Contribuicao ao conhecimento dos efeitos da radiacao em cristais de KCl com impurezas de Sr

Tese (Doutoramento)

A Theoretical and Synthetic Investigation of New Donors for Organic Electro-Optic Chromophores: Understanding the Effects of Structure and Substituents on Donor Strength

Thesis (Ph.D.)--University of Washington, 2016-08

Elettrodeposizione di catalizzatori a base di Rh su schiume e fibre metalliche di FeCrAlloy per la produzione di syngas

The preparation of structured catalysts active in the catalytic partial oxidation of methane to syngas, was performed by electrosynthesis of hydroxides on FeCrAlloy foams and fibers. Rh/Mg/Al hydrotalcite-type compounds were prepared by co-precipitation of metallic cations on the support and successive calcination. Electrochemical reactions have been studied during the electrodeposition by linear sweep voltammetry. The experiments were performed at supports immersed in KNO3, KCl, Mg2+ and Al3+ aqueous solutions, starting by different precursors (nitrate and chlorides salts) and modifying the Mg/A ratio. Rh/Mg/Al hydrotalcite-type compounds were deposited on metal foams by applying a -1.2V vs SCE potential for 2000s with a nitrate solution of 0.06M total metal concentration. Firstly it was studied the effect of Mg on the coating propierties, modifying the Rh/Mg/Al atomic ratio (5/70/25, 5/50/45, 5/25/70 e 5/0/95). Then the effect of the amount of Rh was later investigated in the sample with the largest Mg content (Rh/Mg/Al = 5/70/25 and 2/70/28).The results showed that magnesium allowed obtaining the most homogeneous and well adherent coatings, wherein rhodium was well dispersed. The sample with the Rh/Mg /Al ratio equal to5/70/25 showed the best catalytic performances. Decreasing the Rh content, the properties of the coating were not modified, but the catalytic activity was lower, due to a not enough number of active sites to convert the methane. The work on metal fibers focused on the effect of precursor concentration, keeping constant composition, potential and synthesis time at the values of Rh/Mg/Al =5/70/25, -1.2V vs SCE and 1000s. However fibers geometry did not allow to obtain a high quality coating, even if results were quite promising.

Studies on the Catalytic Asymmetric Fischer Indolization

This work describes further developments and applications of the catalytic asymmetric Fischer indolization. In the first part of this thesis, the development of an organocatalytic asymmetric synthesis of helicenes via a Fischer indolization is discussed. The application of a novel SPINOL-derived phosphoric acid, featuring extended π-surfaces as 3,3‘-substituents which can potentially participate in π-interactions with the polyaromatic intermediate, afforded the corresponding products in high yields and enantioselectivities. The second part of this work describes the development of a catalytic asymmetric dearomatizing synthesis of 1,4-diketones via an interrupted Fischer indolization. Employing aryl hydrazines with α-substituents next to the hydrazine group prevents the rearomatization which takes place in common Fischer indole syntheses, thus enabling the hydrolysis of the generated diimine species. In the presence of STRIP as catalyst, a variety of different 1,4-diketones could be obtained in generally high yields, diastereo- and enantioselectivities. The last part of this thesis deals with the development of an organocatalytic asymmetric stereodivergent synthesis of novel 3H- and 2H-pyrroles, applying an interrupted Fischer indolization and for the 2H-pyrroles a subsequent stereospecific [1,5]-alkyl shift. Employing STRIP as catalyst afforded the corresponding products in good to excellent yields and enantioselectivities. Preliminary biological investigations of these novel structure motifs in cell-based assays, monitoring biological signal transduction pathways showed an inhibition of the Hedgehog signaling pathway in a μM range.

Développement de la polymérisation par (hétéro)arylation directe pour l’électronique organique

L’électronique organique suscite un intérêt grandissant en recherche grâce aux nouvelles possibilités qu’elle offre pour faciliter l’intégration de dispositifs électroniques dans nos vies. Grâce à elle, il est possible d’envisager des produits légers, flexibles et peu coûteux à produire. Les classes majeures de dispositifs étudiées sont les cellules photovoltaïques organiques (CPO) et les transistors organiques à effet de champ (TOEC). Dans les dernières années, une attention particulière a été portée sur les méthodes de polymérisation des matériaux organiques entrant dans la fabrication de ces dispositifs. La polymérisation par (hétéro)arylation directe (PHAD) catalysée au Pd offre une synthèse sans dérivé organométallique utilisant simplement un lien C-H aromatique, ce qui facilite la purification, diminue le nombre d’étapes et rend possible la production de matériaux à plus faible coût. De plus, la PHAD permet la préparation de matériaux qui était difficile, voire impossible, à obtenir auparavant. Cependant, l’inconvénient majeur de la PHAD reste sa limitation à certaines classes de polymères possédant des monomères ayant des positions bloquées favorisant qu’une seule paire de liaisons C-H. Dans le cadre de ces travaux de doctorat, l’objectif général est d’étudier la polymérisation par PHAD afin d’accéder à des classes de monomères qui n’étaient pas envisageables auparavant et à étendre l’application de cet outil dans le domaine des polymères conjugués. Plus spécifiquement, nous avons étudié l’utilisation de groupements protecteurs et partants sur des unités de benzodithiophènes et de bithiophène-silylés. Suivant ces résultats, nos travaux ont porté sur la polymérisation de dérivés de bithiophènes avec des bromo(aryle)s, une classe de polymères fréquemment utilisée en électronique organique mais qui était jugée impossible à polymériser par PHAD auparavant. Cette étude a montré l’importance de contrôler la PHAD afin d’obtenir le polymère souhaité. Finalement, nous avons étudié l’effet du système catalytique sur le taux de β−ramifications lors de la synthèse de polymères à base de thiophènes. Dans cette dernière étude, nous avons démontré l’importance d’utiliser des outils de caractérisation adéquats afin de confirmer la qualité des polymères obtenus.

Ferulates and lignin structural composition in cork

The structure of lignin and suberin, and ferulic acid (FA) content in cork from Quercus suber L. were studied. Extractive-free cork (Cork), suberin, desuberized cork (Cork(sap)), and milled-cork lignins (MCL) from Cork and Cork(sap) were isolated. Suberin composition was determined by GC-MS/FID, whereas the polymers structure in Cork, Corksap, and MCL was studied by Py-TMAH and 2D-HSQC-NMR. Suberin contained 94.4% of aliphatics and 3.2% of phenolics, with 90% of omega-hydroxyacids and alpha,omega-diacids. FA represented 2.7% of the suberin monomers, overwhelmingly esterified to the cork matrix. Py-TMAH revealed significant FA amounts in all samples, with about 3% and 6% in cork and cork lignins, respectively. Py-TMAH and 2D-HSQC-NMR demonstrated that cork lignin is a G-lignin (>96% G units), with a structure dominated by beta-O-4' alkyl-aryl ether linkages (80% and 77% of all linkages in MCL and MCLsap, respectively), followed by phenylcoumarans (18% and 20% in MCL and MCLsap, respectively), and smaller amounts of resinols (ca. 2%) and dibenzodioxocins (1%). HSQC also revealed that cork lignin is heavily acylated (ca. 50%) exclusively at the side-chain gamma-position. Ferulates possibly have an important function in the chemical assembly of cork cell walls with a cross-linking role between suberin, lignin and carbohydrates.

Chemistry of potassium halides and their role in corrosion in biomass and waste firing

Compared to the use of traditional fossil fuels (coal, oil, natural gas), combustion of biomass and waste fuels has several environmental and economic advantages for heat and power generation. However, biomass and waste fuels might contain halogens (Cl, Br, F), alkali metals (Na, K) and heavy metals (Zn, Pb), which may cause harmful emissions and corrosion problems. Hightemperature corrosion occurs typically on furnace waterwalls and superheaters. The corrosion of the boiler tube materials limits the increase of thermal efficiency of steam boilers and leads to costly shutdowns and repairs. In recent years, some concerns have been raised about halogen (Cl, Br, and F)-related hightemperature corrosion in biomass- and waste-fired boilers. Chlorine-related high-temperature corrosion has been studied extensively. The presence of alkali chlorides in the deposits is believed to play a major role in the corrosion observed in biomass and waste fired boilers. However, there is much less information found in literature on the corrosion effect of bromine and fluorine. According to the literature, bromine is only assumed to play a role similar to chlorine; the role of fluorine is even less understood. In this work, a series of bubbling fluidized bed (BFB) bench-scale tests were carried out to characterize the formation and sulfation behaviors of KCl and KBr in BFB combustion conditions. Furthermore, a series of laboratory tests were carried out to investigate the hightemperature corrosion behaviors of three different superheater steels (10CrMo9-10, AISI 347 and Sanicro 28) exposed to potassium halides in ambient air and wet air (containing 30% H2O). The influence of H2O and O2 on the high-temperature corrosion of steels both with and without a salt (KCl) in three gas atmospheres (2% H2O-30% O2-N2, 2% H2O-2% O2-N2 and 30% H2O-2% O2-N2) was also studied. From the bench-scale BFB combustion tests, it was found that HBr has a clearly higher affinity for the available K forming KBr than HCl forming KCl. The tests also indicated that KCl has a higher tendency for sulfation than KBr. From the laboratory corrosion tests in ambient air (also called “dry air” in Paper III and Paper IV), it was found that at relatively low temperatures (≤ 550 °C) the corrosivity of KBr and KF are similar to KCl. At 600 °C, KF showed much stronger corrosivity than KBr and KCl, especially for 10CrMo9-10 and AISI 347. When exposed to KBr or KF, 10CrMo9-10 was durable at least up to 450 °C, while AISI 347 and Sanicro 28 were durable at least up to 550 °C. From the laboratory corrosion tests in wet air (30% H2O), no obvious effect of water vapor was detected at 450 °C. At 550 °C, the influence of water vapor became significant in some cases, but the trend was not consistent. At 550 °C, after exposure with KBr, 10CrMo9-10 suffered from extreme corrosion; after exposure with KF and KCl, the corrosion was less severe, but still high. At 550 °C, local deep pitting corrosion occurred on AISI 347 and Sanicro 28 after exposure with KF. Some formation of K2CrO4 was observed in the oxide layer. At 550 °C, AISI 347 and Sanicro 28 suffered from low corrosion (oxide layer thickness of < 10 μm) after exposure with KBr and KCl. No formation of K2CrO4 was observed. Internal oxidation occurred in the cases of AISI 347 with KBr and KCl. From the laboratory corrosion tests in three different gas atmospheres (2% H2O-30% O2-N2, 2% H2O-2% O2-N2 and 30% H2O-2% O2-N2), it was found that in tests with no salt, no corrosion occurred on AISI 347 and Sanicro 28 up to 600 °C in both the “O2-rich” (2% H2O-30% O2-N2) and “H2O-rich” (30% H2O-2% O2-N2) gas atmospheres; only 10CrMo9-10 showed increased corrosion with increasing temperature. For 10CrMo9-10 in the “O2-rich” atmosphere, the presence of KCl significantly increased the corrosion compared to the “no salt” cases. For 10CrMo9-10 in the “H2O-rich” atmosphere, the presence or absence of KCl did not show any big influence on corrosion. The formation of K2CrO4 was observed only in the case with the “O2-rich” atmosphere. Considering both the results from the BFB tests and the laboratory corrosion tests, if fuels containing Br were to be combusted, the corrosion damage of superheaters would be expected to be higher than if the fuels contain only Cl. Information generated from these studies can be used to help the boiler manufacturers in selecting materials for the most demanding combustion systems.

Queijo minas padrão com reduzido teor de sódio: composição e caracterização sensorial

Sodium is an essential nutrient with important functions in the organism, however, its ingestion in excess may cause various health problems such as arterial hypertension, brain diseases, heart failure and chronic renal failure. In this context, the present study proposes to prepare Minas Padrão cheese with different contents of sodium with the objective of evaluating the effect of the addition of potassium chloride in sensory characteristics and hysicochemical properties, as well as in the proximal composition and in microbiological quality. The cheeses were elaborate in concentrations of 100% of NaCl (C), 80% of NaCl + 20% of KCl (T1), 60% of NaCl + 40% of KCl (T2), 40% of NaCl + 60% of KCl (T3) and 20% of NaCl + 80% of KCl (T4) and stored for 20 days at 10 ºC. The proximal composition and physicochemical was based on the determination of moisture content, fat, protein, ash, chloride, sodium, potassium, titratable acidity and pH of all treatments after 20 days of storage. The microbiological quality of the samples was monitored through the count of Total Coliforms and Escherichia coli, Staphylococcus aureus, Salmonella spp., mold and yeast in the first and fifteenth day of storage. The sensorial characterization was performed by the technique of Free Profile choice. The results showed that the replacement of sodium chloride by potassium in the Minas Padrão cheese in concentration higher than 40% presented significantly higher moisture contents. Cheese with a reduction greater than 60% of sodium obtained significantly effect in the titratable acidity, presenting higher values compared to the other treatments. The cheese with 20% of salt replacement did not differ statistically in relation to the control. When the proportion of substituent was increased, a significant reduction of the sodium content of up to 73% was observed. As the sodium was replaced by potassium in cheese, the potassium content increased significantly, stablishing a reduction of 82% in relation to the control. There was no effect to sodium substitution by potassium in fat, protein, ash and chlorides, as well as the pH values. The microbiological results were in accordance with the current legislation, therefore suitable to be eaten. According to the Free Profile Choice technique it was observed that the control C cheese (100% of NaCl) showed results very close to the other treatments, differing only in flavor attributes. The replacement of sodium by potassium in proportions of 20% contributed to a bitter taste detected by the tasters. Whereas, the appearance, flavor and texture attributes showed no significant differences compared to the Minas Padrão cheese.

EXCITON ENGINEERING THROUGH TUNALBLE FLUORESCENT QUANTUM DEFECTS

This thesis demonstrates exciton engineering in semiconducting single-walled carbon nanotubes through tunable fluorescent quantum defects. By introducing different functional moieties on the sp2 lattice of carbon nanotubes, the nanotube photoluminescence is systematically tuned over 68 meV in the second near-infrared window. This new class of quantum emitters is enabled by a new chemistry that allows covalent attachment of alkyl/aryl functional groups from their iodide precursors in aqueous solution. Using aminoaryl quantum defects, we show that the pH and temperature of complex fluids can be optically measured through defect photoluminescence that encodes the local environment information. Furthermore, defect-bound trions, which are electron-hole-electron tri-carrier quasi-particles, are observed in alkylated single-walled carbon nanotubes at room temperature with surprisingly high photoluminescence brightness. Collectively, the emission from defect-bound excitons and trions in (6,5)-single walled carbon nanotubes is 18-fold brighter than that of the native exciton. These findings pave the way to chemical tailoring of the electronic and optical properties of carbon nanostructures with fluorescent quantum defects and may find applications in optoelectronics and bioimaging.

Novel Anti-Campylobacter Compounds Identified Using High Throughput Screening of a Pre-selected Enriched Small Molecules Library

Campylobacter is a leading cause of foodborne bacterial gastroenteritis worldwide and infections can be fatal. The emergence of antibiotic-resistant Campylobacter spp. necessitates the development of new antimicrobials. We identified novel anti-Campylobacter small molecule inhibitors using a high throughput growth inhibition assay. To expedite screening, we made use of a “bioactive” library of 4,182 compounds that we have previously shown to be active against diverse microbes. Screening for growth inhibition of Campylobacter jejuni, identified 781 compounds that were either bactericidal or bacteriostatic at a concentration of 200 µM. Seventy nine of the bactericidal compounds were prioritized for secondary screening based on their physico-chemical properties. Based on the minimum inhibitory concentration against a diverse range of C. jejuni and a lack of effect on gut microbes, we selected 12 compounds. No resistance was observed to any of these 12 lead compounds when C. jejuni was cultured with lethal or sub-lethal concentrations suggesting that C. jejuni is less likely to develop resistance to these compounds. Top 12 compounds also possessed low cytotoxicity to human intestinal epithelial cells (Caco-2 cells) and no hemolytic activity against sheep red blood cells. Next, these 12 compounds were evaluated for ability to clear C. jejuni in vitro. A total of 10 compounds had an anti-C. jejuni effect in Caco-2 cells with some effective even at 25 µM concentrations. These novel 12 compounds belong to five established antimicrobial chemical classes; piperazines, aryl amines, piperidines, sulfonamide and pyridazinone. Exploitation of analogues of these chemical classes may provide Campylobacter specific drugs that can be applied in both human and animal medicine.

(E)-2-[2-(2-Aminofenil)vinil]-1-metilquinolin-4(1H)-ona como precursor de novos compostos heterociclicos

Esta dissertação reporta a síntese de novos derivados de 4-quinolonas com potencial atividade biológica e está dividida em 3 capítulos. No primeiro capítulo é feita uma breve introdução aos compostos do tipo 4quinolona, azepina e indol, focando a nomenclatura, atividade biológica e métodos de síntese mais comuns deste tipo de compostos, e é apresentada a nomenclatura dos compostos sintetizados ao longo deste trabalho. No segundo capítulo são descritas as metodologias desenvolvidas para obtenção dos compostos pretendidos. Foram sintetizados novos derivados de 4-quinolonas via reações de N-metilação seguida de ciclização in situ da (E)-N(2-acetilfenil)-3-(2-nitrofenil)acrilamida, via reações de redução da 1-metil-2-[2(2-nitrofenil)vinil]quinolin-4(1H)-ona e reações de halogenação da 1-metil-2-[2(2-nitrofenil)vinil]quinolin-4(1H)-ona e da 2-[2-(2-aminofenil)vinil]-1metilquinolin-4(1H)-ona. Posteriormente, fizeram-se estudos de reatividade da 1-metil-2-[2-(2-nitrofenil)vinil]quinolin-4(1H)-ona e da 2-[2-(2-aminofenil)vinil]-3bromo-1-metilquinolin-4(1H)-ona. Na reação de redução in situ seguida de ciclização intramolecular da 1-metil-2-[2-(2-nitrofenil)vinil]quinolin-4(1H)-ona obteve-se a 2-(1H-indol-2-il)-1-metilquinolin-4(1H)-ona. Partindo da 2-[2-(2aminofenil)vinil]-3-bromo-1-metilquinolin-4(1H)-ona via reações de BuchwaldHartwig obteve-se a 11-metil-5H-benzo[6,7]azepino[3,2-b]quinolin-6(11H)-ona. Novas N-[2-(2-(3-bromo-1-metil-4-oxo-1,4-di-hidroquinolin-2il)vinil)fenil]alquilamidas foram obtidas via reações de acilação da 2-[2-(2aminofenil)vinil]-3-bromo-1-metilquinolin-4(1H)-ona em piridina seca usando diferentes cloretos de acilo. Numa tentativa de ciclização intramolecular da N[2-(2-(3-bromo-1-metil-4-oxo-1,4-di-hidroquinolin-2-il)vinil)fenil]-hexanamida via reação de Ullmann intramolecular foi obtida a 2-(1-hexanoil-1H-indol-2-il)-1metilquinolin-4(1H)-ona. Após a descrição detalhada das metodologias de síntese são apresentadas as principais conclusões deste trabalho e perspectivas futuras. Por último, no terceiro capítulo, são apresentados os procedimentos experimentais usados para obtenção dos compostos sintetizados e os dados relativos à sua caracterização estrutural, que foi sendo discutida ao longo do segundo capítulo. Os compostos sintetizados foram caracterizados por espetroscopia de ressonância magnética nuclear monodimensional (1H e 13C) e bidimensional (HSQC, HMBC) e por espetrometria de massa e sempre que possível por espetrometria de massa de alta resolução.