A Review On The Production Of Levulinic Acid And Furanics From Sugars

Sugarcane products represent an abundant and relatively low cost carbon resource that can be utilised to produce chemical intermediates such as levulinic acid and furanics. These chemicals can be easily upgraded to commodity and specialty chemicals and biofuels by high yielding and well established technologies. However, there are challenges and technical hurdles that need to be overcome before these chemical intermediates can be cost-effectively produced in commercial quantities. The paper reviews production of levulinic acid and furanics from sugars by homogeneous mineral acid catalysts, and reports on preliminary studies on the production of these compounds with environmentally friendly biodegradable sulfonic acids. The yields (>50% of theoretical) of levulinic acid, formic acid and furfural obtained with these organic acids are comparable to that of sulphuric acid currently used for their production.

Older driver safety and mobility : where to from here?

The older adult population (65 years and over) represents a rapid growing segment of the population in many developed countries. Unlike earlier cohorts of older drivers that included many who were familiar with public transportation, the present cohort of older drivers historically has a greater reliance on the private automobile as their main form of transportation. Recent studies of older adults’ travel patterns reported automobile to be responsible for over 80% of the total number of hours spent on all trips. While older drivers, as a group, does not demonstrate a particular road risk, the evident demographic change and the increased physical fragility and severity of crash-related injuries makes older driver safety a prevalent public health issue. This study systematically reviewed the safety and mobility outcomes of existing strategies used internationally to manage older driver safety, with a specific focus on age-based testing (ABT), license restriction and self-regulation (i.e. voluntary limiting driving in potentially hazardous situations). ABT remains the most commonly adopted strategy by licensing authorities both within Australia and internationally. Heterogeneity in the development of functional declines, and in driving behaviours within the older driver population, makes age an unreliable index of driving capacity. Given the counter-productive safety and mobility outcomes of ABT strategies, their continued popularity within both the legislative and public domains remains problematic. Self-regulation may provide greater potential for reducing older drivers’ crash risk while maintaining their mobility and independence. The current body of literature on older drivers’ self-regulation is systematically reviewed. Despite being promoted by researchers and licensing authorities as a strategy to maintain older driver safety and mobility, the proportion of older drivers who self-regulate, and exactly how they do so, remains unclear. Future research on older drivers’ adoption of self-regulation, particularly the underlying psychological factors that underlies this process, is needed in order to promote its use within the older driver community.

Prevention of surgical site infection in total joint arthroplasty : an international tertiary care center survery

Background Prevention strategies are critical to reduce infection rates in total joint arthroplasty (TJA), but evidence-based consensus guidelines on prevention of surgical site infection (SSI) remain heterogeneous and do not necessarily represent this particular patient population. Questions/Purposes What infection prevention measures are recommended by consensus evidence-based guidelines for prevention of periprosthetic joint infection? How do these recommendations compare to expert consensus on infection prevention strategies from orthopedic surgeons from the largest international tertiary referral centers for TJA? Patients and Methods A review of consensus guidelines was undertaken as described by Merollini et al. Four clinical guidelines met inclusion criteria: Centers for Disease Control and Prevention's, British Orthopedic Association, National Institute of Clinical Excellence's, and National Health and Medical Research Council's (NHMRC). Twenty-eight recommendations from these guidelines were used to create an evidence-based survey of infection prevention strategies that was administered to 28 orthopedic surgeons from members of the International Society of Orthopedic Centers. The results between existing consensus guidelines and expert opinion were then compared. Results Recommended strategies in the guidelines such as prophylactic antibiotics, preoperative skin preparation of patients and staff, and sterile surgical attire were considered critically or significantly important by the surveyed surgeons. Additional strategies such as ultraclean air/laminar flow, antibiotic cement, wound irrigation, and preoperative blood glucose control were also considered highly important by surveyed surgeons, but were not recommended or not uniformly addressed in existing guidelines on SSI prevention. Conclusion Current evidence-based guidelines are incomplete and evidence should be updated specifically to address patient needs undergoing TJA.

Lung recruitment manoeuvres for reducing respiratory morbidity in mechanically ventilated neonates

This is the protocol for a review and there is no abstract. The objectives are as follows: To determine the evidence supporting the use of recruitment manoeuvres in mechanically ventilated neonates and identify the optimal method of lung recruitment. To determine the effects of lung recruitment manoeuvres in neonates receiving ventilatory support on neonatal mortality and development of chronic lung disease when compared to no recruitment. If data are available, subgroup analyses will include: chronological age, gestational age, lung pathophysiology and pre-existing lung disease, mode and length of ventilation, timing and frequency of recruitment techniques.

The effectiveness of an intervention in reducing risk of dioxin exposure in Da Nang : changes in community knowledge, attitudes and prevention practices after 2.5 years

Introduction Environmental and biological samples taken around Da Nang Air Base have shown elevated levels of dioxin over many years [1-3]. A pre-intervention knowledge, attitudes and practices (KAP) survey (2009), a risk reduction program (2010) and a post intervention KAP survey (2011) were undertaken in four wards surrounding Danang Airbase. A follow-up evaluation was undertaken in 2013. Methods A KAP survey was implemented among 400 randomly selected food handlers. Eleven indepth interviews and four focus group discussions were also undertaken. Results The knowledge of respondents remained positive and/or improved at 2.5 years follow-up. There were no significant differences in attitudes toward preventing dioxin exposure across surveys; most respondents were positive in all three surveys. An increase in households (69.5%) undertaking measures to prevent exposure was observed, which was higher than in the pre-intervention survey (39.6%) and post- intervention survey (60.4%) (χ2 = 95.6; p < 0.001). The proportion of respondents practicing appropriate preventive measures was also significantly improved. Conclusions Despite most of the intervention program’s activities ceasing in 2010, the risk reduction program has resulted in positive outcomes over the longer-term, with many knowledge and attitude measures remaining stable or imporving. Some KAP indicators decreased, but these KAP indicators were still significantly higher than the pre-intervention levels.

Influence of different nitrogen rates and DMPP nitrification inhibitor on annual N2O emissions from a subtropical wheat–maize cropping system

Global cereal production will need to increase by 50% to 70% to feed a world population of about 9 billion by 2050. This intensification is forecast to occur mostly in subtropical regions, where warm and humid conditions can promote high N2O losses from cropped soils. To secure high crop production without exacerbating N2O emissions, new nitrogen (N) fertiliser management strategies are necessary. This one-year study evaluated the efficacy of a nitrification inhibitor (3,4-dimethylpyrazole phosphate—DMPP) and different N fertiliser rates to reduce N2O emissions in a wheat–maize rotation in subtropical Australia. Annual N2O emissions were monitored using a fully automated greenhouse gas measuring system. Four treatments were fertilized with different rates of urea, including a control (40 kg-N ha−1 year−1), a conventional N fertiliser rate adjusted on estimated residual soil N (120 kg-N ha−1 year−1), a conventional N fertiliser rate (240 kg-N ha−1 year−1) and a conventional N fertiliser rate (240 kg-N ha−1 year−1) with nitrification inhibitor (DMPP) applied at top dressing. The maize season was by far the main contributor to annual N2O emissions due to the high soil moisture and temperature conditions, as well as the elevated N rates applied. Annual N2O emissions in the four treatments amounted to 0.49, 0.84, 2.02 and 0.74 kg N2O–N ha−1 year−1, respectively, and corresponded to emission factors of 0.29%, 0.39%, 0.69% and 0.16% of total N applied. Halving the annual conventional N fertiliser rate in the adjusted N treatment led to N2O emissions comparable to the DMPP treatment but extensively penalised maize yield. The application of DMPP produced a significant reduction in N2O emissions only in the maize season. The use of DMPP with urea at the conventional N rate reduced annual N2O emissions by more than 60% but did not affect crop yields. The results of this study indicate that: (i) future strategies aimed at securing subtropical cereal production without increasing N2O emissions should focus on the fertilisation of the summer crop; (ii) adjusting conventional N fertiliser rates on estimated residual soil N is an effective practice to reduce N2O emissions but can lead to substantial yield losses if the residual soil N is not assessed correctly; (iii) the application of DMPP is a feasible strategy to reduce annual N2O emissions from sub-tropical wheat–maize rotations. However, at the N rates tested in this study DMPP urea did not increase crop yields, making it impossible to recoup extra costs associated with this fertiliser. The findings of this study will support farmers and policy makers to define effective fertilisation strategies to reduce N2O emissions from subtropical cereal cropping systems while maintaining high crop productivity. More research is needed to assess the use of DMPP urea in terms of reducing conventional N fertiliser rates and subsequently enable a decrease of fertilisation costs and a further abatement of fertiliser-induced N2O emissions.

Thermodynamic modeling of ethanol fumigation in a diesel engine

Due to rapidly diminishing international supplies of fossil fuels, such as petroleum and diesel, the cost of fuel is constantly increasing, leading to higher costs of living, as a result of the significant reliance of many industries on motor vehicles. Many technologies have been developed to replace part or all of a fossil fuel with bio-fuels. One of the dual fuel technologies is fumigation of ethanol in diesel engines, which injects ethanol into the intake air stream of the engine. The advantage of this is that it avoids any costly modification of the engine high pressure diesel injection system, while reducing the volume of diesel required and potentially increasing the power output and efficiency. This paper investigates the performance of a diesel engine, converted to implement ethanol fumigation. The project will use both existing experimental data, along with generating computer modeled results using the program AVL Boost. The data from both experiments and the numerical simulation indicate desirable results for the peak pressure and the indicated mean effective pressure (IMEP). Increase in ethanol substitution resulted in elevated combustion pressure and an increase in the IMEP, while the variation of ethanol injection location resulted in negligible change. These increases in cylinder pressure led to a higher work output and total efficiency in the engine as the ethanol substitution was increased. In comparing the numerical and experimental results, the simulation showed a slight elevation, due to the inaccuracies in the heat release models. Future work is required to improve the combustion model and investigate the effect of the variation of the location of ethanol injection.

Radiative and total heat transfer measurements to a Titan Explorer model

Radiative and total heat transfer at the flow stagnation point of a 1:40.8 binary scaled model of the Titan Explorer vehicle were measured in the X3 expansion tube. Results from the current study illustrated that with the addition of CH4 into a N2 test gas radiative heat transfer could be detected. For a test gas of 5% CH4 and 95% N2, simulating an atmospheric model for Titanic aerocapture, approximately 4% of the experimentally measured total stagnation point heat transfer was found to be due to radiation. This was in comparison to < 1% measured for a test gas of pure nitrogen. When scaled to the flight vehicle, experimental results indicate a 64% contribution of radiation (test gas 5% CH4/95% N2). Previous numerical results however have predicted this contribution to be between 80-92%. Thus, experimental results from the current study suggest that numerical analyses are over-predicting the radiative heat transfer on the flight vehicle.

Pore size distribution and accessible pore size distribution in bituminous coals

The porosity and pore size distribution of coals determine many of their properties, from gas release to their behavior on carbonization, and yet most methods of determining pore size distribution can only examine a restricted size range. Even then, only accessible pores can be investigated with these methods. Small-angle neutron scattering (SANS) and ultra small-angle neutron scattering (USANS) are increasingly used to characterize the size distribution of all of the pores non-destructively. Here we have used USANS/SANS to examine 24 well-characterized bituminous and subbituminous coals: three from the eastern US, two from Poland, one from New Zealand and the rest from the Sydney and Bowen Basins in Eastern Australia, and determined the relationships of the scattering intensity corresponding to different pore sizes with other coal properties. The range of pore radii examinable with these techniques is 2.5nm to 7μm. We confirm that there is a wide range of pore sizes in coal. The pore size distribution was found to be strongly affected by both rank and type (expressed as either hydrogen or vitrinite content) in the size range 250nm to 7μm and 5 to 10nm, but weakly in intermediate regions. The results suggest that different mechanisms control coal porosity on different scales. Contrast-matching USANS and SANS were also used to determine the size distribution of the fraction of the pores in these coals that are inaccessible to deuterated methane, CD4, at ambient temperature. In some coals most of the small (~10nm) pores were found to be inaccessible to CD4 on the time scale of the measurement (~30min–16h). This inaccessibility suggests that in these coals a considerable fraction of inherent methane may be trapped for extended periods of time, thus reducing the effectiveness of methane release from (or sorption by) these coals. Although the number of small pores was less in higher rank coals, the fraction of total pores that was inaccessible was not rank dependent. In the Australian coals, at the 10nm to 50nm size scales the pores in inertinites appeared to be completely accessible to CD4, whereas the pores in the vitrinite were about 75% inaccessible. Unlike the results for total porosity that showed no regional effects on relationships between porosity and coal properties, clear regional differences in the relationships between fraction of closed porosity and coal properties were found. The 10 to 50nm-sized pores of inertinites of the US and Polish coals examined appeared less accessible to methane than those of the inertinites of Australian coals. This difference in pore accessibility in inertinites may explain why empirical relationships between fluidity and coking properties developed using Carboniferous coals do not apply to Australian coals.

Metal ion levels post primary unilateral Exeter total hip arthroplasty

BACKGROUND: Metal ion release is common following total hip arthroplasty, yet postoperative levels have not been defined for most stems currently used in clinical practice. AIM: To assess metal ion release in the serum of patients with well functioning unilateral Exeter V40 primary total hip arthroplasties one year after surgery. METHODS: Whole blood chromium and serum cobalt levels were measured in 20 patients following primary total hip arthroplasty with the Exeter V40 stem and a variety of acetabular components one year after surgery. RESULTS: Whole blood chromium levels were within the normal range (10-100 nmol/L), with a single mild elevation of serum cobalt (normal < 20 nmol/L). CONCLUSION: In well functioning primary unilateral total hip arthroplasty using the Exeter V40 stem with a variety of acetabular components one year post surgery, whole blood chromium levels are normal and serum cobalt elevations are rare and mild.

Reducing complexity of large EPCs

Business processes are an important instrument for understanding and improving how companies provide goods and services to customers. Therefore, many companies have documented their business processes well, often in the Event-driven Process Chains (EPC). Unfortunately, in many cases the resulting EPCs are rather complex, so that the overall process logic is hidden in low level process details. This paper proposes abstraction mechanisms for process models that aim to reduce their complexity, while keeping the overall process structure. We assume that functions are marked with efforts and splits are marked with probabilities. This information is used to separate important process parts from less important ones. Real world process models are used to validate the approach.

A review on the production of levulinic acid and furanics from sugars

Sugarcane products represent an abundant and relatively low cost carbon resource that can be utilised to produce chemical intermediates such as levulinic acid and furanics. These chemicals can be easily upgraded to commodity and specialty chemicals and biofuels by high yielding and well established technologies. However, there are challenges and technical hurdles that need to be overcome before these chemical intermediates can be cost-effectively produced in commercial quantities. The paper reviews production of levulinic acid and furanics from sugars by homogeneous mineral acid catalysts, and reports on preliminary studies on the production of these compounds with environmentally friendly biodegradable sulfonic acids. The yields (>50% of theoretical) of levulinic acid, formic acid and furfural obtained with these organic acids are comparable to that of sulphuric acid currently used for their production.

Total energy shaping of a class of underactuated Port-Hamiltonian Systems using a new set of closed-loop potential shape variables

This paper proposes a method for designing set-point regulation controllers for a class of underactuated mechanical systems in Port-Hamiltonian System (PHS) form. A new set of potential shape variables in closed loop is proposed, which can replace the set of open loop shape variables-the configuration variables that appear in the kinetic energy. With this choice, the closed-loop potential energy contains free functions of the new variables. By expressing the regulation objective in terms of these new potential shape variables, the desired equilibrium can be assigned and there is freedom to reshape the potential energy to achieve performance whilst maintaining the PHS form in closed loop. This complements contemporary results in the literature, which preserve the open-loop shape variables. As a case study, we consider a robotic manipulator mounted on a flexible base and compensate for the motion of the base while positioning the end effector with respect to the ground reference. We compare the proposed control strategy with special cases that correspond to other energy shaping strategies previously proposed in the literature.

What aspects of demographic, personality, attitudes, and perceptions of law enforcement influence self-reported likelihood of drink driving?

The aim of the current study was to examine the associations between a number of individual factors (demographic factors (age and gender), personality factors, risk-taking propensity, attitudes towards drink driving, and perceived legitimacy of drink driving enforcement) and how they influence the self-reported likelihood of drink driving. The second aim of this study was to examine the potential of attitudes mediating the relationship between risk-taking and self-reported likelihood of drink driving. In total, 293 Queensland drivers volunteered to participate in an online survey that assessed their self-reported likelihood to drink drive in the next month, demographics, traffic-related demographics, personality factors, risk-taking propensity, attitudes towards drink driving, and perceived legitimacy of drink driving enforcement. An ordered logistic regression analysis was utilised to evaluate the first aim of the study; at the first step the demographic variables were entered; at step two the personality and risk-taking were entered; at the third step, the attitudes and perceptions of legitimacy variables were entered. Being a younger driver and having a high risk-taking propensity were related to self-reported likelihood of drink driving. However, when the attitudes variable was entered, these individual factors were no longer significant; with attitudes being the most important predictor of self-reported drink driving likelihood. A significant mediation model was found with the second aim of the study, such that attitudes mediated the relationship between risk-taking and self-reported likelihood of drink driving. Considerable effort and resources are utilised by traffic authorities to reducing drink driving on the Australian road network. Notwithstanding these efforts, some participants still had some positive attitudes towards drink driving and reported that they were likely to drink drive in the future. These findings suggest that more work is needed to address attitudes regarding the dangerousness of drink driving.

Stop and revive? The effectiveness of nap and active rest breaks for reducing drivers sleepiness

The purpose of this study was to compare the effects of two commonly utilised sleepiness countermeasures: a nap break and an active rest break. The effects of the countermeasures were evaluated by physiological (EEG), subjective, and driving performance measures. Participants completed two hours of simulated driving, followed by a 15 minute nap break or a 15 minute active rest break then completed the final hour of simulated driving. The nap break reduced EEG and subjective sleepiness. The active rest break did not reduce EEG sleepiness, with sleepiness levels eventually increasing, and resulted in an immediate reduction of subjective sleepiness. No difference was found between the two breaks for the driving performance measure. The immediate reduction of subjective sleepiness after the active rest break could leave drivers with erroneous perceptions of their sleepiness, particularly with increases of physiological sleepiness after the break.