Roundabout design and cycling safety

Roundabouts reduce the frequency and severity of motor vehicle crashes and therefore the number installed has increased dramatically in the last 20 years in many countries. However, the safety impacts of roundabouts for bicycle riders are a source of concern, with many studies reporting lower injury reductions for cyclists than car occupants. This paper summarises the results of a project undertaken to provide guidance on how cyclist safety could be improved at existing roundabouts in Queensland, Australia, where cyclist crashes have been increasing and legislation gives motor vehicles priority over cyclists and pedestrians at roundabouts. The review of international roundabout design guidelines identified two schools of design: tangential roundabouts (common in English-speaking countries, including Australia), which focus on minimising delay to motor vehicles, and radial roundabouts (common in continental Europe), which focus on speed reduction and safety. While it might be expected that radial roundabouts would be safer for cyclists, there have been no studies to confirm this view. Most guidelines expect cyclists to act as vehicle traffic in single-lane, typically low-speed, roundabouts. Some jurisdictions do not permit cyclists to travel on multi-lane roundabouts, and recommend segregated bicycle facilities because of their lowest crash risk for cyclists. Given that most bicycle-vehicle crashes at roundabouts involve an entering vehicle and a circulating cyclist, the greatest challenges appear to be reducing the speed of motor vehicles on the approach/entry to roundabouts and other ways of maximizing the likelihood that cyclists will be seen. Lower entry speeds are likely to underpin the greater safety of compact roundabouts for cyclists and, conversely, the higher than expected crash rates at two-lane roundabouts. European research discourages the use of bike lanes in roundabouts which position cyclists at the edge of the road and contributes to cyclists being less likely to be noticed by drivers.

Engaging expert contractors: The work health and safety obligations of the business or undertaking

This article examines the legal principles governing the statutory work health and safety general duties of principals who engage expert contractors to carry out work beyond the expertise of the principal. The article examines recent case law in which superior courts accepted the principal’s argument that the engagement of the expert contractor was sufficient to discharge the principal’s statutory work health and safety general duty. It then reframes the debate within the principles of systematic work health and safety management, and key provisions in the harmonised Work Health and Safety Acts—the primary duty of care; the key underpinning principles; the positive and proactive officer’s duty; and the horizontal duty of consultation, cooperation and coordination. It argues that it is likely that courts examining the issue of the principal’s work health and safety obligations under the harmonised Work Health and Safety Acts will require principals to do more to actively manage the work of expert contractors to ensure the health and safety of all workers and others potentially affected by the work.

Toward a model for forming psychological safety climate in construction project management

The nature of construction projects and their delivery exposes participants to accidents and dangers. Safety climate serves as a frame of reference for employees to make sense of safety measures in the workplace and adapt their behaviors. Though safety climate research abounds, fewer efforts are made to investigate the formation of a safety climate. An effort to explore forming psychological safety climate, an operationalization of safety climate at the individual level, is an appropriate starting point. Taking the view that projects are social processes, this paper develops a conceptual framework of forming the psychological safety climate, and provides a preliminary validation. The model suggests that management can create the desired psychological safety climate by efforts from structural, perceptual, interactive, and cultural perspectives. Future empirical research can be built on the model to provide a more comprehensive and coherent picture of the determinants of safety climate.

Transformerless PV inverters - recent test results and a discussion of DC current injection and safety issues

With the variety of PV inverter types and the number of transformerless PV inverters on the Australian market increasing, we revisit some of the issues associated with these topologies. A recent electric shock incident in Queensland (luckily without serious outcome) associated with a transformerless PV system, highlights the need for earthing PV array structures and PV module frames to prevent capacitive leakage currents causing electric shock. The presented test results of the relevant voltages associated with leakage currents of five transformerless PV inverters stress this requirement, which is currently being addressed by both the Clean Energy Council and Standards Australia. DC current injection tests were performed on the same five inverters and were used to develop preliminary recommendations for a more meaningful DC current test procedure for AS4777 Part 2. The test circuit, methodology and results are presented and discussed. A notable temperature dependency of DC current injections with three of the five inverters suggests that DC current injection should be tested at high and low internal inverter temperatures whereas the power dependency noted only for one inverter does not seem to justify recommendations for a (rather involved) standard test procedure at different power levels.

Individual differences in the processing of punishment and reward cues : an application to road safety messages

This thesis examined the extent to which individual differences, as conceptualised by the revised Reinforcement Sensitivity Theory, influenced young drivers' information processing and subsequent acceptance of anti-speeding messages. Using a multi-method approach, the findings highlighted the utility of combining objective measures (a cognitive response time task and electroencephalography) with self-report measures to assess message processing and message acceptance, respectively. This body of research indicated that responses to anti-speeding messages may differ depending on an individual's personality disposition. Overall, the research provided further insight into the development of message strategies to target high risk drivers.

Improving safety communication of ethnic minorities in the construction industry of Hong Kong

The construction workforce in Hong Kong is experiencing a severe ageing problem and labour shortage. One initiative to enhance the supply of manpower is to assist ethnic minorities joining the industry. It is foreseeable that the percentage of ethnic minorities in the construction workforce will keep increasing. Statistics show that ethnic minorities were nearly 30% more likely to have work-related injuries than local workers in some developed countries. However, official statistics on the safety of ethnic minorities are not available in Hong Kong. A search in newspaper archive revealed that ethnic minorities in the construction industry of Hong Kong are subjected to higher fatality rate than local workers, just as is the case in many developed countries. This reflects that the safety of ethnic minorities has not received the attention it rightly deserves. Safety communication has been one of the key factors leading to accidents. Safety communication barriers of ethnic minorities impede them from receiving safety training and acquiring safety information effectively. Research towards improving the safety communication of ethnic minorities in the construction industry of Hong Kong becomes more urgent. This paper will provides an initial report on a research project which focuses on improving the safety communication of ethnic minorities in the construction industry of Hong Kong. Quantitative and qualitative research methods including Social Network Analysis (SNA) applied in conducting the research are first discussed. Preliminary statistics of construction accidents related to ethnic minorities in Hong Kong are then presented.

The role of university research centres in building road safety capacity : implications for China

In recent decades, highly motorised countries, such as Australia, have witnessed significant improvements in population health through reductions in fatalities and injuries from road traffic crashes. In Australia, concerted efforts have been made to reduce the road trauma burden since road fatalities reached their highest level in in the early 1970s. Since that time, many improvements have been made drawing on various disciplines to reduce the trauma burden (e.g., road and vehicle design, road user education, traffic law enforcement practices and enforcement technologies). While road fatalities have declined significantly since the mid-1970s, road trauma remains a serious public health concern in Australia. China has recently become the largest car market in the world (Ma, Li, Zhou, Duan, & Bishai, 2012). This rapid motorisation has been accompanied by substantial expansion of the road network as well as a large road trauma burden. Road traffic injuries are a major cause of death in China, reported as accounting for one third of all injury-deaths between 2002 and 2006 (Ma et al., 2012). In common with Australia, China has experienced a reported decline in fatalities since 2002 (see Hu, Wen & Baker, 2008). However, there remains a strong need for action in this area as rates of motorisation continue to climb in China. In Australia, a wide range of organisations have contributed to the improvements in road safety including government agencies, professional organisations, advocacy groups and research centres. In particular, Australia has several highly regarded and multi-disciplinary, university-based research centres that work across a range of road safety fields, including engineering, intelligent transportation systems, the psychology of road user behaviour, and traffic law enforcement. Besides conducting high-quality research, these centres fulfil an important advocacy role in promoting safer road use and facilitating collaborations with government and other agencies, at both the national and international level. To illustrate the role of these centres, an overview will be provided of the Centre for Accident Research and Road Safety-Queensland (CARRS-Q), which was established in 1996 and has gone on to become a recognised world-leader in road safety and injury prevention research. The Centre’s research findings are used to provide evidence-based recommendations to government and have directly contributed to promoting safer road use in Australia. Since 2006, CARRS-Q has also developed strong collaborative links with various universities and organisations in China to assist in building understanding, connections and capacity to assist in reducing the road trauma burden. References Hu, G., Wen, M., Baker, T. D., & Baker, S. P. (2008). Road-traffic deaths in China, 1985–2005: threat and opportunity. Injury Prevention, 14, 149-153. Ma, S., Li, Q., Zhou, M., Duan, L., & Bishai, D. (2012). Road Traffic Injury in China: A Review of National Data Sources. Traffic Injury Prevention, 13(S1), 57-63.

Effects of different surfaces on the perception of prey-generated noise by the Indian false vampire bat Megaderma lyra.

The low- and high-frequency components of a rustling sound, created when prey (freshly killed frog) was jerkily pulled on dry and wet sandy floors and asbestos, were recorded and played back to individual Indian false vampire bats (Megaderma lyra). Megaderma lyra responded with flight toward the speakers and captured dead frogs, that were kept as reward. The spectral peaks were at 8.6, 7.1 and 6.8 kHz for the low-frequency components of the sounds created at the dry, asbestos and wet floors, respectively. The spectral peaks for the high-frequency sounds created on the respective floors were at 36.8,27.2 and 23.3 kHz. The sound from the dry floor was more intense than that of from the other two substrata. Prey movements that generated sonic or ultrasonic sounds were both sufficient and necessary for the bats to detect and capture prey. The number of successful prey captures was significantly greater for the dry floor sound, especially to its high-frequency components. Bat-responses were low to the wet floor and moderate to the asbestos floor sounds. The bats did not respond to the sound of unrecorded parts of the tape. Even though the bats flew toward the speakers when the prey generated sounds were played back and captured the dead frogs we cannot rule out the possibility of M. lyra using echolocation to localize prey. However, the study indicates that prey that move on dry sandy floor are more vulnerable to predation by M. lyra.

Incorporation of road safety into road management systems

Road collisions negatively affect the lives of hundreds of Canadians per year. Unfortunately, safety has been typically neglected from management systems. It is common to find that a great deal of effort has been devoted to develop and implement systems capable of achieving and sustaining good levels of condition. It is relatively recent that road safety has become an important objective. Managing a network of roads is not an easy task; it requires long, medium and short term plans to maintain, rehabilitate and upgrade aging assets, reduce and mitigate accident exposure, likelihood and severity. This thesis presents a basis for incorporating road safety into road management systems; two case studies were developed; one limited by available data and another from sufficient information. A long term analysis was used to allocate improvements for condition and safety of roads and bridges, at the network level. It was confirmed that a safety index could be used to obtain a first cut model; meanwhile potential for improvement which is a difference between observed and predicted number of accidents was capable of capturing the degree of safety of individual segments. It was found that the completeness of the system resulted in savings because of the economies obtained from trade-off optimization. It was observed that safety improvements were allocated at the beginning of the analysis in order to reduce the extent of issues, which translated into a systematic reduction of potential for improvement up to a point of near constant levels, which were hypothesized to relate to those unavoidable collisions from human error or vehicle failure.

Risk perception and the public acceptance of drones

Unmanned aircraft, or drones, are a rapidly emerging sector of the aviation industry. There has been limited substantive research, however, into the public perception and acceptance of drones. This paper presents the results from two surveys of the Australian public designed to investigate (a) whether the public perceive drones to be riskier than existing manned aviation, (b) whether the terminology used to describe the technology influences public perception, and (c) what the broader concerns are that may influence public acceptance of the technology. We find that the Australian public currently hold a relatively neutral attitude towards drones. Respondents did not consider the technology to be overly unsafe, risky, beneficial, or threatening. Drones are largely viewed as being of comparable risk to that of existing manned aviation. Further, terminology had a minimal effect on the perception of the risks or acceptability of the technology. The neutral response is likely due to a lack of knowledge about the technology, which was also identified as the most prevalent public concern as opposed to the risks associated with its use. Privacy, military use and misuse (e.g., terrorism) were also significant public concerns. The results suggest that society is yet to form an opinion of drones. As public knowledge increases, the current position is likely to change. Industry communication and media coverage will likely influence the ultimate position adopted by the public, which can be difficult to change once established.

Driven by distraction: Investigating the effects of anxiety on driving performance using the Attentional Control Theory

This study investigates the effects of trait anxiety on self-reported driving behaviours through its negative impacts on Central Executive functions. Following a self-report study that found trait anxiety to be significantly related to driving behaviours, the present study extended the predictions of Eysenck and Calvo’s Attentional Control Theory, proposing that anxiety affects driving behaviours, in particular driving lapses, through its impact across the Central Executive. Seventy-five Australian drivers participated in the study, completing the Parametric Go/No-Go and n-back tasks, as well as the State-Trait Anxiety Inventory and the Driving Behaviour Questionnaire. While both trait anxiety and processing efficiency of the Central Executive was found to significantly predict driving lapses, trait anxiety remained a strong predictor of driving lapses after processing efficiency was controlled for. It is concluded that while processing efficiency of the central Executive is a key determinant of driving lapses, another Central Executive function that is closer to the driving lapses in the trait anxiety – driving lapses relationship may be needed. Suggestions regarding how to improve future trait anxiety – driving behaviours research are discussed.

Competitive advantage through safety compliance : smaller firm responses to changes in the Australian occupational health and safety regulatory context

Smaller firms are often viewed as resistant to regulation due to cost burdens. However, evidence indicates that for some compliance is beneficial under certain conditions. Drawing on data on attitudes and responses of smaller firm owner-managers to changes in Australia’s harmonising work health and safety context we report on smaller firms’ responses to these changes. Despite uncertainty due to incomplete harmonisation, many owner-managers viewed safety compliance as important and necessary to do business. Those with negative views still linked positive safety performance to business outcomes. We categorise smaller firms’ responses and in this sample most are Positive Responders. We suggest ways forward for policy-makers to support smaller firms in complying with occupational health and safety regulation.

Development of a flexible design approach for the deflection zone behind road safety barriers

Flexible design practices broadly permit that design values outside the normal range can be accepted as appropriate for a site-specific context providing that the risk is evaluated and is tolerable. Execution of flexible design demands some evaluation of risk. In restoration projects, it may be the case that an immovable object exists within the zone of the expected deflection of a road safety barrier system. Only by design exception can the situation be determined to be acceptable. However, the notion of using flexible design for road safety barrier design is not well developed. The existence of a diminishing return relationship between safety benefits and provision of increased clear zone has been established previously. This paper proposes that a similar rationale might reasonably apply for the deflection zone behind road safety barriers and describes how the risk associated with road safety barriers might be quantified in order that defensible road safety barrier design can exist below the lower bounds of normal design standards. As such, the methodology described in this paper may provide some basis to enable road authorities to make informed design decisions, particularly for restoration, or “Brownfield”, projects.

Traffic safety at road-rail level crossings using a driving simulator and traffic simulation

A number of Intelligent Transportation Systems (ITS) were used with an advanced driving simulator to assess its influence on driving behavior. Three types of ITS interventions namely, Video in-vehicle (ITS1), Audio in-vehicle (ITS2), and On-road flashing marker (ITS3) were tested. Then, the results from the driving simulator were used as inputs for a developed model using a traffic micro-simulation (Vissim 5.4) in order to assess the safety interventions. Using a driving simulator, 58 participants were required to drive through a number of active and passive crossings with and without an ITS device and in the presence or absence of an approaching train. The effect of driver behavior changing in terms of speed and compliance rate was greater at passive crossings than at active crossings. The difference in speed of drivers approaching ITS devices was very small which indicates that ITS helps drivers encounter the crossings in a safer way. Since the current traffic simulation was not able to replicate a dynamic speed change or a probability of stopping that varies based on different ITS safety devices, some modifications of the current traffic simulation were conducted. The results showed that exposure to ITS devices at active crossings did not influence the drivers’ behavior significantly according to the traffic performance indicators used, such as delay time, number of stops, speed, and stopped delay. On the other hand, the results of traffic simulation for passive crossings, where low traffic volumes and low train headway normally occur, showed that ITS devices improved overall traffic performance.