Microstructure of shear localization in low-carbon ferrite pearlite steel

A study has been made of the microstructure of the thermally assisted band in a low carbon ferrite-pearlite steel, resulting from high speed torsional testing with an average strain rate of about 1500 s−1. Metallographic examination showed that there are several fine shear bands distributed over a deformed region (the gauge length of the specimen). The width of these bands is estimated to be of the order of magnitude of 50 μm, and the spacing between them is roughly about 100 μm. Detailed scanning electron microscopy studies indicate that damage of the microstructure within the band is very apparent, as evidenced by microcrack initiation and coalescence along the shear deformation band. However, there is no evidence that the material in the band had become microcrystalline or non-crystalline.

Mixed-mode fracture mechanisms near the fatigue threshold of aisi-316 stainless-steel

Near threshold, mixed mode (I and II), fatigue crack growth occurs mainly by two mechanisms, coplanar (or shear) mode and branch (or tensile) mode. For a constant ratio of ΔK_I/ΔK_II the shear mode growth shows a self-arrest character and it would only start again when ΔK_I and ΔK_II are increased. Both shear crack growth and the early stages of tensile crack growth, are of a crystallographic nature; the fatigue crack proceeds along slip planes or grain boundaries. The appearance of the fracture surfaces suggest that the mechanism of crack extension is by developing slip band microcracks which join up to form a macrocrack. This process is thought to be assisted by the nature of the plastic deformation within the reversed plastic zone where high back stresses are set up by dislocation pile-ups against grain boundaries. The interaction of the crack tip stress field with that of the dislocation pile-ups leads to the formation of slip band microcracks and subsequent crack extension. The change from shear mode to tensile mode growth probably occurs when the maximum tensile stress and the microcrack density in the maximum tensile plane direction attain critical values.

YAG激光毛化技术进展

二十世纪八十年代，当比利时冶金研究中心(CRM)开发出CO_2激光毛化冷轧辊技术后，尝试用YAG激光进行轧辊毛化一直吸引着众多的研究者，这是因为YAG(1.06μm)激光波长比CO_2(10.6μm)激光波长短一个量级，材料对YAG激光有更高的吸收率，并用YAG激光可以聚焦到更小的光斑尺寸，同时使用电信号驱动的声光开关技术便于对毛化分布进行可设定控制。但是用传统声光调制的YAG激光虽然可以碇以很高的脉冲频率(>30kHz)，但单脉冲有量仅为10mJ左右，难以达到辊面毛化粗糙度的要求，因此人们认为YAG激光用于毛化的主要困难是脉冲能量太小。

Formation and Structure of Composite Coating of HAD and Micro-Plasma Oxidation on A3 Steel

Composite coatings were obtained on A3 steel by hot dipping aluminum(HAD) at 720 degreesC for 6 min and micro-plasma oxidation (MPO) in alkali electrolyte. The surface morphology, element distribution and interface structure of composite coatings were studied by means of XRD, SEM and EDS. The results show that the composite coatings obtained through HAD/MPO on A3 steel consist of four layers. From the surface to the substrate, the layer is loose Al2O3 ceramic, compact Al2O3 ceramic, At and FeAl intermetallic compound layer in turn. The adhesions among all the layers are strengthened because the ceramic layer formed at the At surface originally, FeAl intermetallic compound layer and substrate are combined in metallurgical form through mutual diffusion during HAD process. Initial experiment results disclose that the anti-corrosion performance and wear resistance of composite coating are obviously improved through HAD/MPO treatment.

Transient Temperature Distribution in a Sheet Metal by Low-Energy Laser Scanning

Low-energy laser-heating techniques are widely used in engineering applications such as, thinfilm deposition, surface treatment, metal forming and micro-structural pattern formation. In this paper,under the conditions of ignoring the thermo-mechanical coupling, a numerical simulation on the spatialand temporal temperature distribution in a sheet metal produced by the laser beam scanning in virtue of thefinite element method is presented. Both the three-dimensional transient temperature field and thetemperature evolution as a function of heat penetrating depth in the metal sheet are calculated. Thetemperature dependence of material properties was taken into account. It was shown that, after taking thetemperature dependence of the material absorbance effect into consideration, the temperature change ratealong the scanning direction and the temperature maximum were both increased.

The Annual Economic Survey of Federal Gulf Shrimp Permit Holders: Report on the Design, Implementation, and Descriptive Results for 2006

This technical memorandum documents the design, implementation, data preparation, and descriptive results for the 2006 Annual Economic Survey of Federal Gulf Shrimp Permit Holders. The data collection was designed by the NOAA Fisheries Southeast Fisheries Science Center Social Science Research Group to track the financial and economic status and performance by vessels holding a federal moratorium permit for harvesting shrimp in the Gulf of Mexico. A two page, self-administered mail survey collected total annual costs broken out into seven categories and auxiliary economic data. In May 2007, 580 vessels were randomly selected, stratified by state, from a preliminary population of 1,709 vessels with federal permits to shrimp in offshore waters of the Gulf of Mexico. The survey was implemented during the rest of 2007. After many reminder and verification phone calls, 509 surveys were deemed complete, for an ineligibility-adjusted response rate of 90.7%. The linking of each individual vessel’s cost data to its revenue data from a different data collection was imperfect, and hence the final number of observations used in the analyses is 484. Based on various measures and tests of validity throughout the technical memorandum, the quality of the data is high. The results are presented in a standardized table format, linking vessel characteristics and operations to simple balance sheet, cash flow, and income statements. In the text, results are discussed for the total fleet, the Gulf shrimp fleet, the active Gulf shrimp fleet, and the inactive Gulf shrimp fleet. Additional results for shrimp vessels grouped by state, by vessel characteristics, by landings volume, and by ownership structure are available in the appendices. The general conclusion of this report is that the financial and economic situation is bleak for the average vessels in most of the categories that were evaluated. With few exceptions, cash flow for the average vessel is positive while the net revenue from operations and the “profit” are negative. With negative net revenue from operations, the economic return for average shrimp vessels is less than zero. Only with the help of government payments does the average owner just about break even. In the short-term, this will discourage any new investments in the industry. The financial situation in 2006, especially if it endures over multiple years, also is economically unsustainable for the average established business. Vessels in the active and inactive Gulf shrimp fleet are, on average, 69 feet long, weigh 105 gross tons, are powered by 505 hp motor(s), and are 23 years old. Three-quarters of the vessels have steel hulls and 59% use a freezer for refrigeration. The average market value of these vessels was $175,149 in 2006, about a hundred-thousand dollars less than the average original purchase price. The outstanding loans averaged $91,955, leading to an average owner equity of $83,194. Based on the sample, 85% of the federally permitted Gulf shrimp fleet was actively shrimping in 2006. Of these 386 active Gulf shrimp vessels, just under half (46%) were owner-operated. On average, these vessels burned 52,931 gallons of fuel, landed 101,268 pounds of shrimp, and received $2.47 per pound of shrimp. Non-shrimp landings added less than 1% to cash flow, indicating that the federal Gulf shrimp fishery is very specialized. The average total cash outflow was $243,415 of which $108,775 was due to fuel expenses alone. The expenses for hired crew and captains were on average $54,866 which indicates the importance of the industry as a source of wage income. The resulting average net cash flow is $16,225 but has a large standard deviation. For the population of active Gulf shrimp vessels we can state with 95% certainty that the average net cash flow was between $9,500 and $23,000 in 2006. The median net cash flow was $11,843. Based on the income statement for active Gulf shrimp vessels, the average fixed costs accounted for just under a quarter of operating expenses (23.1%), labor costs for just over a quarter (25.3%), and the non-labor variable costs for just over half (51.6%). The fuel costs alone accounted for 42.9% of total operating expenses in 2006. It should be noted that the labor cost category in the income statement includes both the actual cash payments to hired labor and an estimate of the opportunity cost of owner-operators’ time spent as captain. The average labor contribution (as captain) of an owner-operator is estimated at about $19,800. The average net revenue from operations is negative $7,429, and is statistically different and less than zero in spite of a large standard deviation. The economic return to Gulf shrimping is negative 4%. Including non-operating activities, foremost an average government payment of $13,662, leads to an average loss before taxes of $907 for the vessel owners. The confidence interval of this value straddles zero, so we cannot reject, with 95% certainty, that the population average is zero. The average inactive Gulf shrimp vessel is generally of a smaller scale than the average active vessel. Inactive vessels are physically smaller, are valued much lower, and are less dependent on loans. Fixed costs account for nearly three quarters of the total operating expenses of $11,926, and only 6% of these vessels have hull insurance. With an average net cash flow of negative $7,537, the inactive Gulf shrimp fleet has a major liquidity problem. On average, net revenue from operations is negative $11,396, which amounts to a negative 15% economic return, and owners lose $9,381 on their vessels before taxes. To sustain such losses and especially to survive the negative cash flow, many of the owners must be subsidizing their shrimp vessels with the help of other income or wealth sources or are drawing down their equity. Active Gulf shrimp vessels in all states but Texas exhibited negative returns. The Alabama and Mississippi fleets have the highest assets (vessel values), on average, yet they generate zero cash flow and negative $32,224 net revenue from operations. Due to their high (loan) leverage ratio the negative 11% economic return is amplified into a negative 21% return on equity. In contrast, for Texas vessels, which actually have the highest leverage ratio among the states, a 1% economic return is amplified into a 13% return on equity. From a financial perspective, the average Florida and Louisiana vessels conform roughly to the overall average of the active Gulf shrimp fleet. It should be noted that these results are averages and hence hide the variation that clearly exists within all fleets and all categories. Although the financial situation for the average vessel is bleak, some vessels are profitable. (PDF contains 101 pages)

Experimental investigation of Very-High-Cycle Fatigue behavior for a structural steel

Very-High-Cycle Fatigue (VHCF) test for a medium carbon structural steel (40Cr) has been performed and a stepwise S-N curve was obtained by employing cantilever-type rotary bending fatigue machine with hourglass shape specimen. The S-N curve was well explained as a combination of curves for surface-induced fracture and interior inclusion-induced fracture with fish-eye patterns. The morphology of the fish-eye pattern was illustrated in order to clarify subsurface crack initiation and propagation behavior.

Torsion fracture behavior of drawn pearlitic steel wires with different heat treatments

In this paper, torsion fracture behavior of drawn pearlitic steel wires with different heat treatments was investigated. Samples with different heat treatments was investigated. Samples with different heat treatment conditions were subjected to torsion and tensile tests. The shear strain along the torsion sample after fracture was measured. Fracture surface of wires was examined by Scanning Electron Microscopy. In addition, the method of Differential Scanning Calorimetry was used to characterize the thermodynamic process in the heat treatment. A numerical simulation via finite element method on temperature field evolution for the wire during heat treatment process was performed. The results show that both strain aging and recovery process occur in the material within the temperature range between room temperature and 435 degrees C. It was shown that the ductility measured by the number of twists drops at short heating times and recovers after further heating in the lead bath of 435 degrees C. On the other hand, the strenght of the wire increases at short heating times and decreases after further heating. The microstructure inhomogeneity due to short period of heat treatment, coupled with the gradient characteristics of shear deformation during torsion results in localized shear deformation of the wire. In this situation, shear cracks nucleate between lamella and the wire breaks with low number of twists.

Mechanical properties and constitutive relationships of 30CrMnSiA steel heated at high rate

In this paper, the mechanical behavior of 30CrMnSiA steel after heating at a high rate are investigated experimentally and theoretically, including a detailed discussion of the effects of strain rate and temperature. Two constitutive models are presented to describe the mechanical response of this material after heating at a high rate, and verified by experimental results. (C) 2007 Elsevier B.V. All rights reserved.