Effect of heat input on the mechanical properties of welded joints in high strength steels

Experiments were carried out to determine the properties of the welded joints in 8mm thick high-strength steels produced by quenching and tempering and thermomechanical rolling with accelerated cooling (tensile strength 821–835 MPa). The dependence of the strength, elongation, hardness, impact energy and crack opening displacement on the heat input in the range 1.0–0.7 kJ mm21 was determined. The results show that the dependence of the strength of the welded joints decreases and that of the elongation increases. The heat input has only a slight effect on the impact energy and crack opening displacement in the heat-affected zone.

Monolithic zirconium dioxide as a full contour restorative material: With special emphasis on the optical and mechanical properties

Full contour monolithic zirconia restorations have shown an increased popularity in the dental field over the recent years, owing to its mechanical and acceptable optical properties. However, many features of the restoration are yet to be researched and supported by clinical studies to confirm its place among the other indirect restorative materials This series of in vitro studies aimed at evaluating and comparing the optical and mechanical properties, light cure irradiance, and cement polymerization of multiple monolithic zirconia material at variable thicknesses, environments, treatments, and stabilization. Five different monolithic zirconia materials, four of which were partially stabilized and one fully stabilized were investigated. The optical properties in terms of surface gloss, translucency parameter, and contrast ratio were determined via a reflection spectrophotometer at variable thicknesses, coloring, sintering method, and after immersion in an acidic environment. Light cure irradiance and radiant exposure were quantified through the specimens at variable thicknesses and the degree of conversion of two dual-cure cements was determined via Fourier Transform Infrared spectroscopy. Bi-axial flexural strength was evaluated to compare between the partially and fully stabilized zirconia prepared using different coloring and sintering methods. Surface characterization was performed using a scanning electron microscope and a spinning disk confocal microscope. The surface gloss and translucency of the zirconia investigated were brand and thickness dependent with the translucency values decreasing as the thickness increased. Staining decreased the translucency of the zirconia and enhanced surface gloss as well as the flexural strength of the fully stabilized zirconia but had no effect on partially stabilized zirconia. Immersion in a corrosive acid increased surface gloss and decreased the translucency of some zirconia brands. Zirconia thickness was inversely related to the amount of light irradiance, radiant exposure, and degree of monomer conversion. Type of sintering furnace had no effect on the optical and mechanical properties of zirconia. Monolithic zirconia maybe classified as a semi-translucent material that is well influenced by the thickness, limiting its use in the esthetic zones. Conventional acid-base reaction, autopolymerizing and dual-cure cements are recommended for its cementation. Its desirable mechanical properties give it a high potential as a restoration for posterior teeth. However, close monitoring with controlled clinical studies must be determined before any definite clinical recommendations can be drawn.

Determination of structural and mechanical properties, diffractometry, and thermal analysis of chitosan and hydroxypropylmethylcellulose (HPMC) films plasticized with sorbitol

In this work, the structural, mechanical, diffractometric, and thermal parameters of chitosan-hydroxypropylmethylcellulose (HPMC) films plasticized with sorbitol were studied. Solutions of HPMC (2% w/v) in water and chitosan (2% w/v) in 2% acetic acid solution were prepared. The concentration of sorbitol used was 10% (w/w) to both polymers. This solutions were mixed at different proportions (100/0; 70/30; 50/50; 30/70, and 0/100) of chitosan and HPMC, respectively, and 20 mL was cast in Petri dishes for further analysis of dried films. The miscibility of polymers was assessed by X-ray diffraction, scanning electronic microscopy (SEM), differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA). The results obtained indicate that the films are not fully miscible at a dry state despite the weak hydrogen bonding between the polymer functional groups.

Mechanical and water vapor permeability properties of biodegradables films based on methylcellulose, glucomannan, pectin and gelatin

Mimic biological structures such as the cell wall of plant tissues may be an alternative to obtain biodegradable films with improved mechanical and water vapor barrier properties. This study aims to evaluate the mechanical properties and water vapor permeability (WVP) of films produced by using the solvent-casting technique from blended methylcellulose, glucomannan, pectin and gelatin. First, films from polysaccharides at pH 4 were produced. The film with the best mechanical performance (tensile strength = 72.63 MPa; elongation = 9.85%) was obtained from methylcellulose-glucomannan-pectin at ratio 1:4:1, respectively. Then, gelatin was added to this polysaccharide blend and the pH was adjusted to 4, 5 and 6. Results showed significant improvement in WVP when films were made at pH 5 and at polysaccharides/gelatin ratio of 90/10 and 10/90, reaching 0.094 and 0.118 g.mm/h.m².kPa as values, respectively. Films with the best mechanical properties were obtained from the blend of polysaccharides, whereas WVP was improved from the blend of polysaccharides and gelatin at pH 5.

Effects of the mechanical damage on the water absorption process by corn kernel

The purpose of this study was to investigate and model the water absorption process by corn kernels with different levels of mechanical damage Corn kernels of AG 1510 variety with moisture content of 14.2 (% d.b.) were used. Different mechanical damage levels were indirectly evaluated by electrical conductivity measurements. The absorption process was based on the industrial corn wet milling process, in which the product was soaked with a 0.2% sulfur dioxide (SO2) solution and 0.55% lactic acid (C3H6O3) in distilled water, under controlled temperatures of 40, 50, 60, and 70 ºC and different mechanical damage levels. The Peleg model was used for the analysis and modeling of water absorption process. The conclusion is that the structural changes caused by the mechanical damage to the corn kernels influenced the initial rates of water absorption, which were higher for the most damaged kernels, and they also changed the equilibrium moisture contents of the kernels. The Peleg model was well adjusted to the experimental data presenting satisfactory values for the analyzed statistic parameters for all temperatures regardless of the damage level of the corn kernels.

Effect of incorporation of nutraceutical capsule waste of safflower oil in the mechanical characteristics of corn starch films

Abstract Biodegradable films blends made of safflower oil nutraceutical capsules waste corn starch (20:4, 30:4, 40:4 and 50:4) were prepared. The objective of this study was to evaluate the influence of addition of different concentrations of safflower oil nutraceutical capsule waste in the mechanical properties (tensile strength, elongation at break, Young’s modulus) and thickness of corn starch films. A decrease in tensile strength and Young’s modulus and an increase in elongation at break were observed with the increase in the content of the nutraceutical capsule waste. The results showed that the blends of safflower oil capsules waste-corn starch films demonstrated promising characteristics to form biodegradable films with different mechanical characteristics.

Mechanical design and optics simulation of the illuminated Volvo Iron mark

Utilization of light and illumination systems in automotive industry for different purposes has been increased significantly in recent years. Volvo as one of the leading companies in manufacturing of luxury cars has found the great capacity in this area. The performance of such an illumination systems is one of the challenges that engineers in this industry are facing with. In this study an effort has been made to design a system to make the iron mark of Volvo being illuminated and the system is being evaluated by optics simulation in software using Ray optics method. At the end, results are assessed and some optimizations are carried out. Different kind of light guides, front side of the iron mark and some possible arrangement for LED also evaluated and different materials tested. The best combination from uniformity, color and amount of luminance aspect selected as a possible solution for this special project which can be used as a base for further studies in Volvo.

X-Ray analysis to assess mechanical damage in sweet corn seeds

The X-ray test is a precise, fast and non-destructive method to detect mechanical damage in seeds. In the present study, the efficiency of X-ray analysis in identifying the extent of mechanical damage in sweet corn seeds and its relationship with germination and vigor was evaluated. Hybrid 'SWB 551' (sh2) seeds with round (R) and flat (F) shapes were classified as large (L), medium (M1, M2 and M3) and small (S), using sieves with round and oblong screens. After artificial exposure to different levels of damage (0, 1, 3, 5 and 7 impacts), seeds were X-rayed (15 kV, 5 min) and submitted to germination (25 °C/5 days) and cold (10 °C/7 days) tests. Digital images of normal and abnormal seedlings and ungerminated seeds from germination and cold tests were jointly analyzed with the seed X-ray images. Results showed that damage affecting the embryonic axis resulted in abnormal seedlings or dead seeds in the germination and cold tests. The X-ray analysis is efficient for identifying mechanical damage in sweet corn seeds, allowing damage severity to be associated with losses in germination and vigor.

The association between body composition and arterial stiffness in peri-pubescent children

The objective of this study was to examine the association between body composition and arterial stiffuess in peri-pubescent boys and girls. Differences in arterial distensibility were measured in 68 children (45 normal weight, 12 overweight, and 11 obese) between the ages of9 to 12 years. Weight classification was based on age and gender-specific body mass index cut-offs, while pubertal maturation was self-reported using Tanner staging. Distensibility was determined using two-dimensional, B-Mode echo Doppler ultrasound to measure changes at the right common carotid artery (CCA) diameter changes, while carotid pulse pressure (cPP) was measured at the left CCA by applanation tonometry. One-way ANOV A analysis revealed significant differences (p<0.001) in all anthropometric measures between the normal weight and overweight children, as well as the normal weight and obese children. Body stature was only higher in obese children compared to normal weight children (p<0.01). No significant differences were found between groups regarding age or Tanner stage. Common carotid artery distensibility showed a significant difference (p<0.01) between normal weight children (0.008 ± 0.002 mmHg-1 ) compared to obese children (0.005 ± 0.002 mmHg-1 ), with a borderline significant difference between the normal and overweight subjects (p=0.06). There was no significant effect for gender between males and females across all independent variables. The strongest determinants of distensibility in children were cPP (r= -0.52, p

ARTERIAL STIFFNESS IN CHILDREN WITH AND WITHOUT DEVELOPMENTAL COORDINATION DISORDER

The purpose of this study was to determine whether children with potential developmental coordination disorder (p-DCD) demonstrate increased arterial stiffness and thickness compared to age and school matched controls (mean age 14.7 yrs). We also assessed whether these measures differed by sex. Compliance, distensibility, and intima-media thickness (IMT) were measured at the common carotid artery for 28 children with p-DCD and 47 controls. ECG-R-wave-toe pulse wave velocity (PWV) was also measured for 29 children with p-DCD and 45 controls. We found that compared to controls males with p-DCD had significantly higher PWV (3.8±0.2 vs. 4.1±0.3, p=0.001) and lower distensibility (0.82± 0.19 vs. 0.70± 0.17, p=0.034) while females showed no significant differences (p=0.523 and p=0.123 respectively). As a result, it is apparent that sex differences exist with respect to arterial health within this population and that children with p-DCD may be more likely to develop cardiovascular disease later in life.

The Influence of Sex on the Relationship Between Arterial Mechanical Properties and Cardiovagal Baroreflex Sensitivity

Cardiovagal baroreflex sensitivity (cvBRS) demonstrates a strong relationship with arterial mechanical properties. Both cvBRS and arterial mechanics differ by sex such that males demonstrate greater cvBRS, yet lower large artery elasticity than females. Whether the relationship between cvBRS and arterial mechanics is similar in males and females remains unexamined. As a result, it is unclear whether arterial mechanics contribute to sex differences in cvBRS. This study investigated the cross-sectional relationship between cvBRS and arterial mechanical properties of the common carotid, carotid sinus and aortic arch (AA) in 36 (18 females) young, healthy normotensives. The cvBRS-arterial mechanics relationship did not reach statistical significance and did not differ by sex. Both cvBRS and AA distensibility were greater in females than males. Sex differences in cvBRS were eliminated after controlling for AA distensibility. These findings suggest that in this sample, AA elasticity may contribute to the greater cvBRS in females than males.

Relation entre la structure et la fonction des artères cérébrales dans l’athérosclérose : impact des traitements cardioprotecteurs

Thèse réalisée en cotutelle avec Dre Christine Des Rosiers

Étude comparative des propagules extraracinaires et intraracinaires du champignon mycorhizien Glomus irregulare

La germination des spores est une étape essentielle dans le cycle de vie de la majorité des champignons filamenteux. Les champignons mycorhiziens à arbuscules (CMA) forment un certain nombre de propagules infectieuses différentes qui augmentent leur potentiel à coloniser les racines. Parmi elles se trouvent les spores extraracinaires et intraracinaires. La paroi cellulaire des spores joue un rôle majeur dans la survie de ces propagules en étant une barrière physique et osmotique. Puisque une cellule peut faire des ajustements considérables dans la composition et la structure de sa paroi, en réponse aux conditions environnementales, il est possible que les parois des spores intraracinaires et extraracinaires montrent des propriétés mécaniques et osmotiques différentes affectant leur germination et leur survie. Pourtant, contrairement à la connaissance de la génétique moléculaire et de la formation de la paroi cellulaire des CMA, peu d’information est disponible au sujet de ces propriétés mécaniques. Les informations sur la germination des CMA dans des conditions hypertoniques sont aussi rares, et les modèles expérimentaux ne séparent généralement pas les effets directs de la forte pression osmotique externe sur la germination des champignons et les effets attribuables aux plantes. Cette étude avait pour but de répondre à deux importantes séries de questions concernant le comportement des spores mycorhiziennes. Nous avons d'abord déterminé la relation entre la composition de la paroi cellulaire, la structure et les propriétés mécaniques du champignon modèle Glomus irregulare (isolat DAOM 197198). La micro-indentation a été utilisée pour mesurer quantitativement les propriétés mécaniques de la paroi cellulaire. La composition (contenu de chitine et de glomaline) de la paroi cellulaire a été quantifiée par immunofluorescence tandis que la microscopie optique a été utilisée pour mesurer l'épaisseur de la paroi cellulaire. La densité locale en glomaline et l’épaisseur de la paroi étaient significativement plus élevées pour les parois des spores extraracinaires alors que la densité locale en chitine et la rigidité n’ont pas montré de variations entre les spores extraracinaires et intraracinaires. La grande variabilité dans les paramètres étudiés nous a empêchés de cibler un facteur principal responsable de la force totale de la paroi lors de la compression. La diminution des concentrations de chitine et de glomaline a été corrélée à l'évolution de la paroi du champignon au cours de son cycle de vie. On a aussi observé une composition différentielle des couches de la paroi: les polymères de chitine et de glomaline furent localisés principalement dans les couches externes et internes de la paroi, respectivement. Dans la deuxième partie de notre travail, nous avons exploré les effets directs d'engrais, par rapport à leur activité de l'eau (aw), sur la germination des spores et la pression de turgescence cellulaire. Les spores ont été soumises à trois engrais avec des valeurs de aw différentes et la germination ainsi que la cytorrhyse (effondrement de la paroi cellulaire) des spores ont été évaluées après différents temps d'incubation. Les valeurs de aw des engrais ont été utilisées comme indicateurs de leurs pressions osmotiques. L'exposition des spores de Glomus irregulare au choc osmotique causé par les engrais dont les valeurs de aw se situent entre 0,982 et 0,882 a provoqué des changements graduels au niveau de leur cytorrhyse et de leur germination. Avec l'augmentation de la pression de turgescence externe, la cytorrhyse a augmenté, tandis que le taux de germination a diminué. Ces effets ont été plus prononcés à des concentrations élevées en éléments nutritifs. La présente étude, bien qu’elle constitue une étape importante dans la compréhension des propriétés mécaniques et osmotiques des spores de CMA, confirme également que ces propriétés dépendent probablement de plusieurs facteurs, dont certains qui ne sont pas encore identifiés.

Cell wall composition regulates cell shape and growth behaviour in pollen tubes

L’une des particularités fondamentales caractérisant les cellules végétales des cellules animales est la présence de la paroi cellulaire entourant le protoplaste. La paroi cellulaire joue un rôle primordial dans (1) la protection du protoplaste, (2) est impliquée dans les mécanismes de filtration et (3) est le lieu de maintes réactions biochimiques nécessaires à la régulation du métabolisme et des propriétés mécaniques de la cellule. Les propriétés locales d’élasticité, d’extensibilité, de plasticité et de dureté des composants pariétaux déterminent la géométrie et la forme des cellules lors des processus de différentiation et de morphogenèse. Le but de ma thèse est de comprendre les rôles que jouent les différents composants pariétaux dans le modelage de la géométrie et le contrôle de la croissance des cellules végétales. Pour atteindre cet objectif, le modèle cellulaire sur lequel je me suis basé est le tube pollinique ou gamétophyte mâle. Le tube pollinique est une protubérance cellulaire qui se forme à partir du grain de pollen à la suite de son contact avec le stigmate. Sa fonction est la livraison des cellules spermatiques à l’ovaire pour effectuer la double fécondation. Le tube pollinique est une cellule à croissance apicale, caractérisée par la simple composition de sa paroi et par sa vitesse de croissance qui est la plus rapide du règne végétal. Ces propriétés uniques font du tube pollinique le modèle idéal pour l’étude des effets à courts termes du stress sur la croissance et le métabolisme cellulaire ainsi que sur les propriétés mécaniques de la paroi. La paroi du tube pollinique est composée de trois composantes polysaccharidiques : pectines, cellulose et callose et d’une multitude de protéines. Pour comprendre les effets que jouent ces différents composants dans la régulation de la croissance du tube pollinique, j’ai étudié les effets de mutations, de traitements enzymatiques, de l’hyper-gravité et de la gravité omni-directionnelle sur la paroi du tube pollinique. En utilisant des méthodes de modélisation mathématiques combinées à de la biologie moléculaire et de la microscopie à fluorescence et électronique à haute résolution, j’ai montré que (1) la régulation de la chimie des pectines est primordiale pour le contrôle du taux de croissance et de la forme du tube et que (2) la cellulose détermine le diamètre du tube pollinique en partie sub-apicale. De plus, j’ai examiné le rôle d’un groupe d’enzymes digestives de pectines exprimées durant le développement du tube pollinique : les pectate lyases. J’ai montré que ces enzymes sont requises lors de l’initiation de la germination du pollen. J’ai notamment directement prouvé que les pectate lyases sont sécrétées par le tube pollinique dans le but de faciliter sa pénétration au travers du style.

Mechanical simulation of the endovascular repair of abdominal aortic aneurysms

Ce travail de thèse porte sur la simulation du déploiement des prothèses vasculaires de type stent-graft (SG) lors de la réparation endovasculaire (EVAR) des anévrismes de l’aorte abdominale (AAA). Cette étude se présente en trois parties: (i) tests mécaniques en flexion et compression de SG couramment utilisés (corps et jambage de marque Cook) ainsi que la simulation numérique desdits tests, (ii) développement d’un modèle numérique d’anévrisme, (iii) stratégie de simulation du déploiement des SG. La méthode numérique employée est celle des éléments finis. Dans un premier temps, une vérification du modèle éléments finis (MEF) des SG est realisée par comparaison des différents cas de charge avec leur pendant expérimental. Ensuite, le MEF vasculaire (AAA) est lui aussi vérifié lors d’une comparaison des niveaux de contraintes maximales principales dans la paroi avec des valeurs de la littérature. Enfin, le déploiement est abordé tout en intégrant les cathéters. Les tests mécaniques menés sur les SG ont été simulés avec une différence maximale de 5,93%, tout en tenant compte de la pré-charge des stents. Le MEF de la structure vasculaire a montré des contraintes maximales principales éloignées de 4,41% par rapport à un modèle similaire précédemment publié. Quant à la simulation du déploiement, un jeu complet de SG a pu être déployé avec un bon contrôle de la position relative et globale, dans un AAA spécifique pré-déformé, sans toutefois inclure de thrombus intra-luminal (TIL). La paroi du AAA a été modélisée avec une loi de comportement isotropique hyperélastique. Étant donné que la différence maximale tolérée en milieu clinique entre réalité et simulation est de 5%, notre approche semble acceptable et pourrait donner suite à de futurs développements. Cela dit, le petit nombre de SG testés justifie pleinement une vaste campagne de tests mécaniques et simulations supplémentaires à des fins de validation.