Critical aspects on the behavior of material from the mechanical tool-workpiece interaction in single point diamond turning

Some material aspects such as grain size, purity and anisotropy exert an important influence on surface quality, especially in single point diamond turning. The aim of this paper is to present and discuss some critical factors that can limit the accuracy of ultraprecision machining of non-ferrous metals and to identify the effects of them on the cutting mechanism with single point diamond tools. This will be carried out through observations of machined surfaces and chips produced using optical and scanning electron microscopy. Solutions to reduce the influence of some of these limiting factors related with the mechanism of generation of mirror-like surfaces will be discussed.

Investigation on diamond turning of silicon crystal - generation mechanism of surface cut with worn tool

This paper discusses the effect of tool wear on surface finish in single-point diamond turning of single crystal silicon. The morphology and topography of the machined surface clearly show the type of cutting edge wear reproduced onto the cutting grooves. Scanning electron microscopy is used in order to correlate the cutting edge damage and microtopography features observed through atomic force microscopy. The possible wear mechanisms affecting tool performance and surface generation during cutting are also discussed. The zero degree rake angle single point diamond tool presented small nicks on the cutting edge. The negative rake angle tools presented more a type of crater wear on the rake face. No wear was detected on flank face of the diamond tools.

Influence of Cutting Conditions on Tool Life, Tool Wear and Surface Finish in the Face Milling Process

The main goal of this work is to study the influence of cutting conditions - cutting speed, feed velocity and feed per tooth - on tool life and surface finish of the workpiece in the face milling of flat surfaces. Aiming to achieve this goal, several milling experiments were carried out with different cutting speeds, feed velocities and feeds per tooth. In the first phase of the experiments, cutting speed was varied without varying feed velocity, which caused a variation in feed per tooth. In the second phase of the experiments, cutting speed and feed velocity were varied in such a way that feed per tooth was kept constant. Tool flank wear and surface roughness of the workpiece were measured as cutting time elapsed. The main conclusions of this work are that a) cutting speed has a strong influence on tool life, regardless of whether feed velocity or feed per tooth varies and b) an increase in surface roughness of the workpiece is not closely related to an increase in wear of the primary cutting edge.

Hot tool temperature analysis though infrared images

Textile manufacture occupies a prominent place in the national economy. Because of its importance researches have been made on the development of new materials, equipment and methods used in the production process. The cutting of textiles starts in the basic stage, to be followed by the process of the making of clothes and other articles. In the hot cutting of fabric, one of the variables of great importance in the control of the process is the contact temperature between the tool and the fabric. This work presents a technique for the measurement of the temperature based on the processing of infrared images. With this purpose, it was developed a system which is composed of an infrared camera, a framegrabber PC board and a software which analyses the punctual temperature in the cut area enabling the operator to achieve the necessary control of other variables involved in the process.

Indoor Localization Solutions for a Marine Industry Augmented Reality Tool

In this report are described means for indoor localization in special, challenging circum-stances in marine industry. The work has been carried out in MARIN project, where a tool based on mobile augmented reality technologies for marine industry is developed. The tool can be used for various inspection and documentation tasks and it is aimed for improving the efficiency in design and construction work by offering the possibility to visualize the newest 3D-CAD model in real environment. Indoor localization is needed to support the system in initialization of the accurate camera pose calculation and auto-matically finding the right location in the 3D-CAD model. The suitability of each indoor localization method to the specific environment and circumstances is evaluated.

Ristikkorakenteisen hihnakuljetinsillan mitoitustyökalun kehittäminen

Hihnakuljettimia käytetään muun muassa voimalaitos- ja sellutehdasympäristöissä kuljettamaan kiinteää polttoainetta tai haketta pitkiä matkoja. Pitkät hihnakuljettimet asennetaan yleensä teräsristikoista rakennettujen kuljetinsiltojen sisään. Kuljetinsilta toimii siis hihnakuljettimen ja hoitokäytävän runkona sekä suojaa kuljetinta ja kuljetettavaa materiaalia säältä. Tässä diplomityössä on laadittu mitoitustyökalu, jolla voidaan nopeasti mitoittaa ristikkorakenteisen hihnakuljetinsillan sauvat sekä määrittää rakenteen massa. Laskentaohjelma on toteutettu Microsoft Excel -taulukkolaskentana. Sillan poikkileikkaus voi olla suljettu symmetrinen umpirakenne tai avorakenne, jossa on ulokkeellinen hoitotaso. Ristikon sauvat ovat RHS-putkia. Rakenteeseen voi vaikuttaa jatkuvia kuormia, pistekuormia sekä näistä johdetut, ekvivalenttiin staattiseen voimaan perustuvat maanjäristyskuormat. Diplomityössä on perehdytty mitoitustyökalussa sovellettuihin teorioihin. Voimasuureiden laskenta perustuu 2-tukisina palkkeina käsiteltävien siltalohkojen ratkaisuun ja palkkianalogiaan, jossa ristikon sauvavoimat ratkaistaan käsittelemällä ristikkoa palkkina. Sauvojen kestävyyden laskenta perustuu SFS-EN 1993-1-1 -normiin, joka on osa Eurocode -rakennesuunnittelunormistoa. Lisäksi työssä on käsitelty ristikkoliitosten mitoitusta SFS-EN 1993-1-8 mukaan. Mitoitusohjelman toimivuutta on testattu tarkastelemalla esimerkkisiltaa laaditulla mitoituspohjalla ja Autodesk Robot Professional 2013 -FE-analyysiohjelmisuolla. Tulosten perusteella mitoitustyökalua voidaan käyttää ainakin tarjousvaiheen nopeisiin tarkasteluihin ja omamassan määritykseen, mutta myös lopulliseen mitoitukseen, mikäli hyväksytään konservatiivinen mitoitus.

“Development work thesis” as a tool for continuing professional education

Julkaisumaa: 158 TW TWN Taiwan

Diffusion Tensor Imaging as a Diagnostic and Research Tool: A Study on Preterm Infants

Diffusion tensor imaging (DTI) is an advanced magnetic resonance imaging (MRI) technique. DTI is based on free thermal motion (diffusion) of water molecules. The properties of diffusion can be represented using parameters such as fractional anisotropy, mean diffusivity, axial diffusivity, and radial diffusivity, which are calculated from DTI data. These parameters can be used to study the microstructure in fibrous structure such as brain white matter. The aim of this study was to investigate the reproducibility of region-of-interest (ROI) analysis and determine associations between white matter integrity and antenatal and early postnatal growth at term age using DTI. Antenatal growth was studied using both the ROI and tract-based spatial statistics (TBSS) method and postnatal growth using only the TBSS method. The infants included to this study were born below 32 gestational weeks or birth weight less than 1,501 g and imaged with a 1.5 T MRI system at term age. Total number of 132 infants met the inclusion criteria between June 2004 and December 2006. Due to exclusion criteria, a total of 76 preterm infants (ROI) and 36 preterm infants (TBSS) were accepted to this study. The ROI analysis was quite reproducible at term age. Reproducibility varied between white matter structures and diffusion parameters. Normal antenatal growth was positively associated with white matter maturation at term age. The ROI analysis showed associations only in the corpus callosum. Whereas, TBSS revealed associations in several brain white matter areas. Infants with normal antenatal growth showed more mature white matter compared to small for gestational age infants. The gestational age at birth had no significant association with white matter maturation at term age. It was observed that good early postnatal growth associated negatively with white matter maturation at term age. Growth-restricted infants seemed to have delayed brain maturation that was not fully compensated at term, despite catchup growth.

Perspectives for using light quality knowledge as an advanced ecophysiological weed management tool

The current knowledge of light quality effects on plant morphogenesis and development represents a new era of understanding on how plant communities perceive and adjust to available resources. The most important consequences of light quality cues, often mediated by decreasing in red far-red ratios with respect to the spectral composition of incident sunlight radiation, affecting weed-crop interaction are the increased plant height and shoot to root ratio in anticipation of competition by light quantity, water or nutrients. Although the concepts related to light quality have been extensively studied and several basic process of this phenomenon are well known, little applications of photomorphogenic signaling currently are related to agricultural problems or weed management. The objectives of this review are to describe how light quality change can be a triggering factor of interspecific interference responses, to analyze how this phenomenon can be used to predict weed interference, to reevaluate the critical periods of interference concept, and to discuss its potential contribution towards developing more weed competitive crop varieties. Knowledge on light quality responses involved in plant sensing of interspecific competition could be used to identify red/far-red threshold values, indicating when weed control should be started. Light quality alterations by weeds can affect grain crop development mainly in high yielding fields. Unlike the traditional concept or the critical period of competition, light quality mediated interference implies that the critical period for weed control could start before the effects of direct resource (water, nutrients and available light) limitation actually occur. The variability in light quality responses among crop genotypes and the identification of mutants insensitive to light quality effects indicate that this characteristic can be selected or modified to develop cultivars with enhanced interspecific interference ability. Knowledge on light quality-elicited responses represents a new possibility to understand the underlying biology of interspecific interference, and could be used in the development of new weed management technologies.

Design and implementation of a production synchronization extension for Microsoft Dynamics AX

In a just-in-time, assemble-to-order production environments the scheduling of material requirements and production tasks - even though difficult - is of paramount importance. Different enterprise resource planning solutions with master scheduling functionality have been created to ease this problem and work as expected unless there is a problem in the material flow. This case-based candidate’s thesis introduces a tool for Microsoft Dynamics AX multisite environment, that can be used by site managers and production coordinators to get an overview of the current open sales order base and prioritize production in the event of material shortouts to avoid part-deliveries.

Reflectance indices as a diagnostic tool for weed control performed by multipurpose equipment in precision agriculture

Several tools of precision agriculture have been developed for specific uses. However, this specificity may hinder the implementation of precision agriculture due to an increasing in costs and operational complexity. The use of vegetation index sensors which are traditionally developed for crop fertilization, for site-specific weed management can provide multiple utilizations of these sensors and result in the optimization of precision agriculture. The aim of this study was to evaluate the relationship between reflectance indices of weeds obtained by the GreenSeekerTM sensor and conventional parameters used for weed interference quantification. Two experiments were conducted with soybean and corn by establishing a gradient of weed interference through the use of pre- and post-emergence herbicides. The weed quantification was evaluated by the normalized difference vegetation index (NDVI) and the ratio of red to near infrared (Red/NIR) obtained using the GreenSeekerTM sensor, the visual weed control, the weed dry matter, and digital photographs, which supplied information about the leaf area coverage proportions of weed and straw. The weed leaf coverage obtained using digital photography was highly associated with the NDVI (r = 0.78) and the Red/NIR (r = -0.74). The weed dry matter also positively correlated with the NDVI obtained in 1 m linear (r = 0.66). The results indicated that the GreenSeekerTM sensor originally used for crop fertilization could also be used to obtain reflectance indices in the area between rows of crops to support decision-making programs for weed control.

OCR Correction Tool for Linguistic Corpora

We introduce a new tool for correcting OCR errors of materials in a repository of cultural materials. The poster is aimed to all who are interested in digital humanities and who might find our tool useful. The poster will focus on the OCR correction tool and on the background processes. We have started a project on materials published in Finno-Ugric languages in the Soviet Union in the 1920s and 1930s. The materials are digitised in Russia. As they arrive, we publish them in DSpace (fennougrica.kansalliskirjasto.fi). For research purposes, the results of the OCR must be corrected manually. For this we have built a new tool. Although similar tools exist, we found in-house development necessary in order to serve the researchers' needs. The tool enables exporting the corrected text as required by the researchers. It makes it possible to distribute the correction tasks and their supervision. After a supervisor has approved a text as finalised, the new version of the work will replace the old one in DSpace. The project has - benefitted the small language communities, - opened channels for cooperation in Russia. - increased our capabilities in digital humanities. The OCR correction tool will be available to others.

Design and validation of stateful composite RESTful web services

A web service is a software system that provides a machine-processable interface to the other machines over the network using different Internet protocols. They are being increasingly used in the industry in order to automate different tasks and offer services to a wider audience. The REST architectural style aims at producing scalable and extensible web services using technologies that play well with the existing tools and infrastructure of the web. It provides a uniform set of operation that can be used to invoke a CRUD interface (create, retrieve, update and delete) of a web service. The stateless behavior of the service interface requires that every request to a resource is independent of the previous ones facilitating scalability. Automated systems, e.g., hotel reservation systems, provide advanced scenarios for stateful services that require a certain sequence of requests that must be followed in order to fulfill the service goals. Designing and developing such services for advanced scenarios with REST constraints require rigorous approaches that are capable of creating web services that can be trusted for their behavior. Systems that can be trusted for their behavior can be termed as dependable systems. This thesis presents an integrated design, analysis and validation approach that facilitates the service developer to create dependable and stateful REST web services. The main contribution of this thesis is that we provide a novel model-driven methodology to design behavioral REST web service interfaces and their compositions. The behavioral interfaces provide information on what methods can be invoked on a service and the pre- and post-conditions of these methods. The methodology uses Unified Modeling Language (UML), as the modeling language, which has a wide user base and has mature tools that are continuously evolving. We have used UML class diagram and UML state machine diagram with additional design constraints to provide resource and behavioral models, respectively, for designing REST web service interfaces. These service design models serve as a specification document and the information presented in them have manifold applications. The service design models also contain information about the time and domain requirements of the service that can help in requirement traceability which is an important part of our approach. Requirement traceability helps in capturing faults in the design models and other elements of software development environment by tracing back and forth the unfulfilled requirements of the service. The information about service actors is also included in the design models which is required for authenticating the service requests by authorized actors since not all types of users have access to all the resources. In addition, following our design approach, the service developer can ensure that the designed web service interfaces will be REST compliant. The second contribution of this thesis is consistency analysis of the behavioral REST interfaces. To overcome the inconsistency problem and design errors in our service models, we have used semantic technologies. The REST interfaces are represented in web ontology language, OWL2, that can be part of the semantic web. These interfaces are used with OWL 2 reasoners to check unsatisfiable concepts which result in implementations that fail. This work is fully automated thanks to the implemented translation tool and the existing OWL 2 reasoners. The third contribution of this thesis is the verification and validation of REST web services. We have used model checking techniques with UPPAAL model checker for this purpose. The timed automata of UML based service design models are generated with our transformation tool that are verified for their basic characteristics like deadlock freedom, liveness, reachability and safety. The implementation of a web service is tested using a black-box testing approach. Test cases are generated from the UPPAAL timed automata and using the online testing tool, UPPAAL TRON, the service implementation is validated at runtime against its specifications. Requirement traceability is also addressed in our validation approach with which we can see what service goals are met and trace back the unfulfilled service goals to detect the faults in the design models. A final contribution of the thesis is an implementation of behavioral REST interfaces and service monitors from the service design models. The partial code generation tool creates code skeletons of REST web services with method pre and post-conditions. The preconditions of methods constrain the user to invoke the stateful REST service under the right conditions and the post condition constraint the service developer to implement the right functionality. The details of the methods can be manually inserted by the developer as required. We do not target complete automation because we focus only on the interface aspects of the web service. The applicability of the approach is demonstrated with a pedagogical example of a hotel room booking service and a relatively complex worked example of holiday booking service taken from the industrial context. The former example presents a simple explanation of the approach and the later worked example shows how stateful and timed web services offering complex scenarios and involving other web services can be constructed using our approach.

Glyphosate as a tool to produce shikimic acid in plants

Oseltamivir phosphate is a potent viral inhibitor produced from shikimic acid extracted from seeds of Ilicium verum, the most important natural source. With the site of action 5-enolpyruvylshikimate-3-phosphate synthase (EPSP), glyphosate is the only compound capable of inhibiting its activity with the consequent accumulation of shikimic acid in plants. Corn and soybean plants were sprayed with reduced rates of glyphosate (0.0 to 230.4 g a.i. ha¹) and shikimic acid content in the dry mass was determined by HPLC 3, 7 and 10 days after application. Results showed shikimic acid accumulation in dry mass with increases of up to 969% in corn and 33,000% on soybeans, with peak concentrations 3 days after treatment (DAT). Industrial feasibility for shikimic acid production, combined with favorable climatic conditions for growing corn and soybean in virtually all over Brazil, favor the use of reduced rates of glyphosate in shikimic acid biosynthesis, with potential for use as an inducer in exploration of alternative sources for production of oseltamivir phosphate with low environmental impact.

Energiatehokkuuden huomioiminen julkisissa rakennushankkeissa

Hanke tähtää Lappeenrannan julkisen rakennuskannan energiatehokkuuden ja kokonaistaloudellisuuden parantamiseen. Energiatehokkuutta ja kokonaistaloudellisuutta kunnallisessa rakentamisessa kannustavat mm. kansainvälisten ja kansallisten sopimusten energiansäästötavoitteet, sekä kuntien tiukka budjettitilanne. Hankkeen yhteydessä on laadittu arviointikriteeristö rakennusinvestoinneista vastaavien viranomaisten käyttöön, mikä helpottaa tunnistamaan energiatehokkaita, kokonaistaloudellisia sekä laadukasta sisäilmastoa tukevia rakennusinvestointien toteutuskäytäntöjä. Kriteeristö on suunniteltu erityisesti kasvatus- ja opetustarkoituksiin suunnattuja rakennuksia varten. Jotta kokonaistaloudellisuustavoitteet täyttyisivät, työssä käytettiin hyväksi elinkaariajattelutapaa. Kriteerit laadittiin rakennuksen kolmelle tavoitteiden toteutumisen kannalta merkittävälle elinkaaren vaiheelle, eli suunnittelu-, toteutus- ja käyttövaiheelle. Kriteeristö on laadittu kirjallisuuden ja ammattilaisten haastattelujen tarjoaman tiedon pohjalta. Laadittua kriteeristöä koekäytettiin Myllymäen päiväkoti -hankkeen yhteydessä, jotta voitaisiin tunnistaa kriteeristön kehitystarpeita. Koekäytön yhteydessä toteutettiin myös mielipidekysely, jonka avulla kerättiin kriteeristön kehitysehdotuksia rakennushankkeen eri osapuolilta. Koekäytön tarjoaman tiedon nojalla kriteeristöä jatkokehitettiin vastaamaan paremmin käytännön tarpeita. Koekäyttö kohdistui kohteen suunnitteluvaiheeseen. Hankkeessa saavutettiin asetetut tavoitteet. Voidaan kuitenkin todeta, että kriteeristön jatkokehittämistä on syytä jatkaa. Koekäytön ulottaminen toteutus ja käyttövaiheeseen on tärkeää. Kriteeristön käsittelyalueen laajentamiselle korjausrakentamiseen sekä alueellisen tarkastelutavan käyttöönotolle olisi myös tarvetta.