Board-level prototype validation: a built-in controller and extended BST architecture

Prototype validation is a major concern in modern electronic product design and development. Simulation, structural test, functional and timing debug are all forming parts of the validation process, although very often addressed as dissociated tasks. In this paper we describe an integrated approach to board-level prototype validation, based on a set of mandatory/optional BST instructions and a built-in controller for debug and test, that addresses the late mentioned tasks as inherent parts of a whole process

An high-speed parametric ADC and a co-designed mixer for CMOS RF receivers

Dissertação apresentada na faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para a obtenção do grau de Mestre em Engenharia Electrotécnica e de Computadores

Fast mobility support in low-power wireless networks: smart-HOP over RPL/6LoWPAN

With the emergence of low-power wireless hardware new ways of communication were needed. In order to standardize the communication between these low powered devices the Internet Engineering Task Force (IETF) released the 6LoWPAN stand- ard that acts as an additional layer for making the IPv6 link layer suitable for the lower-power and lossy networks. In the same way, IPv6 Routing Protocol for Low- Power and Lossy Networks (RPL) has been proposed by the IETF Routing Over Low power and Lossy networks (ROLL) Working Group as a standard routing protocol for IPv6 routing in low-power wireless sensor networks. The research performed in this thesis uses these technologies to implement a mobility process. Mobility management is a fundamental yet challenging area in low-power wireless networks. There are applications that require mobile nodes to exchange data with a xed infrastructure with quality-of-service guarantees. A prime example of these applications is the monitoring of patients in real-time. In these scenarios, broadcast- ing data to all access points (APs) within range may not be a valid option due to the energy consumption, data storage and complexity requirements. An alternative and e cient option is to allow mobile nodes to perform hand-o s. Hand-o mechanisms have been well studied in cellular and ad-hoc networks. However, low-power wireless networks pose a new set of challenges. On one hand, simpler radios and constrained resources ask for simpler hand-o schemes. On the other hand, the shorter coverage and higher variability of low-power links require a careful tuning of the hand-o parameters. In this work, we tackle the problem of integrating smart-HOP within a standard protocol, speci cally RPL. The simulation results in Cooja indicate that the pro- posed scheme minimizes the hand-o delay and the total network overhead. The standard RPL protocol is simply unable to provide a reliable mobility support sim- ilar to other COTS technologies. Instead, they support joining and leaving of nodes, with very low responsiveness in the existence of physical mobility.

Scientist women perceptions of their work conditions and career development

This article reports preliminary findings about Portuguese scientist women’s perceptions of gender issues in their institutions. Empirical data have been collected by means of an electronic open questionnaire sent to the AMONET (Portuguese Association of Women in Science) members. Basically, the study aims to examine the degree of satisfaction with their profession, the difficulties they meet in everyday professional life, and whether they feel or have felt gender discrimination in their institutions. Findings show that all respondents feel happy or very happy with their profession. However, discrimination is mentioned by a significant percentage, even if such discrimination assumes, quite often, an elusive way, suggesting that higher institutions still discriminate against women. Findings, articulated with literature, also lead to discussion about power and leadership, both in the hands of male academics, in the majority of the institutions, as well as the clarification of different perceptions of ambition both by women and man.

Otimização estocástica para a exploração de centrais de concentração solar considerando incerteza e risco

Dissertação para obtenção do grau de Mestre em Engenharia Eletrotécnica

Paracoccidioides brasiliensis: a mycologic and immunochemical study of a sample isolated from an armadillo (Dasipus novencinctus)

A sample of P. brasiliensis isolated from the spleen and the liver of an armadillo (Dasipus novencinctus) has been analysed under a mycological and immunochemical viewpoint. The armadillo was captured in an area of Tucuruí (State of Pará, Brazil), the animal being already established as an enzootic reservoir of P. brasiliensis at that region of the country. This sample maintained in the fungal collection of the Tropical Medicine Institute of São Paulo (Brazil) numbered 135, has got all the characteristics of P. brasiliensis, with a strong antigenic power and low virulence for guinea-pigs and Wistar rats. The specific exoantigen of P. brasiliensis - the glycoprotein with a molecular weight of 43 kDa - was easily demonstrated with double immunodiffusion, immunoelectrophoresis, SDS-PAGE and immunobloting techniques.

Simulated Annealing Approach Applied to the Energy Resource Management Considering Demand Response for Electric Vehicle

The aggregation and management of Distributed Energy Resources (DERs) by an Virtual Power Players (VPP) is an important task in a smart grid context. The Energy Resource Management (ERM) of theses DERs can become a hard and complex optimization problem. The large integration of several DERs, including Electric Vehicles (EVs), may lead to a scenario in which the VPP needs several hours to have a solution for the ERM problem. This is the reason why it is necessary to use metaheuristic methodologies to come up with a good solution with a reasonable amount of time. The presented paper proposes a Simulated Annealing (SA) approach to determine the ERM considering an intensive use of DERs, mainly EVs. In this paper, the possibility to apply Demand Response (DR) programs to the EVs is considered. Moreover, a trip reduce DR program is implemented. The SA methodology is tested on a 32-bus distribution network with 2000 EVs, and the SA results are compared with a deterministic technique and particle swarm optimization results.

Demand Response Design and Use Based on Network Locational Marginal Prices

Power systems have been experiencing huge changes mainly due to the substantial increase of distributed generation (DG) and the operation in competitive environments. Virtual Power Players (VPP) can aggregate several players, namely a diversity of energy resources, including distributed generation (DG) based on several technologies, electric storage systems (ESS) and demand response (DR). Energy resources management gains an increasing relevance in this competitive context. This makes the DR use more interesting and flexible, giving place to a wide range of new opportunities. This paper proposes a methodology to support VPPs in the DR programs’ management, considering all the existing energy resources (generation and storage units) and the distribution network. The proposed method is based on locational marginal prices (LMP) values. The evaluation of the impact of using DR specific programs in the LMP values supports the manager decision concerning the DR use. The proposed method has been computationally implemented and its application is illustrated in this paper using a 33-bus network with intensive use of DG.

Real-Time Simulation of Real-Time Pricing Demand Response to Meet Wind Variations

Recent changes of paradigm in power systems opened the opportunity to the active participation of new players. The small and medium players gain new opportunities while participating in demand response programs. This paper explores the optimal resources scheduling in two distinct levels. First, the network operator facing large wind power variations makes use of real time pricing to induce consumers to meet wind power variations. Then, at the consumer level, each load is managed according to the consumer preferences. The two-level resources schedule has been implemented in a real-time simulation platform, which uses hardware for consumer’ loads control. The illustrative example includes a situation of large lack of wind power and focuses on a consumer with 18 loads.

Invited review: Models for the optimization of regional wastewater treatment systems

European Journal of Operational Research, nº 73 (1994)

Diagnóstico energético da indústria de pneus e sugestões de melhoria

Cada vez mais a indústria tem vindo a sofrer algumas mudanças no seu processo produtivo. Hoje, mais que nunca, é preciso garantir que as instalações produtivas sejam as mais eficientes possíveis, procurando a racionalização da energia com um decrescimento dos custos. Deste modo o objectivo desta dissertação é o diagnóstico energético na fábrica de pneus e sugestões de melhoria na empresa CNB/CAMAC. A realização de um diagnóstico energético, para a detecção de desperdícios de energia tem sido amplamente utilizada. A optimização irá prospectar potenciais de mudanças e aplicação de tecnologias de eficiência energética. Pretende-se deste modo travar o consumo energético sem que seja afectada a produção, já que a empresa é considerada consumidora intensiva de energia. Na empresa CNB/CAMAC há consumo de fuelóleo, gasóleo, vapor e energia eléctrica, sendo o vapor a forma de energia mais consumida (36,1%) seguido da energia eléctrica (33,8%), fuelóleo (29,9) e gasóleo (0,3%). O levantamento energético permitiu estudar a influência de algumas variáveis, nos consumos anuais da energia, e assim apresentar propostas de melhoria. Uma das propostas analisadas foi a possibilidade de efectuar um isolamento térmico a algumas válvulas no equipamento de produção e distribuição de vapor. Este isolamento conduziria a uma poupança de 33.540 kWh/ano. Também se propôs o isolamento dos tubos de transporte de vapor no sector da vulcanização o que geraria uma poupança de 549.826 kWh/ano. Sugere-se a implementação de um economizador na caldeira nº1 uma vez que a temperatura média dos gases de chaminé se situa á volta dos 311ºC. Uma vez que existe a pré instalação de um sistema de cogeração, sugere-se que este seja finalizado. Propôs-se a implementação de balastros electrónicos, que conduziria a uma diminuição em energia eléctrica de 33.5877 kWh/ano. Também se propõe a eliminação das fugas de ar na rede de distribuição do ar comprimido poupando assim 12,96kW/h.

Linear amplification with multiple nonlinear devices

Dissertação para obtenção do Grau de Mestre em Engenharia Electrotécnica e Computadores

Estudo de Ferramentas FEA Comerciais na Simulação Numérica de Processos de Conformação de Chapas Metálicas. Aplicação à Indústria Automóvel.

Os componentes obtidos através da conformação plástica de chapas têm uma grande importância, tanto na etapa de concepção do produto como na etapa de produção na indústria automóvel. Isto comprova-se pelo facto de, em média, cada automóvel integrar cerca de 500 componentes estampados para construir o chassis e a carroçaria [Alves 2003]. Deste total de componentes, 50 são de grandes dimensões (portas, tejadilho, painéis inferior e laterais, entre outros) e necessitam, em média, de cinco ferramentas para o seu fabrico, sendo o custo estimado para cada ferramenta de 230 000 € [Col 2000, Alves 2003]. Para além da indústria automóvel, a conformação plástica de chapas metálicas é um processo tecnológico presente nas indústrias relativas à aeroespacial, petrolífera, decoração, alimentar, entre outras. Do ponto de vista do enquadramento económico, cerca de 20% do custo total de um automóvel novo é devido à incorporação de componentes metálicos estampados. [Alves 2003]. A pressão do “Mercado Global” faz com que os custos relativos à matéria-prima, energia e mão-de-obra sejam uma constante em termos de redução do seu impacte no orçamento das empresas fornecedoras destes produtos. É neste contexto que surge a necessidade da realização deste estudo de Benchmark de Softwares, tornando-se bastante importante, quer ao nível da competitividade industrial, quer ao nível da inovação para novos produtos. A análise por elementos finitos desempenha um papel primordial no tryout virtual e otimização das ferramentas e processos de conformação plástica. Os objetivos principais deste estudo de simulação numérica são a identificação e comparação dos resultados obtidos pelo AUTOFORM e pelo PAMSTAMP, para cada uma das variáveis identificadas como as mais influentes na robustez dos processos de estampagem de chapa metálica. Estas variáveis identificadas são: consumo de material (Draw-in) após conformação; forças de conformação; valores de variação de espessura e dos valores de extensão e resultados de Springback. Os resultados obtidos são comparados com os resultados experimentais e, desta forma, avalia-se a capacidade inovadora e a eficácia de cada um dos softwares, obtendo-se assim, uma orientação mais real para o software mais indicado aos objetivos impostos pela indústria automóvel. Para este efeito, a indústria automóvel, como maior impulsionador e motor da investigação na área da simulação numérica aplicada aos processos de estampagem, tem aderido em peso ao Benchmarking. Um exemplo disto, é o que acontece nas conferências Numisheet. O Benchmark #2 da conferência Numisheet 2008 é analisado pormenorizadamente e os resultados numéricos e experimentais são comparados e apresentados. Dois materiais distintos (aço HC260LAD e liga de alumínio AC170), assim como três modelos com geometrias diferentes (com e sem freios) são apresentados neste relatório. Com vista à redução dos ciclos tentativa-erro, tem-se adotado ciclos virtuais ou numéricos e tem-se incrementado a interatividade entre as fases de concepção e projeto, num conceito muito próprio, mas cada vez mais abrangente, denominado “produção virtual”. É nesta filosofia que se insere a simulação numérica dos processos de conformação de chapa.

Optimization of fMRI Processing Parameters for Simutaneous Acquisition of EEG/fMRI in Focal Epilepsy

In the context of focal epilepsy, the simultaneous combination of electroencephalography (EEG) and functional magnetic resonance imaging (fMRI) holds a great promise as a technique by which the hemodynamic correlates of interictal spikes detected on scalp EEG can be identified. The fact that traditional EEG recordings have not been able to overcome the difficulty in correlating the ictal clinical symptoms to the onset in particular areas of the lobes, brings the need of mapping with more precision the epileptogenic cortical regions. On the other hand, fMRI suggested localizations more consistent with the ictal clinical manifestations detected. This study was developed in order to improve the knowledge about the way parameters involved in the physical and mathematical data, produced by the EEG/fMRI technique processing, would influence the final results. The evaluation of the accuracy was made by comparing the BOLD results with: the high resolution EEG maps; the malformative lesions detected in the T1 weighted MR images; and the anatomical localizations of the diagnosed symptomatology of each studied patient. The optimization of the set of parameters used, will provide an important contribution to the diagnosis of epileptogenic focuses, in patients included on an epilepsy surgery evaluation program. The results obtained allowed us to conclude that: by associating the BOLD effect with interictal spikes, the epileptogenic areas are mapped to localizations different from those obtained by the EEG maps representing the electrical potential distribution across the scalp (EEG); there is an important and solid bond between the variation of particular parameters (manipulated during the fMRI data processing) and the optimization of the final results, from which smoothing, deleted volumes, HRF (used to convolve with the activation design), and the shape of the Gamma function can be certainly emphasized.

Interoperability on low power devices

Dissertação para obtenção do Grau de Mestre em Engenharia Electrotécnica e de Computadores