Synthesis, characterization and benzylation activity of nanocrystalline chromia loaded sulfated titania prepared via sol–gel route

Chromia loaded sulfated titania has been synthesized via sol–gel route with different chromia loadings. These catalysts are characterized using conventional techniques such as XRD analysis, FTIR analysis, surface area and pore volume measurements, EDX, SEM and UV–Vis diffuse reflectance spectral analysis. Acidity is measured using spectrophotometric monitoring of adsorption of perylene, thermogravimetric desorption of 2,6-dimethylpyridine and temperature programmed desorption of ammonia. Activity studies are done in the liquid phase. It has been concluded that Lewis acid sites are responsible for the benzylation of arenes with benzyl chloride.

Synthesis, characterization and catalytic activity of Nd203 supported V205 catalysts

A series of rare-earth neodymia supported vanadium oxide catalysts with various V205 loadings ranging from 3 to 15 wt.% were prepared by the wet impregnation method using ammonium metavanadate as the vanadium precursor. The nature of vanadia species formed on the support surface is characterized hy a series of different physicochemical techniques like X-ray diffraction (XRD). Fourier transform infrared spectroscopy (FTIR). BET surface area, diffuse reflectance UV-vis spectroscopy (DR UV-vis), thermal analysis (TG-DTG/DTA) and SEM. The acidity of the prepared systems were verified by the stepwise temperature programmed desorprion of ammonia (NH3-TPD) and found that the total acidity gets increased with the percentage of vanadia loading. XRD and FT1R results shows the presence of surface dispersed vanadyl species at lower loadings and the formation of higher vanadate species as the percentage composition of vanadia is increased above 9 wt.%. The low surface area of the support. calcination temperature and the percentage of vanadia loading are found to influence the formation of higher vanadia species. The catalytic activity of the V205-Nd203 catalysts was probed in the liquid phase hydroxylation of phenol and the result show that the present catalysts are active at lower vanadia concentrations.

Overtone Spectra of 1,2-Dichloro-And Dibromo-Ethanes in the Near Infrared Region

The vibrational overtone spectra 0f the liquid phase 1,2-dichloroethane and 1,2-dibromoethane in the spectral regions of CH stretching local mode overtones corresponding to delta v CH= = 2 to delta v CH=5 are reported. The observed spectral features are assigned using the local mode model. LocaI mode frequencies WCH and diagonal local mode anharmonicities XCH are obtained from an analysis of the spectra. The local-local combinations observed are interpreted on the basis of a coupled CH oscillator model hamiltonian. Local-normal combinations show complex structures and their possible assignments are given.

Studies on Catalysis by Titania

Scientists throughout the world are in search of a better methodology to reduce the use of environmentally hazardous chemicals common in industries .A significant contribution in this field is given by different redox catalysts in oxidation reactions. The oxidation of organic substrates represents one of the most important industrial chemical reactions, explaining the significant efforts invested in the research and development of new heterogeneous catalysts with increased activities and selectivities in these type reactions[l-4|. Hence liquid phase reactions like epoxidation of cylcohexene and hydroxylation of phenol were carried out with a new outlook in the challenge using CeO2/TiO;; and CuO/TiO2 catalysts denoted as TiO2-Ce as TiO2-Cu respectively in this work. Also different wt% of metals incorporated titania catalysts like 3, 6, 9 wt% CeO2/TiO; and CuO/TiO;were subjected to the present study .The interaction between metal oxides and the oxide supports have attracted much attention because of the wide applications of supported metal oxide systems[7,8]. It is well known that supported oxides of transition metals are widely used as catalysts for various reactions. Titania as well its metal modified catalysts systems afford high activity and selectivity in the liquid phase epoxidation of cyclohexene[9]. Cyclohexene epoxide is obtained as the major product during the reaction with small amounts of allylic substitution products.This chapter gives an idea about the liquid phase oxidation reactions like epoxidation of cylcohexene and hydroxylation of phenol in which many industrially important products are formed. Here discusses about the redox properties of the ceria and copper incorporated titania catalysts.The epoxidation of cyclohcxene is carried out efficiently over the prepared systems with the selective formation of cyclohexane epoxide. This reaction hints that it might be possible to create cleaner nylon chemistry. The total acidity of the prepared systems plays an important role in determining the catalytic activity in the dehydrogenation of cyclohexane and cyclohexene. The total acidity of the prepared systems plays an important role in determining the catalytic activity in the dehydrogenation of cyclohexane and cyclohexene.

Laser induced thermal lens and near infrared absorption studies of ch overtones in some organic compounds

Vibrational overtone spectroscopy of X-H (X=C,N,O) containing molecules is an area of recent interest. The spectroscopic studies of higher vibrational levels yield valuable informations, regarding,the molecular structure, intra- and inter-molecular interactions, radiationless transitions, intra-molecular vibrational relaxations, multiphoton excitations and chemical reactivities, which cannot be z obtained by other spectroscopic methods. This thesis presents the results of experimental investigations on the overtone spectra of some organic compounds in the liquid phase for the characterization of CH bonds. The spectra in the fifth overtone region (1fiV=6) are recorded using a dual beam thermal lens setup and the lower overtones (.AV=2-5) are recorded spectrophotometrically.The thesis is presented in six chapters.

NIR Spectroscopic and Laser Induced Fluorescence studies of some organic molecules

Vibrational overtone spectroscopy of molecules containing X-H oscillators (X = C, N, O...) has become an effective tool for the study of molecular structure, dynamics, inter and intramolecular interactions, conformational aspects and substituent effects in aliphatic and aromatic compounds. In the present work, the author studied the NIR overtone spectra of some liquid phase organic compounds. The analysis of the CH, NH and OH overtones yielded important structural information about these systems. In an attempt to get information on electronic energy levels, we studied the pulsed Nd:YAG laser induced fluorescence spectra of certain organic compounds. The pulsed laser Raman spectra of some organic compounds are also studied. The novel high resolution technique of near infrared tunable diode laser absorption spectroscopy (TDLAS) is used to record the rotational structure of the second OH overtone spectrum of 2-propanol. The spectral features corresponding to the different molecular conformations could be identified from the high resolution spectrum. The whole work described in this thesis is divided into five chapters.

GaInAsP-basierende Resonatorstrukturen

Physikalische Grundlagenforschung und anwendungsorientierte physikalische Forschung auf den Gebieten nanoskaliger kristalliner und amorpher fester Körper haben in vielfacher Weise eine große Bedeutung. Neben dem Verständnis für die Struktur der Materie und die Wechselwirkung von Objekten von der Größe einiger Atome ist die Erkenntnis über die physikalischen Eigenschaften nanostrukturierter Systeme von hohem Interesse. Diese Forschung eröffnet die Möglichkeit, die mit der Mikroelektronik begonnene Miniaturisierung fortzusetzen und wird darüber hinaus neue Anwendungsfelder eröffnen. Das Erarbeiten der physikalischen Grundlagen der Methoden zur Herstellung und Strukturierung ist dabei zwingend notwendig, da hier Wirkungsprinzipien dominieren, die erst bei Strukturgrößen im Nanometerbereich auftreten oder hinreichend stark ausgeprägt sind. Insbesondere Halbleitermaterialien sind hier von großem Interesse. Die in dieser Arbeit untersuchten Resonatorstrukturen, die auf dem kristallinen Verbindungshalbleitermaterial GaInAsP/InP basieren, erschließen wichtige Anwendungsfelder im Bereich der optischen Datenübertragung sowie der optischen Sensorik. Hergestellt wird das Halbleitermaterial mit der Metallorganischen Gasphasenepitaxie. Die experimentell besimmten Kenngrößen lassen Rückschlüsse auf die Güte der Materialien, die quantenmechanischen Wirkungsprinzipien und die Bauelementcharakteristik zu und führen zu optimal angepassten Kristallstrukturen. Auf Basis dieser optimierten Materialien wurde ein durchstimmbarer Fabry-Perot-Filter hergestellt, der aus einer Kombination aus InP-Membranen und Luftspalten besteht und elektromechanisch aktuiert werden kann. Das GaInAsP dient hierbei als wenige hundert nm dicke Opferschicht, die ätztechnisch hochselektiv beseitigt wird. Die Qualität der Grenzflächen zum InP ist entscheidend für die Qualität der freigeätzten Kavitäten und damit für die mechanische Gesamtstabilität der Struktur. Der in dieser Arbeit beschriebene Filter hat eine Zentralwellenlänge im Bereich von 1550 nm und weist einen Durchstimmbereich von 221 nm auf. Erzielt wurde dieser Wert durch ein konsistentes Modell der wirkenden Verspannungskomponenten und einer optimierten epitaktischen Kontrolle der Verspannungsparameter. Das realisierte Filterbauelement ist vielversprechend für den Einsatz in der optischen Kommunikation im Bereich von WDM (wavelength division multiplexing) Anwendungen. Als weitere Resonatorstrukur wurde ein Asymmetrisch gekoppelter Quantenfilm als optisch aktives Medium, bestehend aus GaInAsP mit variierender Materialkomposition und Verspannung, untersucht, um sein Potential für eine breitbandige Emission zu untersuchen und mit bekannten Modellen zu vergleichen. Als Bauelementdesign wurde eine kantenemittierende Superlumineszenzleuchtdiode gewählt. Das Ergebnis ist eine Emissionskurve von 100 nm, die eine höhere Unabhängigkeit vom Injektionsstrom aufweist als andere bekannte Konzepte. Die quantenmechanischen Wirkungsprinzipien - im wesentlichen die Kopplung der beiden asymmetrischen Potentialtöpfe und die damit verbundene Kopplung der Wellenfunktionen - werden qualitativ diskutiert. Insgesamt bestätigt sich die Eignung des Materials GaInAsP auch für neuartige, qualitativ höchst anspruchsvolle Resonatorstrukturen und die Bedeutung der vorgestellten und untersuchten Resonatorkonzepte. Die vorgestellten Methoden, Materialien und Bauelemente liefern aufgrund ihrer Konzeption und der eingehenden experimentellen Untersuchungen einen Beitrag sowohl zu den zugrunde liegenden mechanischen, optoelektronischen und quantenmechanischen Wirkungsprinzipien der Strukturen, als auch zur Realisierung neuer optoelektronischer Bauelemente.

Atomistic-continuum modeling of ultrafast laser-induced melting of silicon targets

In this work, we present an atomistic-continuum model for simulations of ultrafast laser-induced melting processes in semiconductors on the example of silicon. The kinetics of transient non-equilibrium phase transition mechanisms is addressed with MD method on the atomic level, whereas the laser light absorption, strong generated electron-phonon nonequilibrium, fast heat conduction, and photo-excited free carrier diffusion are accounted for with a continuum TTM-like model (called nTTM). First, we independently consider the applications of nTTM and MD for the description of silicon, and then construct the combined MD-nTTM model. Its development and thorough testing is followed by a comprehensive computational study of fast nonequilibrium processes induced in silicon by an ultrashort laser irradiation. The new model allowed to investigate the effect of laser-induced pressure and temperature of the lattice on the melting kinetics. Two competing melting mechanisms, heterogeneous and homogeneous, were identified in our big-scale simulations. Apart from the classical heterogeneous melting mechanism, the nucleation of the liquid phase homogeneously inside the material significantly contributes to the melting process. The simulations showed, that due to the open diamond structure of the crystal, the laser-generated internal compressive stresses reduce the crystal stability against the homogeneous melting. Consequently, the latter can take a massive character within several picoseconds upon the laser heating. Due to the large negative volume of melting of silicon, the material contracts upon the phase transition, relaxes the compressive stresses, and the subsequent melting proceeds heterogeneously until the excess of thermal energy is consumed. A series of simulations for a range of absorbed fluences allowed us to find the threshold fluence value at which homogeneous liquid nucleation starts contributing to the classical heterogeneous propagation of the solid-liquid interface. A series of simulations for a range of the material thicknesses showed that the sample width we chosen in our simulations (800 nm) corresponds to a thick sample. Additionally, in order to support the main conclusions, the results were verified for a different interatomic potential. Possible improvements of the model to account for nonthermal effects are discussed and certain restrictions on the suitable interatomic potentials are found. As a first step towards the inclusion of these effects into MD-nTTM, we performed nanometer-scale MD simulations with a new interatomic potential, designed to reproduce ab initio calculations at the laser-induced electronic temperature of 18946 K. The simulations demonstrated that, similarly to thermal melting, nonthermal phase transition occurs through nucleation. A series of simulations showed that higher (lower) initial pressure reinforces (hinders) the creation and the growth of nonthermal liquid nuclei. For the example of Si, the laser melting kinetics of semiconductors was found to be noticeably different from that of metals with a face-centered cubic crystal structure. The results of this study, therefore, have important implications for interpretation of experimental data on the kinetics of melting process of semiconductors.

Adsorbents a partir de fangs biològics excedents de depuradora mitjançant l'aplicació de microones: estudi d'obtenció, caracterització i aplicació en fase líquida

El fang biològic es produeix en les plantes de tractament d'aigües residuals urbanes i industrials. El tractament i la gestió dels fangs és un dels problemes més importants en el camp del tractament de les aigües residuals. Aquesta situació es preveu que es veurà agreujada en el futur, per un increment del volum de fang produït associat a l'exigència de nivells més alts de depuració i per l'augment dels nombre d'estacions depuradores en funcionament. D'altre banda, les limitacions que presenten les opcions tradicionals de gestió dels fangs, fa necessari buscar solucions innovadores i efectives per a solucionar el problema que suposa la gestió d'aquests fangs biològics. Els fangs biològics són de naturalesa carbonosa i amb un alt contingut de matèria orgànica. Aquestes característiques, permeten la conversió del fang en un sòlid adsorbent de tipus carbonós. Aquesta conversió ofereix el doble benefici de reduir el volum de fang que ha de ser gestionat i alhora produir un adsorbent amb un cost inferior a la dels adsorbents convencionals (carbons actius comercials). Fins el moment, els tractaments alta temperatura han demostrat la seva efectivitat per du a terme el procés de transformació dels excedents de fang biològic en un sòlid adsorbent carbonós (carbó actiu). Com a alternativa a aquests processos a alta temperatura, es proposa un nou procés d'obtenció d'un sòlid adsorbent carbonós a partir dels excedents de fangs biològics, mitjançant un tractament a baixa temperatura, combinant el tractament per microones amb l'addició d'un reactiu químic (H2SO4). La present tesi analitza el tractament dels excedents de fangs biològics utilitzant un tractament mitjançant microones i l'addició d'àcid sulfúric (H2SO4), al mateix temps analitza la possibilitat d'utilitzar els sòlids adsorbents obtinguts per a millorar la qualitat de les aigües residuals. Paràmetres d'operació com poden ser la quantitat d'àcid sulfúric addicionada al fang, el nivell de potència del forn microones i el temps de tractament, es modificaran per tal de determinar la influència que poden tenir sobre la qualitat del sòlid adsorbent. Un cop determinada la qualitat dels diferent sòlids adsorbents s'avalua la seva capacitat per a l'eliminació de colorant i metalls en fase líquida. Els resultats obtinguts es comparen amb els obtinguts per un carbó actiu derivat de fangs i un carbó actiu comercial.

Katalizatory złotowo-miedziowe na nośnikach cerowych, cyrkonowych i cerowo-cyrkonowych – preparatyka, charakterystyka i zastosowanie w procesach utleniania

Wydział Chemii

Zinc sorption in selected soils

The adsorption of nutrient elements is one of the most important solid- and liquid-phase interactions determining the retention and release of applied plant nutrients and the efficiency of fertilization. The study showed that the soils with high cation exchange capacity (CEC), CaCO3 , organic matter contents, and heavy texture adsorbed more zinc (Zn). The alkaline soils from Pakistan adsorbed more Zn than English acidic soils. Langmuir and Freundlich isotherm fit was excellent, and r(2) values for the Langmuir isotherm were highly significant (r(2) =0.84 to 0.99). The Langmuir b values, representing the adsorptive capacity of a soil, increased as the texture fineness increased in the soil, with increases in the concentration of adsorptive material (such as organic matter and CaCO3) and with increases in CEC and pH. The alkaline soils from Pakistan had higher bonding energy constant and higher log Kf values than the acidic English soils. Sequential extraction of Zn in these soils showed that most of the Zn was held in CaCO3 pool in the alkaline soils, whereas in acidic soils adsorbed Zn was in exchangeable form.

Designing Temperature-Responsive Biocompatible Copolymers and Hydrogels Based on 2-Hydroxyethyl(meth)acrylates

Free-radical copolymerization of 2-hydroxyethyl methacrylate with 2-hydroxyethyl acrylate can be successively utilized for the synthesis of water-soluble polymers and hydrogels with excellent physicochemical properties, thus showing promise for pharmaceutical and biomedical applications. In the work presented it has been demonstrated that water-soluble copolymers based on 2-hydroxyethyl methacrylate and 2-hydroxyethyl acrylate exhibit lower critical solution temperature in aqueous solutions, whereas the corresponding high molecular weight homopolymers do not have this unique property. The temperature-induced transitions observed upon heating the aqueous solutions of these copolymers proceed via liquid−liquid phase separation. The hydrogels were also synthesized by copolymerizing 2-hydroxyethyl methacrylate and 2-hydroxyethyl acrylate in the absence of a bifunctional cross-linker. The cross-linking of these copolymers during copolymerization is believed to be due to the presence of bifunctional admixtures or transesterification reactions. Transparency, swelling behavior, mechanical properties, and porosity of the hydrogels are dependent upon the monomer ratio in the copolymers. Hydrogel samples containing more 2-hydroxyethyl methacrylate are less transparent, have lower swelling capacity, higher elastic moduli, and pores of smaller size. The assessment of the biocompatibility of the copolymers using the slug mucosal irritation test revealed that they are also less irritant than poly(acrylic acid).

Utilisation by ruminants of nitrogen compounds in silage-based diets

This paper considers the various complex changes that occur to nitrogen (N) containing compounds in forages through the processes of ensiling, rumen degradation and microbial synthesis, post-ruminal digestion and absorption and synthesis into milk protein. Particular emphasis is placed on reviewing recent data on the efficiency of utilisation of N-containing compounds in silages by rumen microbes, since low efficiency here is believed to be a major cause of large N losses to the environment on some silage-based diets. Data are reviewed which show that although rumen degradation of N compounds in silage is rapid and extensive, up to 10% of the soluble N can escape the rumen by being associated with the liquid phase. There is now firm evidence that the composition of the amino acids (AAs) absorbed is heavily dependent on the process of ensiling and that witting or use of certain silage additives conserve the initial amino acid profile of the forage. This provides an opportunity to manipulate the amino acid supply to better match demand thus potentially enhancing utilisation. This review confirms that utilisation of the N fractions in grass and legume silages in particular, is poor and the efficiency of microbial protein synthesis (EMPS) is consistently higher on maize silage-based diets. It is concluded that the way in which grass and legume silages in particular are produced and used in the future needs a radical rethink. New research needs to be aimed at enhancing the utilisation of N in the rumen through a better understanding of N/carbohydrate relationships and the ability of forages to supply degraded carbohydrate. Also more emphasis is needed on understanding of the potentially different role of the different N fractions that exist in silages. (C) 2004 Elsevier B.V. All rights reserved.

A functional proteomic method for the enrichment of peripheral membrane proteins reveals the collagen binding protein Hsp47 is exposed on the surface of activated human platelets

Platelets are small blood cells vital for hemostasis. Following vascular damage, platelets adhere to collagens and activate, forming a thrombus that plugs the wound and prevents blood loss. Stimulation of the platelet collagen receptor glycoprotein VI (GPVI) allows recruitment of proteins to receptor-proximal signaling complexes on the inner-leaflet of the plasma membrane. These proteins are often present at low concentrations; therefore, signaling-complex characterization using mass spectrometry is limited due to high sample complexity. We describe a method that facilitates detection of signaling proteins concentrated on membranes. Peripheral membrane proteins (reversibly associated with membranes) were eluted from human platelets with alkaline sodium carbonate. Liquid-phase isoelectric focusing and gel electrophoresis were used to identify proteins that changed in levels on membranes from GPVI-stimulated platelets. Immunoblot analysis verified protein recruitment to platelet membranes and subsequent protein phosphorylation was preserved. Hsp47, a collagen binding protein, was among the proteins identified and found to be exposed on the surface of GPVI-activated platelets. Inhibition of Hsp47 abolished platelet aggregation in response to collagen, while only partially reducing aggregation in response to other platelet agonists. We propose that Hsp47 may therefore play a role in hemostasis and thrombosis.

Proteomic analysis of resting and thrombin-stimulated platelets reveals the translocation and functional relevance of HIP-55 in platelets

The platelet surface is a dynamic interface that changes rapidly in response to stimuli to coordinate the formation of thrombi at sites of vascular injury. Tight control is essential as loss of organisation may result in the inappropriate formation of thrombi (thrombosis) or excessive bleeding. In this paper we describe the comparative analysis of resting and thrombin-stimulated platelet membrane proteomes and associated proteins to identify proteins important to platelet function. Surface proteins were labelled using a biotin tag and isolated by NeurtrAvidin affinity chromatography. Liquid phase IEF and SDS-PAGE were used to separate proteins, and bands of increased intensity in the stimulated platelet fractions were digested and identified by FT-ICR mass spectrometry. Novel proteins were identified along with proteins known to be translocated to the platelet surface. Furthermore, many platelet proteins revealed changes in location associated with function, including G6B and Hip-55. HIP-55 is an SH3-binding protein important in T-cell receptor signalling. Further analysis of HIP-55 revealed that this adaptor protein becomes increasingly associated with both Syk and integrin beta 3 upon platelet activation. Analysis of HIP-55 deficient platelets revealed reduced fibrinogen binding upon thrombin stimulation, suggesting HIP-55 to be an important regulator of platelet function.