Estudo da sinterização de eletrólito sólido de céria dopada com gadolínia

Fuel cells are electrochemical devices that convert chemical energy in electrical energy by a reaction directly. The solid oxide fuel cell (SOFC) works in temperature between 900ºC up to 1000ºC, Nowadays the most material for ceramic electrolytes is yttria stabilized zirconium. However, the high operation temperature can produce problems as instability and incompatibility of materials, thermal degradation and high cost of the surround materials. These problems can be reduced with the development of intermediate temperature solid oxide fuel cell (IT-SOFC) that works at temperature range of 600ºC to 800ºC. Ceria doped gadolinium is one of the most promising materials for electrolytes IT-SOFC due high ionic conductivity and good compatibility with electrodes. The inhibition of grain growth has been investigated during the sintering to improve properties of electrolytes. Two-step sintering (TSS) is an interesting technical to inhibit this grain growth and consist at submit the sample at two stages of temperature. The first one stage aims to achieve the critical density in the initiating the sintering process, then the sample is submitted at the second stage where the temperature sufficient to continue the sintering without accelerate grain growth until to reach total densification. The goal of this work is to produce electrolytes of ceria doped gadolinium by two-step sintering. In this context were produced samples from micrometric and nanometric powders by two routes of two-step sintering. The samples were obtained with elevate relative density, higher than 90% using low energy that some works at the same area. The average grain size are at the range 0,37 μm up to 0,51 μm. The overall ionic conductivity is 1,8x10-2 S.cm and the activation energy is 0,76 eV. Results shown that is possible to obtain ceria-doped gadolinium samples by two-step sintering technique using modified routes with characteristics and properties necessary to apply as electrolytes of solid oxide fuel cell

Processamento e caracterização da blenda poli (metacrilato de metila) (PMMA) elastomerico e poli (tereftalato de etileno) (PET) pós-consumo

This work studied the immiscible blend of elastomeric poly(methyl methacrylate) (PMMA) with poly(ethylene terephthalate) (PET) bottle grade with and without the use of compatibilizer agent, poly(methyl methacrylate-co-glycidyl methacrylate - co-ethyl acrylate) (MGE). The characterizations of torque rheometry, melt flow index measurement (MFI), measuring the density and the degree of cristallinity by pycnometry, tensile testing, method of work essential fracture (EWF), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were performed in pure polymer and blends PMMA/PET. The rheological results showed evidence of signs of chemical reaction between the epoxy group MGE with the end groups of the PET chains and also to the elastomeric phase of PMMA. The increase in the concentration of PET reduced torque and adding MGE increased the torque of the blend of PMMA/PET. The results of the MFI also show that elastomeric PMMA showed lower flow and thus higher viscosity than PET. In the results of picnometry observed that increasing the percentage of PET resulted in an increase in density and degree crystallinity of the blends PMMA/PET. The tensile test showed that increasing the percentage of PET resulted in an increase in ultimate strength and elastic modulus and decrease in elongation at break. However, in the phase inversion, where the blend showed evidence of a co-continuous morphology and also, with 30% PET dispersed phase and compatibilized with 5% MGE, there were significant results elongation at break compared to elastomeric PMMA. The applicability of the method of essential work of fracture was shown to be possible for most formulations. And it was observed that with increasing elastomeric PMMA in the formulations of the blends there was an improvement in specific amounts of essential work of fracture (We) and a decrease in the values of specific non-essential work of fracture (βWp)

Desenvolvimento e caracterização de um compósito matriz metálica (CMM): aço EUROFER97 reforçado com Carbeto de Tântalo - TaC

Steel is an alloy EUROFER promising for use in nuclear reactors, or in applications where the material is subjected to temperatures up to 550 ° C due to their lower creep resistance under. One way to increase this property, so that the steel work at higher temperatures it is necessary to prevent sliding of its grain boundaries. Factors that influence this slip contours are the morphology of the grains, the angle and speed of the grain boundaries. This speed can be decreased in the presence of a dispersed phase in the material, provided it is fine and homogeneously distributed. In this context, this paper presents the development of a new material metal matrix composite (MMC) which has as starting materials as stainless steel EUROFER 97, and two different kinds of tantalum carbide - TaC, one with average crystallite sizes 13.78 nm synthesized in UFRN and another with 40.66 nm supplied by Aldrich. In order to improve the mechanical properties of metal matrix was added by powder metallurgy, nano-sized particles of the two types of TaC. This paper discusses the effect of dispersion of carbides in the microstructure of sintered parts. Pure steel powders with the addition of 3% TaC UFRN and 3% TaC commercial respectively, were ground in grinding times following: a) 5 hours in the planetary mill for all post b) 8 hours of grinding in the mill Planetary only for steel TaC powders of commercial and c) 24 hours in the conventional ball mill mixing the pure steel milled for 5 hours in the planetary mill with 3% TaC commercial. Each of the resulting particulate samples were cold compacted under a uniaxial pressure of 600MPa, on a cylindrical matrix of 5 mm diameter. Subsequently, the compressed were sintered in a vacuum furnace at temperatures of 1150 to 1250 ° C with an increment of 20 ° C and 10 ° C per minute and maintained at these isotherms for 30, 60 and 120 minutes and cooled to room temperature. The distribution, size and dispersion of steel and composite particles were determined by x-ray diffraction, scanning electron microscopy followed by chemical analysis (EDS). The structures of the sintered bodies were observed by optical microscopy and scanning electron accompanied by EDS beyond the x-ray diffraction. Initial studies sintering the obtained steel EUROFER 97 a positive reply in relation to improvement of the mechanical properties independent of the processing, because it is obtained with sintered microhardness values close to and even greater than 100% of the value obtained for the HV 333.2 pure steel as received in the form of a bar

Efeito da Gália como aditivo de sinterização em eletrólitos cerâmicos à base de céria sintetizados pelo método de complexação de cátions

Fuel cells are considered one of the most promising ways of converting electrical energy due to its high yield and by using hydrogen (as fuel) which is considered one of the most important source of clean energy for the future. Rare earths doped ceria has been widely investigated as an alternative material for the electrolyte of solid oxide fuel cells (SOFCs) due to its high ionic conductivity at low operating temperatures compared with the traditional electrolytes based on stabilized zirconia. This work investigates the effect of gallium oxide (Gallia) as a sintering aid in Eu doped ceria ceramic electrolytes since this effect has already been investigated for Gd, Sm and Y doped ceria electrolytes. The desired goal with the use of a sintering aid is to reduce the sintering temperature aiming to produce dense ceramics. In this study we investigated the effects on densification, microstructure and ionic conduction caused by different molar fraction of the dopants europium (10, 15 and 20%) and gallium oxide (0.3, 0.6 and 0.9%) in samples sintered at 1300, 1350 and 1450 0 C. Samaria (10 and 20%) doped ceria samples sintered between 1350 and 1450 °C were used as reference. Samples were synthesized using the cation complexation method. The ceramics powders were characterized by XRF, XRD and SEM, while the sintered samples were investigated by its relative density, SEM and impedance spectroscopy. It was showed that gallia contents up to 0.6% act as excellent sintering aids in Eu doped ceria. Above this aid content, gallia addition does not promote significant increase in density of the ceramics. In Ga free samples the larger densification were accomplished with Eu 15% molar, effect expressed in the microstructure with higher grain growth although reduced and surrounded by many open pores. Relative densities greater than 95 % were obtained by sintering between 1300 and 1350 °C against the usual range 1500 - 1600 0 C. Samples containing 10% of Sm and 0.9% of Ga reached 96% of theoretical density by sintering at 1350 0 C for 3h, a gain compared to 97% achieved with 20% of Sm and 1% of Ga co-doped cerias sintered at 1450 0 C for 24 h as described in the literature. It is found that the addition of gallia in the Eu doped ceria has a positive effect on the grain conductivity and a negative one in the grain boundary conductivity resulting in a small decrease in the total conductivity which will not compromise its application as sintering aids in ceria based electrolytes. Typical total conductivity values at 600 and 700 °C, around 10 and 30 mS.cm -1 respectively were reached in this study. Samples with 15% of Eu and 0.9 % of Ga sintered at 1300 and 1350 °C showed relative densities greater than 96% and total conductivity (measured at 700 °C) between 20 and 33 mS.cm -1 . The simultaneous sintering of the electrolyte with the anode is one of the goals of research in materials for SOFCs. The results obtained in this study suggest that dense Eu and Ga co-doped ceria electrolytes with good ionic conductivity can be sintered simultaneously with the anode at temperatures below 1350 °C, the usual temperature for firing porous anode materials

Estudo de adsorvente obtido de terras diatomáceas para remoção de metais pesados em águas produzidas: processamento, caracterização e dinâmica em leito fixo

The acceleration of industrial growth in recent decades on all continents aroused the interest of the companies to counter the impacts produced on the environment, spurred primarily by major disasters in the petroleum industry. In this context, the water produced is responsible for the largest volume of effluent from the production and extraction of oil and natural gas. This effluent has in its composition some critical components such as inorganic salts, heavy metals (Fe, Cu, Zn, Pb, Cd, ), presence of oil and chemicals added in the various production processes. In response to impact, have been triggered by research alternative adsorbent materials for water treatment and water produced, in order to removing oils and acids and heavy metals. Many surveys of diatomaceous earth (diatomite) in Brazil involve studies on the physico-chemical, mineral deposits, extraction, processing and applications. The official estimated Jazi are around 2.5 million tonnes, the main located in the states of Bahia (44%) and Rio Grande do Norte (37,4%). Moreover, these two states appear as large offshore producers, earning a prominent role in research of adsorbents such as diatomite for treatment of water produced. Its main applications are as an agent of filtration, adsorption of oils and greases, industrial load and thermal insulator. The objective of this work was the processing and characterization of diatomite diatomaceous earth obtained from the municipality of Macaíba-RN (known locally as tabatinga) as a low cost regenerative adsorbent for removal of heavy metals in the application of water produced treatment. In this work we adopted a methodology for batch processing, practiced by small businesses located in producing regions of Brazil. The characterization was made by X-ray diffraction (XRD), scanning electron microscopy (SEM) and specific surface area (BET). Research conducted showed that the improvement process used was effective for small volume production of diatomite concentrated. The diatomite obtained was treated by calcination at temperature of 900 oC for 2 hours, with and without fluxing Na2CO3 (4%), according to optimal results in the literature. Column adsorption experiments were conducted to percolation of the in nature, calcined and calcined fluxing diatomites. Effluent was used as a saline solution containing ions of Cu, Zn, Na, Ca and Mg simulating the composition of produced waters in the state of Rio Grande do Norte, Brazil. The breakthrough curves for simultaneous removal of copper ions and zinc as a result, 84.3% for calcined diatomite and diatomite with 97.3 % for fluxing. The calcined fluxing diatomite was more efficient permeability through the bed and removal of copper and zinc ions. The fresh diatomite had trouble with the permeability through the bed under the conditions tested, compared with the other obtained diatomite. The results are presented as promising for application in the petroleum industry

Processamento Inteligente de Sinais de Pressão e Temperatura Adquiridos Através de Sensores Permanentes em Poços de Petróleo

Originally aimed at operational objectives, the continuous measurement of well bottomhole pressure and temperature, recorded by permanent downhole gauges (PDG), finds vast applicability in reservoir management. It contributes for the monitoring of well performance and makes it possible to estimate reservoir parameters on the long term. However, notwithstanding its unquestionable value, data from PDG is characterized by a large noise content. Moreover, the presence of outliers within valid signal measurements seems to be a major problem as well. In this work, the initial treatment of PDG signals is addressed, based on curve smoothing, self-organizing maps and the discrete wavelet transform. Additionally, a system based on the coupling of fuzzy clustering with feed-forward neural networks is proposed for transient detection. The obtained results were considered quite satisfactory for offshore wells and matched real requisites for utilization

Implementação do algoritmo (RTM) para processamento sísmico em arquiteturas não convencionais

With the growth of energy consumption worldwide, conventional reservoirs, the reservoirs called "easy exploration and production" are not meeting the global energy demand. This has led many researchers to develop projects that will address these needs, companies in the oil sector has invested in techniques that helping in locating and drilling wells. One of the techniques employed in oil exploration process is the reverse time migration (RTM), in English, Reverse Time Migration, which is a method of seismic imaging that produces excellent image of the subsurface. It is algorithm based in calculation on the wave equation. RTM is considered one of the most advanced seismic imaging techniques. The economic value of the oil reserves that require RTM to be localized is very high, this means that the development of these algorithms becomes a competitive differentiator for companies seismic processing. But, it requires great computational power, that it still somehow harms its practical success. The objective of this work is to explore the implementation of this algorithm in unconventional architectures, specifically GPUs using the CUDA by making an analysis of the difficulties in developing the same, as well as the performance of the algorithm in the sequential and parallel version

Defumação da tilápia do Nilo (Oreochromis niloticus) inteira eviscerada e filé: aspectos referentes às características organolépticas, composição centesimal e perdas ocorridas no processamento

O objetivo do experimento foi avaliar o efeito da defumação da tilápia do Nilo (Oreochromis niloticus) inteira eviscerada e filé sobre as características organolépticas (aparência, aroma, cor, sabor, textura, teor de sal e aceitação geral), a porcentagem de perda de peso (PP) e composição centesimal. Foram comparados FP1 (peixe inteiro eviscerado, 5 horas de fumaça) e FP2 (filé, 4 horas de fumaça). Os peixes foram descamados, eviscerados, para obtenção de FP1 ou filetados por uma única pessoa, para obtenção de FP2, e então submetidos à salmouragem úmida (30%) e à defumação. O rendimento médio para FP1 e FP2 foi de 63,98 e 27,11%, respectivamente. O valor médio para porcentagem de perda de peso ocorrida na defumação para o filé (31,33%) foi superior ao peixe inteiro (27,04%). A análise sensorial revelou que o peixe inteiro teve melhor aceitação quanto ao sabor e teor de sal e não diferiu do filé quanto ao aroma, cor e textura. O processo de defumação reduziu o conteúdo de umidade e proporcionou aumento nos teores de proteína bruta, lipídios e cinzas. As perdas foram maiores para o filé, que apresentou maior teor de proteína bruta e menor teor de lipídios comparado ao peixe inteiro. Verificou-se também que o sabor do filé pode ser melhorado em função de uma correção na salmouragem.

Resíduos e subprodutos agroindustriais e grãos como substratos para produção do fungo entomapatogênico Lecanicillium lecanii

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Produção de Bipolaris euphorbiae em meios de cultura sólidos e líquidos obtidos de grãos e resíduos agroindustriais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Viabilidade in vitro de grãos de pólen de bacurizeiro - Clusiaceae

O bacurizeiro (Platonia insignis Mart.) é uma frutífera nativa da Amazônia, que apresenta alogamia acentuada e autoincompatibilidade esporofítica. A viabilidade in vitro tem sido utilizada para representar a capacidade potencial do pólen em completar o processo de fertilização O objetivo do presente trabalho foi estudar a viabilidade de polens de bacurizeiro por meio da germinação in vitro , por ser esta uma técnica em que o comportamento germinativo é semelhante in vivo . Os ensaios foram conduzidos em laboratório, em um delineamento inteiramente casualizado, analisados em esquema fatorial 2 x 3 x 4, em que: 2=formas de propagação (pé-franco e enxertada); 3=estágios da antese (pré-antese, antese e pós-antese), e 4=concentrações de sacarose (0; 7,5; 10 e 20%), com 10 repetições. Houve diferença significativa na germinação do pólen, sendo que, via polinização manual, o pólen deve ser coletado na antese, enquanto o melhor meio para a germinação in vitro é com 7,5 g de sacarose.

Efeito de períodos de semeadura e das condições de armazenamento sobre a qualidade de grãos de feijão para o cozimento

A conservação adequada pode manter as características do grão recém-colhido por mais tempo, assegurando o valor comercial do produto estocado. Assim, o objetivo deste trabalho foi avaliar o efeito de períodos de semeadura na qualidade de cozimento de grãos de feijão da cultivar TPS Nobre, quando armazenados em diferentes condições de temperatura, de umidade e tempo de estocagem. O delineamento experimental utilizado foi o inteiramente casualizado, com três repetições. Os tratamentos consistiram da combinação de três períodos de semeadura, com três ambientes de armazenamento e três tempos de armazenamento dos grãos (0, 3 e 6 meses). A interpretação dos resultados permitiu inferir que as porcentagens de grãos normais e de grãos duros revelaram comportamento diferenciado em função do ambiente e do tempo de armazenamento. Constatou-se maior porcentagem de grãos duros após seis meses de armazenamento, realizado sob temperatura média do ar de 12 °C e umidade relativa de 45%-50% e também quando os grãos foram resultantes de semeadura realizada tardiamente (21/10/03). A absorção de água e o tempo de cozimento dos grãos de feijão foram alterados em função do período de semeadura, das condições e do tempo de armazenamento, caracterizando a existência de efeitos da interação genótipos x ambientes na qualidade para o cozimento dos grãos. Sendo assim, maior ou menor tempo para a absorção de água ou para o cozimento podem ser requeridos em função da qualidade dos grãos no momento da colheita ou das condições de temperatura e de umidade de armazenamento.

Avaliação econômica e desempenho de machos e fêmeas Canchim em confinamento alimentados com dietas à base de silagem de milho e concentrado ou cana-de-açúcar e concentrado contendo grãos de girassol

Objetivou-se avaliar os efeitos do fornecimento de dietas com silagem de milho ou com cana-de-açúcar + grãos de girassol e a influência da condição sexual do animal sobre o desempenho de bovinos jovens em confinamento e os resultados econômicos desse sistema de produção. Foram utilizados 30 animais Canchim (dez machos não-castrados, dez machos castrados e dez novilhas), com 15 meses de idade e 289 kg de peso corporal (PC), mantidos em baias individuais durante 105 dias. Todos os animais foram pesados no início do experimento e a cada 35 dias e, ao final do confinamento, foram abatidos em frigorífico comercial para realização das medidas de características de carcaça. Os machos não-castrados apresentaram maior ingestão de nutrientes em comparação às fêmeas, tanto em valores absolutos quanto em valores relativos ao PC. Os machos castrados apresentaram valores intermediários e não diferiram dos não-castrados e das fêmeas. Os machos não-castrados apresentaram maior ganho de peso diário e desenvolvimento muscular, representado pela maior área de olho-de-lombo. Também foram mais eficientes quanto à conversão alimentar e ao rendimento de carcaça. Não houve efeito das dietas sobre a ingestão de nutrientes, à exceção do EE, que foi maior para a dieta com cana-de-açúcar + semente de girassol, com mais teor desse nutriente. As dietas também não influenciaram o desempenho dos animais. A dieta com silagem de milho mostrou-se economicamente mais viável para terminação de bovinos jovens em confinamento. Os machos não-castrados são os mais adequados para exploração de bovinos jovens em confinamento, independentemente da dieta.

As zonas de processamento de exportação como instrumento de desenvolvimento e redução das desigualdades regionais

The existence of inequalities among the Brazilian regions is an indeed fact along the country s history. Before this reality the constitutional legislator inserted into the Federal Constitution of 1988, as a purpose of the Federative Republic of Brazil, the reduction of regional inequalities. The development has also been included as a purpose from the State, because there is an straight relation with the reduction of regional inequalities. In both situations is searched the improvement of people s living conditions. . In pursuit of this achievement, the State must implement public policy, and, for this to happen, it needs the ingress of income inside of the public coffers and support of economic agents, therefore the importance of constitucionalization of the economic policy. The 1988 s Constitution adopted a rational capitalism regime consentaneous with current legal and social conceptions, that s why it enabled the State s intervention into economy to correct the so-called market failures or to make the established objectives fulfilled. About this last one, the intervention may happen by induction through the adoption of regulatory Standards of incentive or disincentive of economic activity. Among the possible inductive ways there are the tax assessments that aim to stimulate the economic agents behavior in view of finding that the development doesn t occur with the same intensity in all of the country s regions. Inside this context there are the Export Processing Zones (EPZs) which are special areas with different customs regime by the granting of benefits to the companies that are installed there. The EPZs have been used, by several countries, in order to develop certain regions, and economic indicators show that they promoted economic and social changes in the places where they are installed, especially because, by attracting companies, they provide job creation, industrialization and increased exports. In Brazil, they can contribute decisively to overcome major obstacles or decrease the attraction of economic agents and economic development of the country. In the case of an instrument known to be effective to achieve the goals established by the Constitution, it is duty of the Executive to push for the law that governs this customs regime is effectively applied. If the Executive doesn t fulfill this duty, incurs into unjustifiable omission, correction likely by the Judiciary, whose mission is to prevent acts or omissions contrary to constitutional order

Perdas de grãos e distribuição de palha na colheita mecanizada de soja

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)