1,6-hexanediol

Sustainable chemicals currently have a very limited market share due to current low production but biomass is expected to become one of the major renewable energy and fine chemicals sources in the coming years. Bearing in mind the compromise of all nations to climatic change remediation, the industries will need to use efficient catalysts and green processes to meet the requirements of emissions and efficiency. This project is expected to develop new catalysts to convert 1,6-hexanediol to adipic acid through a green approach based on the “nano-catalysis” and “green chemistry” concepts. Supported Au and Pd nanoparticles were used to study one-pot reaction of HDO oxidation to AA using O2 as a final oxidant and H2O as a solvent. Catalytic results showed that under low pressure O2 atmosphere and low temperature (< 120°C) AuNPs supported on basic-supports are more active than acid and amphoteric oxides. The effect of basic oxide (MgO) addition to MgF2 was studied. The study showed that doping of MgF2 with MgO increased significantly the activity of the catalyst. The best results were obtained with the Au/0.4MgF2-0.6MgO sample, which gave the selectivity to AA of 33% at HDO conversion of 62%.

Investigation of gold-based catalysts for liquid phase oxidation of glucose to glucaric acid

Glucaric acid (GA) is one of the building block chemicals derived from sugar biomass with higher added value. Nowadays, GA is produced by oxidation of glucose (Glu) with either stoichiometric oxidants (HNO3), or by means of electrochemical or biochemical synthesis. However, these processes show drawbacks from either the environmental or economic viewpoint. For this reason, gold nanoparticles (Au NPs) supported on activated carbon (AC) have been studied as catalysts for the oxidation of Glu, using O2 as oxidant in the presence of a base. Using sol immobilization technique, Au NPs have been supported on AC following different experimental procedures. UV-Vis spectroscopy, XRD, TEM and TG analysis were utilized in the characterization of the catalysts. The operational conditions were optimized obtaining 24% of yield of GA, 37% to GO and 27% to byproducts in 1 h, 1000 rpm, 10 bar of O2 and Glu:Au:NaOH molar ratio of 1000:1:3000. Under such conditions, catalysts show relatively high Glu conversion (≥82%) with different GA yields. GO+GA yield is around 58-61%. Therefore, the oxidation reaction was performed at 15 min where Au/AC PVA0 reached the highest yield of GA (16%) and Au/AC PVA2.4 gave the lowest (8%). It is evident that the presence of PVA influences to a higher degree the reaction rate than the Au NPs size. Hence, the effect of different heat treatments where applied for the removal of PVA: washing with water at 60℃ or heat treatment (120-250℃) with Air/H2. Washing treatment and heat treatment at 120℃ with Air/H2 may have resulted in the mildest treatments for the removal of PVA. Finally, two different supports have been used in order to study the effect of metal-support interaction in the immobilization of Au NPs: ZrO2 and AC. Au/AC catalyst demonstrated a higher conversion of GO to GA at short reaction times (15.1% yield GA) compared to Au/ZrO2 (2.4% yield GA).

Supported metal nanoparticles for sustainable green catalytic processes

Preformed Au nanoparticles supported on activated carbon and TiO2 were synthesised by sol-immobilisation. Polyethylene glycol, polyvinyl pyrrolidone and polyvinyl alcohol were used as stabilisers for the gold nanoparticles at different polymer/Au wt/wt ratios for each polymer. The effect of polymer/Au wt/wt ratios was investigated on (i) the average nanoparticle size, (ii) catalytic activity for two reactions, 4-nitrophenol reduction and glucose oxidation to glucaric acid. 4-nitrophenol reduction is recognised as a model reaction for nanomaterial catalytic activity tests; glucose oxidation to glucaric acid is a reaction that is traditionally carried out with concentrated nitric acid, for which alternative reaction pathways are looked for in an effort to reduce its environmental impact. The catalysts were characterised from the nanoparticle synthesis by colloidal method by means of UV-vis spectroscopy and DLS analysis, to the immobilisation step by XRD and TEM. The effect of the polymer:Au wt/wt ratio on nanoparticle size depends on the polymer nature, and point out the need to optimise supported nanoparticle synthesis protocols in the future depending on the type of stabiliser. The catalytic tests revealed that the polymers interact with Au nanoparticles through different active sites. Activated carbon (AC) and TiO2 were compared as supports for Au nanoparticles stabilised by PVA at PVA/Au 0,65 wt/wt. AC-supported Au NPs were the most active for glucose oxidation while TiO2-stabilised Au NPs were five times more active in 4-nitrophenol reduction that AC-supported NPs. Hence support and stabiliser are important parameters that should be optimised in order to achieve high catalytic activity for a given reaction.

Deidrogenazione ossidativa del n-butano catalizzata da ossidi metallici difettivi

The oxidative dehydrogenation (ODH) of n-butane is a promising way to synthetize butenes and 1,3-butadiene, currently produced by steam cracking or direct dehydrogenation of n-butane. The addition of oxygen as a reagent leads to the formation of water, a very stable by-product, which makes the process exothermic.In this work, the ODH of n- butane was investigate to selectively obtain butenes and 1,3-butadiene. Four catalysts based on metal oxides (V2O5, La2O3, CeO2 and TiO2) were mixed with Mg metallic powder and reduced at 650 °C for 5 h in 5% H2/Ar atmosphere, with the purpose of creating oxygen vacancies in the crystal lattice of the oxides. Subsequently, the effect of the Mg concentration, and thus the oxygen vacancies concentration, was studied. The titanium oxide-based catalysts were the most active, in terms of butane conversion and selectivity to butenes and 1,3 butadiene. Overall, this study shows that the formation of oxygen vacancies on metal oxides can be influenced by the addition of metallic Mg during the synthesis. In the case of TiO2, this leads to an increase on the activity compared to the untreated sample.

Synthesis and characterisation of electrospun gold on ceria catalysts

Cerium oxide in catalysis can be used both as support and as a catalyst itself. Ceria catalyses many oxidations reactions, its excellent catalytic properties are due to its store oxygen storage capacity (OSC) and the reticular defects present on its surface. Different morphologies expose different reticular planes, and different reticular planes can expose different amounts of defects. The preparation method of cerium oxide can influence the surface area, morphology, and the number of defects in the sample. This work is focused on different preparation methods for gold nanoparticles supported on 1D nanostructures of cerium oxide prepared via electrospinning, their XRD, DRUV-Vis and Raman characterizations, and their catalytic performance on the oxidation reaction of HMF to FDCA.

Valorization of bio-alcohols into added value chemicals

The present research work focused on the valorisation and upgrading of bio-ethanol over heterogeneous catalysts in a lab-scale continuous gas-flow system. In the Unibo laboratories, catalytic tests have been carried out in the temperature range 300-600°C by feeding an ethanol/He mixture in the reactor. After choosing the reaction conditions, ion-exchanged hydroxyapatite with transition metals (i.e., Fe, Cu) and alkaline earth metal (i.e., Sr) have been synthesized and tested. The Sr-HAP catalyst led to the formation of a complex reaction mixture the composition of which need further optimization in order to fill the requisite to be used as fuel-blend. Then, some zirconium-oxide based catalysts have been prepared through two different methods, precipitation and hydrothermal, by varying some synthetic parameters (i.e., pH, the nature of the base) and by adding a transition metal as dopant agent (i.e., Ti and Y). The presence of a dopant into the zirconia structure favoured the stabilization of the tetragonal or cubic phase against the monoclinic one. Interestingly, 5%mol Ti-doped zirconia exhibited a different catalytic behaviour yielding diethyl ether as major product at 300°C, while all the others samples produced mainly ethylene. Then, the effect of acid-base properties of sepiolite, using alkali metals (i.e., Na, K, Cs) with different metal loading (i.e., 2, 4, 5, 7, 14 wt%) as promoters, and of the redox properties of sepiolite-supported CuO or NiO, on the catalytic conversion of ethanol into n-butanol has been investigated. Thermal treated sepiolite samples mainly acted as acid catalyst, yielding preferentially the dehydration products of ethanol (ethylene and diethyl ether). Best results in terms of activity (ethanol conversion, 59%) and n-butanol selectivity (30%) where obtained at 400ºC and a contact time, W/F, of 2 g/mL·s over the catalyst consisting of sepiolite calcined at 500ºC modified with 7 wt% of cesium.

Determination of local density of states in amorphous oxide semiconductors with Kelvin Probe Force Microscopy

Amorphous semiconductors are important materials as they can be deposited by physical deposition techniques on large areas and even on plastic substrates. Therefore, they are crucial for transistors in large active matrices for imaging and transparent wearable electronics. The most widely applied candidate for amorphous thin film transistors production is Indium Gallium Zinc Oxide (IGZO). It is attracting much interest because of its optical transparency, facile processing by sputtering deposition and notable improved charge carrier mobility with respect to hydrogenated amorphous silicon a-Si:H. Degradation of the device and long-term performance issues have been observed if IGZO thin film transistors are subjected to electrical stress, leading to a modification of IGZO channel properties and subthreshold slope. Therefore, it is of great interest to have a reliable and precise method to study the conduction band tail, and the density of states in amorphous semiconductors. The aim of this thesis is to develop a local technique using Kelvin Probe Force Microscopy to study the evolution of IGZO DOS properties. The work is divided into three main parts. First, solutions to the non-linear Poisson-Boltzmann equation of a metal-insulator-semiconductor junction describing the charge accumulation and its relation to DOS properties are elaborated. Second macroscopic techniques such as capacitance voltage (CV) measurements and photocurrent spectroscopy are applied to obtain a non-local estimate of band-tail DOS properties in thin film transistor samples. The third part of my my thesis is dedicated to the KPFM measurements. By fitting the data to the developed numerical model, important parameters describing the amorphous conduction band tail are obtained. The results are in excellent agreement with the macroscopic characterizations. KPFM result is comparable also with non-local optoelectronic characterizations, such as photocurrent spectroscopy.

Niobium-based heterogeneous catalysts synthesised in supercritical carbon dioxide for selective olefin epoxidation

In this work, two different protocols for the synthesis of Nb2O5-SiO2 with a sol-gel route in which supercritical carbon dioxide was used as solvent have been developed. The tailored design of the reactor allowed the reactants to come into contact only when supercritical CO2 is present, and the high-throughput experimentation scCO2 unit allowed the screening of synthetic parameters, that led to a Nb2O5 incorporation into the silica matrix of 2.5 wt%. N2-physisorption revealed high surface areas and the presence of meso- and micropores. XRD allowed to demonstrate the amorphous character of these materials. SEM-EDX proved the excellent dispersion of Nb2O5 into the silica matrix. These materials were tested in the epoxidation of cyclooctene with hydrogen peroxide, which is considered an environmentally friendly oxidant. The catalysts were virtually inactive in an organic, polar, aprotic solvent (1,4-dioxane). However, the most active scCO2 Nb2O5-SiO2 catalyst achieved a cyclooctene conversion of 44% with a selectivity of 88% towards the epoxide when tested in ethanol. Catalytic tests on cyclohexene revealed the presence of the epoxide, which is remarkable, considering that this substrate is easily oxidised to the diol. The behaviour in protic and aprotic solvents is compared to that of TS-1.

Geochemistry Of Acid Mine Drainage From A Coal Mining Area And Processes Controlling Metal Attenuation In Stream Waters, Southern Brazil.

Acid drainage influence on the water and sediment quality was investigated in a coal mining area (southern Brazil). Mine drainage showed pH between 3.2 and 4.6 and elevated concentrations of sulfate, As and metals, of which, Fe, Mn and Zn exceeded the limits for the emission of effluents stated in the Brazilian legislation. Arsenic also exceeded the limit, but only slightly. Groundwater monitoring wells from active mines and tailings piles showed pH interval and chemical concentrations similar to those of mine drainage. However, the river and ground water samples of municipal public water supplies revealed a pH range from 7.2 to 7.5 and low chemical concentrations, although Cd concentration slightly exceeded the limit adopted by Brazilian legislation for groundwater. In general, surface waters showed large pH range (6 to 10.8), and changes caused by acid drainage in the chemical composition of these waters were not very significant. Locally, acid drainage seemed to have dissolved carbonate rocks present in the local stratigraphic sequence, attenuating the dispersion of metals and As. Stream sediments presented anomalies of these elements, which were strongly dependent on the proximity of tailings piles and abandoned mines. We found that precipitation processes in sediments and the dilution of dissolved phases were responsible for the attenuation of the concentrations of the metals and As in the acid drainage and river water mixing zone. In general, a larger influence of mining activities on the chemical composition of the surface waters and sediments was observed when enrichment factors in relation to regional background levels were used.

Electronic And Structural Study Of Pt-modified Au Vicinal Surfaces: A Model System For Pt-au Catalysts.

Two single crystalline surfaces of Au vicinal to the (111) plane were modified with Pt and studied using scanning tunneling microscopy (STM) and X-ray photoemission spectroscopy (XPS) in ultra-high vacuum environment. The vicinal surfaces studied are Au(332) and Au(887) and different Pt coverage (θPt) were deposited on each surface. From STM images we determine that Pt deposits on both surfaces as nanoislands with heights ranging from 1 ML to 3 ML depending on θPt. On both surfaces the early growth of Pt ad-islands occurs at the lower part of the step edge, with Pt ad-atoms being incorporated into the steps in some cases. XPS results indicate that partial alloying of Pt occurs at the interface at room temperature and at all coverage, as suggested by the negative chemical shift of Pt 4f core line, indicating an upward shift of the d-band center of the alloyed Pt. Also, the existence of a segregated Pt phase especially at higher coverage is detected by XPS. Sample annealing indicates that the temperature rise promotes a further incorporation of Pt atoms into the Au substrate as supported by STM and XPS results. Additionally, the catalytic activity of different PtAu systems reported in the literature for some electrochemical reactions is discussed considering our findings.

Bipolar Tribocharging Signal During Friction Force Fluctuations At Metal-insulator Interfaces.

Friction and triboelectrification of materials show a strong correlation during sliding contacts. Friction force fluctuations are always accompanied by two tribocharging events at metal-insulator [e.g., polytetrafluoroethylene (PTFE)] interfaces: injection of charged species from the metal into PTFE followed by the flow of charges from PTFE to the metal surface. Adhesion maps that were obtained by atomic force microscopy (AFM) show that the region of contact increases the pull-off force from 10 to 150 nN, reflecting on a resilient electrostatic adhesion between PTFE and the metallic surface. The reported results suggest that friction and triboelectrification have a common origin that must be associated with the occurrence of strong electrostatic interactions at the interface.

Compact Ag@fe3o4 Core-shell Nanoparticles By Means Of Single-step Thermal Decomposition Reaction.

A temperature pause introduced in a simple single-step thermal decomposition of iron, with the presence of silver seeds formed in the same reaction mixture, gives rise to novel compact heterostructures: brick-like Ag@Fe3O4 core-shell nanoparticles. This novel method is relatively easy to implement, and could contribute to overcome the challenge of obtaining a multifunctional heteroparticle in which a noble metal is surrounded by magnetite. Structural analyses of the samples show 4 nm silver nanoparticles wrapped within compact cubic external structures of Fe oxide, with curious rectangular shape. The magnetic properties indicate a near superparamagnetic like behavior with a weak hysteresis at room temperature. The value of the anisotropy involved makes these particles candidates to potential applications in nanomedicine.

S-nitrosothiols Regulate Nitric Oxide Production And Storage In Plants Through The Nitrogen Assimilation Pathway.

Nitrogen assimilation plays a vital role in plant metabolism. Assimilation of nitrate, the primary source of nitrogen in soil, is linked to the generation of the redox signal nitric oxide (NO). An important mechanism by which NO regulates plant development and stress responses is through S-nitrosylation, that is, covalent attachment of NO to cysteine residues to form S-nitrosothiols (SNO). Despite the importance of nitrogen assimilation and NO signalling, it remains largely unknown how these pathways are interconnected. Here we show that SNO signalling suppresses both nitrate uptake and reduction by transporters and reductases, respectively, to fine tune nitrate homeostasis. Moreover, NO derived from nitrate assimilation suppresses the redox enzyme S-nitrosoglutathione Reductase 1 (GSNOR1) by S-nitrosylation, preventing scavenging of S-nitrosoglutathione, a major cellular bio-reservoir of NO. Hence, our data demonstrates that (S)NO controls its own generation and scavenging by modulating nitrate assimilation and GSNOR1 activity.

Hdl Levels And Oxidizability During Myocardial Infarction Are Associated With Reduced Endothelial-mediated Vasodilation And Nitric Oxide Bioavailability.

Acute phase response modifies high-density lipoprotein (HDL) into a dysfunctional particle that may favor oxidative/inflammatory stress and eNOS dysfunction. The present study investigated the impact of this phenomenon on patients presenting ST-elevation myocardial infarction (STEMI). Plasma was obtained from 180 consecutive patients within the first 24-h of onset of STEMI symptoms (D1) and after 5 days (D5). Nitrate/nitrite (NOx) and lipoproteins were isolated by gradient ultracentrifugation. The oxidizability of low-density lipoprotein incubated with HDL (HDLaoxLDL) and the HDL self-oxidizability (HDLautox) were measured after CuSO4 co-incubation. Anti-inflammatory activity of HDL was estimated by VCAM-1 secretion by human umbilical vein endothelial cells after incubation with TNF-α. Flow-mediated dilation (FMD) was assessed at the 30(th) day (D30) after STEMI. Among patients in the first tertile of admission HDL-Cholesterol (<33 mg/dL), the increment of NOx from D1 to D5 [6.7(2; 13) vs. 3.2(-3; 10) vs. 3.5(-3; 12); p = 0.001] and the FMD adjusted for multiple covariates [8.4(5; 11) vs 6.1(3; 10) vs. 5.2(3; 10); p = 0.001] were higher than in those in the second (33-42 mg/dL) or third (>42 mg/dL) tertiles, respectively. From D1 to D5, there was a decrease in HDL size (-6.3 ± 0.3%; p < 0.001) and particle number (-22.0 ± 0.6%; p < 0.001) as well as an increase in both HDLaoxLDL (33%(23); p < 0.001) and HDLautox (65%(25); p < 0.001). VCAM-1 secretion after TNF-a stimulation was reduced after co-incubation with HDL from healthy volunteers (-24%(33); p = 0.009), from MI patients at D1 (-23%(37); p = 0.015) and at D30 (-22%(24); p = 0.042) but not at D5 (p = 0.28). During STEMI, high HDL-cholesterol is associated with a greater decline in endothelial function. In parallel, structural and functional changes in HDL occur reducing its anti-inflammatory and anti-oxidant properties.

Nitric Oxide-releasing Poly(vinyl Alcohol) Film For Increasing Dermal Vasodilation.

Pathological conditions associated with the impairment of nitric oxide (NO) production in the vasculature, such as Raynaud's syndrome and diabetic angiopathy, have stimulated the development of new biomaterials capable of delivering NO topically. With this purpose, we modified poly(vinyl-alcohol) (PVA) by chemically crosslinking it via esterification with mercaptosuccinic acid. This reaction allowed the casting of sulfhydrylated PVA (PVA-SH) films. Differential scanning calorimetry and X-ray diffractometry showed that the crosslinking reaction completely suppressed the crystallization of PVA, leading to a non-porous film with a homogeneous distribution of -SH groups. The remaining free hydroxyl groups in the PVA-SH network conferred partial hydrophylicity to the material, which was responsible for a swelling degree of ca. 110%. The PVA-SH films were subjected to an S-nitrosation reaction of the -SH groups, yielding a PVA containing S-nitrosothiol groups (PVA-SNO). Amperometric and chemiluminescence measurements showed that the PVA-SNO films were capable of releasing NO spontaneously after immersion in physiological medium. Laser Doppler-flowmetry, used to assess the blood flow in the dermal microcirculation, showed that the topical application of hydrated PVA-SNO films on the health skin led to a dose- and time-dependent increase of more than 5-fold in the dermal baseline blood flow in less than 10min, with a prolonged action of more than 4h during continuous application. These results show that PVA-SNO films might emerge as a new material with potential for the topical treatment of microvascular skin disorders.