Catalytic oxidation of alcohols using molecular oxygen mediated by poly(ethylene glycol)-supported nitroxyl radicals

The selective catalytic oxidation of alcohols over a mixture of copper(l) chloride and a number of linear 'linker-less' or 'branched' poly(ethylene glycol)-supported nitroxyl radicals of the 2,2,6,6-tetramethyl-piperidine-1-oxyl (TEMPO) family as a catalyst system has been investigated in the presence of molecular oxygen in a batch reactor. It is found that the activity profile of the polymer-supported nitroxyl radicals is in good agreement with that of low-molecular weight nitroxyl catalysts, for example, allylic and benzylic alcohols are oxidised faster than aliphatic alcohols. The oxidations can be tuned to be highly selective such that aldehydes are the only oxidation products observed in the oxidation of primary alcohols and the oxidations of secondary alcohols yield the corresponding ketones. A strong structural effect of the polymeric nitroxyl species on catalytic activity that is dependent upon their spatial orientation of the nitroxyl radicals is particularly noted. The new soluble macromolecular catalysts can be recovered readily from the reaction mixture by solvent precipitation and filtration. In addition, the recycled catalysts demonstrate a similar selectivity with only a small decrease in activity compared to the fresh catalyst even after five repetitive cycles. (c) 2005 Elsevier B.V. All rights reserved.

Micelle-hosted bimetallic Pd-Ru nanoparticle for in situ catalytic hydrogenation in supercritical CO2

Bimetallic Pd-Ru nanoparticles of different elemental ratios are prepared via in situ reduction of their simple salts in reverse micelles in supercritical carbon dioxide (scCO(2)). The optimised Pd:Ru (1: 1) nanoparticle shows the highest activity for hydrogenation of functionalised alkene under mild conditions, which can be easily recycled under the reaction conditions without use of organic solvent. (c) 2006 Elsevier B.V. All rights reserved.

Endothelin-converting enzyme-1 regulates trafficking and signalling of the neurokinin 1 receptor in endosomes of myenteric neurones

Neuropeptide signalling at the plasma membrane is terminated by neuropeptide degradation by cell-surface peptidases, and by beta-arrestin-dependent receptor desensitization and endocytosis. However, receptors continue to signal from endosomes by beta-arrestin-dependent processes, and endosomal sorting mediates recycling and resensitization of plasma membrane signalling. The mechanisms that control signalling and trafficking of receptors in endosomes are poorly defined. We report a major role for endothelin-converting enzyme-1 (ECE-1) in controlling substance P (SP) and the neurokinin 1 receptor (NK(1)R) in endosomes of myenteric neurones. ECE-1 mRNA and protein were expressed by myenteric neurones of rat and mouse intestine. SP (10 nM, 10 min) induced interaction of NK(1)R and beta-arrestin at the plasma membrane, and the SP-NK(1)R-beta-arrestin signalosome complex trafficked by a dynamin-mediated mechanism to ECE-1-containing early endosomes, where ECE-1 can degrade SP. After 120 min, NK(1)R recycled from endosomes to the plasma membrane. ECE-1 inhibitors (SM-19712, PD-069185) and the vacuolar H(+)ATPase inhibitor bafilomycin A(1), which prevent endosomal SP degradation, suppressed NK(1)R recycling by >50%. Preincubation of neurones with SP (10 nM, 5 min) desensitized Ca(2+) transients to a second SP challenge after 10 min, and SP signals resensitized after 60 min. SM-19712 inhibited NK(1)R resensitization by >90%. ECE-1 inhibitors also caused sustained SP-induced activation of extracellular signal-regulated kinases, consistent with stabilization of the SP-NK(1)R-beta-arrestin signalosome. By degrading SP and destabilizing endosomal signalosomes, ECE-1 has a dual role in controlling endocytic signalling and trafficking of the NK(1)R: promoting resensitization of G protein-mediated plasma membrane signalling, and terminating beta-arrestin-mediated endosomal signalling.

Endothelin-converting enzyme 1 degrades neuropeptides in endosomes to control receptor recycling

Neuropeptide signaling requires the presence of G protein-coupled receptors (GPCRs) at the cell surface. Activated GPCRs interact with beta-arrestins, which mediate receptor desensitization, endocytosis, and mitogenic signaling, and the peptide-receptor-arrestin complex is sequestered into endosomes. Although dissociation of beta-arrestins is required for receptor recycling and resensitization, the critical event that initiates this process is unknown. Here we report that the agonist availability in the endosomes, controlled by the membrane metalloendopeptidase endothelin-converting enzyme 1 (ECE-1), determines stability of the peptide-receptor-arrestin complex and regulates receptor recycling and resensitization. Substance P (SP) binding to the tachykinin neurokinin 1 receptor (NK1R) induced membrane translocation of beta-arrestins followed by trafficking of the SP-NK1R-beta-arrestin complex to early endosomes containing ECE-1a-d. ECE-1 degraded SP in acidified endosomes, disrupting the complex; beta-arrestins returned to the cytosol, and the NK1R, freed from beta-arrestins, recycled and resensitized. An ECE-1 inhibitor, by preventing NK1R recycling in endothelial cells, inhibited resensitization of SP-induced inflammation. This mechanism is a general one because ECE-1 similarly regulated NK3R resensitization. Thus, peptide availability in endosomes, here regulated by ECE-1, determines the stability of the peptide-receptor-arrestin complex. This mechanism regulates receptor recycling, which is necessary for sustained signaling, and it may also control beta-arrestin-dependent mitogenic signaling of endocytosed receptors. We propose that other endosomal enzymes and transporters may similarly control the availability of transmitters in endosomes to regulate trafficking and signaling of GPCRs. Antagonism of these endosomal processes represents a strategy for inhibiting sustained signaling of receptors, and defects may explain the tachyphylaxis of drugs that are receptor agonists.

Ubiquitin-dependent down-regulation of the neurokinin-1 receptor

Transient stimulation with substance P (SP) induces endocytosis and recycling of the neurokinin-1 receptor (NK(1)R). The effects of sustained stimulation by high concentrations of SP on NK(1)R trafficking and Ca(2+) signaling, as may occur during chronic inflammation and pain, are unknown. Chronic exposure to SP (100 nm, 3 h) completely desensitized Ca(2+) signaling by wild-type NK(1)R (NK(1)Rwt). Resensitization occurred after 16 h, and cycloheximide prevented resensitization, implicating new receptor synthesis. Lysine ubiquitination of G-protein-coupled receptors is a signal for their trafficking and degradation. Lysine-deficient mutant receptors (NK(1)RDelta5K/R, C-terminal tail lysines; and NK(1)RDelta10K/R, all intracellular lysines) were expressed at the plasma membrane and were functional because they responded to SP by endocytosis and by mobilization of Ca(2+) ions. SP desensitized NK(1)Rwt, NK(1)RDelta5K/R, and NK(1)RDelta10K/R. However, NK(1)RDelta5K/R and NK(1)RDelta10K/R resensitized 4-8-fold faster than NK(1)Rwt by cycloheximide-independent mechanisms. NK(1)RDelta325 (a naturally occurring truncated variant) showed incomplete desensitization, followed by a marked sensitization of signaling. Upon labeling receptors in living cells using antibodies to extracellular epitopes, we observed that SP induced endocytosis of NK(1)Rwt, NK(1)RDelta5K/R, and NK(1)RDelta10K/R. After 4 h in SP-free medium, NK(1)RDelta5K/R and NK(1)RDelta10K/R recycled to the plasma membrane, whereas NK(1)Rwt remained internalized. SP induced ubiquitination of NK(1)Rwt and NK(1)RDelta5K/R as determined by immunoprecipitation under nondenaturing and denaturing conditions and detected with antibodies for mono- and polyubiquitin. NK(1)RDelta10K/R was not ubiquitinated. Whereas SP induced degradation of NK(1)Rwt, NK(1)RDelta5K/R and NK(1)RDelta10K/R showed approximately 50% diminished degradation. Thus, chronic stimulation with SP induces ubiquitination of the NK(1)R, which mediates its degradation and down-regulation.

The efficacy of potassium sorbate-coated packaging to control postharvest gray mold in raspberries, blackberries, and blueberries

The aim of this work is to build on the success of in vitro studies of an active packaging, produced by coating the surface of post-consumer recycled polyethylene terephthalate (PCRPET) package with an aqueous silicone solution (2%, v/v) containing an antifungal agent (potassium sorbate, KS). Antifungal efficacy was evaluated, in vivo, during the storage of raspberries, blackberries and blueberries by examining their shelf life extension. The packaging effectively delayed the growth of Botrytis by extending its lag-phase, which, in turn, extended the shelf life of the berries by up to 3d. Among the three berries tested, the packaging proved to be more advantageous in the case of raspberries, due to their physiological characteristics and shorter shelf life. Based on sensory panel evaluations, it was shown that the coating, containing KS, did not influence the packaging appearance and transparency, and the fruit did not suffer from any off-flavor development.

Developments in the quality of treated greywater supplies for buildings, and associated user perception and acceptance

A manufactured aeration and nanofiltration MBR greywater system was tested during continuous operation at the University of Reading, to demonstrate reliability in delivery of high quality treated greywater. Its treatment performance was evaluated against British Standard criteria [BSI (Greywater Systems—Part 1 Code of Practice: BS8525-1:2010. BS Press, 2010); (Greywater Systems—Part 2 Domestic Greywater Treatment, Requirements and Methods: BS 8525-2:2011. BS Press, 2011)]. The low carbon greywater recycling technology produced excellent analytical results as well as consistency in performance. User acceptance of such reliably treated greywater was then evaluated through user perception studies. The results inform the potential supply of treated greywater to student accommodation. Out of 135 questionnaire replies, 95% demonstrated a lack of aversion in one or more attributes, to using treated, recycled greywater.

Catalytic hydrodechlorination of chlorobenzene over supported palladium catalyst in buffered medium

The catalytic hydrodechlorination (HDC) reaction, which is an attractive abatement process for chlorinated organic wastes, was studied over a magnetically recoverable supported Pd(0) catalyst. We investigated the most favorable reaction conditions under which to obtain the highest substrate conversion rates while preserving the catalyst properties and morphology. Sodium hydroxide, triethylamine and buffered solutions were used as proton scavengers in the HDC of chlorobenzene under mild conditions. It was observed that sodium hydroxide caused corrosion of the silica support, triethylamine in 2-propanol preserved the morphology of the catalyst which could be recycled for up to five successive H DC reactions, and aqueous buffer solutions preserved the catalyst morphology and the catalytic activity for up to four successive HDC reactions. The use of buffer solutions to neutralize the HCl formed during the HDC reaction is an interesting, less aggressive, alternative approach to HDC reactions. (C) 2010 Elsevier B.V. All rights reserved.

Microwave-Assisted Derivatization of Cellulose in an Ionic Liquid: An Efficient, Expedient Synthesis of Simple and Mixed Carboxylic Esters

Microwave (MW)-assisted cellulose dissolution in ionic liquids (ILs) has routinely led either to incomplete biopolymer solubilization, or its degradation. We show that these problems can be avoided by use of low-energy MW heating, coupled with efficient stirring. Dissolution of microcrystalline cellulose in the IL 1-allyl-3-methylimidazolium chloride has been achieved without changing its degree of polymerization; regenerated cellulose showed pronounced changes in its index of crystallinity, surface area, and morphology. MW-assisted functionalization of MCC by ethanoic, propanoic, butanoic, pentanoic, and hexanoic anhydrides has been studied. Compared with conventional heating, MW irradiation has resulted in considerable decrease in dissolution and reaction times. The value of the degree of substitution (DS) was found to be DS(ethanoate) > DS(propanoate) > DS(butanoate). The values of DS(pentanoate) and DS(hexanoate) were found to be slightly higher than DS(ethanoate). This surprising dependence on the chain length of the acylating agent has been reported before, but not rationalized. On the basis of the rate constants and activation parameters of the hydrolysis of ethanoic, butanoic, and hexanoic anhydrides in aqueous acetonitrile (a model acyl transfer reaction), we suggest that this result may be attributed to the balance between two opposing effects, namely, steric crowding and (cooperative) hydrophobic interactions between the anhydride and the cellulosic surface, whose lipophilicity has increased, due to its partial acylation. Four ethanoate-based mixed esters were synthesized by the reaction with a mixture of the two anhydrides; the ethanoate moiety predominated in all products. The DS is reproducible and the IL is easily recycled. (C) 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 134-143, 2010

The role of oxygen in the interaction of emeraldine base polyaniline with Cu(II) or Fe(III) ions in NMP solution

The influence of molecular oxygen in the interactions of emeraldine base form of polyaniline (EB-PANI) with Fe(III) or Cu(II) ions in 1-methyl-2-pyrrolidinone (NMP) solutions has been investigated by UV-vis-NIR, resonance Raman and electron paramagnetic resonance (EPR) spectroscopies. Through the set of spectroscopic results it was possible to rationalize the role Of O(2) and to construct a scheme of preferential routes occurring in the interaction of EB-PANI with Fe(III) or Cu(II). Solutions of 4.0 mmol L(-1) EB-PANI with 0.8, 2.0 and 20 mmol L(-1) Fe(III) or Cu(II) ions in NMP were investigated and the main observed reactions were EB-PANI oxidation to pernigraniline (PB-PANI) and EB-PANI doping process by pseudo-protonation, or by a two-step redox process. In the presence Of O(2), PB-PANI is observed in all Fe(III)/EB solutions and EB-PANI doping only occurs in solutions with high Fe(III) concentrations through pseudo-protonation. On the other hand, emeraldine salt (ES-PANI) is formed in all Fe(III)/EB solutions under N(2) atmosphere and, in this case, doping occurs both by the pseudo-protonation and two-step redox mechanisms. In all Cu(II)/EB solutions PB-PANI is formed both in the presence and absence of O(2), and only for solutions with high Cu(II) concentrations doping process occurs in a very low degree. The most important result from EPR spectra was providing evidence for redox steps. The determined Cu(II) signal areas under oxygen are higher than under N(2) and, further. the initial metal proportions (1:2:20) are maintained in these spectra, indicating that Cu(I) formed are re-oxidized by O(2) and. so, Cu(II) ions are being recycled. Consistently, for the solutions prepared under nitrogen, the corresponding areas and proportions in the spectra are much lower, confirming that a partial reduction of Cu(II) ions actually occurs. (C) 2009 Elsevier B.V. All rights reserved.

Informationssäkerhet inom grafiska företag

The study shows the current need for security solutions concerning work with information in different areas.Investigations will show important solutions for printers’ needs to meet the increasingly harder demands forfast and safe digital communications. Important factors to be analyzed in the investigations are: access todifferent types of information, workers authority of information, access to the data base register internallyand externally, production solutions for an effective fault detection and data base solutions fororders and distribution.Planned and unplanned stops result in a standard of value in interruptions. Internal data bases areprotected by so-called “Fire Walls”, “Watch Dogs” and Virtual Private Networks. Offset plates are locked infor a definitive range of time. Subsequent destruction and remaining sheets are shredded and recycled. Alldocumentation is digital, in business control systems, which guarantees that no important documents arelying around in working places. Fault detection work is facilitated by the ability to fully track the order numberson incoming orders.

Efeitos da variação da carga por eixo, pressão de inflação e tipo de pneu na resposta elástica de um pavimento

O presente trabalho é uma análise experimental que procura investigar os efeitos dos fatores carga por eixo, pressão de inflação e tipo de pneu sobre o desempenho de pavimentos. Os dados e informações existentes sobre o quadro de cargas por eixo praticada pela frota de veículos pesados é razoável. A ação conjunta dos referidos fatores é ainda uma questão pouco explorada. Assim, para compensar a escassez de dados sobre pressão de inflação e tipo de construção de pneus utilizados na frota de carga, programou-se uma pesquisa de campo na rodovia estadual RS/240. As informações oriundas da pesquisa demonstram que há um acréscimo generalizado no valor da pressão dos pneus e um aumento de uso dos pneus de fabricação radial em relação aos pneus convencionais. Os dados de campo subsidiaram a programação de um experimento fatorial cruzado executado na Área de Pesquisas e Testes de Pavimentos da UFRGS/DAER. A variação dos níveis dos fatores deu-se através de um simulador linear de tráfego atuando sobre uma pista experimental com 20 m de comprimento por 3,5 m de largura. Tendo como resposta estrutural do pavimento a máxima deflexão superficial recuperável medida com uma viga Benkelmam, determinou-se como significantes os efeitos dos fatores carga por eixo e pressão de enchimento dos pneus. Os cálculos estatísticos indicam também que não há diferenças significativas entre os pneus tipo 9.00R20 e 9.00x20 e que todas interações não exercem efeitos significativos sobre a variável de resposta. Em seqüência, determinaram-se as áreas de contato do rodado duplo do simulador de tráfego com a superfície do pavimento ensaiado para as combinações dos níveis dos fatores. Pode-se, então, comparar área de contato medida com área circular calculada, considerada em muitos modelos de dimensionamento de pavimentos. Relacionou-se a variação da pressão de contato com a deflexão recuperável e procedeu-se uma comparação da mesma com a pressão de inflação nominal dos pneus. Apresenta-se um modelo de análise do desempenho do pavimento em função da carga por eixo e da pressão de inflação, nos limites do experimento. Os dados decorrentes do experimento viabilizaram a determinação dos Fatores de Equivalência de Cargas para os níveis dos fatores, considerando-se o pavimento ensaiado. Avaliou-se, via evolução das deflexões e dos Fatores de Equivalência de Cargas, a redução da vida do pavimento, obtendo-se, para a combinação de níveis mais críticos de carregamento, resultados significativos de até 88 % de redução. Propõe-se, por último, uma formulação para o Fator de Equivalência de Cargas que considere também a ação da pressão de inflação.

Uma avaliação técnico/econômica da reciclagem de revestimentos asfálticos a frio em usina em área urbana

Trata-se nesta dissertação do emprego da reciclagem a frio de revestimentos asfálticos em usina com a finalidade de aproveitamento como camada de revestimento em vias de tráfego leve e muito leve. São revistos os conceitos de dimensionamento de pavimentos e da dosagem de misturas asfálticas. Dá-se especial atenção ao valor do revestimento asfáltico recuperado e a relevância que a reciclagem tem sobre a redução do descarte de resíduos sólidos no meio ambiente. Identifica-se a importância do emprego da reciclagem sobre o comportamento da sociedade. A metodologia adotada tem por base uma revisão bibliográfica dos registros de trabalhos de reciclagem a frio realizados no Brasil e no exterior. Faz-se um relato dos procedimentos de caracterização dos materiais envolvidos e dos cuidados a serem observados para obter-se um produto final de qualidade. Estão aqui descritos os processos industriais de usinagem da mistura reciclada em plantas industriais fixas. É estabelecida uma proposta de definição da viabilidade econômica de emprego da reciclagem a frio em comparação com o revestimento asfáltico tradicional. Ao final são registrados temas a serem estudados visando tornar a reciclagem a frio de revestimentos asfálticos em usinas de áreas urbanas mais conhecida e considerada como alternativa para a melhoria da qualidade de vida nas cidades.

Gestão da inovação para a sustentabilidade ambiental: estudos de caso do desenvolvimento e difusão de produtos de consumo industrializados com materiais de fontes renováveis

O objetivo desta tese é identificar como ocorre a gestão da inovação de produto ambientalmente sustentável. Pelo método de estudo de caso e sob a perspectiva de três vertentes da teoria organizacional (estrutura do setor de negócios, visão baseada em recursos e visão relacional) foi realizada uma análise abrangente de como os condicionantes externos do ambiente competitivo, os condicionantes internos empresariais e os relacionamentos organizacionais impactaram no projeto de desenvolvimento e difusão de duas inovações de produto com atributos favoráveis à sustentabilidade ambiental: uma esponja de banho com fibras amazônicas e PET reciclado e um lava-louças líquido para o pronto-uso de fontes renováveis. Os dois casos apresentam marcantes diferenças em relação ao porte das empresas, às estruturas, competências e culturas organizacionais, à maturidade das respectivas plataformas tecnológicas de fontes renováveis e às abordagens utilizadas na gestão dos projetos de desenvolvimento de novo produto. Além disso, os dois casos são distintos na competitividade dos atributos de produto ambientais e funcionais em relação ao preço ante os produtos concorrentes. Apesar destas diferenças, construtos da visão relacional foram utilizados para identificar similaridades entre os dois estudos de caso na gestão da inovação. Redes informais internas realizaram uma inovação organizacional ao criarem um departamento de sustentabilidade, o qual realizou diagnósticos e recomendações para minimizar os riscos sócio-ambientais e regulatórios decorrentes do suprimento da fibra amazônica para a esponja de banho. E um relacionamento colaborativo complementou a inovação de produto e realizou inovações de marketing que proporcionaram o melhor desempenho na difusão do lava-louças pronto-uso de fontes renováveis no varejo. Portanto, apesar das diferenças nos condicionantes internos e externos, a gestão da inovação nos dois casos se utilizou de relacionamentos colaborativos a fim de gerar inovações empresariais que solucionaram as restrições ao processo de inovação de produto ambientalmente sustentável.

Ferramentas para análise dinâmica e estrutural de um reboque de linha leve

Neste trabalho é desenvolvida uma metodologia de projeto para identificar as regiões críticas da estrutura de um reboque de linha leve sendo tracionado em pavimentos do tipo rodovia de baixa qualidade e estrada secundária de muito baixa qualidade. Para tanto, são levantados alguns dados experimentais da estrutura, necessários para a aproximação e simulação dinâmica de um modelo simplificado. A excitação da base é realizada por atuadores que simulam as oscilações verticais de um perfil de estrada, a qual é definida de acordo com os estudos realizados por Dodds e Robson (1973). Isto permite a determinação de um histórico de carregamentos das regiões da estrutura do chassi sob a ação das molas da suspensão. Em seguida, é gerado um modelo estrutural simplificado do reboque em elementos finitos, chamado de global, no qual são determinadas as regiões sob ação das maiores tensões. Tendo identificada a região mais crítica da estrutura, é criado um modelo local desta parte, onde se pode observar a distribuição de tensões com mais detalhe, permitindo a identificação dos pontos de concentração de tensões. Desta forma, com a aplicação do método de análise global-local é possível a obtenção de resultados detalhados quanto aos esforços da estrutura com um menor custo computacional.