Controle aplicado a poços com método de elevação e bombeio centrífugo submerso

The Electrical Submersible Pumping is an artificial lift method for oil wells employed in onshore and offshore areas. The economic revenue of the petroleum production in a well depends on the oil flow and the availability of lifting equipment. The fewer the failures, the lower the revenue shortfall and costs to repair it. The frequency with which failures occur depends on the operating conditions to which the pumps are submitted. In high-productivity offshore wells monitoring is done by operators with engineering support 24h/day, which is not economically viable for the land areas. In this context, the automation of onshore wells has clear economic advantages. This work proposes a system capable of automatically control the operation of electrical submersible pumps, installed in oil wells, by an adjustment at the electric motor rotation based on signals provided by sensors installed on the surface and subsurface, keeping the pump operating within the recommended range, closest to the well s potential. Techniques are developed to estimate unmeasured variables, enabling the automation of wells that do not have all the required sensors. The automatic adjustment, according to an algorithm that runs on a programmable logic controller maintains the flow and submergence within acceptable parameters avoiding undesirable operating conditions, as the gas interference and high engine temperature, without need to resort to stopping the engine, which would reduce the its useful life. The control strategy described, based on modeling of physical phenomena and operational experience reported in literature, is materialized in terms of a fuzzy controller based on rules, and all generated information can be accompanied by a supervisory system

Efetividade da terapia fisica descongestiva na cicatrização de úlceras venosas

A venous ulcer is the most serious clinical manifestation of chronic venous failure, and the most frequent in lower limbs, accounting for 70% of all ulcers. Patients may suffer from this infirmity for several years without healing of the lesion if treatment is inadequate. The aim of this investigation was to verify the effectiveness of decongestive physical therapy in the healing of venous ulcers. This is a quasi-experimental, interventionist study, with paired, non-probabilistic sampling, composed of 50 patients divided into two groups: control and intervention, each composed of 25 patients. Both groups were identically treated for six months with daily dressings and the latter also underwent complex physical therapy consisting of a combination of the following techniques: manual lymphatic drainage, compression bandaging, lower limb elevation, myolymphokinetic exercises and skin care. The study was approved (Protocol no. 59/2007) by the Ethics Committee of the State University of Southeast Bahia. The Mann-Whitney and Chi-square tests were applied for data analysis. After statistical analysis the patients who underwent therapy showed a statistically significant difference with respect to wound contraction starting in the second month of treatment. Compared to the control, the intervention group showed a greater reduction in both pain and edema starting in the third and fourth month of therapy, respectively. To reinforce these findings, the mean percentage of tissue present at the base of the ulcer (granulation/fibrin ratio) was calculated. The intervention group showed greater granulation at the base of the ulcer compared to the control, significant from the second month of treatment on. It was observed in this study that lymphotherapy, when compared between the intervention and control groups, accelerated the healing process, and reduced pain and edema in the affected limbs. It is expected, therefore, that these results widen scientific knowledge and we suggest that this therapy be used 78 not only to reduce lymphedema, but also as a treatment option for venous ulcers, given its easy application and low cost. The data, therefore, demonstrated the importance of basic care on the part of a multiprofessional and transdisciplinary health team involved in the healing process of these infirmities, thereby contributing to better quality of life in these individuals

Manejo nutricional e digestibilidade no quilotórax canino

O quilotórax corresponde ao acúmulo de fluido linfático em um ou em ambos os espaços pleurais, resultante do extravasamento de linfa do ducto torácico ou de uma de suas divisões principais. Este pode estar associado à ascite quilosa em pacientes com distúrbios linfáticos sistêmicos, como na linfangiectasia, em decorrência de defeitos no transporte linfático-venoso do quilo da cavidade torácica para a circulação sistêmica. A linfangiectasia intestinal é um distúrbio obstrutivo que envolve o sistema linfático do órgão e revela-se como a causa mais comum de enteropatias associadas à má absorção e perda de proteínas em cães. São apresentados no presente relato o controle clínico com o uso de dieta caseira com baixa gordura e a quantificação da função digestiva, por meio da determinação da digestibilidade do alimento, em um cão acometido por quilotórax secundário à linfangiectasia intestinal. A dieta caseira incluiu arroz, peito de frango, cenoura, carbonato de cálcio, levedura de cerveja, suplemento vitamínico e mineral e sal. O ensaio de digestibilidade foi conduzido pelo método de coleta total de fezes. A dieta caseira foi eficaz em interromper o acúmulo de efusão quilosa torácica, restabelecer as concentrações de proteína total e albumina e promover ganho de peso no paciente. Os resultados da digestibilidade demonstraram menor aproveitamento de todos os nutrientes no cão com linfangiectasia em relação ao controle sadio.

Correlação da atividade de lactato desidrogenase e concentração de lactato com a classificação de efusões em cães

As efusões são problemas clínicos frequentes e que ocorrem em consequência de uma enfermidade que culmine com diminuição da pressão coloidosmótica intravascular, elevação da pressão hidrostática local, aumento da permeabilidade vascular e/ou comprometimento da drenagem realizada pelos vasos linfáticos. Dessa maneira, a avaliação laboratorial desse fluido torna-se relevante para que, em conjunto com os sinais clínicos apresentados pelo paciente, possa ser firmado um possível diagnóstico e instituída ação terapêutica adequada. Assim sendo, a classificação de uma efusão em transudato ou exsudato torna-se um dos pontos críticos para a elucidação do diagnóstico e condução do caso clínico. em Medicina Veterinária, o método tradicional de classificação de uma efusão é baseado na contagem celular e na concentração de proteínas do fluido. Contudo, diversos estudos evidenciam que tais parâmetros não são suficientes para a correta classificação de todas as efusões. Assim, o presente estudo foi conduzido com o objetivo de verificar a correlação de outros parâmetros bioquímicos com a diferenciação das efusões transudativas e exsudativas e, para tal, foram avaliadas as atividades de lacatato desidrogenase (LDH) das efusões, a relação de sua atividade fluido/soro, concentração de lactato das efusões, o gradiente de concentração de lactato do soro para o fluido e a concentração de proteínas das efusões. Os resultados obtidos permitiram observar que a atividade de LDH, a relação LDH efusão/soro, a concentração de lactato e o gradiente de concentração de lactato soro/efusão apresentam diferença estatisticamente significativa (P<0,05), bem como alta correlação com a classificação de uma efusão exsudativa.

Respostas funcionais de diferentes tamanhos de Tilápia do Nilo; Oreochromis niloticus; predando zooplâncton

The Nile tilapia, Oreochromis niloticus, is an important omnivorous fish in the reservoirs of the semi-arid region of Brazil. Throughout its growth tilapia s feeding behavior changes from a visual predator of zooplankton to a filter-feeder, collecting suspended particulate matter, including planktonic organisms, through pumping. This feature results in different impacts of tilapia on plankton community as the fish grows. Aiming to quantify the functional response of different sizes of Nile tilapia on zooplankton experiments in microcosms scale in the laboratory and in mesocosm scale in the field were carried out. The data were fitted to four different models of functional response. The best fits were obtained for nonlinear models in laboratory experiments. While the experiments in mesocosms were the best settings for responses of type I (juvenile and adult tilapia) and type III (fry). The Manly's alpha index was used to evaluate the feeding selectivity of tilapia on the three main groups of the zooplankton in the experiments in mesocosms. The results show that: (i) rotifers were the preferred prey of fingerlings,(ii) copepods were rejected by fry and juvenile tilapia and (iii) adult fish fed non-selectively on copepods, cladocerans and rotifers. The functional response models obtained in this research can be applied to population models and help in modeling the dynamics of interactions between Nile tilapia and the planktonic communities in the reservoirs of the semi-arid

Avaliação de tanques de escorva utilizados em substituição à válvula-de-pé em instalações de bombeamento

A maioria das instalações de abastecimento de água utiliza bombas hidráulicas do tipo turbobombas, requerendo que o interior de sua carcaça e da tubulação de sucção esteja preenchido com água (escorvados) para que a sucção da água possa ser efetivada. O escorvamento das bombas pode ser efetuado instalando-as abaixo do reservatório de captação (bomba afogada). Quando a bomba está acima do reservatório e o escorvamento é manual, é necessário usar válvulas-de-pé, que são suscetíveis ao mau funcionamento, limitando a confiabilidade do sistema, principalmente em caso de automação. Como alternativa à válvula-de-pé, neste trabalho, foram estudados dois tanques escorva, testados no Laboratório de Hidráulica e Irrigação da FCAV/UNESP - Jaboticabal, avaliando-se situações de altura manométrica de sucção de bomba centrífuga e relações entre volume útil do tanque e volume do tubo de sucção, tendo-se concluído: a) o volume do tanque de escorva é função do volume do tubo de sucção da instalação de bombeamento e da altura manométrica de sucção; b) o volume do tanque de escorva pode ser calculado seguindo-se a Lei de Boyle, com percentagem de acréscimo que, neste estudo, foi de 10% para um modelo de tanque e de 30% para o segundo modelo.

Estudo de estratégias de otimização para poços de petróleo com elevação por bombeio de cavidades progressivas

The progressing cavity pump artificial lift system, PCP, is a main lift system used in oil production industry. As this artificial lift application grows the knowledge of it s dynamics behavior, the application of automatic control and the developing of equipment selection design specialist systems are more useful. This work presents tools for dynamic analysis, control technics and a specialist system for selecting lift equipments for this artificial lift technology. The PCP artificial lift system consists of a progressing cavity pump installed downhole in the production tubing edge. The pump consists of two parts, a stator and a rotor, and is set in motion by the rotation of the rotor transmitted through a rod string installed in the tubing. The surface equipment generates and transmits the rotation to the rod string. First, is presented the developing of a complete mathematical dynamic model of PCP system. This model is simplified for use in several conditions, including steady state for sizing PCP equipments, like pump, rod string and drive head. This model is used to implement a computer simulator able to help in system analysis and to operates as a well with a controller and allows testing and developing of control algorithms. The next developing applies control technics to PCP system to optimize pumping velocity to achieve productivity and durability of downhole components. The mathematical model is linearized to apply conventional control technics including observability and controllability of the system and develop design rules for PI controller. Stability conditions are stated for operation point of the system. A fuzzy rule-based control system are developed from a PI controller using a inference machine based on Mandami operators. The fuzzy logic is applied to develop a specialist system that selects PCP equipments too. The developed technics to simulate and the linearized model was used in an actual well where a control system is installed. This control system consists of a pump intake pressure sensor, an industrial controller and a variable speed drive. The PI control was applied and fuzzy controller was applied to optimize simulated and actual well operation and the results was compared. The simulated and actual open loop response was compared to validate simulation. A case study was accomplished to validate equipment selection specialist system

Ajuste automático e otimização do tempo de espera (Idle time) em bombeio mecânico de petróleo

The present work presents an algorithm proposal, which aims for controlling and improving idle time to be applied in oil production wells equipped with beam pump. The algorithm was totally designed based on existing papers and data acquired from two Potiguar Basin pilot wells. Oil engineering concepts such as submergence, pump off, Basic Sediments and Water (BSW), Inflow Performance Relationship (IPR), reservo ir pressure, inflow pressure, among others, were included into the algorithm through a mathematical treatment developed from a typical well and then extended to the general cases. The optimization will increase the well production potential maximum utilization having the smallest number of pumping unit cycles directly reflecting on operational cost and electricity consumption reduction

Implantação de um sistema de detecção de vazamentos em oleodutos com tratamento de alarmes falsos

The pumping of fluids in pipelines is the most economic and safe form of transporting fluids. That explains why in Europe there was in 1999 about 30.000 Km [7] of pipelines of several diameters, transporting millíons of cubic meters of crude oil end refined products, belonging to COCAWE (assaciation of companies of petroleum of Europe for health, environment and safety, that joint several petroleum companies). In Brazil they are about 18.000 Km of pipelines transporting millions of cubic meters of liquids and gases. In 1999, nine accidents were registered to COCAWE. Among those accidents one brought a fatal victim. The oil loss was of 171 m3, equivalent to O,2 parts per million of the total of the transported volume. Same considering the facts mentioned the costs involved in ao accident can be high. An accident of great proportions can bríng loss of human lives, severe environmental darnages, loss of drained product, loss . for dismissed profit and damages to the image of the company high recovery cost. In consonance with that and in some cases for legal demands, the companies are, more and more, investing in systems of Leak detection in pipelines based on computer algorithm that operate in real time, seeking wíth that to minimize still more the drained volumes. This decreases the impacts at the environment and the costs. In general way, all the systems based on softWare present some type of false alarm. In general a commitment exists betWeen the sensibílity of the system and the number of false alarms. This work has as objective make a review of thé existent methods and to concentrate in the analysis of a specific system, that is, the system based on hydraulic noise, Pressure Point Analyzis (PPA). We will show which are the most important aspects that must be considered in the implementation of a Leak Detection System (LDS), from the initial phase of the analysis of risks passing by the project bases, design, choice of the necessary field instrumentation to several LDS, implementation and tests. We Will make na analysis of events (noises) originating from the flow system that can be generator of false alarms and we will present a computer algorithm that restricts those noises automatically

Detecção e classificação de modos de operação do bombeio mecânico via cartas dinamométricas

The precision and the fast identification of abnormalities of bottom hole are essential to prevent damage and increase production in the oil industry. This work presents a study about a new automatic approach to the detection and the classification of operation mode in the Sucker-rod Pumping through dynamometric cards of bottom hole. The main idea is the recognition of the well production status through the image processing of the bottom s hole dynamometric card (Boundary Descriptors) and statistics and similarity mathematics tools, like Fourier Descriptor, Principal Components Analysis (PCA) and Euclidean Distance. In order to validate the proposal, the Sucker-Rod Pumping system real data are used

Remoção mecânica de plantas aquáticas: análise econômica e operacional

A remoção de plantas aquáticas tem sido utilizada como opção ao controle químico e biológico, em razão de restrições ambientais em algumas regiões brasileiras. O objetivo deste trabalho foi desenvolver um modelo para análise econômica e operacional da remoção mecânica de plantas aquáticas, visando realizar estudo econômico comparativo com o controle químico. A operação foi estudada num reservatório de uma usina de bombeamento em Barra do Piraí-RJ. O sistema consiste de retroescavadeiras instaladas em balsas, usadas para cortar as plantas e liberá-las no fluxo de água. Antes da tomada d'água existe uma barreira flutuante que intercepta as plantas, as quais são removidas por um guindaste fixo nas margens. As plantas são armazenadas por algum tempo e depois descartadas. Existe, ainda, um sistema de limpeza das grades da tomada d'água. Dados do volume total de plantas descartadas foram coletados durante 14 meses, assim como foi avaliado o volume de biomassa produzido por área das principais espécies infestantes. A empreiteira que administra o serviço forneceu planilhas de custos e outro parâmetros operacionais. Um modelo foi desenvolvido para calcular custos por hectare de plantas removidas. Os resultados mostraram custo médio mensal de US$ 17.780,28 por hectare. Apesar do alto custo, o sistema de remoção demonstrou capacidade de controlar apenas 4,1% da área infestada no reservatório, na época da coleta dos dados. Simulando dados de uma aplicação de glyphosate, o controle químico custaria apenas 0,23% do custo da remoção. Análises de sensibilidade mostraram que a compactação das plantas para transporte, o volume de plantas produzidas por área e o custo do transporte são os parâmetros principais para a otimização.

Desenvolvimento de um simulador de bombeio por cavidades progressivas

The method of artificial lift of progressing cavity pump is very efficient in the production of oils with high viscosity and oils that carry a great amount of sand. This characteristic converted this lift method into the second most useful one in oil fields production. As it grows the number of its applications it also increases the necessity to dominate its work in a way to define it the best operational set point. To contribute to the knowledge of the operational method of artificial lift of progressing cavity pump, this work intends to develop a computational simulator for oil wells equipped with an artificial lift system. The computational simulator of the system will be able to represent its dynamic behavior when submitted to the various operational conditions. The system was divided into five subsystems: induction motor, multiphase flows into production tubing, rod string, progressing cavity pump and annular tubing-casing. The modeling and simulation of each subsystem permitted to evaluate the dynamic characteristics that defined the criteria connections. With the connections of the subsystems it was possible to obtain the dynamic characteristics of the most important arrays belonging to the system, such as: pressure discharge, pressure intake, pumping rate, rod string rotation and torque applied to polish string. The shown results added to a friendly graphical interface converted the PCP simulator in a great potential tool with a didactic characteristic in serving the technical capability for the system operators and also permitting the production engineering to achieve a more detail analysis of the dynamic operational oil wells equipped with the progressing cavity pump

Simulador computacional para poços de petróleo com método de elevação artificial por bombeio mecânico

This work proposes a computer simulator for sucker rod pumped vertical wells. The simulator is able to represent the dynamic behavior of the systems and the computation of several important parameters, allowing the easy visualization of several pertinent phenomena. The use of the simulator allows the execution of several tests at lower costs and shorter times, than real wells experiments. The simulation uses a model based on the dynamic behavior of the rod string. This dynamic model is represented by a second order partial differencial equation. Through this model, several common field situations can be verified. Moreover, the simulation includes 3D animations, facilitating the physical understanding of the process, due to a better visual interpretation of the phenomena. Another important characteristic is the emulation of the main sensors used in sucker rod pumping automation. The emulation of the sensors is implemented through a microcontrolled interface between the simulator and the industrial controllers. By means of this interface, the controllers interpret the simulator as a real well. A "fault module" was included in the simulator. This module incorporates the six more important faults found in sucker rod pumping. Therefore, the analysis and verification of these problems through the simulator, allows the user to identify such situations that otherwise could be observed only in the field. The simulation of these faults receives a different treatment due to the different boundary conditions imposed to the numeric solution of the problem. Possible applications of the simulator are: the design and analysis of wells, training of technicians and engineers, execution of tests in controllers and supervisory systems, and validation of control algorithms

Modelo matemático para otimização dos custos de um sistema híbrido eólico-solar : aplicação no bombeamento de petróleo

This work purposes the application of a methodology to optimize the implantation cost of an wind-solar hybrid system for oil pumping. The developed model is estimated the implantation cost of system through Multiple Linear Regression technique, on the basis of the previous knowledge of variables: necessary capacity of storage, total daily energy demand, wind power, module power and module number. These variables are gotten by means of sizing. The considered model not only can be applied to the oil pumping, but also for any other purposes of electric energy generation for conversion of solar, wind or solar-wind energy, that demand short powers. Parametric statistical T-student tests had been used to detect the significant difference in the average of total cost to being considered the diameter of the wind, F by Snedecor in the variance analysis to test if the coefficients of the considered model are significantly different of zero and test not-parametric statistical by Friedman, toverify if there is difference in the system cost, by being considered the photovoltaic module powers. In decision of hypothesis tests was considered a 5%-significant level. The configurations module powers showed significant differences in total cost of investment by considering an electrical motor of 3 HP. The configurations module powers showed significant differences in total cost of investment by considering an electrical motor of 5 HP only to wind speed of 4m/s and 6 m/s in wind of 3 m, 4m and 5 m of diameter. There was not significant difference in costs to diameters of winds of 3 m and 4m. The mathematical model and the computational program may be used to others applications which require electrical between 2.250 W and 3.750 W. A computational program was developed to assist the study of several configurations that optimizes the implantation cost of an wind-solar system through considered mathematical model

Simulação computacional da interação fluido-estrutura em bombas de cavidades progressivas

The pumping through progressing cavities system has been more and more employed in the petroleum industry. This occurs because of its capacity of elevation of highly viscous oils or fluids with great concentration of sand or other solid particles. A Progressing Cavity Pump (PCP) consists, basically, of a rotor - a metallic device similar to an eccentric screw, and a stator - a steel tube internally covered by a double helix, which may be rigid or deformable/elastomeric. In general, it is submitted to a combination of well pressure with the pressure generated by the pumping process itself. In elastomeric PCPs, this combined effort compresses the stator and generates, or enlarges, the clearance existing between the rotor and the stator, thus reducing the closing effect between their cavities. Such opening of the sealing region produces what is known as fluid slip or slippage, reducing the efficiency of the PCP pumping system. Therefore, this research aims to develop a transient three-dimensional computational model that, based on single-lobe PCP kinematics, is able to simulate the fluid-structure interaction that occurs in the interior of metallic and elastomeric PCPs. The main goal is to evaluate the dynamic characteristics of PCP s efficiency based on detailed and instantaneous information of velocity, pressure and deformation fields in their interior. To reach these goals (development and use of the model), it was also necessary the development of a methodology for generation of dynamic, mobile and deformable, computational meshes representing fluid and structural regions of a PCP. This additional intermediary step has been characterized as the biggest challenge for the elaboration and running of the computational model due to the complex kinematic and critical geometry of this type of pump (different helix angles between rotor and stator as well as large length scale aspect ratios). The processes of dynamic generation of meshes and of simultaneous evaluation of the deformations suffered by the elastomer are fulfilled through subroutines written in Fortan 90 language that dynamically interact with the CFX/ANSYS fluid dynamic software. Since a structural elastic linear model is employed to evaluate elastomer deformations, it is not necessary to use any CAE package for structural analysis. However, an initial proposal for dynamic simulation using hyperelastic models through ANSYS software is also presented in this research. Validation of the results produced with the present methodology (mesh generation, flow simulation in metallic PCPs and simulation of fluid-structure interaction in elastomeric PCPs) is obtained through comparison with experimental results reported by the literature. It is expected that the development and application of such a computational model may provide better details of the dynamics of the flow within metallic and elastomeric PCPs, so that better control systems may be implemented in the artificial elevation area by PCP